| 1 |
<pre>Network Working Group K. Tesink, Editor |
| 2 |
Request for Comments: 2515 Bell Communications Research |
| 3 |
Obsoletes: <a href="./rfc1695">1695</a> February 1999 |
| 4 |
Category: Standards Track |
| 5 |
|
| 6 |
|
| 7 |
<span class="h1">Definitions of Managed Objects</span> |
| 8 |
<span class="h1">for ATM Management</span> |
| 9 |
|
| 10 |
Status of this Memo |
| 11 |
|
| 12 |
This document specifies an Internet standards track protocol for the |
| 13 |
Internet community, and requests discussion and suggestions for |
| 14 |
improvements. Please refer to the current edition of the "Internet |
| 15 |
Official Protocol Standards" (STD 1) for the standardization state |
| 16 |
and status of this protocol. Distribution of this memo is unlimited. |
| 17 |
|
| 18 |
Copyright Notice |
| 19 |
|
| 20 |
Copyright (C) The Internet Society (1999). All Rights Reserved. |
| 21 |
|
| 22 |
Table of Contents |
| 23 |
|
| 24 |
<a href="#section-1">1</a> Abstract ............................................. <a href="#page-2">2</a> |
| 25 |
<a href="#section-2">2</a> The SNMP Network Management Framework ................. <a href="#page-2">2</a> |
| 26 |
<a href="#section-3">3</a> ATM Terminology ....................................... <a href="#page-3">3</a> |
| 27 |
<a href="#section-3.1">3.1</a> VCL/VPL and VCC/VPC ................................. <a href="#page-3">3</a> |
| 28 |
<a href="#section-3.2">3.2</a> PVC, SVC and Soft PVC ............................... <a href="#page-5">5</a> |
| 29 |
<a href="#section-3.3">3.3</a> Traffic Management Parameters ....................... <a href="#page-6">6</a> |
| 30 |
<a href="#section-3.3.1">3.3.1</a> Traffic Policing and Traffic Shaping Parameters |
| 31 |
.................................................... <a href="#page-6">6</a> |
| 32 |
<a href="#section-3.3.2">3.3.2</a> Cell Loss Priority ................................ <a href="#page-6">6</a> |
| 33 |
<a href="#section-3.3.3">3.3.3</a> QoS Class ......................................... <a href="#page-6">6</a> |
| 34 |
<a href="#section-3.3.4">3.3.4</a> Service Category .................................. <a href="#page-7">7</a> |
| 35 |
<a href="#section-3.4">3.4</a> Max Active and Max Current VPI and VCI Bits ......... <a href="#page-7">7</a> |
| 36 |
<a href="#section-4">4</a> Overview .............................................. <a href="#page-8">8</a> |
| 37 |
<a href="#section-4.1">4.1</a> Background .......................................... <a href="#page-8">8</a> |
| 38 |
<a href="#section-4.2">4.2</a> Structure of the MIB ................................ <a href="#page-9">9</a> |
| 39 |
<a href="#section-4.3">4.3</a> ATM Interface Configuration Table ................... <a href="#page-9">9</a> |
| 40 |
<a href="#section-4.4">4.4</a> ATM Interface DS3 PLCP and TC Layer Tables .......... <a href="#page-9">9</a> |
| 41 |
<a href="#section-4.5">4.5</a> ATM Virtual Link and Cross-Connect Tables ........... <a href="#page-9">9</a> |
| 42 |
<a href="#section-5">5</a> Application of MIB II to ATM .......................... <a href="#page-10">10</a> |
| 43 |
<a href="#section-5.1">5.1</a> The System Group .................................... <a href="#page-10">10</a> |
| 44 |
<a href="#section-5.2">5.2</a> The Interface Group ................................. <a href="#page-10">10</a> |
| 45 |
<a href="#section-5.2.1">5.2.1</a> Support of the ATM Cell Layer by ifTable .......... <a href="#page-10">10</a> |
| 46 |
<a href="#section-6">6</a> Support of the AAL3/4 Based Interfaces ................ <a href="#page-12">12</a> |
| 47 |
<a href="#section-7">7</a> Support of the AAL5 Managed Objects ................... <a href="#page-12">12</a> |
| 48 |
<a href="#section-7.1">7.1</a> Managing AAL5 in a Switch ........................... <a href="#page-12">12</a> |
| 49 |
|
| 50 |
|
| 51 |
|
| 52 |
<span class="grey">Tesink Standards Track [Page 1]</span></pre> |
| 53 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-2" ></span> |
| 54 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 55 |
|
| 56 |
|
| 57 |
<a href="#section-7.2">7.2</a> Managing AAL5 in a Host ............................. <a href="#page-14">14</a> |
| 58 |
<a href="#section-7.3">7.3</a> Support of AAL5 by ifTable .......................... <a href="#page-15">15</a> |
| 59 |
7.4 Support of Proprietary Virtual Interface by ifT- |
| 60 |
able ............................................... <a href="#page-16">16</a> |
| 61 |
<a href="#section-7.5">7.5</a> AAL5 Connection Performance Statistics Table ........ <a href="#page-17">17</a> |
| 62 |
<a href="#section-8">8</a> ILMI MIBs and the ATM Managed Objects ................. <a href="#page-18">18</a> |
| 63 |
<a href="#section-9">9</a> Definitions ........................................... <a href="#page-20">20</a> |
| 64 |
<a href="#section-10">10</a> Acknowledgments ...................................... <a href="#page-83">83</a> |
| 65 |
<a href="#section-11">11</a> References ........................................... <a href="#page-83">83</a> |
| 66 |
<a href="#section-12">12</a> Security Considerations .............................. <a href="#page-85">85</a> |
| 67 |
<a href="#section-13">13</a> Author's Address ..................................... <a href="#page-85">85</a> |
| 68 |
<a href="#section-14">14</a> Intellectual Property ................................ <a href="#page-86">86</a> |
| 69 |
<a href="#section-15">15</a> Full Copyright Statement ............................. <a href="#page-87">87</a> |
| 70 |
|
| 71 |
<span class="h2"><a class="selflink" id="section-1" href="#section-1">1</a>. Abstract</span> |
| 72 |
|
| 73 |
This memo defines a portion of the Management Information Base (MIB) |
| 74 |
for use with network management protocols in the Internet community. |
| 75 |
In particular, it describes objects used for managing ATM-based |
| 76 |
interfaces, devices, networks and services. |
| 77 |
|
| 78 |
This memo replaces <a href="./rfc1695">RFC 1695</a> [<a href="#ref-24" title=""Definitions of Managed Objects for ATM Management Version 8.0 using SMIv2"">24</a>]. Changes relative to <a href="./rfc1695">RFC 1695</a> are |
| 79 |
summarized in the MIB module's REVISION clause. |
| 80 |
|
| 81 |
Textual Conventions used in this MIB are defined in [<a href="#ref-6" title=""Textual Conventions for Version 2 of the Simple Network Management Protocol (SNMPv2)"">6</a>] and [<a href="#ref-19" title=""Definitions of Textual Conventions and OBJECT-IDENTITIES for ATM Management"">19</a>]. |
| 82 |
|
| 83 |
<span class="h2"><a class="selflink" id="section-2" href="#section-2">2</a>. The SNMP Network Management Framework</span> |
| 84 |
|
| 85 |
The SNMP Management Framework presently consists of five major |
| 86 |
components: |
| 87 |
|
| 88 |
0 An overall architecture, described in <a href="./rfc2271">RFC 2271</a> [<a href="#ref-1" title=""An Architecture for Describing SNMP Management Frameworks"">1</a>]. |
| 89 |
|
| 90 |
0 Mechanisms for describing and naming objects and events |
| 91 |
for the purpose of management. The first version of this |
| 92 |
Structure of Management Information (SMI) is called SMIv1 and |
| 93 |
described in STD 16, <a href="./rfc1155">RFC 1155</a> [<a href="#ref-2" title=""Structure and Identification of Management Information for TCP/IP-based Internets"">2</a>], STD 16, <a href="./rfc1212">RFC 1212</a> [<a href="#ref-3" title=""Concise MIB Definitions"">3</a>] and <a href="./rfc1215">RFC</a> |
| 94 |
<a href="./rfc1215">1215</a> [<a href="#ref-4" title=""A Convention for Defining Traps for use with the SNMP"">4</a>]. The second version, called SMIv2, is described in <a href="./rfc1902">RFC</a> |
| 95 |
<a href="./rfc1902">1902</a> [<a href="#ref-5" title=""Structure of Management Information for Version 2 of the Simple Network Management Protocol (SNMPv2)"">5</a>], <a href="./rfc1903">RFC 1903</a> [<a href="#ref-6" title=""Textual Conventions for Version 2 of the Simple Network Management Protocol (SNMPv2)"">6</a>] and <a href="./rfc1904">RFC 1904</a> [<a href="#ref-7" title=""Conformance Statements for Version 2 of the Simple Network Management Protocol (SNMPv2)"">7</a>]. |
| 96 |
|
| 97 |
0 Message protocols for transferring management information. The |
| 98 |
first version of the SNMP message protocol is called SNMPv1 and |
| 99 |
described in STD 15, <a href="./rfc1157">RFC 1157</a> [<a href="#ref-8" title=""Simple Network Management Protocol"">8</a>]. A second version of the SNMP |
| 100 |
message protocol, which is not an Internet standards track |
| 101 |
protocol, is called SNMPv2c and described in <a href="./rfc1901">RFC 1901</a> [<a href="#ref-9" title=""Introduction to Community-based SNMPv2"">9</a>] and |
| 102 |
<a href="./rfc1906">RFC 1906</a> [<a href="#ref-10" title=""Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2)"">10</a>]. |
| 103 |
|
| 104 |
|
| 105 |
|
| 106 |
|
| 107 |
|
| 108 |
<span class="grey">Tesink Standards Track [Page 2]</span></pre> |
| 109 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-3" ></span> |
| 110 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 111 |
|
| 112 |
|
| 113 |
The third version of the message protocol is called SNMPv3 and |
| 114 |
described in <a href="./rfc1906">RFC 1906</a> [<a href="#ref-10" title=""Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2)"">10</a>], <a href="./rfc2272">RFC 2272</a> [<a href="#ref-11" title=""Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)"">11</a>] and <a href="./rfc2274">RFC 2274</a> [<a href="#ref-12" title=""User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)"">12</a>]. |
| 115 |
|
| 116 |
0 Protocol operations for accessing management information. The |
| 117 |
first set of protocol operations and associated PDU formats is |
| 118 |
described in STD 15, <a href="./rfc1157">RFC 1157</a> [<a href="#ref-8" title=""Simple Network Management Protocol"">8</a>]. A second set of protocol |
| 119 |
operations and associated PDU formats is described in <a href="./rfc1905">RFC 1905</a> |
| 120 |
[<a href="#ref-13" title=""Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)"">13</a>]. |
| 121 |
|
| 122 |
0 A set of fundamental applications described in <a href="./rfc2273">RFC 2273</a> [<a href="#ref-14" title="MPv3 Applications"">14</a>] and |
| 123 |
the view-based access control mechanism described in <a href="./rfc2275">RFC 2275</a> |
| 124 |
[<a href="#ref-15" title=""View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)"">15</a>]. |
| 125 |
|
| 126 |
Managed objects are accessed via a virtual information store, termed |
| 127 |
the Management Information Base or MIB. Objects in the MIB are |
| 128 |
defined using the mechanisms defined in the SMI. |
| 129 |
|
| 130 |
This memo specifies a MIB module that is compliant to the SMIv2. A |
| 131 |
MIB conforming to the SMIv1 can be produced through the appropriate |
| 132 |
translations. The resulting translated MIB must be semantically |
| 133 |
equivalent, except where objects or events are omitted because no |
| 134 |
translation is possible (e.g., use of Counter64). Some machine |
| 135 |
readable information in SMIv2 will be converted into textual |
| 136 |
descriptions in SMIv1 during the translation process. However, this |
| 137 |
loss of machine readable information is not considered to change the |
| 138 |
semantics of the MIB. |
| 139 |
|
| 140 |
<span class="h2"><a class="selflink" id="section-3" href="#section-3">3</a>. ATM Terminology</span> |
| 141 |
|
| 142 |
Some basic ATM terminologies are described in this section to |
| 143 |
facilitate defining the ATM managed objects. |
| 144 |
|
| 145 |
<span class="h3"><a class="selflink" id="section-3.1" href="#section-3.1">3.1</a>. VCL/VPL and VCC/VPC</span> |
| 146 |
|
| 147 |
There are two distinct types of ATM virtual connections: Virtual |
| 148 |
Channel Connections (VCCs) and Virtual Path Connection (VPCs). As |
| 149 |
shown in Figures 1 and 2, ATM virtual connections consist of |
| 150 |
concatenated series of virtual links which forms a path between two |
| 151 |
end points, with each concatenation occurring at an ATM switch. |
| 152 |
Virtual links of VCCs are called Virtual Channel Links (VCLs). |
| 153 |
Virtual links of VPCs are called Virtual Path Links (VPLs). The VCI |
| 154 |
and VPI fields in the ATM cell header associate each cell of a VCC |
| 155 |
with a particular VCL over a given physical link. The VPI field in |
| 156 |
the ATM cell header associates each cell of a VPC with a particular |
| 157 |
VPL over a given physical link. Switches route cells between VCLs |
| 158 |
(or VPLs) via a cross-connect function according to the cells' |
| 159 |
VCI/VPI (or VPI) values. |
| 160 |
|
| 161 |
|
| 162 |
|
| 163 |
|
| 164 |
<span class="grey">Tesink Standards Track [Page 3]</span></pre> |
| 165 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-4" ></span> |
| 166 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 167 |
|
| 168 |
|
| 169 |
<-----------------------VCC--------------------------> |
| 170 |
------------ ----------- |
| 171 |
|ATM | |ATM | |
| 172 |
|X-Connect | |X-Connect | |
| 173 |
VCL1 |Point | VCL2 |Point | VCL3 |
| 174 |
O---------|----X-----|-------|-----|----X-----|-------O |
| 175 |
| | | | |
| 176 |
------------ ------------ |
| 177 |
ATM Switch ATM Switch |
| 178 |
|
| 179 |
|
| 180 |
Figure 1: Virtual Channel Links and |
| 181 |
Virtual Channel Connection |
| 182 |
|
| 183 |
|
| 184 |
|
| 185 |
<-----------------------VPC--------------------------> |
| 186 |
------------ ----------- |
| 187 |
|ATM | |ATM | |
| 188 |
|X-Connect | |X-Connect | |
| 189 |
VPL1 |Point | VPL2 |Point | VPL3 |
| 190 |
O---------|----X-----|-------|-----|----X-----|-------O |
| 191 |
| | | | |
| 192 |
------------ ------------ |
| 193 |
ATM Switch ATM Switch |
| 194 |
|
| 195 |
|
| 196 |
Figure 2: Virtual Path Links and |
| 197 |
Virtual Path Connection |
| 198 |
|
| 199 |
|
| 200 |
A single ATM end-system or switch does not support the whole end-to- |
| 201 |
end span of a VCC (or VPC). Rather, multiple ATM end-systems and/or |
| 202 |
switches each support one piece of the VCC (or VPC). That is, each |
| 203 |
ATM end-system (or ATM switch) at one end of the VCC/VPC supports its |
| 204 |
end of the VCC/VPC plus the VCL or VPL on its external interface, and |
| 205 |
each switch through which the VCC/VPC passes supports the pair of |
| 206 |
VCLs/VPLs on its external interfaces as well as the cross-connection |
| 207 |
of those VCLs/VPLs. Thus, the end-to-end management of a VCC or VPC |
| 208 |
is achieved only by appropriate management of its individual pieces |
| 209 |
in combination. |
| 210 |
|
| 211 |
Note that for management purposes, an ATM network may be viewed as a |
| 212 |
large distributed switch by hiding all the network's internal |
| 213 |
connectivity as being internal to the distributed switch (as shown in |
| 214 |
Figure 2a). This model may for example be used for Customer Network |
| 215 |
Management (CNM) purposes. |
| 216 |
|
| 217 |
|
| 218 |
|
| 219 |
|
| 220 |
<span class="grey">Tesink Standards Track [Page 4]</span></pre> |
| 221 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-5" ></span> |
| 222 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 223 |
|
| 224 |
|
| 225 |
<---------------------VCC---------------------------> |
| 226 |
-------------------------------------- |
| 227 |
| | |
| 228 |
| ---------- ---------- | |
| 229 |
| | ATM | | ATM | | |
| 230 |
VCL1 | | Switch | | Switch | | VCL3 |
| 231 |
O-------|-|--------|------/-------|--------|-|------O |
| 232 |
| | | | | | |
| 233 |
| ---------- ---------- | |
| 234 |
| | |
| 235 |
| ATM Network | |
| 236 |
-------------------------------------- |
| 237 |
|
| 238 |
|
| 239 |
Figure 2a: ATM Network modeled as a large distributed |
| 240 |
switch |
| 241 |
|
| 242 |
A VCC has a set of traffic characteristics (i.e., bandwidth |
| 243 |
parameters, service category parameters, etc.). VCLs inherit their |
| 244 |
traffic characteristics from the VCC of which they are a part. VCCs |
| 245 |
are bi-directional by definition. However, the traffic parameters in |
| 246 |
the two directions of a connection can be symmetric or asymmetric, |
| 247 |
i.e., the two directions can have the same or different traffic |
| 248 |
flows. A uni-directional traffic flow across a VCC is achieved by |
| 249 |
assigning a zero bandwidth in one direction. Note that in addition |
| 250 |
to the bandwidth required by the user traffic flow, bandwidth is also |
| 251 |
required for OAM cell flows, even for the zero-bandwidth direction of |
| 252 |
a uni-directional connection. These same principles apply to VPCs. |
| 253 |
|
| 254 |
<span class="h3"><a class="selflink" id="section-3.2" href="#section-3.2">3.2</a>. PVC, SVC and Soft PVC</span> |
| 255 |
|
| 256 |
A Permanent Virtual Connection (PVC) is a provisioned VCC or VPC. A |
| 257 |
Switched Virtual Connection (SVC) is a switched VCC or VPC that is |
| 258 |
set up in real-time via call set-up signaling procedures. A PVC (or |
| 259 |
an SVC) can be a point-to-point, point-to-multipoint, or multipoint- |
| 260 |
to-multipoint VCC or VPC. A Soft PVC is a connection of which |
| 261 |
portions are switched, while other portions are permanent (see Figure |
| 262 |
3 and [<a href="#ref-22" title=""ATM Forum Private Network-Network Interface Specification, Version 1.0 (PNNI 1.0)"">22</a>]). |
| 263 |
|
| 264 |
|
| 265 |
+--------+ +--------+ +--------+ |
| 266 |
pvc| ATM |svc svc | ATM |svc svc | ATM |pvc |
| 267 |
----| Switch |-----------| Switch |-----------| Switch |---- |
| 268 |
+--------+ +--------+ +--------+ |
| 269 |
|
| 270 |
Figure 3: An example of a Soft PVC |
| 271 |
|
| 272 |
|
| 273 |
|
| 274 |
|
| 275 |
|
| 276 |
<span class="grey">Tesink Standards Track [Page 5]</span></pre> |
| 277 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-6" ></span> |
| 278 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 279 |
|
| 280 |
|
| 281 |
<span class="h3"><a class="selflink" id="section-3.3" href="#section-3.3">3.3</a>. Traffic Management Parameters</span> |
| 282 |
|
| 283 |
<span class="h4"><a class="selflink" id="section-3.3.1" href="#section-3.3.1">3.3.1</a>. Traffic Policing and Traffic Shaping Parameters</span> |
| 284 |
|
| 285 |
In order to allocate resources fairly among different users, some |
| 286 |
networks police traffic at resource access points. The traffic |
| 287 |
enforcement or policing taken at a UNI is called Usage Parameter |
| 288 |
Control (UPC) and is conceptually activated on an incoming VCL or VPL |
| 289 |
as shown in Figure 4. The use of the traffic enforcer at the ingress |
| 290 |
of the connection is to make sure that the user traffic does not |
| 291 |
exceed the negotiated traffic parameters such as the peak cell rate |
| 292 |
associated with a specific traffic descriptor type. |
| 293 |
|
| 294 |
---------- ---------- |
| 295 |
UNI | ATM | NNI | ATM | UNI |
| 296 |
| | switch | | | switch | | |
| 297 |
O<---|---->X(UPC) |<----|------>| (UPC)X<-----|--->O |
| 298 |
| VCL | | | VCL | | VCL | |
| 299 |
---------- ---------- |
| 300 |
|
| 301 |
|
| 302 |
Figure 4: An Example of a UPC |
| 303 |
|
| 304 |
In addition, traffic shaping may be performed on an outgoing VPL or |
| 305 |
VCL at a given ATM interface. The function of the ATM traffic |
| 306 |
shaper, conceptually either at the source or an egress point of the |
| 307 |
connection, is to smooth the outgoing cell traffic inter-arrival |
| 308 |
time. If policing or shaping is not performed then the policing or |
| 309 |
shaping algorithm is not activated. |
| 310 |
|
| 311 |
<span class="h4"><a class="selflink" id="section-3.3.2" href="#section-3.3.2">3.3.2</a>. Cell Loss Priority</span> |
| 312 |
|
| 313 |
To prioritize traffic during resource congestion, ATM cells are |
| 314 |
assigned one of the two types of Cell Loss Priority (CLP), CLP=0 and |
| 315 |
CLP=1. ATM cells with CLP=0 have a higher priority in regard to cell |
| 316 |
loss than ATM cells with CLP=1. Therefore, during resource |
| 317 |
congestions, CLP=1 cells are dropped before any CLP=0 cell is |
| 318 |
dropped. |
| 319 |
|
| 320 |
<span class="h4"><a class="selflink" id="section-3.3.3" href="#section-3.3.3">3.3.3</a>. QoS Class</span> |
| 321 |
|
| 322 |
<a href="./rfc1695">RFC1695</a> specified that one of a number of Quality of Service (QoS) |
| 323 |
classes is assigned to a VCC or VPC by associating the object |
| 324 |
atmTrafficQoSClass with each VCL or VPL. However, new insights in |
| 325 |
ATM traffic management have caused this object to be deprecated. |
| 326 |
|
| 327 |
|
| 328 |
|
| 329 |
|
| 330 |
|
| 331 |
|
| 332 |
<span class="grey">Tesink Standards Track [Page 6]</span></pre> |
| 333 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-7" ></span> |
| 334 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 335 |
|
| 336 |
|
| 337 |
<span class="h4"><a class="selflink" id="section-3.3.4" href="#section-3.3.4">3.3.4</a>. Service Category</span> |
| 338 |
|
| 339 |
Replacing QoS Class, VPLs and VCLs are qualified in terms of their |
| 340 |
service category (atmServiceCategory). When properly configured, VCLs |
| 341 |
(or VPLs) concatenated to form a VCC (or VPC) will all have the same |
| 342 |
service category class as that of the VCC (or VPC). |
| 343 |
|
| 344 |
<span class="h3"><a class="selflink" id="section-3.4" href="#section-3.4">3.4</a>. Max Active and Max Current VPI and VCI Bits</span> |
| 345 |
|
| 346 |
A manager may wish to configure the maximum number of VPI and VCI |
| 347 |
bits that can be used to identify VPIs and VCIs on a given ATM |
| 348 |
interface. This value can be less than or equal to the maximum |
| 349 |
number of bits supported by the interface hardware, and is referred |
| 350 |
to in the MIB as the Max Active VPI Bits and Max Active VCI Bits. |
| 351 |
|
| 352 |
However, a manager may not be able to configure the Max Active Bits |
| 353 |
on both ends of an ATM link. For example, the manager may not be |
| 354 |
allowed write access to the peer's MIB, or there may be hardware |
| 355 |
limitations on the peer device. Therefore, the two ATM devices may |
| 356 |
use ILMI to negotiate "Max Current" VPI and VCI bits, which is the |
| 357 |
maximum number of bits that both interfaces are willing to support. |
| 358 |
This is illustrated in Figure 5. The relationship between the |
| 359 |
different parameters is illustrated in Figure 6. Note that if ILMI |
| 360 |
negotiation is not supported, then the devices have no choice but to |
| 361 |
use the configured Max Active bits, and assume that it has been |
| 362 |
configured to the same value on both ends of the link. |
| 363 |
|
| 364 |
|
| 365 |
+--------+ +--------+ +--------+ |
| 366 |
| ATM | IF a IF b | ATM | IF c IF d | ATM | |
| 367 |
| Device |--------------| Device |--------------| Device | |
| 368 |
+--------+ +--------+ +--------+ |
| 369 |
|
| 370 |
IF a: Max Active VPI Bits = 6 (configured) |
| 371 |
Max Current VPI Bits = 6 (negotiated) |
| 372 |
|
| 373 |
IF b: Max Active VPI Bits = 8 (configured) |
| 374 |
Max Current VPI Bits = 6 (negotiated) |
| 375 |
|
| 376 |
IF c: Max Active VPI Bits = 8 (configured) |
| 377 |
Max Current VPI Bits = 8 (negotiated) |
| 378 |
|
| 379 |
IF d: Max Active VPI Bits = 8 (configured) |
| 380 |
Max Current VPI Bits = 8 (negotiated) |
| 381 |
|
| 382 |
|
| 383 |
|
| 384 |
|
| 385 |
|
| 386 |
|
| 387 |
|
| 388 |
<span class="grey">Tesink Standards Track [Page 7]</span></pre> |
| 389 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-8" ></span> |
| 390 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 391 |
|
| 392 |
|
| 393 |
(between IF a and IF b, the minimum of the two configured |
| 394 |
"Max Active VPI Bits" is 6, so both interfaces set their |
| 395 |
"Max Current VPI Bits" to 6. Since IF c and IF d both |
| 396 |
are configured with "Max Active VPI Bits" of 8, they |
| 397 |
set their "Max Current VPI Bits" to 8.) |
| 398 |
|
| 399 |
Figure 5 |
| 400 |
|
| 401 |
|
| 402 |
MSB LSB |
| 403 |
+----------------------------------------------------+ |
| 404 |
| | | | | |
| 405 |
+----------------------------------------------------+ |
| 406 |
^ ^ ^ ^ |
| 407 |
| | | | |
| 408 |
Max bits Max Bits Max Max |
| 409 |
supported supported Active (config.) current (negotiated) |
| 410 |
by MIB by h/w Bits Bits |
| 411 |
|
| 412 |
Figure 6 |
| 413 |
|
| 414 |
<span class="h2"><a class="selflink" id="section-4" href="#section-4">4</a>. Overview</span> |
| 415 |
|
| 416 |
ATM management objects are used to manage ATM interfaces, ATM virtual |
| 417 |
links, ATM cross-connects, AAL5 entities and AAL5 connections |
| 418 |
supported by ATM hosts, ATM switches and ATM networks. This section |
| 419 |
provides an overview and background of how to use this MIB and other |
| 420 |
potential MIBs for this purpose. |
| 421 |
|
| 422 |
The purpose of this memo is primarily to manage ATM PVCs. ATM SVCs |
| 423 |
are also represented by the management information in this MIB. |
| 424 |
However, full management of SVCs may require additional capabilities |
| 425 |
which are beyond the scope of this memo. |
| 426 |
|
| 427 |
<span class="h3"><a class="selflink" id="section-4.1" href="#section-4.1">4.1</a>. Background</span> |
| 428 |
|
| 429 |
In addition to the MIB module defined in this memo, other MIB modules |
| 430 |
are necessary to manage ATM interfaces, links and cross-connects. |
| 431 |
Examples include MIB II for general system and interface management |
| 432 |
[<a href="#ref-16" title=""Management Information Base for Network Management of TCP/IP-based internets: MIB-II"">16</a>][17], the DS3 or SONET MIBs for management of physical |
| 433 |
interfaces, and, as appropriate, MIB modules for applications that |
| 434 |
make use of ATM, such as SMDS. These MIB modules are outside the |
| 435 |
scope of this specification. |
| 436 |
|
| 437 |
The current specification of this ATM MIB is based on SNMPv2-SMI. |
| 438 |
|
| 439 |
|
| 440 |
|
| 441 |
|
| 442 |
|
| 443 |
|
| 444 |
<span class="grey">Tesink Standards Track [Page 8]</span></pre> |
| 445 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-9" ></span> |
| 446 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 447 |
|
| 448 |
|
| 449 |
<span class="h3"><a class="selflink" id="section-4.2" href="#section-4.2">4.2</a>. Structure of the MIB</span> |
| 450 |
|
| 451 |
The managed ATM objects are arranged into the following tables: |
| 452 |
|
| 453 |
(1) ATM interface configuration table |
| 454 |
(2) ATM interface DS3 PLCP and TC sublayer tables |
| 455 |
(3) ATM traffic parameter table |
| 456 |
(4) ATM interface virtual link (VPL/VCL) configuration |
| 457 |
tables |
| 458 |
(5) ATM VP/VC cross-connect tables |
| 459 |
(6) AAL5 connection performance statistics table |
| 460 |
|
| 461 |
Note that, managed objects for activation/deactivation of OAM cell |
| 462 |
flows and ATM traps notifying virtual connection or virtual link |
| 463 |
failures are outside the scope of this memo. |
| 464 |
|
| 465 |
<span class="h3"><a class="selflink" id="section-4.3" href="#section-4.3">4.3</a>. ATM Interface Configuration Table</span> |
| 466 |
|
| 467 |
This table contains information on ATM cell layer configuration of |
| 468 |
local ATM interfaces on an ATM device in addition to the information |
| 469 |
on such interfaces contained in the ifTable. |
| 470 |
|
| 471 |
<span class="h3"><a class="selflink" id="section-4.4" href="#section-4.4">4.4</a>. ATM Interface DS3 PLCP and TC Layer Tables</span> |
| 472 |
|
| 473 |
These tables provide performance statistics of the DS3 PLCP and TC |
| 474 |
sublayer of local ATM interfaces on a managed ATM device. DS3 PLCP |
| 475 |
and TC sublayer are currently used to carry ATM cells respectively |
| 476 |
over DS3 and SONET transmission paths. |
| 477 |
|
| 478 |
<span class="h3"><a class="selflink" id="section-4.5" href="#section-4.5">4.5</a>. ATM Virtual Link and Cross-Connect Tables</span> |
| 479 |
|
| 480 |
ATM virtual link and cross-connect tables model bi-directional ATM |
| 481 |
virtual links and ATM cross-connects. The ATM VP/VC link tables are |
| 482 |
implemented in an ATM host, ATM switch and ATM network. The ATM |
| 483 |
switch and ATM network also implement the ATM VP/VC cross-connect |
| 484 |
tables. Both link and cross-connect tables are implemented in a |
| 485 |
carrier's network for Customer Network Management (CNM) purposes. |
| 486 |
|
| 487 |
The ATM virtual link tables are used to create, delete or modify ATM |
| 488 |
virtual links in an ATM host, ATM switch and ATM network. ATM |
| 489 |
virtual link tables along with the cross-connect tables are used to |
| 490 |
create, delete or modify ATM cross-connects in an ATM switch or ATM |
| 491 |
network (e.g., for CNM purposes). |
| 492 |
|
| 493 |
For a PVC, the cross-connect between two VPLs is represented in the |
| 494 |
atmVpCrossConnectTable of the ATM-MIB, indexed by the |
| 495 |
atmVplCrossConnectIdentifier values for the two VPLs, and the cross- |
| 496 |
|
| 497 |
|
| 498 |
|
| 499 |
|
| 500 |
<span class="grey">Tesink Standards Track [Page 9]</span></pre> |
| 501 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-10" ></span> |
| 502 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 503 |
|
| 504 |
|
| 505 |
rconnect between two VCLs is represented in the |
| 506 |
atmVcCrossConnectTable of the ATM-MIB, indexed by the |
| 507 |
atmVclCrossConnectIdentifier values for the two VCLs. |
| 508 |
|
| 509 |
For an SVC or Soft PVC the VPL and VCL tables defined in this memo |
| 510 |
are used. Hoewever, for an SVC or Soft PVC the cross-connect between |
| 511 |
two VPLs is represented in the atmSvcVpCrossConnectTable of the |
| 512 |
ATM2-MIB, indexed by the atmVplCrossConnectIdentifier values for the |
| 513 |
two VPLs, and the cross-connect between two VCLs is represented in |
| 514 |
the atmSvcVcCrossConnectTable of the ATM2-MIB, indexed by the |
| 515 |
atmVclCrossConnectIdentifier values for the two VCLs. |
| 516 |
|
| 517 |
Note: The ATM2-MIB module was being defined in a separate memo at the |
| 518 |
time of this publication. Please consult the RFC directory for an |
| 519 |
exact reference. |
| 520 |
|
| 521 |
<span class="h2"><a class="selflink" id="section-5" href="#section-5">5</a>. Application of MIB II to ATM</span> |
| 522 |
|
| 523 |
<span class="h3"><a class="selflink" id="section-5.1" href="#section-5.1">5.1</a>. The System Group</span> |
| 524 |
|
| 525 |
For the purposes of the sysServices object in the System Group of MIB |
| 526 |
II [<a href="#ref-16" title=""Management Information Base for Network Management of TCP/IP-based internets: MIB-II"">16</a>], ATM is a data link layer protocol. Thus, for ATM switches |
| 527 |
and ATM networks, sysServices will have the value "2". |
| 528 |
|
| 529 |
<span class="h3"><a class="selflink" id="section-5.2" href="#section-5.2">5.2</a>. The Interface Group</span> |
| 530 |
|
| 531 |
The Interfaces Group of MIB II defines generic managed objects for |
| 532 |
managing interfaces. This memo contains the media-specific |
| 533 |
extensions to the Interfaces Group for managing ATM interfaces. |
| 534 |
|
| 535 |
This memo assumes the interpretation of the Interfaces Group to be in |
| 536 |
accordance with [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>] which states that the interfaces table (ifTable) |
| 537 |
contains information on the managed resource's interfaces and that |
| 538 |
each sub-layer below the internetwork layer of a network interface is |
| 539 |
considered an interface. Thus, the ATM cell layer interface is |
| 540 |
represented as an entry in the ifTable. This entry is concerned with |
| 541 |
the ATM cell layer as a whole, and not with individual virtual |
| 542 |
connections which are managed via the ATM-specific managed objects |
| 543 |
specified in this memo. The inter-relation of entries in the ifTable |
| 544 |
is defined by Interfaces Stack Group defined in [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>]. |
| 545 |
|
| 546 |
<span class="h4"><a class="selflink" id="section-5.2.1" href="#section-5.2.1">5.2.1</a>. Support of the ATM Cell Layer by ifTable</span> |
| 547 |
|
| 548 |
Some specific interpretations of ifTable for the ATM cell layer |
| 549 |
follow. |
| 550 |
|
| 551 |
|
| 552 |
|
| 553 |
|
| 554 |
|
| 555 |
|
| 556 |
<span class="grey">Tesink Standards Track [Page 10]</span></pre> |
| 557 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-11" ></span> |
| 558 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 559 |
|
| 560 |
|
| 561 |
Object Use for the generic ATM layer |
| 562 |
====== ============================= |
| 563 |
|
| 564 |
ifIndex Each ATM port is represented by an ifEntry. |
| 565 |
|
| 566 |
ifDescr Description of the ATM interface. |
| 567 |
|
| 568 |
ifType The value that is allocated for ATM is 37. |
| 569 |
|
| 570 |
ifSpeed The total bandwidth in bits per second |
| 571 |
for use by the ATM layer. |
| 572 |
|
| 573 |
ifPhysAddress The interface's address at the ATM protocol |
| 574 |
sublayer; the ATM address which would be used as the value |
| 575 |
of the Called Party Address Information Element (IE) of a |
| 576 |
signalling message for a connection which either: |
| 577 |
- would terminate at this interface, or |
| 578 |
- for which the Called Party Address IE |
| 579 |
would need to be replaced by the Called Party SubAddress |
| 580 |
IE before the message was forwarded to any other |
| 581 |
interface. |
| 582 |
For an interface on which signalling is not supported, |
| 583 |
then the interface does not necessarily have an address, |
| 584 |
but if it does, then ifPhysAddress is the address which |
| 585 |
would be used as above in the event that signalling were |
| 586 |
supported. If the interface has multiple such addresses, |
| 587 |
then ifPhysAddress is its primary address. If the |
| 588 |
interface has no addresses, then ifPhysAddress is an octet |
| 589 |
string of zero length. Address encoding is as per [<a href="#ref-20" title="ATM User-Network Interface">20</a>]. |
| 590 |
Note that addresses assigned for purposes other than those |
| 591 |
listed above (e.g., an address associated with the service |
| 592 |
provider side of a public network UNI) may be represented |
| 593 |
through atmInterfaceSubscrAddress. |
| 594 |
|
| 595 |
ifAdminStatus See [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>]. |
| 596 |
|
| 597 |
ifOperStatus Assumes the value down(2) if the ATM cell |
| 598 |
layer is down. |
| 599 |
|
| 600 |
ifLastChange See [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>]. |
| 601 |
|
| 602 |
ifInOctets The number of received octets over the |
| 603 |
interface, i.e., the number of received, assigned cells |
| 604 |
multiplied by 53. |
| 605 |
|
| 606 |
ifOutOctets The number of transmitted octets over the interface, |
| 607 |
i.e., the number of transmitted, assigned cells multiplied |
| 608 |
by 53. |
| 609 |
|
| 610 |
|
| 611 |
|
| 612 |
<span class="grey">Tesink Standards Track [Page 11]</span></pre> |
| 613 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-12" ></span> |
| 614 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 615 |
|
| 616 |
|
| 617 |
ifInErrors The number of cells dropped due to uncorrectable HEC |
| 618 |
errors. |
| 619 |
|
| 620 |
ifInUnknownProtos The number of received cells discarded during cell |
| 621 |
header validation, including cells with unrecognized |
| 622 |
VPI/VCI values, and cells with invalid cell header |
| 623 |
patterns. If cells with undefined PTI values are |
| 624 |
discarded, they are also counted here. |
| 625 |
|
| 626 |
ifOutErrors See [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>]. |
| 627 |
|
| 628 |
ifName Textual name (unique on this system) of the |
| 629 |
interface or an octet string of zero length. |
| 630 |
|
| 631 |
ifLinkUpDownTrapEnable Default is disabled (2). |
| 632 |
|
| 633 |
ifConnectorPresent Set to false (2). |
| 634 |
|
| 635 |
ifHighSpeed See [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>]. |
| 636 |
|
| 637 |
ifHCInOctets The 64-bit version of ifInOctets; supported |
| 638 |
if required by the compliance statements in [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>]. |
| 639 |
|
| 640 |
ifHCOutOctets The 64-bit version of ifOutOctets; supported |
| 641 |
if required by the compliance statements in [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>]. |
| 642 |
|
| 643 |
ifAlias The non-volatile 'alias' name for the interface |
| 644 |
as specified by a network manager. |
| 645 |
|
| 646 |
<span class="h2"><a class="selflink" id="section-6" href="#section-6">6</a>. Support of the AAL3/4 Based Interfaces</span> |
| 647 |
|
| 648 |
For the management of AAL3/4 CPCS layer, see [<a href="#ref-18" title=""Definitions of Managed Objects for SMDS Interfaces"">18</a>]. |
| 649 |
|
| 650 |
<span class="h2"><a class="selflink" id="section-7" href="#section-7">7</a>. Support of the AAL5 Managed Objects</span> |
| 651 |
|
| 652 |
Support of AAL5 managed objects in an ATM switch and ATM host are |
| 653 |
described below. |
| 654 |
|
| 655 |
<span class="h3"><a class="selflink" id="section-7.1" href="#section-7.1">7.1</a>. Managing AAL5 in a Switch</span> |
| 656 |
|
| 657 |
Managing AAL5 in a switch involves: |
| 658 |
|
| 659 |
(1) performance management of an AAL5 entity as |
| 660 |
an internal resource in a switch |
| 661 |
|
| 662 |
(2) performance management of AAL5 per virtual connection |
| 663 |
|
| 664 |
|
| 665 |
|
| 666 |
|
| 667 |
|
| 668 |
<span class="grey">Tesink Standards Track [Page 12]</span></pre> |
| 669 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-13" ></span> |
| 670 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 671 |
|
| 672 |
|
| 673 |
AAL5 in a switch is modeled as shown in Figure 7 and 8. AAL5 will be |
| 674 |
managed in a switch for only those virtual connections that carry |
| 675 |
AAL5 and are terminated at the AAL5 entity in the switch. Note that, |
| 676 |
the virtual channels within the ATM UNIs carrying AAL5 will be |
| 677 |
switched by the ATM switching fabric (termed as ATM Entity in the |
| 678 |
figure) to the virtual channels on a proprietary internal interface |
| 679 |
associated with the AAL5 process (termed as AAL5 Entity in the |
| 680 |
figure). Therefore, performance management of the AAL5 resource in |
| 681 |
the switch will be modeled using the ifTable through an internal |
| 682 |
(pseudo-ATM) virtual interface and the AAL5 performance management |
| 683 |
per virtual connection will be supported using an additional AAL5 |
| 684 |
connection table in the ATM MIB. The association between the AAL5 |
| 685 |
virtual link at the proprietary virtual, internal interface and the |
| 686 |
ATM virtual link at the ATM interface will be derived from the |
| 687 |
virtual channel cross-connect table and the virtual channel link |
| 688 |
table in the ATM MIB. Note that for the proprietary virtual interface |
| 689 |
the traffic transmit and receive conventions in the virtual channel |
| 690 |
link table are as follows: |
| 691 |
|
| 692 |
Transmitting traffic: ATM Entity ---> AAL5 Entity |
| 693 |
Receiving traffic: ATM Entity <--- AAL5 Entity |
| 694 |
|
| 695 |
___________________________ |
| 696 |
| | |
| 697 |
| ============= | |
| 698 |
| | AAL5 | | |
| 699 |
| | Entity | | |
| 700 |
| ============= | |
| 701 |
| | | |
| 702 |
| -----Prop. Virtual Interface |
| 703 |
| | | |
| 704 |
| ============= | |
| 705 |
| | ATM | | |
| 706 |
| | Entity | | |
| 707 |
| ============= | |
| 708 |
|_____|__|__|__|__|_______| |
| 709 |
| | | | | |
| 710 |
---------------- ATM UNIs |
| 711 |
| | | | | |
| 712 |
| | | | | |
| 713 |
v v v v v |
| 714 |
|
| 715 |
Figure 7: Model of an AAL5 Entity in a Switch |
| 716 |
|
| 717 |
|
| 718 |
|
| 719 |
|
| 720 |
|
| 721 |
|
| 722 |
|
| 723 |
|
| 724 |
<span class="grey">Tesink Standards Track [Page 13]</span></pre> |
| 725 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-14" ></span> |
| 726 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 727 |
|
| 728 |
|
| 729 |
__________________ |
| 730 |
| | |
| 731 |
| AAL5 | |
| 732 |
|________________| |
| 733 |
| | |
| 734 |
| Prop. Virtual | |
| 735 |
| Interface | |
| 736 |
|________________| |
| 737 |
|
| 738 |
Figure 8: AAL5 Entity's Interface Stack in a Switch |
| 739 |
|
| 740 |
<span class="h3"><a class="selflink" id="section-7.2" href="#section-7.2">7.2</a>. Managing AAL5 in a Host</span> |
| 741 |
|
| 742 |
Managing AAL5 in a host involves managing the AAL5 sublayer interface |
| 743 |
as shown in Figure 9 and 10. The AAL5 sublayer is stacked directly |
| 744 |
over the ATM sublayer. The ifTable is applied to the AAL5 sublayer |
| 745 |
as defined in <a href="#section-10.3">Section 10.3</a>. |
| 746 |
|
| 747 |
___________________________ |
| 748 |
| | |
| 749 |
| ============= | |
| 750 |
| | AAL5 | | |
| 751 |
| | Entity | | |
| 752 |
| ============= | |
| 753 |
| | ATM | | |
| 754 |
| | Entity | | |
| 755 |
| ============= | |
| 756 |
|___________|_____________| |
| 757 |
| |
| 758 |
__|__ ATM UNI |
| 759 |
| |
| 760 |
| |
| 761 |
v |
| 762 |
|
| 763 |
Figure 9: Model of an AAL5 Entity in a Host |
| 764 |
|
| 765 |
__________________ |
| 766 |
| | |
| 767 |
| AAL5 | |
| 768 |
|________________| |
| 769 |
| | |
| 770 |
| ATM Layer | |
| 771 |
|________________| |
| 772 |
| | |
| 773 |
| Physical Layer| |
| 774 |
|________________| |
| 775 |
|
| 776 |
Figure 10: AAL5 Entity's Interface Stack in a Host |
| 777 |
|
| 778 |
|
| 779 |
|
| 780 |
<span class="grey">Tesink Standards Track [Page 14]</span></pre> |
| 781 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-15" ></span> |
| 782 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 783 |
|
| 784 |
|
| 785 |
<span class="h3"><a class="selflink" id="section-7.3" href="#section-7.3">7.3</a>. Support of AAL5 by ifTable</span> |
| 786 |
|
| 787 |
The AAL5 entity in an ATM device (e.g., switch or host) is managed |
| 788 |
using the ifTable. There are additional counters specified for AAL5 |
| 789 |
than those specified in the ATM B-ICI document [<a href="#ref-21" title="af-bici-0013.002">21</a>]. Specific |
| 790 |
interpretations of ifTable for the AAL5 CPCS layer are as follows. |
| 791 |
|
| 792 |
Object Use for AAL5 CPCS layer entity |
| 793 |
====== ============================== |
| 794 |
|
| 795 |
ifIndex Each AAL5 entity is represented by an ifEntry. |
| 796 |
|
| 797 |
ifDescr Description of the AAL5 entity. |
| 798 |
|
| 799 |
ifType The value that is allocated for AAL5 is 49. |
| 800 |
|
| 801 |
ifMtu Set to the largest PDU size for the |
| 802 |
AAL5 CPCS layer that can be processed |
| 803 |
by the AAL5 entity. |
| 804 |
|
| 805 |
ifSpeed Set to 0. |
| 806 |
|
| 807 |
ifPhysAddress An octet string of zero length. |
| 808 |
|
| 809 |
ifAdminStatus See [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>]. |
| 810 |
|
| 811 |
ifOperStatus Assumes the value down(2) if the AAL5 |
| 812 |
layer is down. |
| 813 |
|
| 814 |
ifLastChange See [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>]. |
| 815 |
|
| 816 |
ifInOctets The number of received AAL5 CPCS PDU octets. |
| 817 |
|
| 818 |
ifOutOctets The number of AAL5 CPCS PDU octets |
| 819 |
transmitted. |
| 820 |
|
| 821 |
ifInUcastPkts The number of received AAL5 CPCS PDUs passed |
| 822 |
to a higher-layer. |
| 823 |
|
| 824 |
ifOutUcastPkts The number of AAL5 CPCS PDUs received from a |
| 825 |
higher-layer for transmission. |
| 826 |
[Note: The number of AAL5 PDUs actually |
| 827 |
transmitted is the number received from a |
| 828 |
higher-layer for transmission minus any which |
| 829 |
are counted by ifOutErrors and ifOutDiscards.] |
| 830 |
|
| 831 |
|
| 832 |
|
| 833 |
|
| 834 |
|
| 835 |
|
| 836 |
<span class="grey">Tesink Standards Track [Page 15]</span></pre> |
| 837 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-16" ></span> |
| 838 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 839 |
|
| 840 |
|
| 841 |
ifInErrors Number of errored AAL5 CPCS PDUs received. |
| 842 |
The types of errors counted include CRC-32 errors, |
| 843 |
SAR time-out errors, and oversized SDU errors. |
| 844 |
|
| 845 |
ifInUnknownProtos Set to 0. |
| 846 |
|
| 847 |
ifInDiscards Number of received AAL5 CPCS PDUs discarded. |
| 848 |
Possible reason may be input buffer overflow. |
| 849 |
|
| 850 |
ifOutErrors Number of AAL5 CPCS PDUs that could not |
| 851 |
be transmitted due to errors. |
| 852 |
|
| 853 |
ifOutDiscards Number of AAL5 CPCS PDUs received for |
| 854 |
transmission that are discarded. |
| 855 |
Possible reason may be output buffer |
| 856 |
overflow. |
| 857 |
|
| 858 |
ifInMulticastPkts Set to 0. |
| 859 |
|
| 860 |
ifInBroadcastPkts Set to 0. |
| 861 |
|
| 862 |
ifOutMulticastPkts Set to 0. |
| 863 |
|
| 864 |
ifOutBroadcastPkts Set to 0. |
| 865 |
|
| 866 |
ifName Textual name (unique on this system) of the |
| 867 |
AAL5 entity or an octet string of zero length. |
| 868 |
|
| 869 |
ifHighSpeed Set to 0. |
| 870 |
|
| 871 |
ifConnectorPresent Set to false (2). |
| 872 |
|
| 873 |
ifPromiscuousMode Set to false(2). |
| 874 |
|
| 875 |
ifLinkUpDownTrapEnable Default is disabled (2). |
| 876 |
|
| 877 |
ifAlias The non-volatile 'alias' name for the interface |
| 878 |
as specified by a network manager. |
| 879 |
|
| 880 |
<span class="h3"><a class="selflink" id="section-7.4" href="#section-7.4">7.4</a>. Support of Proprietary Virtual Interface by ifTable</span> |
| 881 |
|
| 882 |
Specific interpretations of ifTable for the proprietary virtual, |
| 883 |
internal interface associated with an AAL5 entity in an ATM switch |
| 884 |
are as follows. |
| 885 |
|
| 886 |
|
| 887 |
|
| 888 |
|
| 889 |
|
| 890 |
|
| 891 |
|
| 892 |
<span class="grey">Tesink Standards Track [Page 16]</span></pre> |
| 893 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-17" ></span> |
| 894 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 895 |
|
| 896 |
|
| 897 |
Object Use for proprietary virtual, internal interface |
| 898 |
associated with AAL entities |
| 899 |
====== =============================================== |
| 900 |
|
| 901 |
ifIndex Each proprietary virtual, internal interface |
| 902 |
associated with AAL entities is represented by an |
| 903 |
ifEntry. |
| 904 |
|
| 905 |
ifDescr Description of the proprietary virtual, internal |
| 906 |
interface associated with AAL entities. |
| 907 |
|
| 908 |
ifType The value that is allocated for proprietary |
| 909 |
virtual, internal interface is 53. |
| 910 |
|
| 911 |
ifSpeed See [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>]. Set to 0 if the speed is not |
| 912 |
known. |
| 913 |
|
| 914 |
ifPhysAddress See [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>]. An octet string of zero length |
| 915 |
if no address is used for this interface. |
| 916 |
|
| 917 |
ifAdminStatus See [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>]. |
| 918 |
|
| 919 |
ifOperStatus See [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>]. |
| 920 |
|
| 921 |
ifLastChange See [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>]. |
| 922 |
|
| 923 |
ifName Textual name (unique on this system) of the |
| 924 |
interface or an octet string of zero length. |
| 925 |
|
| 926 |
ifHighSpeed See [<a href="#ref-17" title=""The Interfaces Group MIB"">17</a>]. Set to 0 if the speed is not known. |
| 927 |
|
| 928 |
ifConnectorPresent Set to false (2). |
| 929 |
|
| 930 |
ifLinkUpDownTrapEnable Default is disabled (2). |
| 931 |
|
| 932 |
ifAlias The non-volatile 'alias' name for the interface |
| 933 |
as specified by a network manager. |
| 934 |
|
| 935 |
<span class="h3"><a class="selflink" id="section-7.5" href="#section-7.5">7.5</a>. AAL5 Connection Performance Statistics Table</span> |
| 936 |
|
| 937 |
An AAL5 connection table is used to provide AAL5 performance |
| 938 |
information for each AAL5 virtual connection that is terminated at |
| 939 |
the AAL5 entity contained within an ATM switch or host. |
| 940 |
|
| 941 |
|
| 942 |
|
| 943 |
|
| 944 |
|
| 945 |
|
| 946 |
|
| 947 |
|
| 948 |
<span class="grey">Tesink Standards Track [Page 17]</span></pre> |
| 949 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-18" ></span> |
| 950 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 951 |
|
| 952 |
|
| 953 |
<span class="h2"><a class="selflink" id="section-8" href="#section-8">8</a>. ILMI MIBs and the ATM Managed Objects</span> |
| 954 |
|
| 955 |
The ILMI MIBs are specified by the ATM Forum as a set of several |
| 956 |
MIBs, all currently defined in the ILMI Specification [<a href="#ref-23" title=""ATM Forum Integrated Local Management Interface (ILMI) Specification"">23</a>]. The ILMI |
| 957 |
protocols and MIBs allow two connected ATM Interface Management |
| 958 |
Entities (IMEs) to exchange bi-directional parameters, mainly to |
| 959 |
facilitate auto-configuration between ATM peer entities. The support |
| 960 |
of the ATM management functions by the ILMI MIBs and those contained |
| 961 |
in this memo are compared in Table 1. In this table, "yes" in the |
| 962 |
"ILMI MIBs" column indicates that the management functions are |
| 963 |
supported by the ILMI MIBs. The parenthesized numbers in the "This |
| 964 |
memo" column correspond to the sets of tables enumerated in <a href="#section-6.2">Section</a> |
| 965 |
<a href="#section-6.2">6.2</a>. |
| 966 |
|
| 967 |
For that subset of management information which the ILMI MIBs and |
| 968 |
this memo have in common, every effort has been made to retain |
| 969 |
identical semantics and syntax, even though the MIB objects are |
| 970 |
identified using different OBJECT IDENTIFIERs. |
| 971 |
|
| 972 |
Table 1 - Structuring of ATM Managed Objects |
| 973 |
______________________________________________________________ |
| 974 |
| |This |ILMI| |
| 975 |
ATM Mgmt.Inf. |ATM Managed Objects |memo |MIBs| |
| 976 |
______________|_________________________________|_______|____| |
| 977 |
|
| 978 |
Local Interface Information: |
| 979 |
_____________________________________________________________ |
| 980 |
ATM interface:| (1) port identifier |ATM MIB| | |
| 981 |
physical layer| (2) physical transmission types | (1)*|yes | |
| 982 |
configuration | (3) operational status |MIB II | * | |
| 983 |
| (4) administrative status | | ** | |
| 984 |
| (5) last change status | | | |
| 985 |
_____________________________________________________________ |
| 986 |
ATM interface:| (1) active VPI/VCI fields |ATM MIB| | |
| 987 |
cell layer | (2) maximum number of VPCs/VCCs | (1) |yes | |
| 988 |
configuration | (3) configured VPCs/VCCs | | ** | |
| 989 |
| (4) ILMI VPI/VCI values | | | |
| 990 |
| (5) Neighbor system info | | | |
| 991 |
| (6) Max. number of VPI/VCI bits | |yes | |
| 992 |
| (7) ATM Subscribed Address | | | |
| 993 |
_____________________________________________________________ |
| 994 |
ATM interface:|(1) received/transmitted cells | | | |
| 995 |
cell layer |(2) cells with HEC error |MIB II |yes | |
| 996 |
performance |(3) cell header validation errors| | | |
| 997 |
_____________________________________________________________ |
| 998 |
|
| 999 |
|
| 1000 |
|
| 1001 |
|
| 1002 |
|
| 1003 |
|
| 1004 |
<span class="grey">Tesink Standards Track [Page 18]</span></pre> |
| 1005 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-19" ></span> |
| 1006 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1007 |
|
| 1008 |
|
| 1009 |
_____________________________________________________________ |
| 1010 |
ATM interface:|(1)DS3 PLCP severely errored |ATM MIB| | |
| 1011 |
PLCP & TC | framing seconds | (2)| | |
| 1012 |
layer |(2)DS3 PLCP unavailable seconds | |no | |
| 1013 |
performance |(3)DS3 PLCP alarm state | | | |
| 1014 |
|(4)out of cell delineation events| | | |
| 1015 |
|(5)TC alarm state | | | |
| 1016 |
_____________________________________________________________ |
| 1017 |
VP/VC link: |(1)VPI or VPI/VCI value |ATM MIB| | |
| 1018 |
configuration |(2)VCL or VPL operational status | (3,4)|yes | |
| 1019 |
|(3)VCL/VPL administrative status | |*** | |
| 1020 |
|(4)VCL/VPL last change status | | | |
| 1021 |
|(5)transmit/receive traffic/ | | | |
| 1022 |
| service category parameters | | | |
| 1023 |
|(6)AAL type | | | |
| 1024 |
|(7)transmit/receive AAL5 SDU size| | | |
| 1025 |
|(8)AAL5 encapsulation type | | | |
| 1026 |
|(9)connection topology type | | | |
| 1027 |
|(10)use of call control | | | |
| 1028 |
_____________________________________________________________ |
| 1029 |
VP/VC |(1)cross-connect identifier | | | |
| 1030 |
Cross-connect:|(2)port identifier of one | | | |
| 1031 |
configuration | end | | | |
| 1032 |
|(3)port identifier of the other |ATM MIB| | |
| 1033 |
| end | (5)|no | |
| 1034 |
|(4)VPI or VPI/VCI value | | | |
| 1035 |
| of one end | | | |
| 1036 |
|(5)VPI or VPI/VCI value of | | | |
| 1037 |
| the other end | | | |
| 1038 |
|(6)VC/VP cross-connect | | | |
| 1039 |
| operational status | | | |
| 1040 |
|(7)VC/VP cross-connect | | | |
| 1041 |
| administrative status | | | |
| 1042 |
|(8)VC/VP last change status | | | |
| 1043 |
_____________________________________________________________ |
| 1044 |
VCC AAL5 CPCS |(1)PDUs discarded for CRC errors |ATM MIB| | |
| 1045 |
layer: |(2)PDUs discarded due to | (6) | | |
| 1046 |
performance | reassembly time out | |no | |
| 1047 |
|(3)PDUs discarded due to large | | | |
| 1048 |
| SDUs | | | |
| 1049 |
_____________________________________________________________ |
| 1050 |
AAL5 entity: |(1)received/transmitted PDUs | | | |
| 1051 |
|(2)PDUs discarded due to | | | |
| 1052 |
| protocol errors |MIB II |no | |
| 1053 |
|(3)a set of configuration/state | | | |
| 1054 |
| parameters | | | |
| 1055 |
_____________________________________________________________ |
| 1056 |
|
| 1057 |
|
| 1058 |
|
| 1059 |
|
| 1060 |
<span class="grey">Tesink Standards Track [Page 19]</span></pre> |
| 1061 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-20" ></span> |
| 1062 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1063 |
|
| 1064 |
|
| 1065 |
*The operational, administrative, and last change status of the ATM |
| 1066 |
interface and the physical transmission type shall be supported by |
| 1067 |
the interface table in MIB II [<a href="#ref-16" title=""Management Information Base for Network Management of TCP/IP-based internets: MIB-II"">16</a>][17]. ILMI does not contain the |
| 1068 |
administrative and last change status of the ATM interface. |
| 1069 |
|
| 1070 |
** The ILMI MIB contains read-only objects for various parameters at |
| 1071 |
the ATM interface level. |
| 1072 |
|
| 1073 |
***The ILMI MIBs contain local and end-to-end operational status of |
| 1074 |
the VPC/VCC segment. However, it does not contain the VPC/VCC |
| 1075 |
administrative and last change status and the VCC AAL information. |
| 1076 |
|
| 1077 |
<span class="h2"><a class="selflink" id="section-9" href="#section-9">9</a>. Definitions</span> |
| 1078 |
|
| 1079 |
ATM-MIB DEFINITIONS ::= BEGIN |
| 1080 |
|
| 1081 |
IMPORTS |
| 1082 |
MODULE-IDENTITY, OBJECT-TYPE, |
| 1083 |
Counter32, Integer32, IpAddress, mib-2 |
| 1084 |
FROM SNMPv2-SMI |
| 1085 |
DisplayString, RowStatus, TruthValue |
| 1086 |
FROM SNMPv2-TC |
| 1087 |
MODULE-COMPLIANCE, OBJECT-GROUP |
| 1088 |
FROM SNMPv2-CONF |
| 1089 |
InterfaceIndex, ifIndex |
| 1090 |
FROM IF-MIB |
| 1091 |
AtmAddr, AtmConnKind, AtmConnCastType, |
| 1092 |
AtmServiceCategory, AtmTrafficDescrParamIndex, |
| 1093 |
AtmVpIdentifier, AtmVcIdentifier, |
| 1094 |
AtmVorXAdminStatus, AtmVorXLastChange, |
| 1095 |
AtmVorXOperStatus, atmNoClpNoScr |
| 1096 |
FROM ATM-TC-MIB; |
| 1097 |
|
| 1098 |
|
| 1099 |
atmMIB MODULE-IDENTITY |
| 1100 |
LAST-UPDATED "9810191200Z" |
| 1101 |
ORGANIZATION "IETF AToM MIB Working Group" |
| 1102 |
CONTACT-INFO |
| 1103 |
" Kaj Tesink |
| 1104 |
Postal: Bellcore |
| 1105 |
331 Newman Springs Road |
| 1106 |
Red Bank, NJ 07701 |
| 1107 |
Tel: 732-758-5254 |
| 1108 |
Fax: 732-758-2269 |
| 1109 |
E-mail: [email protected]" |
| 1110 |
DESCRIPTION |
| 1111 |
"This is the MIB Module for ATM and AAL5-related |
| 1112 |
objects for managing ATM interfaces, ATM virtual |
| 1113 |
|
| 1114 |
|
| 1115 |
|
| 1116 |
<span class="grey">Tesink Standards Track [Page 20]</span></pre> |
| 1117 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-21" ></span> |
| 1118 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1119 |
|
| 1120 |
|
| 1121 |
links, ATM cross-connects, AAL5 entities, and |
| 1122 |
and AAL5 connections." |
| 1123 |
REVISION "9810191200Z" |
| 1124 |
DESCRIPTION |
| 1125 |
"The initial revision of this module was published |
| 1126 |
as <a href="./rfc1695">RFC 1695</a>. Key revisions include: |
| 1127 |
o Textual Conventions and OBJECT IDENTITIES have |
| 1128 |
been moved to a separate MIB module. |
| 1129 |
o Applicability of objects to PVCs, SVCs and Soft |
| 1130 |
PVCs has been clarified. |
| 1131 |
o DEFVAL clauses have been added. |
| 1132 |
o The relationship of ifIndex values with different |
| 1133 |
layers and sublayers related to ATM has been |
| 1134 |
clarified. |
| 1135 |
o atmTrafficQosClass has been deprecated |
| 1136 |
and replaced with atmServiceCategory. |
| 1137 |
o atmInterfaceCurrentMaxVpiBits and |
| 1138 |
atmInterfaceCurrentMaxVciBits have been added with |
| 1139 |
a description on their relationship with other |
| 1140 |
objects. |
| 1141 |
o atmInterfaceAddressType and atmInterfaceAdminAddress |
| 1142 |
have been deprecated and replaced by |
| 1143 |
atmInterfaceSubscrAddress. |
| 1144 |
o atmInterfaceTCAlarmState has been clarified. |
| 1145 |
o atmTrafficDescrParamIndexNext has been introduced |
| 1146 |
in order to provide a manager a free |
| 1147 |
atmTrafficDescrParamIndex value. |
| 1148 |
o The atmTrafficFrameDiscard capability has been added. |
| 1149 |
o A connection topology type (atmVpl/VclCastType) and |
| 1150 |
a call control type (atmVpl/VclConnKind) have been |
| 1151 |
added. |
| 1152 |
o aal2 has been added to atmVccAalType." |
| 1153 |
REVISION "9406072245Z" |
| 1154 |
DESCRIPTION |
| 1155 |
"The <a href="./rfc1695">RFC1695</a> version of this MIB module." |
| 1156 |
::= { mib-2 37 } |
| 1157 |
|
| 1158 |
|
| 1159 |
atmMIBObjects OBJECT IDENTIFIER ::= {atmMIB 1} |
| 1160 |
|
| 1161 |
-- {atmMIBObjects 1} has been moved to a separate |
| 1162 |
-- specification [<a href="#ref-19" title=""Definitions of Textual Conventions and OBJECT-IDENTITIES for ATM Management"">19</a>]. |
| 1163 |
|
| 1164 |
|
| 1165 |
-- This ATM MIB Module consists of the following tables: |
| 1166 |
-- (1) ATM Interface configuration table |
| 1167 |
-- (2) ATM Interface DS3 PLCP table |
| 1168 |
-- (3) ATM Interface TC Sublayer table |
| 1169 |
|
| 1170 |
|
| 1171 |
|
| 1172 |
<span class="grey">Tesink Standards Track [Page 21]</span></pre> |
| 1173 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-22" ></span> |
| 1174 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1175 |
|
| 1176 |
|
| 1177 |
-- (4) Atm Traffic Descriptor table |
| 1178 |
-- (5) ATM Interface VPL configuration table |
| 1179 |
-- (6) ATM Interface VCL configuration table |
| 1180 |
-- (7) ATM VP Cross Connect table (for PVCs) |
| 1181 |
-- (8) ATM VC Cross Connect table (for PVCs) |
| 1182 |
-- (9) ATM Interface AAL5 VCC performance statistics |
| 1183 |
-- table |
| 1184 |
|
| 1185 |
-- ATM Interface Configuration Parameters Table |
| 1186 |
|
| 1187 |
-- This table contains ATM specific |
| 1188 |
-- configuration information associated with |
| 1189 |
-- an ATM interface beyond those |
| 1190 |
-- supported using the ifTable. |
| 1191 |
|
| 1192 |
|
| 1193 |
|
| 1194 |
|
| 1195 |
atmInterfaceConfTable OBJECT-TYPE |
| 1196 |
SYNTAX SEQUENCE OF AtmInterfaceConfEntry |
| 1197 |
MAX-ACCESS not-accessible |
| 1198 |
STATUS current |
| 1199 |
DESCRIPTION |
| 1200 |
"This table contains ATM local interface |
| 1201 |
configuration parameters, one entry per ATM |
| 1202 |
interface port." |
| 1203 |
::= { atmMIBObjects 2 } |
| 1204 |
|
| 1205 |
atmInterfaceConfEntry OBJECT-TYPE |
| 1206 |
SYNTAX AtmInterfaceConfEntry |
| 1207 |
MAX-ACCESS not-accessible |
| 1208 |
STATUS current |
| 1209 |
DESCRIPTION |
| 1210 |
"This list contains ATM interface configuration |
| 1211 |
parameters and state variables and is indexed |
| 1212 |
by ifIndex values of ATM interfaces." |
| 1213 |
INDEX { ifIndex } |
| 1214 |
::= { atmInterfaceConfTable 1} |
| 1215 |
|
| 1216 |
AtmInterfaceConfEntry ::= SEQUENCE { |
| 1217 |
atmInterfaceMaxVpcs INTEGER, |
| 1218 |
atmInterfaceMaxVccs INTEGER, |
| 1219 |
atmInterfaceConfVpcs INTEGER, |
| 1220 |
atmInterfaceConfVccs INTEGER, |
| 1221 |
atmInterfaceMaxActiveVpiBits INTEGER, |
| 1222 |
atmInterfaceMaxActiveVciBits INTEGER, |
| 1223 |
atmInterfaceIlmiVpi AtmVpIdentifier, |
| 1224 |
atmInterfaceIlmiVci AtmVcIdentifier, |
| 1225 |
|
| 1226 |
|
| 1227 |
|
| 1228 |
<span class="grey">Tesink Standards Track [Page 22]</span></pre> |
| 1229 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-23" ></span> |
| 1230 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1231 |
|
| 1232 |
|
| 1233 |
atmInterfaceAddressType INTEGER, |
| 1234 |
atmInterfaceAdminAddress AtmAddr, |
| 1235 |
atmInterfaceMyNeighborIpAddress IpAddress, |
| 1236 |
atmInterfaceMyNeighborIfName DisplayString, |
| 1237 |
atmInterfaceCurrentMaxVpiBits INTEGER, |
| 1238 |
atmInterfaceCurrentMaxVciBits INTEGER, |
| 1239 |
atmInterfaceSubscrAddress AtmAddr |
| 1240 |
} |
| 1241 |
|
| 1242 |
|
| 1243 |
atmInterfaceMaxVpcs OBJECT-TYPE |
| 1244 |
SYNTAX INTEGER (0..4096) |
| 1245 |
MAX-ACCESS read-write |
| 1246 |
STATUS current |
| 1247 |
DESCRIPTION |
| 1248 |
"The maximum number of VPCs (PVPCs and SVPCs) |
| 1249 |
supported at this ATM interface. At the ATM UNI, |
| 1250 |
the maximum number of VPCs (PVPCs and SVPCs) |
| 1251 |
ranges from 0 to 256 only." |
| 1252 |
::= { atmInterfaceConfEntry 1} |
| 1253 |
|
| 1254 |
atmInterfaceMaxVccs OBJECT-TYPE |
| 1255 |
SYNTAX INTEGER (0..65536) |
| 1256 |
MAX-ACCESS read-write |
| 1257 |
STATUS current |
| 1258 |
DESCRIPTION |
| 1259 |
"The maximum number of VCCs (PVCCs and SVCCs) |
| 1260 |
supported at this ATM interface." |
| 1261 |
::= { atmInterfaceConfEntry 2} |
| 1262 |
|
| 1263 |
atmInterfaceConfVpcs OBJECT-TYPE |
| 1264 |
SYNTAX INTEGER (0..4096) |
| 1265 |
MAX-ACCESS read-only |
| 1266 |
STATUS current |
| 1267 |
DESCRIPTION |
| 1268 |
"The number of VPCs (PVPC, Soft PVPC and SVPC) |
| 1269 |
currently in use at this ATM interface. It includes |
| 1270 |
the number of PVPCs and Soft PVPCs that are configured |
| 1271 |
at the interface, plus the number of SVPCs |
| 1272 |
that are currently established at the |
| 1273 |
interface. |
| 1274 |
|
| 1275 |
At the ATM UNI, the configured number of |
| 1276 |
VPCs (PVPCs and SVPCs) can range from |
| 1277 |
0 to 256 only." |
| 1278 |
::= { atmInterfaceConfEntry 3} |
| 1279 |
|
| 1280 |
atmInterfaceConfVccs OBJECT-TYPE |
| 1281 |
|
| 1282 |
|
| 1283 |
|
| 1284 |
<span class="grey">Tesink Standards Track [Page 23]</span></pre> |
| 1285 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-24" ></span> |
| 1286 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1287 |
|
| 1288 |
|
| 1289 |
SYNTAX INTEGER (0..65536) |
| 1290 |
MAX-ACCESS read-only |
| 1291 |
STATUS current |
| 1292 |
DESCRIPTION |
| 1293 |
"The number of VCCs (PVCC, Soft PVCC and SVCC) |
| 1294 |
currently in use at this ATM interface. It includes |
| 1295 |
the number of PVCCs and Soft PVCCs that are configured |
| 1296 |
at the interface, plus the number of SVCCs |
| 1297 |
that are currently established at the |
| 1298 |
interface." |
| 1299 |
::= { atmInterfaceConfEntry 4} |
| 1300 |
|
| 1301 |
atmInterfaceMaxActiveVpiBits OBJECT-TYPE |
| 1302 |
SYNTAX INTEGER (0..12) |
| 1303 |
MAX-ACCESS read-write |
| 1304 |
STATUS current |
| 1305 |
DESCRIPTION |
| 1306 |
"The maximum number of active VPI bits |
| 1307 |
configured for use at the ATM interface. |
| 1308 |
At the ATM UNI, the maximum number of active |
| 1309 |
VPI bits configured for use ranges from |
| 1310 |
0 to 8 only." |
| 1311 |
::= { atmInterfaceConfEntry 5} |
| 1312 |
|
| 1313 |
atmInterfaceMaxActiveVciBits OBJECT-TYPE |
| 1314 |
SYNTAX INTEGER (0..16) |
| 1315 |
MAX-ACCESS read-write |
| 1316 |
STATUS current |
| 1317 |
DESCRIPTION |
| 1318 |
"The maximum number of active VCI bits |
| 1319 |
configured for use at this ATM interface." |
| 1320 |
::= { atmInterfaceConfEntry 6} |
| 1321 |
|
| 1322 |
atmInterfaceIlmiVpi OBJECT-TYPE |
| 1323 |
SYNTAX AtmVpIdentifier |
| 1324 |
MAX-ACCESS read-write |
| 1325 |
STATUS current |
| 1326 |
DESCRIPTION |
| 1327 |
"The VPI value of the VCC supporting |
| 1328 |
the ILMI at this ATM interface. If the values of |
| 1329 |
atmInterfaceIlmiVpi and atmInterfaceIlmiVci are |
| 1330 |
both equal to zero then the ILMI is not |
| 1331 |
supported at this ATM interface." |
| 1332 |
DEFVAL { 0 } |
| 1333 |
::= { atmInterfaceConfEntry 7} |
| 1334 |
|
| 1335 |
atmInterfaceIlmiVci OBJECT-TYPE |
| 1336 |
SYNTAX AtmVcIdentifier |
| 1337 |
|
| 1338 |
|
| 1339 |
|
| 1340 |
<span class="grey">Tesink Standards Track [Page 24]</span></pre> |
| 1341 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-25" ></span> |
| 1342 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1343 |
|
| 1344 |
|
| 1345 |
MAX-ACCESS read-write |
| 1346 |
STATUS current |
| 1347 |
DESCRIPTION |
| 1348 |
"The VCI value of the VCC supporting |
| 1349 |
the ILMI at this ATM interface. If the values of |
| 1350 |
atmInterfaceIlmiVpi and atmInterfaceIlmiVci are |
| 1351 |
both equal to zero then the ILMI is not |
| 1352 |
supported at this ATM interface." |
| 1353 |
DEFVAL { 16 } |
| 1354 |
::= { atmInterfaceConfEntry 8} |
| 1355 |
|
| 1356 |
atmInterfaceAddressType OBJECT-TYPE |
| 1357 |
SYNTAX INTEGER { |
| 1358 |
private(1), |
| 1359 |
nsapE164(2), |
| 1360 |
nativeE164(3), |
| 1361 |
other(4) |
| 1362 |
} |
| 1363 |
MAX-ACCESS read-only |
| 1364 |
STATUS deprecated |
| 1365 |
DESCRIPTION |
| 1366 |
"The type of primary ATM address configured |
| 1367 |
for use at this ATM interface." |
| 1368 |
::= { atmInterfaceConfEntry 9 } |
| 1369 |
|
| 1370 |
-- The atmInterfaceAdminAddress object has been replaced by |
| 1371 |
-- atmInterfaceSubscrAddress. |
| 1372 |
|
| 1373 |
atmInterfaceAdminAddress OBJECT-TYPE |
| 1374 |
SYNTAX AtmAddr |
| 1375 |
MAX-ACCESS read-only |
| 1376 |
STATUS deprecated |
| 1377 |
DESCRIPTION |
| 1378 |
"The primary address assigned for administrative purposes, |
| 1379 |
for example, an address associated with the |
| 1380 |
service provider side of a public network UNI |
| 1381 |
(thus, the value of this address corresponds |
| 1382 |
with the value of ifPhysAddress at the host side). |
| 1383 |
If this interface has no assigned administrative |
| 1384 |
address, or when the address used for |
| 1385 |
administrative purposes is the same as that used |
| 1386 |
for ifPhysAddress, then this is an octet string of |
| 1387 |
zero length." |
| 1388 |
::= { atmInterfaceConfEntry 10 } |
| 1389 |
|
| 1390 |
atmInterfaceMyNeighborIpAddress OBJECT-TYPE |
| 1391 |
SYNTAX IpAddress |
| 1392 |
MAX-ACCESS read-write |
| 1393 |
|
| 1394 |
|
| 1395 |
|
| 1396 |
<span class="grey">Tesink Standards Track [Page 25]</span></pre> |
| 1397 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-26" ></span> |
| 1398 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1399 |
|
| 1400 |
|
| 1401 |
STATUS current |
| 1402 |
DESCRIPTION |
| 1403 |
"The IP address of the neighbor system connected to |
| 1404 |
the far end of this interface, to which a Network |
| 1405 |
Management Station can send SNMP messages, as IP |
| 1406 |
datagrams sent to UDP port 161, in order to access |
| 1407 |
network management information concerning the |
| 1408 |
operation of that system. Note that the value |
| 1409 |
of this object may be obtained in different ways, |
| 1410 |
e.g., by manual configuration, or through ILMI |
| 1411 |
interaction with the neighbor system." |
| 1412 |
::= { atmInterfaceConfEntry 11 } |
| 1413 |
|
| 1414 |
atmInterfaceMyNeighborIfName OBJECT-TYPE |
| 1415 |
SYNTAX DisplayString |
| 1416 |
MAX-ACCESS read-write |
| 1417 |
STATUS current |
| 1418 |
DESCRIPTION |
| 1419 |
"The textual name of the interface on the neighbor |
| 1420 |
system on the far end of this interface, and to |
| 1421 |
which this interface connects. If the neighbor |
| 1422 |
system is manageable through SNMP and supports |
| 1423 |
the object ifName, the value of this object must |
| 1424 |
be identical with that of ifName for the ifEntry |
| 1425 |
of the lowest level physical interface |
| 1426 |
for this port. If this interface does not have a |
| 1427 |
textual name, the value of this object is a zero |
| 1428 |
length string. Note that the value of this object |
| 1429 |
may be obtained in different ways, e.g., by manual |
| 1430 |
configuration, or through ILMI interaction with |
| 1431 |
the neighbor system." |
| 1432 |
::= { atmInterfaceConfEntry 12 } |
| 1433 |
|
| 1434 |
atmInterfaceCurrentMaxVpiBits OBJECT-TYPE |
| 1435 |
SYNTAX INTEGER (0..12) |
| 1436 |
MAX-ACCESS read-only |
| 1437 |
STATUS current |
| 1438 |
DESCRIPTION |
| 1439 |
"The maximum number of VPI Bits that may |
| 1440 |
currently be used at this ATM interface. |
| 1441 |
The value is the minimum of |
| 1442 |
atmInterfaceMaxActiveVpiBits, and the |
| 1443 |
atmInterfaceMaxActiveVpiBits of the interface's |
| 1444 |
UNI/NNI peer. |
| 1445 |
|
| 1446 |
If the interface does not negotiate with |
| 1447 |
its peer to determine the number of VPI Bits |
| 1448 |
that can be used on the interface, then the |
| 1449 |
|
| 1450 |
|
| 1451 |
|
| 1452 |
<span class="grey">Tesink Standards Track [Page 26]</span></pre> |
| 1453 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-27" ></span> |
| 1454 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1455 |
|
| 1456 |
|
| 1457 |
value of this object must equal |
| 1458 |
atmInterfaceMaxActiveVpiBits." |
| 1459 |
::= { atmInterfaceConfEntry 13 } |
| 1460 |
|
| 1461 |
atmInterfaceCurrentMaxVciBits OBJECT-TYPE |
| 1462 |
SYNTAX INTEGER (0..16) |
| 1463 |
MAX-ACCESS read-only |
| 1464 |
STATUS current |
| 1465 |
DESCRIPTION |
| 1466 |
"The maximum number of VCI Bits that may |
| 1467 |
currently be used at this ATM interface. |
| 1468 |
The value is the minimum of |
| 1469 |
atmInterfaceMaxActiveVciBits, and the |
| 1470 |
atmInterfaceMaxActiveVciBits of the interface's |
| 1471 |
UNI/NNI peer. |
| 1472 |
|
| 1473 |
If the interface does not negotiate with |
| 1474 |
its peer to determine the number of VCI Bits |
| 1475 |
that can be used on the interface, then the |
| 1476 |
value of this object must equal |
| 1477 |
atmInterfaceMaxActiveVciBits." |
| 1478 |
::= { atmInterfaceConfEntry 14 } |
| 1479 |
|
| 1480 |
atmInterfaceSubscrAddress OBJECT-TYPE |
| 1481 |
SYNTAX AtmAddr |
| 1482 |
MAX-ACCESS read-write |
| 1483 |
STATUS current |
| 1484 |
DESCRIPTION |
| 1485 |
"The identifier assigned by a service provider |
| 1486 |
to the network side of a public network UNI. |
| 1487 |
If this interface has no assigned service provider |
| 1488 |
address, or for other interfaces this is an octet string |
| 1489 |
of zero length." |
| 1490 |
::= { atmInterfaceConfEntry 15 } |
| 1491 |
|
| 1492 |
-- The ATM Interface DS3 PLCP Table |
| 1493 |
|
| 1494 |
-- This table contains the DS3 PLCP configuration and |
| 1495 |
-- state parameters of those ATM interfaces |
| 1496 |
-- which use DS3 PLCP for carrying ATM cells over DS3. |
| 1497 |
|
| 1498 |
atmInterfaceDs3PlcpTable OBJECT-TYPE |
| 1499 |
SYNTAX SEQUENCE OF AtmInterfaceDs3PlcpEntry |
| 1500 |
MAX-ACCESS not-accessible |
| 1501 |
STATUS current |
| 1502 |
DESCRIPTION |
| 1503 |
"This table contains ATM interface DS3 PLCP |
| 1504 |
parameters and state variables, one entry per |
| 1505 |
|
| 1506 |
|
| 1507 |
|
| 1508 |
<span class="grey">Tesink Standards Track [Page 27]</span></pre> |
| 1509 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-28" ></span> |
| 1510 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1511 |
|
| 1512 |
|
| 1513 |
ATM interface port." |
| 1514 |
::= { atmMIBObjects 3} |
| 1515 |
|
| 1516 |
atmInterfaceDs3PlcpEntry OBJECT-TYPE |
| 1517 |
SYNTAX AtmInterfaceDs3PlcpEntry |
| 1518 |
MAX-ACCESS not-accessible |
| 1519 |
STATUS current |
| 1520 |
DESCRIPTION |
| 1521 |
"This list contains DS3 PLCP parameters and |
| 1522 |
state variables at the ATM interface and is |
| 1523 |
indexed by the ifIndex value of the ATM interface." |
| 1524 |
INDEX { ifIndex } |
| 1525 |
::= { atmInterfaceDs3PlcpTable 1} |
| 1526 |
|
| 1527 |
AtmInterfaceDs3PlcpEntry ::= SEQUENCE { |
| 1528 |
atmInterfaceDs3PlcpSEFSs Counter32, |
| 1529 |
atmInterfaceDs3PlcpAlarmState INTEGER, |
| 1530 |
atmInterfaceDs3PlcpUASs Counter32 |
| 1531 |
} |
| 1532 |
|
| 1533 |
|
| 1534 |
atmInterfaceDs3PlcpSEFSs OBJECT-TYPE |
| 1535 |
SYNTAX Counter32 |
| 1536 |
MAX-ACCESS read-only |
| 1537 |
STATUS current |
| 1538 |
DESCRIPTION |
| 1539 |
"The number of DS3 PLCP Severely Errored Framing |
| 1540 |
Seconds (SEFS). Each SEFS represents a |
| 1541 |
one-second interval which contains |
| 1542 |
one or more SEF events." |
| 1543 |
::= { atmInterfaceDs3PlcpEntry 1} |
| 1544 |
|
| 1545 |
atmInterfaceDs3PlcpAlarmState OBJECT-TYPE |
| 1546 |
SYNTAX INTEGER { |
| 1547 |
noAlarm(1), |
| 1548 |
receivedFarEndAlarm(2), |
| 1549 |
incomingLOF(3) |
| 1550 |
} |
| 1551 |
MAX-ACCESS read-only |
| 1552 |
STATUS current |
| 1553 |
DESCRIPTION |
| 1554 |
"This variable indicates if there is an |
| 1555 |
alarm present for the DS3 PLCP. The value |
| 1556 |
receivedFarEndAlarm means that the DS3 PLCP |
| 1557 |
has received an incoming Yellow |
| 1558 |
Signal, the value incomingLOF means that |
| 1559 |
the DS3 PLCP has declared a loss of frame (LOF) |
| 1560 |
failure condition, and the value noAlarm |
| 1561 |
|
| 1562 |
|
| 1563 |
|
| 1564 |
<span class="grey">Tesink Standards Track [Page 28]</span></pre> |
| 1565 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-29" ></span> |
| 1566 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1567 |
|
| 1568 |
|
| 1569 |
means that there are no alarms present. |
| 1570 |
Transition from the failure to the no alarm state |
| 1571 |
occurs when no defects (e.g., LOF) are received |
| 1572 |
for more than 10 seconds." |
| 1573 |
::= { atmInterfaceDs3PlcpEntry 2} |
| 1574 |
|
| 1575 |
atmInterfaceDs3PlcpUASs OBJECT-TYPE |
| 1576 |
SYNTAX Counter32 |
| 1577 |
MAX-ACCESS read-only |
| 1578 |
STATUS current |
| 1579 |
DESCRIPTION |
| 1580 |
"The counter associated with the number of |
| 1581 |
Unavailable Seconds encountered by the PLCP." |
| 1582 |
::= { atmInterfaceDs3PlcpEntry 3} |
| 1583 |
|
| 1584 |
|
| 1585 |
-- The ATM Interface TC Sublayer Table |
| 1586 |
|
| 1587 |
-- This table contains TC sublayer configuration and |
| 1588 |
-- state parameters of those ATM interfaces |
| 1589 |
-- which use TC sublayer for carrying ATM cells over |
| 1590 |
-- SONET/SDH or DS3. |
| 1591 |
|
| 1592 |
|
| 1593 |
atmInterfaceTCTable OBJECT-TYPE |
| 1594 |
SYNTAX SEQUENCE OF AtmInterfaceTCEntry |
| 1595 |
MAX-ACCESS not-accessible |
| 1596 |
STATUS current |
| 1597 |
DESCRIPTION |
| 1598 |
"This table contains ATM interface TC |
| 1599 |
Sublayer parameters and state variables, |
| 1600 |
one entry per ATM interface port." |
| 1601 |
::= { atmMIBObjects 4} |
| 1602 |
|
| 1603 |
atmInterfaceTCEntry OBJECT-TYPE |
| 1604 |
SYNTAX AtmInterfaceTCEntry |
| 1605 |
MAX-ACCESS not-accessible |
| 1606 |
STATUS current |
| 1607 |
DESCRIPTION |
| 1608 |
"This list contains TC Sublayer parameters |
| 1609 |
and state variables at the ATM interface and is |
| 1610 |
indexed by the ifIndex value of the ATM interface." |
| 1611 |
INDEX {ifIndex } |
| 1612 |
::= { atmInterfaceTCTable 1} |
| 1613 |
|
| 1614 |
AtmInterfaceTCEntry ::= SEQUENCE { |
| 1615 |
atmInterfaceOCDEvents Counter32, |
| 1616 |
atmInterfaceTCAlarmState INTEGER |
| 1617 |
|
| 1618 |
|
| 1619 |
|
| 1620 |
<span class="grey">Tesink Standards Track [Page 29]</span></pre> |
| 1621 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-30" ></span> |
| 1622 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1623 |
|
| 1624 |
|
| 1625 |
} |
| 1626 |
|
| 1627 |
atmInterfaceOCDEvents OBJECT-TYPE |
| 1628 |
SYNTAX Counter32 |
| 1629 |
MAX-ACCESS read-only |
| 1630 |
STATUS current |
| 1631 |
DESCRIPTION |
| 1632 |
"The number of times the Out of Cell |
| 1633 |
Delineation (OCD) events occur. If seven |
| 1634 |
consecutive ATM cells have Header Error |
| 1635 |
Control (HEC) violations, an OCD event occurs. |
| 1636 |
A high number of OCD events may indicate a |
| 1637 |
problem with the TC Sublayer." |
| 1638 |
::= { atmInterfaceTCEntry 1} |
| 1639 |
|
| 1640 |
|
| 1641 |
atmInterfaceTCAlarmState OBJECT-TYPE |
| 1642 |
SYNTAX INTEGER { |
| 1643 |
noAlarm(1), |
| 1644 |
lcdFailure(2) |
| 1645 |
} |
| 1646 |
MAX-ACCESS read-only |
| 1647 |
STATUS current |
| 1648 |
DESCRIPTION |
| 1649 |
"This variable indicates if there is an |
| 1650 |
alarm present for the TC Sublayer. The value |
| 1651 |
lcdFailure(2) indicates that the TC Sublayer |
| 1652 |
is currently in the Loss of Cell Delineation |
| 1653 |
(LCD) defect maintenance state. The value |
| 1654 |
noAlarm(1) indicates that the TC Sublayer |
| 1655 |
is currently not in the LCD defect |
| 1656 |
maintenance state." |
| 1657 |
::= { atmInterfaceTCEntry 2} |
| 1658 |
|
| 1659 |
-- ATM Traffic Descriptor Parameter Table |
| 1660 |
|
| 1661 |
-- This table contains a set of self-consistent |
| 1662 |
-- ATM traffic parameters including the |
| 1663 |
-- ATM traffic service category. |
| 1664 |
|
| 1665 |
-- The ATM virtual link tables (i.e., VPL and VCL tables) |
| 1666 |
-- will use this ATM Traffic Descriptor table |
| 1667 |
-- to assign traffic parameters and service category |
| 1668 |
-- to the receive and transmit directions of |
| 1669 |
-- the ATM virtual links (i.e., VPLs and VCLs). |
| 1670 |
-- The ATM VPL or VCL table will indicate a row |
| 1671 |
-- in the atmTrafficDescrParamTable |
| 1672 |
-- using its atmTrafficDescrParamIndex value. |
| 1673 |
|
| 1674 |
|
| 1675 |
|
| 1676 |
<span class="grey">Tesink Standards Track [Page 30]</span></pre> |
| 1677 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-31" ></span> |
| 1678 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1679 |
|
| 1680 |
|
| 1681 |
-- The management application can then compare a set of |
| 1682 |
-- ATM traffic parameters with a single value. |
| 1683 |
|
| 1684 |
-- If no suitable row(s) in the atmTrafficDescrParamTable |
| 1685 |
-- exists, the manager must create a new row(s) in this |
| 1686 |
-- table. If such a row is created, agent checks the |
| 1687 |
-- sanity of that set of ATM traffic parameter values. |
| 1688 |
|
| 1689 |
-- The manager may use atmTrafficDescrParamIndexNext |
| 1690 |
-- in order to obtain a free atmTrafficDescrParamIndex |
| 1691 |
-- value. |
| 1692 |
|
| 1693 |
-- When creating a new row, the parameter values |
| 1694 |
-- will be checked for self-consistency. |
| 1695 |
-- Predefined/template rows may be supported. |
| 1696 |
|
| 1697 |
-- A row in the atmTrafficDescrParamTable is deleted |
| 1698 |
-- by setting the atmTrafficDescrRowStatus to destroy(6). |
| 1699 |
-- The agent will check whether this row is still in use |
| 1700 |
-- by any entry of the atmVplTable or atmVclTable. |
| 1701 |
-- The agent denies the request if the row is still in |
| 1702 |
-- use. |
| 1703 |
|
| 1704 |
-- The ATM Traffic Descriptor Parameter Table |
| 1705 |
|
| 1706 |
|
| 1707 |
atmTrafficDescrParamTable OBJECT-TYPE |
| 1708 |
SYNTAX SEQUENCE OF AtmTrafficDescrParamEntry |
| 1709 |
MAX-ACCESS not-accessible |
| 1710 |
STATUS current |
| 1711 |
DESCRIPTION |
| 1712 |
"This table contains information on ATM traffic |
| 1713 |
descriptor type and the associated parameters." |
| 1714 |
::= { atmMIBObjects 5} |
| 1715 |
|
| 1716 |
atmTrafficDescrParamEntry OBJECT-TYPE |
| 1717 |
SYNTAX AtmTrafficDescrParamEntry |
| 1718 |
MAX-ACCESS not-accessible |
| 1719 |
STATUS current |
| 1720 |
DESCRIPTION |
| 1721 |
"This list contains ATM traffic descriptor |
| 1722 |
type and the associated parameters." |
| 1723 |
INDEX {atmTrafficDescrParamIndex} |
| 1724 |
::= { atmTrafficDescrParamTable 1} |
| 1725 |
|
| 1726 |
AtmTrafficDescrParamEntry ::= SEQUENCE { |
| 1727 |
atmTrafficDescrParamIndex AtmTrafficDescrParamIndex, |
| 1728 |
atmTrafficDescrType OBJECT IDENTIFIER, |
| 1729 |
|
| 1730 |
|
| 1731 |
|
| 1732 |
<span class="grey">Tesink Standards Track [Page 31]</span></pre> |
| 1733 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-32" ></span> |
| 1734 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1735 |
|
| 1736 |
|
| 1737 |
atmTrafficDescrParam1 Integer32, |
| 1738 |
atmTrafficDescrParam2 Integer32, |
| 1739 |
atmTrafficDescrParam3 Integer32, |
| 1740 |
atmTrafficDescrParam4 Integer32, |
| 1741 |
atmTrafficDescrParam5 Integer32, |
| 1742 |
atmTrafficQoSClass INTEGER, |
| 1743 |
atmTrafficDescrRowStatus RowStatus, |
| 1744 |
atmServiceCategory AtmServiceCategory, |
| 1745 |
atmTrafficFrameDiscard TruthValue |
| 1746 |
} |
| 1747 |
|
| 1748 |
atmTrafficDescrParamIndex OBJECT-TYPE |
| 1749 |
SYNTAX AtmTrafficDescrParamIndex (1..2147483647) |
| 1750 |
MAX-ACCESS not-accessible |
| 1751 |
STATUS current |
| 1752 |
DESCRIPTION |
| 1753 |
"This object is used by the virtual link |
| 1754 |
table (i.e., VPL or VCL table) |
| 1755 |
to identify the row of this table. |
| 1756 |
When creating a new row in the table |
| 1757 |
the value of this index may be obtained |
| 1758 |
by retrieving the value of |
| 1759 |
atmTrafficDescrParamIndexNext." |
| 1760 |
::= { atmTrafficDescrParamEntry 1} |
| 1761 |
|
| 1762 |
atmTrafficDescrType OBJECT-TYPE |
| 1763 |
SYNTAX OBJECT IDENTIFIER |
| 1764 |
MAX-ACCESS read-create |
| 1765 |
STATUS current |
| 1766 |
DESCRIPTION |
| 1767 |
"The value of this object identifies the type |
| 1768 |
of ATM traffic descriptor. |
| 1769 |
The type may indicate no traffic descriptor or |
| 1770 |
traffic descriptor with one or more parameters. |
| 1771 |
These parameters are specified as a parameter |
| 1772 |
vector, in the corresponding instances of the |
| 1773 |
objects: |
| 1774 |
atmTrafficDescrParam1 |
| 1775 |
atmTrafficDescrParam2 |
| 1776 |
atmTrafficDescrParam3 |
| 1777 |
atmTrafficDescrParam4 |
| 1778 |
atmTrafficDescrParam5." |
| 1779 |
DEFVAL { atmNoClpNoScr } |
| 1780 |
::= { atmTrafficDescrParamEntry 2} |
| 1781 |
|
| 1782 |
atmTrafficDescrParam1 OBJECT-TYPE |
| 1783 |
SYNTAX Integer32 |
| 1784 |
MAX-ACCESS read-create |
| 1785 |
|
| 1786 |
|
| 1787 |
|
| 1788 |
<span class="grey">Tesink Standards Track [Page 32]</span></pre> |
| 1789 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-33" ></span> |
| 1790 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1791 |
|
| 1792 |
|
| 1793 |
STATUS current |
| 1794 |
DESCRIPTION |
| 1795 |
"The first parameter of the ATM traffic descriptor |
| 1796 |
used according to the value of |
| 1797 |
atmTrafficDescrType." |
| 1798 |
DEFVAL { 0 } |
| 1799 |
::= { atmTrafficDescrParamEntry 3} |
| 1800 |
|
| 1801 |
atmTrafficDescrParam2 OBJECT-TYPE |
| 1802 |
SYNTAX Integer32 |
| 1803 |
MAX-ACCESS read-create |
| 1804 |
STATUS current |
| 1805 |
DESCRIPTION |
| 1806 |
"The second parameter of the ATM traffic descriptor |
| 1807 |
used according to the value of |
| 1808 |
atmTrafficDescrType." |
| 1809 |
DEFVAL { 0 } |
| 1810 |
::= { atmTrafficDescrParamEntry 4} |
| 1811 |
|
| 1812 |
atmTrafficDescrParam3 OBJECT-TYPE |
| 1813 |
SYNTAX Integer32 |
| 1814 |
MAX-ACCESS read-create |
| 1815 |
STATUS current |
| 1816 |
DESCRIPTION |
| 1817 |
"The third parameter of the ATM traffic descriptor |
| 1818 |
used according to the value of |
| 1819 |
atmTrafficDescrType." |
| 1820 |
DEFVAL { 0 } |
| 1821 |
::= { atmTrafficDescrParamEntry 5} |
| 1822 |
|
| 1823 |
atmTrafficDescrParam4 OBJECT-TYPE |
| 1824 |
SYNTAX Integer32 |
| 1825 |
MAX-ACCESS read-create |
| 1826 |
STATUS current |
| 1827 |
DESCRIPTION |
| 1828 |
"The fourth parameter of the ATM traffic descriptor |
| 1829 |
used according to the value of |
| 1830 |
atmTrafficDescrType." |
| 1831 |
DEFVAL { 0 } |
| 1832 |
::= { atmTrafficDescrParamEntry 6} |
| 1833 |
|
| 1834 |
atmTrafficDescrParam5 OBJECT-TYPE |
| 1835 |
SYNTAX Integer32 |
| 1836 |
MAX-ACCESS read-create |
| 1837 |
STATUS current |
| 1838 |
DESCRIPTION |
| 1839 |
"The fifth parameter of the ATM traffic descriptor |
| 1840 |
used according to the value of |
| 1841 |
|
| 1842 |
|
| 1843 |
|
| 1844 |
<span class="grey">Tesink Standards Track [Page 33]</span></pre> |
| 1845 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-34" ></span> |
| 1846 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1847 |
|
| 1848 |
|
| 1849 |
atmTrafficDescrType." |
| 1850 |
DEFVAL { 0 } |
| 1851 |
::= { atmTrafficDescrParamEntry 7} |
| 1852 |
|
| 1853 |
atmTrafficQoSClass OBJECT-TYPE |
| 1854 |
SYNTAX INTEGER (0..255) |
| 1855 |
MAX-ACCESS read-create |
| 1856 |
STATUS deprecated |
| 1857 |
DESCRIPTION |
| 1858 |
"The value of this object identifies the QoS Class. |
| 1859 |
Four Service classes have been |
| 1860 |
specified in the ATM Forum UNI Specification: |
| 1861 |
Service Class A: Constant bit rate video and |
| 1862 |
Circuit emulation |
| 1863 |
Service Class B: Variable bit rate video/audio |
| 1864 |
Service Class C: Connection-oriented data |
| 1865 |
Service Class D: Connectionless data |
| 1866 |
Four QoS classes numbered 1, 2, 3, and 4 have |
| 1867 |
been specified with the aim to support service |
| 1868 |
classes A, B, C, and D respectively. |
| 1869 |
An unspecified QoS Class numbered `0' is used |
| 1870 |
for best effort traffic." |
| 1871 |
DEFVAL { 0 } |
| 1872 |
::= { atmTrafficDescrParamEntry 8} |
| 1873 |
|
| 1874 |
atmTrafficDescrRowStatus OBJECT-TYPE |
| 1875 |
SYNTAX RowStatus |
| 1876 |
MAX-ACCESS read-create |
| 1877 |
STATUS current |
| 1878 |
DESCRIPTION |
| 1879 |
"This object is used to create |
| 1880 |
a new row or modify or delete an |
| 1881 |
existing row in this table." |
| 1882 |
DEFVAL { active } |
| 1883 |
::= {atmTrafficDescrParamEntry 9} |
| 1884 |
|
| 1885 |
atmServiceCategory OBJECT-TYPE |
| 1886 |
SYNTAX AtmServiceCategory |
| 1887 |
MAX-ACCESS read-create |
| 1888 |
STATUS current |
| 1889 |
DESCRIPTION |
| 1890 |
"The ATM service category." |
| 1891 |
DEFVAL { ubr } |
| 1892 |
::= { atmTrafficDescrParamEntry 10} |
| 1893 |
|
| 1894 |
|
| 1895 |
atmTrafficFrameDiscard OBJECT-TYPE |
| 1896 |
SYNTAX TruthValue |
| 1897 |
|
| 1898 |
|
| 1899 |
|
| 1900 |
<span class="grey">Tesink Standards Track [Page 34]</span></pre> |
| 1901 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-35" ></span> |
| 1902 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1903 |
|
| 1904 |
|
| 1905 |
MAX-ACCESS read-create |
| 1906 |
STATUS current |
| 1907 |
DESCRIPTION |
| 1908 |
"If set to 'true', this object indicates that the network |
| 1909 |
is requested to treat data for this connection, in the |
| 1910 |
given direction, as frames (e.g. AAL5 CPCS_PDU's) rather |
| 1911 |
than as individual cells. While the precise |
| 1912 |
implementation is network-specific, this treatment may |
| 1913 |
for example involve discarding entire frames during |
| 1914 |
congestion, rather than a few cells from many frames." |
| 1915 |
DEFVAL { true } |
| 1916 |
::= { atmTrafficDescrParamEntry 11 } |
| 1917 |
|
| 1918 |
-- ATM Interface Virtual Path Link (VPL) Table |
| 1919 |
|
| 1920 |
-- This table contains configuration and state |
| 1921 |
-- information of a bi-directional Virtual Path Link |
| 1922 |
-- (VPL) |
| 1923 |
|
| 1924 |
-- This table can be used to create, delete or modify |
| 1925 |
-- a VPL that is terminated in an ATM host or switch. |
| 1926 |
-- This table can also be used to create, delete or |
| 1927 |
-- modify a VPL which is cross-connected to another |
| 1928 |
-- VPL. |
| 1929 |
|
| 1930 |
-- In the example below, the traffic flows on the receive |
| 1931 |
-- and transmit directions of the VPLs are characterized |
| 1932 |
-- by atmVplReceiveTrafficDescrIndex and |
| 1933 |
-- atmVplTransmitTrafficDescrIndex respectively. |
| 1934 |
-- The cross-connected VPLs are identified by |
| 1935 |
-- atmVplCrossConnectIdentifier. |
| 1936 |
|
| 1937 |
|
| 1938 |
|
| 1939 |
-- ________________________________ |
| 1940 |
-- | | |
| 1941 |
-- VPL | ATM Host, Switch, or Network | VPL |
| 1942 |
-- receive | | receive |
| 1943 |
-- ========> X X <======= |
| 1944 |
-- <======== X X ========> |
| 1945 |
-- transmit | | transmit |
| 1946 |
-- |______________________________| |
| 1947 |
|
| 1948 |
|
| 1949 |
|
| 1950 |
-- The ATM Interface VPL Table |
| 1951 |
|
| 1952 |
|
| 1953 |
|
| 1954 |
|
| 1955 |
|
| 1956 |
<span class="grey">Tesink Standards Track [Page 35]</span></pre> |
| 1957 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-36" ></span> |
| 1958 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 1959 |
|
| 1960 |
|
| 1961 |
atmVplTable OBJECT-TYPE |
| 1962 |
SYNTAX SEQUENCE OF AtmVplEntry |
| 1963 |
MAX-ACCESS not-accessible |
| 1964 |
STATUS current |
| 1965 |
DESCRIPTION |
| 1966 |
"The Virtual Path Link (VPL) table. A |
| 1967 |
bi-directional VPL is modeled as one entry |
| 1968 |
in this table. This table can be used for |
| 1969 |
PVCs, SVCs and Soft PVCs. |
| 1970 |
Entries are not present in this table for |
| 1971 |
the VPIs used by entries in the atmVclTable." |
| 1972 |
::= { atmMIBObjects 6} |
| 1973 |
|
| 1974 |
atmVplEntry OBJECT-TYPE |
| 1975 |
SYNTAX AtmVplEntry |
| 1976 |
MAX-ACCESS not-accessible |
| 1977 |
STATUS current |
| 1978 |
DESCRIPTION |
| 1979 |
"An entry in the VPL table. This entry is |
| 1980 |
used to model a bi-directional VPL. |
| 1981 |
To create a VPL at an ATM interface, |
| 1982 |
either of the following procedures are used: |
| 1983 |
|
| 1984 |
Negotiated VPL establishment |
| 1985 |
|
| 1986 |
(1) The management application creates |
| 1987 |
a VPL entry in the atmVplTable |
| 1988 |
by setting atmVplRowStatus to createAndWait(5). |
| 1989 |
This may fail for the following reasons: |
| 1990 |
- The selected VPI value is unavailable, |
| 1991 |
- The selected VPI value is in use. |
| 1992 |
Otherwise, the agent creates a row and |
| 1993 |
reserves the VPI value on that port. |
| 1994 |
|
| 1995 |
(2) The manager selects an existing row(s) in the |
| 1996 |
atmTrafficDescrParamTable, |
| 1997 |
thereby, selecting a set of self-consistent |
| 1998 |
ATM traffic parameters and the service category |
| 1999 |
for receive and transmit directions of the VPL. |
| 2000 |
|
| 2001 |
(2a) If no suitable row(s) in the |
| 2002 |
atmTrafficDescrParamTable exists, |
| 2003 |
the manager must create a new row(s) |
| 2004 |
in that table. |
| 2005 |
|
| 2006 |
(2b) The manager characterizes the VPL's traffic |
| 2007 |
parameters through setting the |
| 2008 |
atmVplReceiveTrafficDescrIndex and the |
| 2009 |
|
| 2010 |
|
| 2011 |
|
| 2012 |
<span class="grey">Tesink Standards Track [Page 36]</span></pre> |
| 2013 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-37" ></span> |
| 2014 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2015 |
|
| 2016 |
|
| 2017 |
atmVplTransmitTrafficDescrIndex values |
| 2018 |
in the VPL table, which point to the rows |
| 2019 |
containing desired ATM traffic parameter values |
| 2020 |
in the atmTrafficDescrParamTable. The agent |
| 2021 |
will check the availability of resources and |
| 2022 |
may refuse the request. |
| 2023 |
If the transmit and receive service categories |
| 2024 |
are inconsistent, the agent should refuse the |
| 2025 |
request. |
| 2026 |
|
| 2027 |
(3) The manager activates the VPL by setting the |
| 2028 |
the atmVplRowStatus to active(1). |
| 2029 |
If this set is successful, the agent has |
| 2030 |
reserved the resources to satisfy the requested |
| 2031 |
traffic parameter values and the service category |
| 2032 |
for that VPL. |
| 2033 |
|
| 2034 |
(4) If the VPL terminates a VPC in the ATM host |
| 2035 |
or switch, the manager turns on the |
| 2036 |
atmVplAdminStatus to up(1) to turn the VPL |
| 2037 |
traffic flow on. Otherwise, the |
| 2038 |
atmVpCrossConnectTable must be used |
| 2039 |
to cross-connect the VPL to another VPL(s) |
| 2040 |
in an ATM switch or network. |
| 2041 |
|
| 2042 |
One-Shot VPL Establishment |
| 2043 |
|
| 2044 |
A VPL may also be established in one step by a |
| 2045 |
set-request with all necessary VPL parameter |
| 2046 |
values and atmVplRowStatus set to createAndGo(4). |
| 2047 |
|
| 2048 |
In contrast to the negotiated VPL establishment |
| 2049 |
which allows for detailed error checking |
| 2050 |
(i.e., set errors are explicitly linked to |
| 2051 |
particular resource acquisition failures), |
| 2052 |
the one-shot VPL establishment |
| 2053 |
performs the setup on one operation but |
| 2054 |
does not have the advantage of step-wise |
| 2055 |
error checking. |
| 2056 |
|
| 2057 |
VPL Retirement |
| 2058 |
|
| 2059 |
A VPL is released by setting atmVplRowStatus to |
| 2060 |
destroy(6), and the agent may release all |
| 2061 |
associated resources." |
| 2062 |
INDEX {ifIndex, atmVplVpi } |
| 2063 |
::= { atmVplTable 1} |
| 2064 |
|
| 2065 |
|
| 2066 |
|
| 2067 |
|
| 2068 |
<span class="grey">Tesink Standards Track [Page 37]</span></pre> |
| 2069 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-38" ></span> |
| 2070 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2071 |
|
| 2072 |
|
| 2073 |
AtmVplEntry ::= SEQUENCE { |
| 2074 |
atmVplVpi AtmVpIdentifier, |
| 2075 |
atmVplAdminStatus AtmVorXAdminStatus, |
| 2076 |
atmVplOperStatus AtmVorXOperStatus, |
| 2077 |
atmVplLastChange AtmVorXLastChange, |
| 2078 |
atmVplReceiveTrafficDescrIndex |
| 2079 |
AtmTrafficDescrParamIndex, |
| 2080 |
atmVplTransmitTrafficDescrIndex |
| 2081 |
AtmTrafficDescrParamIndex, |
| 2082 |
atmVplCrossConnectIdentifier INTEGER, |
| 2083 |
atmVplRowStatus RowStatus, |
| 2084 |
atmVplCastType AtmConnCastType, |
| 2085 |
atmVplConnKind AtmConnKind |
| 2086 |
} |
| 2087 |
|
| 2088 |
|
| 2089 |
atmVplVpi OBJECT-TYPE |
| 2090 |
SYNTAX AtmVpIdentifier |
| 2091 |
MAX-ACCESS not-accessible |
| 2092 |
STATUS current |
| 2093 |
DESCRIPTION |
| 2094 |
"The VPI value of the VPL." |
| 2095 |
::= { atmVplEntry 1} |
| 2096 |
|
| 2097 |
atmVplAdminStatus OBJECT-TYPE |
| 2098 |
SYNTAX AtmVorXAdminStatus |
| 2099 |
MAX-ACCESS read-create |
| 2100 |
STATUS current |
| 2101 |
DESCRIPTION |
| 2102 |
"This object is instanciated only for a VPL |
| 2103 |
which terminates a VPC (i.e., one which is |
| 2104 |
NOT cross-connected to other VPLs). |
| 2105 |
Its value specifies the desired |
| 2106 |
administrative state of the VPL." |
| 2107 |
DEFVAL { down } |
| 2108 |
::= { atmVplEntry 2} |
| 2109 |
|
| 2110 |
atmVplOperStatus OBJECT-TYPE |
| 2111 |
SYNTAX AtmVorXOperStatus |
| 2112 |
MAX-ACCESS read-only |
| 2113 |
STATUS current |
| 2114 |
DESCRIPTION |
| 2115 |
"The current operational status of the VPL." |
| 2116 |
::= { atmVplEntry 3} |
| 2117 |
|
| 2118 |
atmVplLastChange OBJECT-TYPE |
| 2119 |
SYNTAX AtmVorXLastChange |
| 2120 |
MAX-ACCESS read-only |
| 2121 |
|
| 2122 |
|
| 2123 |
|
| 2124 |
<span class="grey">Tesink Standards Track [Page 38]</span></pre> |
| 2125 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-39" ></span> |
| 2126 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2127 |
|
| 2128 |
|
| 2129 |
STATUS current |
| 2130 |
DESCRIPTION |
| 2131 |
"The value of sysUpTime at the time this |
| 2132 |
VPL entered its current operational state." |
| 2133 |
::= { atmVplEntry 4 } |
| 2134 |
|
| 2135 |
atmVplReceiveTrafficDescrIndex OBJECT-TYPE |
| 2136 |
SYNTAX AtmTrafficDescrParamIndex |
| 2137 |
MAX-ACCESS read-create |
| 2138 |
STATUS current |
| 2139 |
DESCRIPTION |
| 2140 |
"The value of this object identifies the row |
| 2141 |
in the atmTrafficDescrParamTable which |
| 2142 |
applies to the receive direction of the VPL." |
| 2143 |
DEFVAL { 0 } |
| 2144 |
::= { atmVplEntry 5} |
| 2145 |
|
| 2146 |
atmVplTransmitTrafficDescrIndex OBJECT-TYPE |
| 2147 |
SYNTAX AtmTrafficDescrParamIndex |
| 2148 |
MAX-ACCESS read-create |
| 2149 |
STATUS current |
| 2150 |
DESCRIPTION |
| 2151 |
"The value of this object identifies the row |
| 2152 |
in the atmTrafficDescrParamTable which |
| 2153 |
applies to the transmit direction of the VPL." |
| 2154 |
DEFVAL { 0 } |
| 2155 |
::= { atmVplEntry 6} |
| 2156 |
|
| 2157 |
atmVplCrossConnectIdentifier OBJECT-TYPE |
| 2158 |
SYNTAX INTEGER (0..2147483647) |
| 2159 |
MAX-ACCESS read-only |
| 2160 |
STATUS current |
| 2161 |
DESCRIPTION |
| 2162 |
"This object is instantiated only for a VPL |
| 2163 |
which is cross-connected to other VPLs |
| 2164 |
that belong to the same VPC. All such |
| 2165 |
associated VPLs have the same value of this |
| 2166 |
object, and all their cross-connections are |
| 2167 |
identified either by entries that are indexed |
| 2168 |
by the same value of atmVpCrossConnectIndex in |
| 2169 |
the atmVpCrossConnectTable of this MIB module or by |
| 2170 |
the same value of the cross-connect index in |
| 2171 |
the cross-connect table for SVCs and Soft PVCs |
| 2172 |
(defined in a separate MIB module). |
| 2173 |
At no time should entries in these respective |
| 2174 |
cross-connect tables exist simultaneously |
| 2175 |
with the same cross-connect index value. |
| 2176 |
|
| 2177 |
|
| 2178 |
|
| 2179 |
|
| 2180 |
<span class="grey">Tesink Standards Track [Page 39]</span></pre> |
| 2181 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-40" ></span> |
| 2182 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2183 |
|
| 2184 |
|
| 2185 |
The value of this object is initialized by the |
| 2186 |
agent after the associated entries in the |
| 2187 |
atmVpCrossConnectTable have been created." |
| 2188 |
::= {atmVplEntry 7} |
| 2189 |
|
| 2190 |
atmVplRowStatus OBJECT-TYPE |
| 2191 |
SYNTAX RowStatus |
| 2192 |
MAX-ACCESS read-create |
| 2193 |
STATUS current |
| 2194 |
DESCRIPTION |
| 2195 |
"This object is used to create, delete |
| 2196 |
or modify a row in this table. |
| 2197 |
To create a new VCL, this object is |
| 2198 |
initially set to 'createAndWait' or |
| 2199 |
'createAndGo'. This object should not be |
| 2200 |
set to 'active' unless the following columnar |
| 2201 |
objects have been set to their desired value |
| 2202 |
in this row: |
| 2203 |
atmVplReceiveTrafficDescrIndex and |
| 2204 |
atmVplTransmitTrafficDescrIndex. |
| 2205 |
The DESCRIPTION of atmVplEntry provides |
| 2206 |
further guidance to row treatment in this table." |
| 2207 |
DEFVAL { createAndWait } |
| 2208 |
::= {atmVplEntry 8} |
| 2209 |
|
| 2210 |
atmVplCastType OBJECT-TYPE |
| 2211 |
SYNTAX AtmConnCastType |
| 2212 |
MAX-ACCESS read-create |
| 2213 |
STATUS current |
| 2214 |
DESCRIPTION |
| 2215 |
"The connection topology type." |
| 2216 |
DEFVAL { p2p } |
| 2217 |
::= {atmVplEntry 9} |
| 2218 |
|
| 2219 |
atmVplConnKind OBJECT-TYPE |
| 2220 |
SYNTAX AtmConnKind |
| 2221 |
MAX-ACCESS read-create |
| 2222 |
STATUS current |
| 2223 |
DESCRIPTION |
| 2224 |
"The use of call control." |
| 2225 |
DEFVAL { pvc } |
| 2226 |
::= {atmVplEntry 10} |
| 2227 |
|
| 2228 |
-- ATM Interface Virtual Channel Link (VCL) Table |
| 2229 |
|
| 2230 |
-- This table contains configuration and state |
| 2231 |
-- information of a bi-directional Virtual Channel |
| 2232 |
-- Link (VCL) at an ATM interface. |
| 2233 |
|
| 2234 |
|
| 2235 |
|
| 2236 |
<span class="grey">Tesink Standards Track [Page 40]</span></pre> |
| 2237 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-41" ></span> |
| 2238 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2239 |
|
| 2240 |
|
| 2241 |
-- This table can be used to create, delete or modify |
| 2242 |
-- a VCL that is terminated in an ATM host or switch. |
| 2243 |
-- This table can also be |
| 2244 |
-- used to create, delete or modify a VCL that is |
| 2245 |
-- cross-connected to another VCL. |
| 2246 |
|
| 2247 |
|
| 2248 |
-- The ATM Interface VCL Table |
| 2249 |
|
| 2250 |
|
| 2251 |
atmVclTable OBJECT-TYPE |
| 2252 |
SYNTAX SEQUENCE OF AtmVclEntry |
| 2253 |
MAX-ACCESS not-accessible |
| 2254 |
STATUS current |
| 2255 |
DESCRIPTION |
| 2256 |
"The Virtual Channel Link (VCL) table. A |
| 2257 |
bi-directional VCL is modeled as one entry |
| 2258 |
in this table. This table can be used for |
| 2259 |
PVCs, SVCs and Soft PVCs." |
| 2260 |
::= { atmMIBObjects 7} |
| 2261 |
|
| 2262 |
atmVclEntry OBJECT-TYPE |
| 2263 |
SYNTAX AtmVclEntry |
| 2264 |
MAX-ACCESS not-accessible |
| 2265 |
STATUS current |
| 2266 |
DESCRIPTION |
| 2267 |
"An entry in the VCL table. This entry is |
| 2268 |
used to model a bi-directional VCL. |
| 2269 |
To create a VCL at an ATM interface, |
| 2270 |
either of the following procedures are used: |
| 2271 |
|
| 2272 |
Negotiated VCL establishment |
| 2273 |
|
| 2274 |
(1) The management application creates |
| 2275 |
a VCL entry in the atmVclTable |
| 2276 |
by setting atmVclRowStatus to createAndWait(5). |
| 2277 |
This may fail for the following reasons: |
| 2278 |
- The selected VPI/VCI values are unavailable, |
| 2279 |
- The selected VPI/VCI values are in use. |
| 2280 |
Otherwise, the agent creates a row and |
| 2281 |
reserves the VPI/VCI values on that port. |
| 2282 |
|
| 2283 |
(2) The manager selects an existing row(s) in the |
| 2284 |
atmTrafficDescrParamTable, |
| 2285 |
thereby, selecting a set of self-consistent |
| 2286 |
ATM traffic parameters and the service category |
| 2287 |
for receive and transmit directions of the VCL. |
| 2288 |
|
| 2289 |
|
| 2290 |
|
| 2291 |
|
| 2292 |
<span class="grey">Tesink Standards Track [Page 41]</span></pre> |
| 2293 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-42" ></span> |
| 2294 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2295 |
|
| 2296 |
|
| 2297 |
(2a) If no suitable row(s) in the |
| 2298 |
atmTrafficDescrParamTable exists, |
| 2299 |
the manager must create a new row(s) |
| 2300 |
in that table. |
| 2301 |
|
| 2302 |
(2b) The manager characterizes the VCL's traffic |
| 2303 |
parameters through setting the |
| 2304 |
atmVclReceiveTrafficDescrIndex and the |
| 2305 |
atmVclTransmitTrafficDescrIndex values |
| 2306 |
in the VCL table, which point to the rows |
| 2307 |
containing desired ATM traffic parameter values |
| 2308 |
in the atmTrafficDescrParamTable. The agent |
| 2309 |
will check the availability of resources and |
| 2310 |
may refuse the request. |
| 2311 |
If the transmit and receive service categories |
| 2312 |
are inconsistent, the agent should refuse the |
| 2313 |
request. |
| 2314 |
|
| 2315 |
(3) The manager activates the VCL by setting the |
| 2316 |
the atmVclRowStatus to active(1) (for |
| 2317 |
requirements on this activation see the |
| 2318 |
description of atmVclRowStatus). |
| 2319 |
If this set is successful, the agent has |
| 2320 |
reserved the resources to satisfy the requested |
| 2321 |
traffic parameter values and the service category |
| 2322 |
for that VCL. |
| 2323 |
(4) If the VCL terminates a VCC in the ATM host |
| 2324 |
or switch, the manager turns on the |
| 2325 |
atmVclAdminStatus to up(1) to turn the VCL |
| 2326 |
traffic flow on. Otherwise, the |
| 2327 |
atmVcCrossConnectTable must be used |
| 2328 |
to cross-connect the VCL to another VCL(s) |
| 2329 |
in an ATM switch or network. |
| 2330 |
|
| 2331 |
One-Shot VCL Establishment |
| 2332 |
|
| 2333 |
A VCL may also be established in one step by a |
| 2334 |
set-request with all necessary VCL parameter |
| 2335 |
values and atmVclRowStatus set to createAndGo(4). |
| 2336 |
|
| 2337 |
In contrast to the negotiated VCL establishment |
| 2338 |
which allows for detailed error checking |
| 2339 |
(i.e., set errors are explicitly linked to |
| 2340 |
particular resource acquisition failures), |
| 2341 |
the one-shot VCL establishment |
| 2342 |
performs the setup on one operation but |
| 2343 |
does not have the advantage of step-wise |
| 2344 |
error checking. |
| 2345 |
|
| 2346 |
|
| 2347 |
|
| 2348 |
<span class="grey">Tesink Standards Track [Page 42]</span></pre> |
| 2349 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-43" ></span> |
| 2350 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2351 |
|
| 2352 |
|
| 2353 |
VCL Retirement |
| 2354 |
|
| 2355 |
A VCL is released by setting atmVclRowStatus to |
| 2356 |
destroy(6), and the agent may release all |
| 2357 |
associated resources." |
| 2358 |
INDEX {ifIndex, atmVclVpi, atmVclVci } |
| 2359 |
::= { atmVclTable 1} |
| 2360 |
|
| 2361 |
AtmVclEntry ::= SEQUENCE { |
| 2362 |
atmVclVpi AtmVpIdentifier, |
| 2363 |
atmVclVci AtmVcIdentifier, |
| 2364 |
atmVclAdminStatus AtmVorXAdminStatus, |
| 2365 |
atmVclOperStatus AtmVorXOperStatus, |
| 2366 |
atmVclLastChange AtmVorXLastChange, |
| 2367 |
atmVclReceiveTrafficDescrIndex |
| 2368 |
AtmTrafficDescrParamIndex, |
| 2369 |
atmVclTransmitTrafficDescrIndex |
| 2370 |
AtmTrafficDescrParamIndex, |
| 2371 |
atmVccAalType INTEGER, |
| 2372 |
atmVccAal5CpcsTransmitSduSize INTEGER, |
| 2373 |
atmVccAal5CpcsReceiveSduSize INTEGER, |
| 2374 |
atmVccAal5EncapsType INTEGER, |
| 2375 |
atmVclCrossConnectIdentifier INTEGER, |
| 2376 |
atmVclRowStatus RowStatus, |
| 2377 |
atmVclCastType AtmConnCastType, |
| 2378 |
atmVclConnKind AtmConnKind |
| 2379 |
} |
| 2380 |
|
| 2381 |
atmVclVpi OBJECT-TYPE |
| 2382 |
SYNTAX AtmVpIdentifier |
| 2383 |
MAX-ACCESS not-accessible |
| 2384 |
STATUS current |
| 2385 |
DESCRIPTION |
| 2386 |
"The VPI value of the VCL." |
| 2387 |
::= { atmVclEntry 1} |
| 2388 |
|
| 2389 |
atmVclVci OBJECT-TYPE |
| 2390 |
SYNTAX AtmVcIdentifier |
| 2391 |
MAX-ACCESS not-accessible |
| 2392 |
STATUS current |
| 2393 |
DESCRIPTION |
| 2394 |
"The VCI value of the VCL." |
| 2395 |
::= { atmVclEntry 2} |
| 2396 |
|
| 2397 |
atmVclAdminStatus OBJECT-TYPE |
| 2398 |
SYNTAX AtmVorXAdminStatus |
| 2399 |
MAX-ACCESS read-create |
| 2400 |
STATUS current |
| 2401 |
|
| 2402 |
|
| 2403 |
|
| 2404 |
<span class="grey">Tesink Standards Track [Page 43]</span></pre> |
| 2405 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-44" ></span> |
| 2406 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2407 |
|
| 2408 |
|
| 2409 |
DESCRIPTION |
| 2410 |
"This object is instanciated only for a VCL which |
| 2411 |
terminates a VCC (i.e., one which is NOT |
| 2412 |
cross-connected to other VCLs). Its value |
| 2413 |
specifies the desired administrative state of |
| 2414 |
the VCL." |
| 2415 |
DEFVAL { down } |
| 2416 |
::= { atmVclEntry 3} |
| 2417 |
|
| 2418 |
atmVclOperStatus OBJECT-TYPE |
| 2419 |
SYNTAX AtmVorXOperStatus |
| 2420 |
MAX-ACCESS read-only |
| 2421 |
STATUS current |
| 2422 |
DESCRIPTION |
| 2423 |
"The current operational status of the VCL." |
| 2424 |
::= { atmVclEntry 4} |
| 2425 |
|
| 2426 |
atmVclLastChange OBJECT-TYPE |
| 2427 |
SYNTAX AtmVorXLastChange |
| 2428 |
MAX-ACCESS read-only |
| 2429 |
STATUS current |
| 2430 |
DESCRIPTION |
| 2431 |
"The value of sysUpTime at the time this VCL |
| 2432 |
entered its current operational state." |
| 2433 |
::= { atmVclEntry 5 } |
| 2434 |
|
| 2435 |
atmVclReceiveTrafficDescrIndex OBJECT-TYPE |
| 2436 |
SYNTAX AtmTrafficDescrParamIndex |
| 2437 |
MAX-ACCESS read-create |
| 2438 |
STATUS current |
| 2439 |
DESCRIPTION |
| 2440 |
"The value of this object identifies the row |
| 2441 |
in the ATM Traffic Descriptor Table which |
| 2442 |
applies to the receive direction of this VCL." |
| 2443 |
DEFVAL { 0 } |
| 2444 |
::= { atmVclEntry 6} |
| 2445 |
|
| 2446 |
atmVclTransmitTrafficDescrIndex OBJECT-TYPE |
| 2447 |
SYNTAX AtmTrafficDescrParamIndex |
| 2448 |
MAX-ACCESS read-create |
| 2449 |
STATUS current |
| 2450 |
DESCRIPTION |
| 2451 |
"The value of this object identifies the row |
| 2452 |
of the ATM Traffic Descriptor Table which applies |
| 2453 |
to the transmit direction of this VCL." |
| 2454 |
DEFVAL { 0 } |
| 2455 |
::= { atmVclEntry 7} |
| 2456 |
|
| 2457 |
|
| 2458 |
|
| 2459 |
|
| 2460 |
<span class="grey">Tesink Standards Track [Page 44]</span></pre> |
| 2461 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-45" ></span> |
| 2462 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2463 |
|
| 2464 |
|
| 2465 |
atmVccAalType OBJECT-TYPE |
| 2466 |
SYNTAX INTEGER { |
| 2467 |
aal1(1), |
| 2468 |
aal34(2), |
| 2469 |
aal5(3), |
| 2470 |
other(4), |
| 2471 |
unknown(5), |
| 2472 |
aal2(6) |
| 2473 |
} |
| 2474 |
MAX-ACCESS read-create |
| 2475 |
STATUS current |
| 2476 |
DESCRIPTION |
| 2477 |
"An instance of this object only exists when the |
| 2478 |
local VCL end-point is also the VCC end-point, |
| 2479 |
and AAL is in use. |
| 2480 |
The type of AAL used on this VCC. |
| 2481 |
The AAL type includes AAL1, AAL2, AAL3/4, |
| 2482 |
and AAL5. The other(4) may be user-defined |
| 2483 |
AAL type. The unknown type indicates that |
| 2484 |
the AAL type cannot be determined." |
| 2485 |
DEFVAL { aal5 } |
| 2486 |
::= { atmVclEntry 8 } |
| 2487 |
|
| 2488 |
atmVccAal5CpcsTransmitSduSize OBJECT-TYPE |
| 2489 |
SYNTAX INTEGER (1..65535) |
| 2490 |
MAX-ACCESS read-create |
| 2491 |
STATUS current |
| 2492 |
DESCRIPTION |
| 2493 |
"An instance of this object only exists when the |
| 2494 |
local VCL end-point is also the VCC end-point, |
| 2495 |
and AAL5 is in use. |
| 2496 |
The maximum AAL5 CPCS SDU size in octets that is |
| 2497 |
supported on the transmit direction of this VCC." |
| 2498 |
DEFVAL { 9188 } |
| 2499 |
::= { atmVclEntry 9 } |
| 2500 |
|
| 2501 |
atmVccAal5CpcsReceiveSduSize OBJECT-TYPE |
| 2502 |
SYNTAX INTEGER (1..65535) |
| 2503 |
MAX-ACCESS read-create |
| 2504 |
STATUS current |
| 2505 |
DESCRIPTION |
| 2506 |
"An instance of this object only exists when the |
| 2507 |
local VCL end-point is also the VCC end-point, |
| 2508 |
and AAL5 is in use. |
| 2509 |
The maximum AAL5 CPCS SDU size in octets that is |
| 2510 |
supported on the receive direction of this VCC." |
| 2511 |
DEFVAL { 9188 } |
| 2512 |
::= { atmVclEntry 10 } |
| 2513 |
|
| 2514 |
|
| 2515 |
|
| 2516 |
<span class="grey">Tesink Standards Track [Page 45]</span></pre> |
| 2517 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-46" ></span> |
| 2518 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2519 |
|
| 2520 |
|
| 2521 |
atmVccAal5EncapsType OBJECT-TYPE |
| 2522 |
SYNTAX INTEGER { |
| 2523 |
vcMultiplexRoutedProtocol(1), |
| 2524 |
vcMultiplexBridgedProtocol8023(2), |
| 2525 |
vcMultiplexBridgedProtocol8025(3), |
| 2526 |
vcMultiplexBridgedProtocol8026(4), |
| 2527 |
vcMultiplexLANemulation8023(5), |
| 2528 |
vcMultiplexLANemulation8025(6), |
| 2529 |
llcEncapsulation(7), |
| 2530 |
multiprotocolFrameRelaySscs(8), |
| 2531 |
other(9), |
| 2532 |
unknown(10) |
| 2533 |
} |
| 2534 |
MAX-ACCESS read-create |
| 2535 |
STATUS current |
| 2536 |
DESCRIPTION |
| 2537 |
"An instance of this object only exists when the |
| 2538 |
local VCL end-point is also the VCC end-point, |
| 2539 |
and AAL5 is in use. |
| 2540 |
The type of data encapsulation used over |
| 2541 |
the AAL5 SSCS layer. The definitions reference |
| 2542 |
<a href="./rfc1483">RFC 1483</a> Multiprotocol Encapsulation |
| 2543 |
over ATM AAL5 and to the ATM Forum |
| 2544 |
LAN Emulation specification." |
| 2545 |
DEFVAL { llcEncapsulation } |
| 2546 |
::= { atmVclEntry 11 } |
| 2547 |
|
| 2548 |
atmVclCrossConnectIdentifier OBJECT-TYPE |
| 2549 |
SYNTAX INTEGER (0..2147483647) |
| 2550 |
MAX-ACCESS read-only |
| 2551 |
STATUS current |
| 2552 |
DESCRIPTION |
| 2553 |
"This object is instantiated only for a VCL |
| 2554 |
which is cross-connected to other VCLs |
| 2555 |
that belong to the same VCC. All such |
| 2556 |
associated VCLs have the same value of this |
| 2557 |
object, and all their cross-connections are |
| 2558 |
identified either by entries that are indexed |
| 2559 |
by the same value of atmVcCrossConnectIndex in |
| 2560 |
the atmVcCrossConnectTable of this MIB module or by |
| 2561 |
the same value of the cross-connect index in |
| 2562 |
the cross-connect table for SVCs and Soft PVCs |
| 2563 |
(defined in a separate MIB module). |
| 2564 |
|
| 2565 |
At no time should entries in these respective |
| 2566 |
cross-connect tables exist simultaneously |
| 2567 |
with the same cross-connect index value. |
| 2568 |
|
| 2569 |
|
| 2570 |
|
| 2571 |
|
| 2572 |
<span class="grey">Tesink Standards Track [Page 46]</span></pre> |
| 2573 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-47" ></span> |
| 2574 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2575 |
|
| 2576 |
|
| 2577 |
The value of this object is initialized by the |
| 2578 |
agent after the associated entries in the |
| 2579 |
atmVcCrossConnectTable have been created." |
| 2580 |
::= {atmVclEntry 12} |
| 2581 |
|
| 2582 |
atmVclRowStatus OBJECT-TYPE |
| 2583 |
SYNTAX RowStatus |
| 2584 |
MAX-ACCESS read-create |
| 2585 |
STATUS current |
| 2586 |
DESCRIPTION |
| 2587 |
"This object is used to create, delete or |
| 2588 |
modify a row in this table. To create |
| 2589 |
a new VCL, this object is initially set |
| 2590 |
to 'createAndWait' or 'createAndGo'. |
| 2591 |
This object should not be |
| 2592 |
set to 'active' unless the following columnar |
| 2593 |
objects have been set to their desired value |
| 2594 |
in this row: |
| 2595 |
atmVclReceiveTrafficDescrIndex, |
| 2596 |
atmVclTransmitTrafficDescrIndex. |
| 2597 |
In addition, if the local VCL end-point |
| 2598 |
is also the VCC end-point: |
| 2599 |
atmVccAalType. |
| 2600 |
In addition, for AAL5 connections only: |
| 2601 |
atmVccAal5CpcsTransmitSduSize, |
| 2602 |
atmVccAal5CpcsReceiveSduSize, and |
| 2603 |
atmVccAal5EncapsType. (The existence |
| 2604 |
of these objects imply the AAL connection type.). |
| 2605 |
The DESCRIPTION of atmVclEntry provides |
| 2606 |
further guidance to row treatment in this table." |
| 2607 |
DEFVAL { createAndWait } |
| 2608 |
::= {atmVclEntry 13} |
| 2609 |
|
| 2610 |
atmVclCastType OBJECT-TYPE |
| 2611 |
SYNTAX AtmConnCastType |
| 2612 |
MAX-ACCESS read-create |
| 2613 |
STATUS current |
| 2614 |
DESCRIPTION |
| 2615 |
"The connection topology type." |
| 2616 |
DEFVAL { p2p } |
| 2617 |
::= {atmVclEntry 14} |
| 2618 |
|
| 2619 |
|
| 2620 |
atmVclConnKind OBJECT-TYPE |
| 2621 |
SYNTAX AtmConnKind |
| 2622 |
MAX-ACCESS read-create |
| 2623 |
STATUS current |
| 2624 |
DESCRIPTION |
| 2625 |
|
| 2626 |
|
| 2627 |
|
| 2628 |
<span class="grey">Tesink Standards Track [Page 47]</span></pre> |
| 2629 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-48" ></span> |
| 2630 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2631 |
|
| 2632 |
|
| 2633 |
"The use of call control." |
| 2634 |
DEFVAL { pvc } |
| 2635 |
::= {atmVclEntry 15} |
| 2636 |
|
| 2637 |
|
| 2638 |
-- ATM Virtual Path (VP) Cross Connect Table |
| 2639 |
|
| 2640 |
-- This table contains configuration and state |
| 2641 |
-- information of point-to-point, |
| 2642 |
-- point-to-multipoint, or multipoint-to-multipoint |
| 2643 |
-- VP cross-connects for PVCs. |
| 2644 |
|
| 2645 |
-- This table has read-create access and can be used |
| 2646 |
-- to cross-connect the VPLs together in an ATM switch |
| 2647 |
-- or network. The atmVpCrossConnectIndex |
| 2648 |
-- is used to associate the related |
| 2649 |
-- VPLs that are cross-connected together. |
| 2650 |
|
| 2651 |
-- The ATM VP Cross Connect Table |
| 2652 |
-- models each bi-directional VPC |
| 2653 |
-- cross-connect as a set of entries in |
| 2654 |
-- the atmVpCrossConnectTable. A |
| 2655 |
-- point-to-point VPC cross-connect is modeled |
| 2656 |
-- as one entry; a point-to-multipoint (N leafs) VPC |
| 2657 |
-- cross-connect as N entries in this table; and |
| 2658 |
-- a multipoint-to-multipoint (N parties) VPC cross- |
| 2659 |
-- connect as N(N-1)/2 entries in this table. |
| 2660 |
-- In the latter cases, all the N (or N(N-1)/2) entries |
| 2661 |
-- are associated with a single VPC cross-connect by |
| 2662 |
-- having the same value of atmVpCrossConnectIndex. |
| 2663 |
|
| 2664 |
|
| 2665 |
-- _________________________________________ |
| 2666 |
-- | | |
| 2667 |
-- Low | ATM Switch or Network | High |
| 2668 |
-- port| | port |
| 2669 |
-- _____|>> from low to high VPC traffic flow >>|______ |
| 2670 |
-- |<< from high to low VPC traffic flow <<| |
| 2671 |
-- | | |
| 2672 |
-- |_______________________________________| |
| 2673 |
-- |
| 2674 |
|
| 2675 |
-- The terms low and high are chosen to represent |
| 2676 |
-- numerical ordering of the two interfaces associated |
| 2677 |
-- with a VPC cross-connect. That is, the ATM interface |
| 2678 |
-- with the lower value of ifIndex is termed 'low', |
| 2679 |
-- while the other ATM interface associated with the |
| 2680 |
-- VPC cross-connect is termed 'high'. This terminology |
| 2681 |
|
| 2682 |
|
| 2683 |
|
| 2684 |
<span class="grey">Tesink Standards Track [Page 48]</span></pre> |
| 2685 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-49" ></span> |
| 2686 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2687 |
|
| 2688 |
|
| 2689 |
-- is used to provide directional information; for |
| 2690 |
-- example, the atmVpCrossConnectL2HOperStatus applies |
| 2691 |
-- to the low->high direction, and |
| 2692 |
-- atmVpCrossConnectH2LOperStatus applies to the |
| 2693 |
-- high->low direction, as illustrated above. |
| 2694 |
|
| 2695 |
|
| 2696 |
|
| 2697 |
|
| 2698 |
atmVpCrossConnectIndexNext OBJECT-TYPE |
| 2699 |
SYNTAX INTEGER (0..2147483647) |
| 2700 |
MAX-ACCESS read-only |
| 2701 |
STATUS current |
| 2702 |
DESCRIPTION |
| 2703 |
"This object contains an appropriate value to |
| 2704 |
be used for atmVpCrossConnectIndex when creating |
| 2705 |
entries in the atmVpCrossConnectTable. The value |
| 2706 |
0 indicates that no unassigned entries are |
| 2707 |
available. To obtain the atmVpCrossConnectIndex |
| 2708 |
value for a new entry, the manager issues a |
| 2709 |
management protocol retrieval operation to obtain |
| 2710 |
the current value of this object. After each |
| 2711 |
retrieval, the agent should modify the value to |
| 2712 |
the next unassigned index. |
| 2713 |
After a manager retrieves a value the agent will |
| 2714 |
determine through its local policy when this index |
| 2715 |
value will be made available for reuse." |
| 2716 |
::= { atmMIBObjects 8 } |
| 2717 |
|
| 2718 |
|
| 2719 |
-- The ATM VP Cross Connect Table |
| 2720 |
|
| 2721 |
|
| 2722 |
atmVpCrossConnectTable OBJECT-TYPE |
| 2723 |
SYNTAX SEQUENCE OF AtmVpCrossConnectEntry |
| 2724 |
MAX-ACCESS not-accessible |
| 2725 |
STATUS current |
| 2726 |
DESCRIPTION |
| 2727 |
"The ATM VP Cross Connect table for PVCs. |
| 2728 |
An entry in this table models two |
| 2729 |
cross-connected VPLs. |
| 2730 |
Each VPL must have its atmConnKind set |
| 2731 |
to pvc(1)." |
| 2732 |
::= { atmMIBObjects 9 } |
| 2733 |
|
| 2734 |
|
| 2735 |
atmVpCrossConnectEntry OBJECT-TYPE |
| 2736 |
SYNTAX AtmVpCrossConnectEntry |
| 2737 |
|
| 2738 |
|
| 2739 |
|
| 2740 |
<span class="grey">Tesink Standards Track [Page 49]</span></pre> |
| 2741 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-50" ></span> |
| 2742 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2743 |
|
| 2744 |
|
| 2745 |
MAX-ACCESS not-accessible |
| 2746 |
STATUS current |
| 2747 |
DESCRIPTION |
| 2748 |
"An entry in the ATM VP Cross Connect table. |
| 2749 |
This entry is used to model a bi-directional |
| 2750 |
ATM VP cross-connect which cross-connects |
| 2751 |
two VPLs. |
| 2752 |
|
| 2753 |
Step-wise Procedures to set up a VP Cross-connect |
| 2754 |
|
| 2755 |
Once the entries in the atmVplTable are created, |
| 2756 |
the following procedures are used |
| 2757 |
to cross-connect the VPLs together. |
| 2758 |
|
| 2759 |
(1) The manager obtains a unique |
| 2760 |
atmVpCrossConnectIndex by reading the |
| 2761 |
atmVpCrossConnectIndexNext object. |
| 2762 |
|
| 2763 |
(2) Next, the manager creates a set of one |
| 2764 |
or more rows in the ATM VP Cross Connect |
| 2765 |
Table, one for each cross-connection between |
| 2766 |
two VPLs. Each row is indexed by the ATM |
| 2767 |
interface port numbers and VPI values of the |
| 2768 |
two ends of that cross-connection. |
| 2769 |
This set of rows specifies the topology of the |
| 2770 |
VPC cross-connect and is identified by a single |
| 2771 |
value of atmVpCrossConnectIndex. |
| 2772 |
|
| 2773 |
Negotiated VP Cross-Connect Establishment |
| 2774 |
|
| 2775 |
(2a) The manager creates a row in this table by |
| 2776 |
setting atmVpCrossConnectRowStatus to |
| 2777 |
createAndWait(5). The agent checks the |
| 2778 |
requested topology and the mutual sanity of |
| 2779 |
the ATM traffic parameters and |
| 2780 |
service categories, i.e., the row creation |
| 2781 |
fails if: |
| 2782 |
- the requested topology is incompatible with |
| 2783 |
associated values of atmVplCastType, |
| 2784 |
- the requested topology is not supported |
| 2785 |
by the agent, |
| 2786 |
- the traffic/service category parameter values |
| 2787 |
associated with the requested row are |
| 2788 |
incompatible with those of already existing |
| 2789 |
rows for this VP cross-connect. |
| 2790 |
[For example, for setting up |
| 2791 |
a point-to-point VP cross-connect, the |
| 2792 |
ATM traffic parameters in the receive direction |
| 2793 |
|
| 2794 |
|
| 2795 |
|
| 2796 |
<span class="grey">Tesink Standards Track [Page 50]</span></pre> |
| 2797 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-51" ></span> |
| 2798 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2799 |
|
| 2800 |
|
| 2801 |
of a VPL at the low end of the cross-connect |
| 2802 |
must equal to the traffic parameters in the |
| 2803 |
transmit direction of the other VPL at the |
| 2804 |
high end of the cross-connect, |
| 2805 |
otherwise, the row creation fails.] |
| 2806 |
The agent also checks for internal errors |
| 2807 |
in building the cross-connect. |
| 2808 |
|
| 2809 |
The atmVpCrossConnectIndex values in the |
| 2810 |
corresponding atmVplTable rows are filled |
| 2811 |
in by the agent at this point. |
| 2812 |
|
| 2813 |
(2b) The manager promotes the row in the |
| 2814 |
atmVpCrossConnectTable by setting |
| 2815 |
atmVpCrossConnectRowStatus to active(1). If |
| 2816 |
this set is successful, the agent has reserved |
| 2817 |
the resources specified by the ATM traffic |
| 2818 |
parameter and Service category values |
| 2819 |
for each direction of the VP cross-connect |
| 2820 |
in an ATM switch or network. |
| 2821 |
|
| 2822 |
(3) The manager sets the |
| 2823 |
atmVpCrossConnectAdminStatus to up(1) in all |
| 2824 |
rows of this VP cross-connect to turn the |
| 2825 |
traffic flow on. |
| 2826 |
|
| 2827 |
|
| 2828 |
One-Shot VP Cross-Connect Establishment |
| 2829 |
|
| 2830 |
A VP cross-connect may also be established in |
| 2831 |
one step by a set-request with all necessary |
| 2832 |
parameter values and atmVpCrossConnectRowStatus |
| 2833 |
set to createAndGo(4). |
| 2834 |
|
| 2835 |
In contrast to the negotiated VP cross-connect |
| 2836 |
establishment which allows for detailed error |
| 2837 |
checking (i.e., set errors are explicitly linked |
| 2838 |
to particular resource acquisition failures), |
| 2839 |
the one-shot VP cross-connect establishment |
| 2840 |
performs the setup on one operation but does not |
| 2841 |
have the advantage of step-wise error checking. |
| 2842 |
|
| 2843 |
VP Cross-Connect Retirement |
| 2844 |
|
| 2845 |
A VP cross-connect identified by a particular |
| 2846 |
value of atmVpCrossConnectIndex is released by: |
| 2847 |
|
| 2848 |
(1) Setting atmVpCrossConnectRowStatus of all |
| 2849 |
|
| 2850 |
|
| 2851 |
|
| 2852 |
<span class="grey">Tesink Standards Track [Page 51]</span></pre> |
| 2853 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-52" ></span> |
| 2854 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2855 |
|
| 2856 |
|
| 2857 |
rows identified by this value of |
| 2858 |
atmVpCrossConnectIndex to destroy(6). |
| 2859 |
The agent may release all |
| 2860 |
associated resources, and the |
| 2861 |
atmVpCrossConnectIndex values in the |
| 2862 |
corresponding atmVplTable row are removed. |
| 2863 |
Note that a situation when only a subset of |
| 2864 |
the associated rows are deleted corresponds |
| 2865 |
to a VP topology change. |
| 2866 |
|
| 2867 |
(2) After deletion of the appropriate |
| 2868 |
atmVpCrossConnectEntries, the manager may |
| 2869 |
set atmVplRowStatus to destroy(6) the |
| 2870 |
associated VPLs. The agent releases |
| 2871 |
the resources and removes the associated |
| 2872 |
rows in the atmVplTable. |
| 2873 |
|
| 2874 |
VP Cross-connect Reconfiguration |
| 2875 |
|
| 2876 |
At the discretion of the agent, a VP |
| 2877 |
cross-connect may be reconfigured by |
| 2878 |
adding and/or deleting leafs to/from |
| 2879 |
the VP topology as per the VP cross-connect |
| 2880 |
establishment/retirement procedures. |
| 2881 |
Reconfiguration of traffic/service category parameter |
| 2882 |
values requires release of the VP cross-connect |
| 2883 |
before those parameter values may by changed |
| 2884 |
for individual VPLs." |
| 2885 |
INDEX { atmVpCrossConnectIndex, |
| 2886 |
atmVpCrossConnectLowIfIndex, |
| 2887 |
atmVpCrossConnectLowVpi, |
| 2888 |
atmVpCrossConnectHighIfIndex, |
| 2889 |
atmVpCrossConnectHighVpi } |
| 2890 |
::= { atmVpCrossConnectTable 1 } |
| 2891 |
|
| 2892 |
AtmVpCrossConnectEntry ::= SEQUENCE { |
| 2893 |
atmVpCrossConnectIndex INTEGER, |
| 2894 |
atmVpCrossConnectLowIfIndex InterfaceIndex, |
| 2895 |
atmVpCrossConnectLowVpi AtmVpIdentifier, |
| 2896 |
atmVpCrossConnectHighIfIndex InterfaceIndex, |
| 2897 |
atmVpCrossConnectHighVpi AtmVpIdentifier, |
| 2898 |
atmVpCrossConnectAdminStatus AtmVorXAdminStatus, |
| 2899 |
atmVpCrossConnectL2HOperStatus AtmVorXOperStatus, |
| 2900 |
atmVpCrossConnectH2LOperStatus AtmVorXOperStatus, |
| 2901 |
atmVpCrossConnectL2HLastChange AtmVorXLastChange, |
| 2902 |
atmVpCrossConnectH2LLastChange AtmVorXLastChange, |
| 2903 |
atmVpCrossConnectRowStatus RowStatus |
| 2904 |
} |
| 2905 |
|
| 2906 |
|
| 2907 |
|
| 2908 |
<span class="grey">Tesink Standards Track [Page 52]</span></pre> |
| 2909 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-53" ></span> |
| 2910 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2911 |
|
| 2912 |
|
| 2913 |
atmVpCrossConnectIndex OBJECT-TYPE |
| 2914 |
SYNTAX INTEGER (1..2147483647) |
| 2915 |
MAX-ACCESS not-accessible |
| 2916 |
STATUS current |
| 2917 |
DESCRIPTION |
| 2918 |
"A unique value to identify this VP cross-connect. |
| 2919 |
For each VPL associated with this cross-connect, |
| 2920 |
the agent reports this cross-connect index value |
| 2921 |
in the atmVplCrossConnectIdentifier attribute of |
| 2922 |
the corresponding atmVplTable entries." |
| 2923 |
::= { atmVpCrossConnectEntry 1 } |
| 2924 |
|
| 2925 |
atmVpCrossConnectLowIfIndex OBJECT-TYPE |
| 2926 |
SYNTAX InterfaceIndex |
| 2927 |
MAX-ACCESS not-accessible |
| 2928 |
STATUS current |
| 2929 |
DESCRIPTION |
| 2930 |
"The ifIndex value of the ATM interface for |
| 2931 |
this VP cross-connect. The term low implies |
| 2932 |
that this ATM interface has the numerically lower |
| 2933 |
ifIndex value than the other ATM interface |
| 2934 |
identified in the same atmVpCrossConnectEntry." |
| 2935 |
::= { atmVpCrossConnectEntry 2 } |
| 2936 |
|
| 2937 |
atmVpCrossConnectLowVpi OBJECT-TYPE |
| 2938 |
SYNTAX AtmVpIdentifier |
| 2939 |
MAX-ACCESS not-accessible |
| 2940 |
STATUS current |
| 2941 |
DESCRIPTION |
| 2942 |
"The VPI value at the ATM interface |
| 2943 |
associated with the VP cross-connect that is |
| 2944 |
identified by atmVpCrossConnectLowIfIndex." |
| 2945 |
::= { atmVpCrossConnectEntry 3 } |
| 2946 |
|
| 2947 |
atmVpCrossConnectHighIfIndex OBJECT-TYPE |
| 2948 |
SYNTAX InterfaceIndex |
| 2949 |
MAX-ACCESS not-accessible |
| 2950 |
STATUS current |
| 2951 |
DESCRIPTION |
| 2952 |
"The ifIndex value of the ATM interface for |
| 2953 |
this VP cross-connect. The term high implies that |
| 2954 |
this ATM interface has the numerically higher |
| 2955 |
ifIndex value than the other ATM interface |
| 2956 |
identified in the same atmVpCrossConnectEntry." |
| 2957 |
::= { atmVpCrossConnectEntry 4 } |
| 2958 |
|
| 2959 |
atmVpCrossConnectHighVpi OBJECT-TYPE |
| 2960 |
SYNTAX AtmVpIdentifier |
| 2961 |
|
| 2962 |
|
| 2963 |
|
| 2964 |
<span class="grey">Tesink Standards Track [Page 53]</span></pre> |
| 2965 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-54" ></span> |
| 2966 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 2967 |
|
| 2968 |
|
| 2969 |
MAX-ACCESS not-accessible |
| 2970 |
STATUS current |
| 2971 |
DESCRIPTION |
| 2972 |
"The VPI value at the ATM interface |
| 2973 |
associated with the VP cross-connect that is |
| 2974 |
identified by atmVpCrossConnectHighIfIndex." |
| 2975 |
::= { atmVpCrossConnectEntry 5 } |
| 2976 |
|
| 2977 |
atmVpCrossConnectAdminStatus OBJECT-TYPE |
| 2978 |
SYNTAX AtmVorXAdminStatus |
| 2979 |
MAX-ACCESS read-create |
| 2980 |
STATUS current |
| 2981 |
DESCRIPTION |
| 2982 |
"The desired administrative status of this |
| 2983 |
bi-directional VP cross-connect." |
| 2984 |
DEFVAL { down } |
| 2985 |
::= { atmVpCrossConnectEntry 6 } |
| 2986 |
|
| 2987 |
atmVpCrossConnectL2HOperStatus OBJECT-TYPE |
| 2988 |
SYNTAX AtmVorXOperStatus |
| 2989 |
MAX-ACCESS read-only |
| 2990 |
STATUS current |
| 2991 |
DESCRIPTION |
| 2992 |
"The operational status of the VP cross-connect |
| 2993 |
in one direction; (i.e., from the low to |
| 2994 |
high direction)." |
| 2995 |
::= { atmVpCrossConnectEntry 7 } |
| 2996 |
|
| 2997 |
atmVpCrossConnectH2LOperStatus OBJECT-TYPE |
| 2998 |
SYNTAX AtmVorXOperStatus |
| 2999 |
MAX-ACCESS read-only |
| 3000 |
STATUS current |
| 3001 |
DESCRIPTION |
| 3002 |
"The operational status of the VP cross-connect |
| 3003 |
in one direction; (i.e., from the high to |
| 3004 |
low direction)." |
| 3005 |
::= { atmVpCrossConnectEntry 8 } |
| 3006 |
|
| 3007 |
atmVpCrossConnectL2HLastChange OBJECT-TYPE |
| 3008 |
SYNTAX AtmVorXLastChange |
| 3009 |
MAX-ACCESS read-only |
| 3010 |
STATUS current |
| 3011 |
DESCRIPTION |
| 3012 |
"The value of sysUpTime at the time this |
| 3013 |
VP cross-connect entered its current operational |
| 3014 |
state in the low to high direction." |
| 3015 |
::= { atmVpCrossConnectEntry 9 } |
| 3016 |
|
| 3017 |
|
| 3018 |
|
| 3019 |
|
| 3020 |
<span class="grey">Tesink Standards Track [Page 54]</span></pre> |
| 3021 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-55" ></span> |
| 3022 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3023 |
|
| 3024 |
|
| 3025 |
atmVpCrossConnectH2LLastChange OBJECT-TYPE |
| 3026 |
SYNTAX AtmVorXLastChange |
| 3027 |
MAX-ACCESS read-only |
| 3028 |
STATUS current |
| 3029 |
DESCRIPTION |
| 3030 |
"The value of sysUpTime at the time this |
| 3031 |
VP cross-connect entered its current operational |
| 3032 |
in the high to low direction." |
| 3033 |
::= { atmVpCrossConnectEntry 10 } |
| 3034 |
|
| 3035 |
atmVpCrossConnectRowStatus OBJECT-TYPE |
| 3036 |
SYNTAX RowStatus |
| 3037 |
MAX-ACCESS read-create |
| 3038 |
STATUS current |
| 3039 |
DESCRIPTION |
| 3040 |
"The status of this entry in the |
| 3041 |
atmVpCrossConnectTable. This object is used to |
| 3042 |
create a cross-connect for cross-connecting |
| 3043 |
VPLs which are created using the atmVplTable |
| 3044 |
or to change or delete an existing cross-connect. |
| 3045 |
This object must be initially set |
| 3046 |
to `createAndWait' or 'createAndGo'. |
| 3047 |
To turn on a VP cross-connect, |
| 3048 |
the atmVpCrossConnectAdminStatus |
| 3049 |
is set to `up'." |
| 3050 |
DEFVAL { createAndWait } |
| 3051 |
::= { atmVpCrossConnectEntry 11 } |
| 3052 |
|
| 3053 |
|
| 3054 |
-- ATM Virtual Channel (VC) Cross Connect Table |
| 3055 |
|
| 3056 |
-- This table contains configuration and state |
| 3057 |
-- information of point-to-point, |
| 3058 |
-- point-to-multipoint or multipoint-to-multipoint |
| 3059 |
-- VC cross-connects for PVCs. |
| 3060 |
|
| 3061 |
-- This table has read-create access and is used |
| 3062 |
-- to cross-connect the VCLs together in an ATM switch |
| 3063 |
-- or network that belong to a VC connection. |
| 3064 |
-- The atmVcCrossConnectIndex is used to associate |
| 3065 |
-- the related VCLs that are cross-connected together. |
| 3066 |
|
| 3067 |
|
| 3068 |
|
| 3069 |
-- The model using step-wise procedures described for setting |
| 3070 |
-- up a VP cross-connect is also used for setting up |
| 3071 |
-- a VC cross-connect. |
| 3072 |
|
| 3073 |
|
| 3074 |
|
| 3075 |
|
| 3076 |
<span class="grey">Tesink Standards Track [Page 55]</span></pre> |
| 3077 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-56" ></span> |
| 3078 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3079 |
|
| 3080 |
|
| 3081 |
atmVcCrossConnectIndexNext OBJECT-TYPE |
| 3082 |
SYNTAX INTEGER (0..2147483647) |
| 3083 |
MAX-ACCESS read-only |
| 3084 |
STATUS current |
| 3085 |
DESCRIPTION |
| 3086 |
"This object contains an appropriate value to |
| 3087 |
be used for atmVcCrossConnectIndex when creating |
| 3088 |
entries in the atmVcCrossConnectTable. The value |
| 3089 |
0 indicates that no unassigned entries are |
| 3090 |
available. To obtain the atmVcCrossConnectIndex |
| 3091 |
value for a new entry, the manager issues a |
| 3092 |
management protocol retrieval operation to obtain |
| 3093 |
the current value of this object. After each |
| 3094 |
retrieval, the agent should modify the value to |
| 3095 |
the next unassigned index. |
| 3096 |
After a manager retrieves a value the agent will |
| 3097 |
determine through its local policy when this index |
| 3098 |
value will be made available for reuse." |
| 3099 |
::= { atmMIBObjects 10 } |
| 3100 |
|
| 3101 |
|
| 3102 |
-- The ATM VC Cross Connect Table |
| 3103 |
|
| 3104 |
|
| 3105 |
atmVcCrossConnectTable OBJECT-TYPE |
| 3106 |
SYNTAX SEQUENCE OF AtmVcCrossConnectEntry |
| 3107 |
MAX-ACCESS not-accessible |
| 3108 |
STATUS current |
| 3109 |
DESCRIPTION |
| 3110 |
"The ATM VC Cross Connect table for PVCs. |
| 3111 |
An entry in this table models two |
| 3112 |
cross-connected VCLs. |
| 3113 |
Each VCL must have its atmConnKind set |
| 3114 |
to pvc(1)." |
| 3115 |
::= { atmMIBObjects 11 } |
| 3116 |
|
| 3117 |
|
| 3118 |
atmVcCrossConnectEntry OBJECT-TYPE |
| 3119 |
SYNTAX AtmVcCrossConnectEntry |
| 3120 |
MAX-ACCESS not-accessible |
| 3121 |
STATUS current |
| 3122 |
DESCRIPTION |
| 3123 |
"An entry in the ATM VC Cross Connect table. |
| 3124 |
This entry is used to model a bi-directional ATM |
| 3125 |
VC cross-connect cross-connecting two end points. |
| 3126 |
|
| 3127 |
Step-wise Procedures to set up a VC Cross-connect |
| 3128 |
|
| 3129 |
|
| 3130 |
|
| 3131 |
|
| 3132 |
<span class="grey">Tesink Standards Track [Page 56]</span></pre> |
| 3133 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-57" ></span> |
| 3134 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3135 |
|
| 3136 |
|
| 3137 |
Once the entries in the atmVclTable are created, |
| 3138 |
the following procedures are used |
| 3139 |
to cross-connect the VCLs together to |
| 3140 |
form a VCC segment. |
| 3141 |
|
| 3142 |
(1) The manager obtains a unique |
| 3143 |
atmVcCrossConnectIndex by reading the |
| 3144 |
atmVcCrossConnectIndexNext object. |
| 3145 |
|
| 3146 |
(2) Next, the manager creates a set of one |
| 3147 |
or more rows in the ATM VC Cross Connect |
| 3148 |
Table, one for each cross-connection between |
| 3149 |
two VCLs. Each row is indexed by the ATM |
| 3150 |
interface port numbers and VPI/VCI values of |
| 3151 |
the two ends of that cross-connection. |
| 3152 |
This set of rows specifies the topology of the |
| 3153 |
VCC cross-connect and is identified by a single |
| 3154 |
value of atmVcCrossConnectIndex. |
| 3155 |
|
| 3156 |
Negotiated VC Cross-Connect Establishment |
| 3157 |
|
| 3158 |
(2a) The manager creates a row in this table by |
| 3159 |
setting atmVcCrossConnectRowStatus to |
| 3160 |
createAndWait(5). The agent checks the |
| 3161 |
requested topology and the mutual sanity of |
| 3162 |
the ATM traffic parameters and |
| 3163 |
service categories, i.e., the row creation |
| 3164 |
fails if: |
| 3165 |
- the requested topology is incompatible with |
| 3166 |
associated values of atmVclCastType, |
| 3167 |
- the requested topology is not supported |
| 3168 |
by the agent, |
| 3169 |
- the traffic/service category parameter values |
| 3170 |
associated with the requested row are |
| 3171 |
incompatible with those of already existing |
| 3172 |
rows for this VC cross-connect. |
| 3173 |
[For example, for setting up |
| 3174 |
a point-to-point VC cross-connect, the |
| 3175 |
ATM traffic parameters in the receive direction |
| 3176 |
of a VCL at the low end of the cross-connect |
| 3177 |
must equal to the traffic parameters in the |
| 3178 |
transmit direction of the other VCL at the |
| 3179 |
high end of the cross-connect, |
| 3180 |
otherwise, the row creation fails.] |
| 3181 |
The agent also checks for internal errors |
| 3182 |
in building the cross-connect. |
| 3183 |
|
| 3184 |
The atmVcCrossConnectIndex values in the |
| 3185 |
|
| 3186 |
|
| 3187 |
|
| 3188 |
<span class="grey">Tesink Standards Track [Page 57]</span></pre> |
| 3189 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-58" ></span> |
| 3190 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3191 |
|
| 3192 |
|
| 3193 |
corresponding atmVclTable rows are filled |
| 3194 |
in by the agent at this point. |
| 3195 |
|
| 3196 |
(2b) The manager promotes the row in the |
| 3197 |
atmVcCrossConnectTable by setting |
| 3198 |
atmVcCrossConnectRowStatus to active(1). If |
| 3199 |
this set is successful, the agent has reserved |
| 3200 |
the resources specified by the ATM traffic |
| 3201 |
parameter and Service category values |
| 3202 |
for each direction of the VC cross-connect |
| 3203 |
in an ATM switch or network. |
| 3204 |
|
| 3205 |
(3) The manager sets the |
| 3206 |
atmVcCrossConnectAdminStatus to up(1) |
| 3207 |
in all rows of this VC cross-connect to |
| 3208 |
turn the traffic flow on. |
| 3209 |
|
| 3210 |
|
| 3211 |
One-Shot VC Cross-Connect Establishment |
| 3212 |
|
| 3213 |
A VC cross-connect may also be established in |
| 3214 |
one step by a set-request with all necessary |
| 3215 |
parameter values and atmVcCrossConnectRowStatus |
| 3216 |
set to createAndGo(4). |
| 3217 |
|
| 3218 |
In contrast to the negotiated VC cross-connect |
| 3219 |
establishment which allows for detailed error |
| 3220 |
checking i.e., set errors are explicitly linked to |
| 3221 |
particular resource acquisition failures), the |
| 3222 |
one-shot VC cross-connect establishment |
| 3223 |
performs the setup on one operation but does |
| 3224 |
not have the advantage of step-wise error |
| 3225 |
checking. |
| 3226 |
|
| 3227 |
VC Cross-Connect Retirement |
| 3228 |
|
| 3229 |
A VC cross-connect identified by a particular |
| 3230 |
value of atmVcCrossConnectIndex is released by: |
| 3231 |
|
| 3232 |
(1) Setting atmVcCrossConnectRowStatus of all rows |
| 3233 |
identified by this value of |
| 3234 |
atmVcCrossConnectIndex to destroy(6). |
| 3235 |
The agent may release all |
| 3236 |
associated resources, and the |
| 3237 |
atmVcCrossConnectIndex values in the |
| 3238 |
corresponding atmVclTable row are removed. |
| 3239 |
Note that a situation when only a subset of |
| 3240 |
the associated rows are deleted corresponds |
| 3241 |
|
| 3242 |
|
| 3243 |
|
| 3244 |
<span class="grey">Tesink Standards Track [Page 58]</span></pre> |
| 3245 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-59" ></span> |
| 3246 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3247 |
|
| 3248 |
|
| 3249 |
to a VC topology change. |
| 3250 |
|
| 3251 |
(2) After deletion of the appropriate |
| 3252 |
atmVcCrossConnectEntries, the manager may |
| 3253 |
set atmVclRowStatus to destroy(6) the |
| 3254 |
associated VCLs. The agent releases |
| 3255 |
the resources and removes the associated |
| 3256 |
rows in the atmVclTable. |
| 3257 |
|
| 3258 |
VC Cross-Connect Reconfiguration |
| 3259 |
|
| 3260 |
At the discretion of the agent, a VC |
| 3261 |
cross-connect may be reconfigured by |
| 3262 |
adding and/or deleting leafs to/from |
| 3263 |
the VC topology as per the VC cross-connect |
| 3264 |
establishment/retirement procedures. |
| 3265 |
Reconfiguration of traffic/service category parameter |
| 3266 |
values requires release of the VC cross-connect |
| 3267 |
before those parameter values may by changed |
| 3268 |
for individual VCLs." |
| 3269 |
INDEX { atmVcCrossConnectIndex, |
| 3270 |
atmVcCrossConnectLowIfIndex, |
| 3271 |
atmVcCrossConnectLowVpi, |
| 3272 |
atmVcCrossConnectLowVci, |
| 3273 |
atmVcCrossConnectHighIfIndex, |
| 3274 |
atmVcCrossConnectHighVpi, |
| 3275 |
atmVcCrossConnectHighVci } |
| 3276 |
::= { atmVcCrossConnectTable 1 } |
| 3277 |
|
| 3278 |
AtmVcCrossConnectEntry ::= SEQUENCE { |
| 3279 |
atmVcCrossConnectIndex INTEGER, |
| 3280 |
atmVcCrossConnectLowIfIndex InterfaceIndex, |
| 3281 |
atmVcCrossConnectLowVpi AtmVpIdentifier, |
| 3282 |
atmVcCrossConnectLowVci AtmVcIdentifier, |
| 3283 |
atmVcCrossConnectHighIfIndex InterfaceIndex, |
| 3284 |
atmVcCrossConnectHighVpi AtmVpIdentifier, |
| 3285 |
atmVcCrossConnectHighVci AtmVcIdentifier, |
| 3286 |
atmVcCrossConnectAdminStatus AtmVorXAdminStatus, |
| 3287 |
atmVcCrossConnectL2HOperStatus AtmVorXOperStatus, |
| 3288 |
atmVcCrossConnectH2LOperStatus AtmVorXOperStatus, |
| 3289 |
atmVcCrossConnectL2HLastChange AtmVorXLastChange, |
| 3290 |
atmVcCrossConnectH2LLastChange AtmVorXLastChange, |
| 3291 |
atmVcCrossConnectRowStatus RowStatus |
| 3292 |
} |
| 3293 |
|
| 3294 |
atmVcCrossConnectIndex OBJECT-TYPE |
| 3295 |
SYNTAX INTEGER (1..2147483647) |
| 3296 |
MAX-ACCESS not-accessible |
| 3297 |
|
| 3298 |
|
| 3299 |
|
| 3300 |
<span class="grey">Tesink Standards Track [Page 59]</span></pre> |
| 3301 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-60" ></span> |
| 3302 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3303 |
|
| 3304 |
|
| 3305 |
STATUS current |
| 3306 |
DESCRIPTION |
| 3307 |
"A unique value to identify this VC cross-connect. |
| 3308 |
For each VCL associated with this cross-connect, |
| 3309 |
the agent reports this cross-connect index value |
| 3310 |
in the atmVclCrossConnectIdentifier attribute of |
| 3311 |
the corresponding atmVclTable entries." |
| 3312 |
::= { atmVcCrossConnectEntry 1 } |
| 3313 |
|
| 3314 |
atmVcCrossConnectLowIfIndex OBJECT-TYPE |
| 3315 |
SYNTAX InterfaceIndex |
| 3316 |
MAX-ACCESS not-accessible |
| 3317 |
STATUS current |
| 3318 |
DESCRIPTION |
| 3319 |
"The ifIndex value of the ATM interface for this |
| 3320 |
VC cross-connect. The term low implies |
| 3321 |
that this ATM interface has the numerically lower |
| 3322 |
ifIndex value than the other ATM interface |
| 3323 |
identified in the same atmVcCrossConnectEntry." |
| 3324 |
::= { atmVcCrossConnectEntry 2 } |
| 3325 |
|
| 3326 |
atmVcCrossConnectLowVpi OBJECT-TYPE |
| 3327 |
SYNTAX AtmVpIdentifier |
| 3328 |
MAX-ACCESS not-accessible |
| 3329 |
STATUS current |
| 3330 |
DESCRIPTION |
| 3331 |
"The VPI value at the ATM interface |
| 3332 |
associated with the VC cross-connect that is |
| 3333 |
identified by atmVcCrossConnectLowIfIndex." |
| 3334 |
::= { atmVcCrossConnectEntry 3 } |
| 3335 |
|
| 3336 |
atmVcCrossConnectLowVci OBJECT-TYPE |
| 3337 |
SYNTAX AtmVcIdentifier |
| 3338 |
MAX-ACCESS not-accessible |
| 3339 |
STATUS current |
| 3340 |
DESCRIPTION |
| 3341 |
"The VCI value at the ATM interface |
| 3342 |
associated with this VC cross-connect that is |
| 3343 |
identified by atmVcCrossConnectLowIfIndex." |
| 3344 |
::= { atmVcCrossConnectEntry 4 } |
| 3345 |
|
| 3346 |
atmVcCrossConnectHighIfIndex OBJECT-TYPE |
| 3347 |
SYNTAX InterfaceIndex |
| 3348 |
MAX-ACCESS not-accessible |
| 3349 |
STATUS current |
| 3350 |
DESCRIPTION |
| 3351 |
"The ifIndex value for the ATM interface for |
| 3352 |
this VC cross-connect. The term high implies |
| 3353 |
|
| 3354 |
|
| 3355 |
|
| 3356 |
<span class="grey">Tesink Standards Track [Page 60]</span></pre> |
| 3357 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-61" ></span> |
| 3358 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3359 |
|
| 3360 |
|
| 3361 |
that this ATM interface has the numerically higher |
| 3362 |
ifIndex value than the other ATM interface |
| 3363 |
identified in the same atmVcCrossConnectEntry." |
| 3364 |
::= { atmVcCrossConnectEntry 5 } |
| 3365 |
|
| 3366 |
atmVcCrossConnectHighVpi OBJECT-TYPE |
| 3367 |
SYNTAX AtmVpIdentifier |
| 3368 |
MAX-ACCESS not-accessible |
| 3369 |
STATUS current |
| 3370 |
DESCRIPTION |
| 3371 |
"The VPI value at the ATM interface |
| 3372 |
associated with the VC cross-connect that is |
| 3373 |
identified by atmVcCrossConnectHighIfIndex." |
| 3374 |
::= { atmVcCrossConnectEntry 6 } |
| 3375 |
|
| 3376 |
atmVcCrossConnectHighVci OBJECT-TYPE |
| 3377 |
SYNTAX AtmVcIdentifier |
| 3378 |
MAX-ACCESS not-accessible |
| 3379 |
STATUS current |
| 3380 |
DESCRIPTION |
| 3381 |
"The VCI value at the ATM interface |
| 3382 |
associated with the VC cross-connect that is |
| 3383 |
identified by atmVcCrossConnectHighIfIndex." |
| 3384 |
::= { atmVcCrossConnectEntry 7 } |
| 3385 |
|
| 3386 |
atmVcCrossConnectAdminStatus OBJECT-TYPE |
| 3387 |
SYNTAX AtmVorXAdminStatus |
| 3388 |
MAX-ACCESS read-create |
| 3389 |
STATUS current |
| 3390 |
DESCRIPTION |
| 3391 |
"The desired administrative status of this |
| 3392 |
bi-directional VC cross-connect." |
| 3393 |
DEFVAL { down } |
| 3394 |
::= { atmVcCrossConnectEntry 8 } |
| 3395 |
|
| 3396 |
atmVcCrossConnectL2HOperStatus OBJECT-TYPE |
| 3397 |
SYNTAX AtmVorXOperStatus |
| 3398 |
MAX-ACCESS read-only |
| 3399 |
STATUS current |
| 3400 |
DESCRIPTION |
| 3401 |
"The current operational status of the |
| 3402 |
VC cross-connect in one direction; (i.e., |
| 3403 |
from the low to high direction)." |
| 3404 |
::= { atmVcCrossConnectEntry 9 } |
| 3405 |
|
| 3406 |
|
| 3407 |
atmVcCrossConnectH2LOperStatus OBJECT-TYPE |
| 3408 |
SYNTAX AtmVorXOperStatus |
| 3409 |
|
| 3410 |
|
| 3411 |
|
| 3412 |
<span class="grey">Tesink Standards Track [Page 61]</span></pre> |
| 3413 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-62" ></span> |
| 3414 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3415 |
|
| 3416 |
|
| 3417 |
MAX-ACCESS read-only |
| 3418 |
STATUS current |
| 3419 |
DESCRIPTION |
| 3420 |
"The current operational status of the |
| 3421 |
VC cross-connect in one direction; (i.e., |
| 3422 |
from the high to low direction)." |
| 3423 |
::= { atmVcCrossConnectEntry 10 } |
| 3424 |
|
| 3425 |
atmVcCrossConnectL2HLastChange OBJECT-TYPE |
| 3426 |
SYNTAX AtmVorXLastChange |
| 3427 |
MAX-ACCESS read-only |
| 3428 |
STATUS current |
| 3429 |
DESCRIPTION |
| 3430 |
"The value of sysUpTime at the time this |
| 3431 |
VC cross-connect entered its current |
| 3432 |
operational state in low to high direction." |
| 3433 |
::= { atmVcCrossConnectEntry 11 } |
| 3434 |
|
| 3435 |
atmVcCrossConnectH2LLastChange OBJECT-TYPE |
| 3436 |
SYNTAX AtmVorXLastChange |
| 3437 |
MAX-ACCESS read-only |
| 3438 |
STATUS current |
| 3439 |
DESCRIPTION |
| 3440 |
"The value of sysUpTime at the time this |
| 3441 |
VC cross-connect entered its current |
| 3442 |
operational state in high to low direction." |
| 3443 |
::= { atmVcCrossConnectEntry 12 } |
| 3444 |
|
| 3445 |
atmVcCrossConnectRowStatus OBJECT-TYPE |
| 3446 |
SYNTAX RowStatus |
| 3447 |
MAX-ACCESS read-create |
| 3448 |
STATUS current |
| 3449 |
DESCRIPTION |
| 3450 |
"The status of this entry in the |
| 3451 |
atmVcCrossConnectTable. This object is used to |
| 3452 |
create a new cross-connect for cross-connecting |
| 3453 |
VCLs which are created using the atmVclTable |
| 3454 |
or to change or delete existing cross-connect. |
| 3455 |
This object must be initially set to |
| 3456 |
`createAndWait' or 'createAndGo'. |
| 3457 |
To turn on a VC cross-connect, |
| 3458 |
the atmVcCrossConnectAdminStatus |
| 3459 |
is set to `up'." |
| 3460 |
DEFVAL { createAndWait } |
| 3461 |
::= { atmVcCrossConnectEntry 13 } |
| 3462 |
|
| 3463 |
|
| 3464 |
-- AAL5 Virtual Channel Connection Performance Statistics |
| 3465 |
|
| 3466 |
|
| 3467 |
|
| 3468 |
<span class="grey">Tesink Standards Track [Page 62]</span></pre> |
| 3469 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-63" ></span> |
| 3470 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3471 |
|
| 3472 |
|
| 3473 |
-- Table |
| 3474 |
|
| 3475 |
-- This table contains the AAL5 |
| 3476 |
-- performance statistics of a VCC at the |
| 3477 |
-- interface associated with an AAL5 entity in an ATM |
| 3478 |
-- host or ATM switch. |
| 3479 |
|
| 3480 |
|
| 3481 |
aal5VccTable OBJECT-TYPE |
| 3482 |
SYNTAX SEQUENCE OF Aal5VccEntry |
| 3483 |
MAX-ACCESS not-accessible |
| 3484 |
STATUS current |
| 3485 |
DESCRIPTION |
| 3486 |
"This table contains AAL5 VCC performance |
| 3487 |
parameters." |
| 3488 |
::= { atmMIBObjects 12 } |
| 3489 |
|
| 3490 |
aal5VccEntry OBJECT-TYPE |
| 3491 |
SYNTAX Aal5VccEntry |
| 3492 |
MAX-ACCESS not-accessible |
| 3493 |
STATUS current |
| 3494 |
DESCRIPTION |
| 3495 |
"This list contains the AAL5 VCC |
| 3496 |
performance parameters and is indexed |
| 3497 |
by ifIndex values of AAL5 interfaces |
| 3498 |
and the associated VPI/VCI values." |
| 3499 |
INDEX { ifIndex, aal5VccVpi, aal5VccVci } |
| 3500 |
::= { aal5VccTable 1 } |
| 3501 |
|
| 3502 |
Aal5VccEntry ::= SEQUENCE { |
| 3503 |
aal5VccVpi AtmVpIdentifier, |
| 3504 |
aal5VccVci AtmVcIdentifier, |
| 3505 |
aal5VccCrcErrors Counter32, |
| 3506 |
aal5VccSarTimeOuts Counter32, |
| 3507 |
aal5VccOverSizedSDUs Counter32 |
| 3508 |
} |
| 3509 |
|
| 3510 |
|
| 3511 |
aal5VccVpi OBJECT-TYPE |
| 3512 |
SYNTAX AtmVpIdentifier |
| 3513 |
MAX-ACCESS not-accessible |
| 3514 |
STATUS current |
| 3515 |
DESCRIPTION |
| 3516 |
"The VPI value of the AAL5 VCC at the |
| 3517 |
interface identified by the ifIndex." |
| 3518 |
::= { aal5VccEntry 1 } |
| 3519 |
|
| 3520 |
aal5VccVci OBJECT-TYPE |
| 3521 |
|
| 3522 |
|
| 3523 |
|
| 3524 |
<span class="grey">Tesink Standards Track [Page 63]</span></pre> |
| 3525 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-64" ></span> |
| 3526 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3527 |
|
| 3528 |
|
| 3529 |
SYNTAX AtmVcIdentifier |
| 3530 |
MAX-ACCESS not-accessible |
| 3531 |
STATUS current |
| 3532 |
DESCRIPTION |
| 3533 |
"The VCI value of the AAL5 VCC at the |
| 3534 |
interface identified by the ifIndex." |
| 3535 |
::= { aal5VccEntry 2 } |
| 3536 |
|
| 3537 |
aal5VccCrcErrors OBJECT-TYPE |
| 3538 |
SYNTAX Counter32 |
| 3539 |
MAX-ACCESS read-only |
| 3540 |
STATUS current |
| 3541 |
DESCRIPTION |
| 3542 |
"The number of AAL5 CPCS PDUs received with |
| 3543 |
CRC-32 errors on this AAL5 VCC at the |
| 3544 |
interface associated with an AAL5 entity." |
| 3545 |
::= { aal5VccEntry 3 } |
| 3546 |
|
| 3547 |
aal5VccSarTimeOuts OBJECT-TYPE |
| 3548 |
SYNTAX Counter32 |
| 3549 |
MAX-ACCESS read-only |
| 3550 |
STATUS current |
| 3551 |
DESCRIPTION |
| 3552 |
"The number of partially re-assembled AAL5 |
| 3553 |
CPCS PDUs which were discarded |
| 3554 |
on this AAL5 VCC at the interface associated |
| 3555 |
with an AAL5 entity because they |
| 3556 |
were not fully re-assembled within the |
| 3557 |
required time period. If the re-assembly |
| 3558 |
timer is not supported, then this object |
| 3559 |
contains a zero value." |
| 3560 |
::= { aal5VccEntry 4 } |
| 3561 |
|
| 3562 |
aal5VccOverSizedSDUs OBJECT-TYPE |
| 3563 |
SYNTAX Counter32 |
| 3564 |
MAX-ACCESS read-only |
| 3565 |
STATUS current |
| 3566 |
DESCRIPTION |
| 3567 |
"The number of AAL5 CPCS PDUs discarded |
| 3568 |
on this AAL5 VCC at the interface |
| 3569 |
associated with an AAL5 entity because the |
| 3570 |
AAL5 SDUs were too large." |
| 3571 |
::= { aal5VccEntry 5 } |
| 3572 |
|
| 3573 |
|
| 3574 |
-- |
| 3575 |
-- The following object may be used in conjunction with |
| 3576 |
-- the atmTrafficDescrParamTable for the creation of |
| 3577 |
|
| 3578 |
|
| 3579 |
|
| 3580 |
<span class="grey">Tesink Standards Track [Page 64]</span></pre> |
| 3581 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-65" ></span> |
| 3582 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3583 |
|
| 3584 |
|
| 3585 |
-- new table entries. |
| 3586 |
-- |
| 3587 |
|
| 3588 |
atmTrafficDescrParamIndexNext OBJECT-TYPE |
| 3589 |
SYNTAX INTEGER (0..2147483647) |
| 3590 |
MAX-ACCESS read-only |
| 3591 |
STATUS current |
| 3592 |
DESCRIPTION |
| 3593 |
"This object contains an appropriate value to |
| 3594 |
be used for atmTrafficDescrParamIndex when |
| 3595 |
creating entries in the |
| 3596 |
atmTrafficDescrParamTable. |
| 3597 |
The value 0 indicates that no unassigned |
| 3598 |
entries are available. To obtain the |
| 3599 |
atmTrafficDescrParamIndex value for a new |
| 3600 |
entry, the manager issues a management |
| 3601 |
protocol retrieval operation to obtain the |
| 3602 |
current value of this object. After each |
| 3603 |
retrieval, the agent should modify the value |
| 3604 |
to the next unassigned index. |
| 3605 |
After a manager retrieves a value the agent will |
| 3606 |
determine through its local policy when this index |
| 3607 |
value will be made available for reuse." |
| 3608 |
::= { atmMIBObjects 13 } |
| 3609 |
|
| 3610 |
|
| 3611 |
-- Conformance Information |
| 3612 |
|
| 3613 |
atmMIBConformance OBJECT IDENTIFIER ::= { atmMIB 2 } |
| 3614 |
|
| 3615 |
atmMIBGroups OBJECT IDENTIFIER |
| 3616 |
::= { atmMIBConformance 1 } |
| 3617 |
atmMIBCompliances OBJECT IDENTIFIER |
| 3618 |
::= { atmMIBConformance 2 } |
| 3619 |
|
| 3620 |
|
| 3621 |
-- Compliance Statements |
| 3622 |
|
| 3623 |
atmMIBCompliance2 MODULE-COMPLIANCE |
| 3624 |
STATUS current |
| 3625 |
DESCRIPTION |
| 3626 |
"The compliance statement for SNMP entities |
| 3627 |
including networks which have ATM and |
| 3628 |
AAL5 interfaces." |
| 3629 |
|
| 3630 |
MODULE -- this module |
| 3631 |
-- |
| 3632 |
-- ****** Interface and Traffic Descriptor Support *** |
| 3633 |
|
| 3634 |
|
| 3635 |
|
| 3636 |
<span class="grey">Tesink Standards Track [Page 65]</span></pre> |
| 3637 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-66" ></span> |
| 3638 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3639 |
|
| 3640 |
|
| 3641 |
-- |
| 3642 |
MANDATORY-GROUPS {atmInterfaceConfGroup2, |
| 3643 |
atmTrafficDescrGroup2 } |
| 3644 |
|
| 3645 |
OBJECT atmInterfaceMaxVpcs |
| 3646 |
MIN-ACCESS read-only |
| 3647 |
DESCRIPTION |
| 3648 |
"Write access is not required." |
| 3649 |
|
| 3650 |
OBJECT atmInterfaceMaxVccs |
| 3651 |
MIN-ACCESS read-only |
| 3652 |
DESCRIPTION |
| 3653 |
"Write access is not required." |
| 3654 |
|
| 3655 |
OBJECT atmInterfaceMaxActiveVpiBits |
| 3656 |
MIN-ACCESS read-only |
| 3657 |
DESCRIPTION |
| 3658 |
"Write access is not required. |
| 3659 |
At the ATM UNI the maximum number of |
| 3660 |
active VPI bits configured for use ranges |
| 3661 |
from 0 to 8 only. |
| 3662 |
Implementations may support smaller ranges." |
| 3663 |
OBJECT atmInterfaceMaxActiveVciBits |
| 3664 |
MIN-ACCESS read-only |
| 3665 |
DESCRIPTION |
| 3666 |
"Write access is not required. |
| 3667 |
Implementations may support smaller ranges." |
| 3668 |
|
| 3669 |
OBJECT atmInterfaceIlmiVpi |
| 3670 |
MIN-ACCESS read-only |
| 3671 |
DESCRIPTION |
| 3672 |
"Write access is not required." |
| 3673 |
|
| 3674 |
OBJECT atmInterfaceIlmiVci |
| 3675 |
MIN-ACCESS read-only |
| 3676 |
DESCRIPTION |
| 3677 |
"Write access is not required." |
| 3678 |
|
| 3679 |
OBJECT atmInterfaceMyNeighborIpAddress |
| 3680 |
MIN-ACCESS read-only |
| 3681 |
DESCRIPTION |
| 3682 |
"Write access is not required." |
| 3683 |
|
| 3684 |
OBJECT atmInterfaceMyNeighborIfName |
| 3685 |
MIN-ACCESS read-only |
| 3686 |
DESCRIPTION |
| 3687 |
"Write access is not required." |
| 3688 |
|
| 3689 |
|
| 3690 |
|
| 3691 |
|
| 3692 |
<span class="grey">Tesink Standards Track [Page 66]</span></pre> |
| 3693 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-67" ></span> |
| 3694 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3695 |
|
| 3696 |
|
| 3697 |
OBJECT atmInterfaceSubscrAddress |
| 3698 |
MIN-ACCESS read-only |
| 3699 |
DESCRIPTION |
| 3700 |
"Write access is not required." |
| 3701 |
|
| 3702 |
OBJECT atmTrafficDescrParamIndexNext |
| 3703 |
DESCRIPTION |
| 3704 |
"This object is only required for systems |
| 3705 |
that support the creation of entries in |
| 3706 |
the atmTrafficDescrParamTable." |
| 3707 |
|
| 3708 |
OBJECT atmTrafficDescrType |
| 3709 |
MIN-ACCESS read-only |
| 3710 |
DESCRIPTION |
| 3711 |
"Write access is not required." |
| 3712 |
|
| 3713 |
OBJECT atmTrafficDescrParam1 |
| 3714 |
MIN-ACCESS read-only |
| 3715 |
DESCRIPTION |
| 3716 |
"Write access is not required." |
| 3717 |
|
| 3718 |
OBJECT atmTrafficDescrParam2 |
| 3719 |
MIN-ACCESS read-only |
| 3720 |
DESCRIPTION |
| 3721 |
"Write access is not required." |
| 3722 |
|
| 3723 |
OBJECT atmTrafficDescrParam3 |
| 3724 |
MIN-ACCESS read-only |
| 3725 |
DESCRIPTION |
| 3726 |
"Write access is not required." |
| 3727 |
|
| 3728 |
OBJECT atmTrafficDescrParam4 |
| 3729 |
MIN-ACCESS read-only |
| 3730 |
DESCRIPTION |
| 3731 |
"Write access is not required." |
| 3732 |
|
| 3733 |
OBJECT atmTrafficDescrParam5 |
| 3734 |
MIN-ACCESS read-only |
| 3735 |
DESCRIPTION |
| 3736 |
"Write access is not required." |
| 3737 |
|
| 3738 |
OBJECT atmServiceCategory |
| 3739 |
MIN-ACCESS read-only |
| 3740 |
DESCRIPTION |
| 3741 |
"Write access is not required." |
| 3742 |
|
| 3743 |
OBJECT atmTrafficDescrRowStatus |
| 3744 |
SYNTAX INTEGER {active(1)} |
| 3745 |
|
| 3746 |
|
| 3747 |
|
| 3748 |
<span class="grey">Tesink Standards Track [Page 67]</span></pre> |
| 3749 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-68" ></span> |
| 3750 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3751 |
|
| 3752 |
|
| 3753 |
-- subset of RowStatus |
| 3754 |
MIN-ACCESS read-only |
| 3755 |
DESCRIPTION |
| 3756 |
"Write access is not required, and only one |
| 3757 |
of the six enumerated values for the |
| 3758 |
RowStatus textual convention need be |
| 3759 |
supported, specifically: active(1)." |
| 3760 |
|
| 3761 |
OBJECT atmTrafficFrameDiscard |
| 3762 |
MIN-ACCESS read-only |
| 3763 |
DESCRIPTION |
| 3764 |
"Write access is not required." |
| 3765 |
|
| 3766 |
-- |
| 3767 |
-- ****** DS3 PLCP Support ************************** |
| 3768 |
-- |
| 3769 |
GROUP atmInterfaceDs3PlcpGroup |
| 3770 |
DESCRIPTION |
| 3771 |
"This group is mandatory only for those |
| 3772 |
ATM interfaces which implement the |
| 3773 |
DS3 PLCP layer." |
| 3774 |
-- |
| 3775 |
-- ****** TC Sublayer Support ******************************** |
| 3776 |
-- |
| 3777 |
GROUP atmInterfaceTCGroup |
| 3778 |
DESCRIPTION |
| 3779 |
"This group is mandatory only for those |
| 3780 |
ATM interfaces which implement the |
| 3781 |
TC Sublayer." |
| 3782 |
|
| 3783 |
-- |
| 3784 |
-- ****** VPC Support ******************************* |
| 3785 |
-- |
| 3786 |
GROUP atmVpcTerminationGroup2 |
| 3787 |
DESCRIPTION |
| 3788 |
"This group is mandatory only for those |
| 3789 |
ATM interfaces which implement ATM |
| 3790 |
VPLs that terminate VPCs (i.e., ones which |
| 3791 |
are NOT cross-connected to other VPLs)." |
| 3792 |
|
| 3793 |
GROUP atmVplCrossConnectGroup |
| 3794 |
DESCRIPTION |
| 3795 |
"This group is mandatory only for those |
| 3796 |
ATM interfaces which implement ATM |
| 3797 |
VPLs that are not associated with VCLs |
| 3798 |
and are cross-connected to other VPLs |
| 3799 |
for VPCs." |
| 3800 |
|
| 3801 |
|
| 3802 |
|
| 3803 |
|
| 3804 |
<span class="grey">Tesink Standards Track [Page 68]</span></pre> |
| 3805 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-69" ></span> |
| 3806 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3807 |
|
| 3808 |
|
| 3809 |
GROUP atmVpPvcCrossConnectGroup |
| 3810 |
DESCRIPTION |
| 3811 |
"This group is mandatory only for those |
| 3812 |
ATM interfaces which implement ATM |
| 3813 |
VPLs that are not associated with VCLs |
| 3814 |
and are cross-connected to other VPLs |
| 3815 |
for permanent VPCs (i.e., PVCs). |
| 3816 |
This group is not used to crossconnect |
| 3817 |
a PVC with an SVC to form a Soft PVC." |
| 3818 |
|
| 3819 |
OBJECT atmVplAdminStatus |
| 3820 |
MIN-ACCESS read-only |
| 3821 |
DESCRIPTION |
| 3822 |
"Write access is not required." |
| 3823 |
|
| 3824 |
OBJECT atmVplReceiveTrafficDescrIndex |
| 3825 |
MIN-ACCESS read-only |
| 3826 |
DESCRIPTION |
| 3827 |
"Write access is not required." |
| 3828 |
|
| 3829 |
OBJECT atmVplTransmitTrafficDescrIndex |
| 3830 |
MIN-ACCESS read-only |
| 3831 |
DESCRIPTION |
| 3832 |
"Write access is not required." |
| 3833 |
|
| 3834 |
OBJECT atmVplRowStatus |
| 3835 |
SYNTAX INTEGER {active(1)} |
| 3836 |
-- subset of RowStatus |
| 3837 |
MIN-ACCESS read-only |
| 3838 |
DESCRIPTION |
| 3839 |
"Write access is not required, and only one |
| 3840 |
of the six enumerated values for the |
| 3841 |
RowStatus textual convention need be |
| 3842 |
supported, specifically: active(1)." |
| 3843 |
|
| 3844 |
OBJECT atmVplCastType |
| 3845 |
MIN-ACCESS read-only |
| 3846 |
DESCRIPTION |
| 3847 |
"Write access is not required." |
| 3848 |
|
| 3849 |
OBJECT atmVplConnKind |
| 3850 |
MIN-ACCESS read-only |
| 3851 |
DESCRIPTION |
| 3852 |
"Write access is not required." |
| 3853 |
|
| 3854 |
OBJECT atmVpCrossConnectAdminStatus |
| 3855 |
MIN-ACCESS read-only |
| 3856 |
DESCRIPTION |
| 3857 |
|
| 3858 |
|
| 3859 |
|
| 3860 |
<span class="grey">Tesink Standards Track [Page 69]</span></pre> |
| 3861 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-70" ></span> |
| 3862 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3863 |
|
| 3864 |
|
| 3865 |
"Write access is not required." |
| 3866 |
|
| 3867 |
OBJECT atmVpCrossConnectRowStatus |
| 3868 |
SYNTAX INTEGER {active(1)} |
| 3869 |
-- subset of RowStatus |
| 3870 |
MIN-ACCESS read-only |
| 3871 |
DESCRIPTION |
| 3872 |
"Write access is not required, and only one |
| 3873 |
of the six enumerated values for the |
| 3874 |
RowStatus textual convention need be |
| 3875 |
supported, specifically: active(1)." |
| 3876 |
|
| 3877 |
-- |
| 3878 |
-- ****** VCC Support ******************************* |
| 3879 |
-- |
| 3880 |
GROUP atmVccTerminationGroup2 |
| 3881 |
DESCRIPTION |
| 3882 |
"This group is mandatory only for those |
| 3883 |
ATM interfaces which implement ATM |
| 3884 |
VCLs that terminate VCCs (i.e., ones which |
| 3885 |
are NOT cross-connected to other VCLs)." |
| 3886 |
|
| 3887 |
GROUP atmVclCrossConnectGroup |
| 3888 |
DESCRIPTION |
| 3889 |
"This group is mandatory only for those |
| 3890 |
ATM interfaces which implement ATM |
| 3891 |
VCLs that are cross-connected to other VCLs |
| 3892 |
for VCCs." |
| 3893 |
|
| 3894 |
GROUP atmVcPvcCrossConnectGroup |
| 3895 |
DESCRIPTION |
| 3896 |
"This group is mandatory only for those |
| 3897 |
ATM interfaces which implement ATM |
| 3898 |
VCLs that are cross-connected to other |
| 3899 |
VCLs for permanent VCCs (i.e., PVCs). |
| 3900 |
This group is not used to crossconnect |
| 3901 |
a PVC with an SVC to form a Soft PVC." |
| 3902 |
|
| 3903 |
OBJECT atmVclAdminStatus |
| 3904 |
MIN-ACCESS read-only |
| 3905 |
DESCRIPTION |
| 3906 |
"Write access is not required." |
| 3907 |
|
| 3908 |
OBJECT atmVclReceiveTrafficDescrIndex |
| 3909 |
MIN-ACCESS read-only |
| 3910 |
DESCRIPTION |
| 3911 |
"Write access is not required." |
| 3912 |
|
| 3913 |
|
| 3914 |
|
| 3915 |
|
| 3916 |
<span class="grey">Tesink Standards Track [Page 70]</span></pre> |
| 3917 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-71" ></span> |
| 3918 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3919 |
|
| 3920 |
|
| 3921 |
OBJECT atmVclTransmitTrafficDescrIndex |
| 3922 |
MIN-ACCESS read-only |
| 3923 |
DESCRIPTION |
| 3924 |
"Write access is not required." |
| 3925 |
|
| 3926 |
OBJECT atmVccAalType |
| 3927 |
MIN-ACCESS read-only |
| 3928 |
DESCRIPTION |
| 3929 |
"Write access is not required." |
| 3930 |
|
| 3931 |
OBJECT atmVclRowStatus |
| 3932 |
SYNTAX INTEGER {active(1)} |
| 3933 |
-- subset of RowStatus |
| 3934 |
MIN-ACCESS read-only |
| 3935 |
DESCRIPTION |
| 3936 |
"Write access is not required, and only one |
| 3937 |
of the six enumerated values for the |
| 3938 |
RowStatus textual convention need be |
| 3939 |
supported, specifically: active(1)." |
| 3940 |
|
| 3941 |
OBJECT atmVclCastType |
| 3942 |
MIN-ACCESS read-only |
| 3943 |
DESCRIPTION |
| 3944 |
"Write access is not required." |
| 3945 |
|
| 3946 |
OBJECT atmVclConnKind |
| 3947 |
MIN-ACCESS read-only |
| 3948 |
DESCRIPTION |
| 3949 |
"Write access is not required." |
| 3950 |
|
| 3951 |
OBJECT atmVcCrossConnectAdminStatus |
| 3952 |
MIN-ACCESS read-only |
| 3953 |
DESCRIPTION |
| 3954 |
"Write access is not required." |
| 3955 |
|
| 3956 |
OBJECT atmVcCrossConnectRowStatus |
| 3957 |
SYNTAX INTEGER { active(1)} |
| 3958 |
-- subset of RowStatus |
| 3959 |
MIN-ACCESS read-only |
| 3960 |
DESCRIPTION |
| 3961 |
"Write access is not required, and only one |
| 3962 |
of the six enumerated values for the |
| 3963 |
RowStatus textual convention need be |
| 3964 |
supported, specifically: active(1)." |
| 3965 |
-- |
| 3966 |
-- ****** AAL5 Support ****************************** |
| 3967 |
-- |
| 3968 |
GROUP aal5VccGroup |
| 3969 |
|
| 3970 |
|
| 3971 |
|
| 3972 |
<span class="grey">Tesink Standards Track [Page 71]</span></pre> |
| 3973 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-72" ></span> |
| 3974 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 3975 |
|
| 3976 |
|
| 3977 |
DESCRIPTION |
| 3978 |
"This group is mandatory for the |
| 3979 |
AAL5 virtual connections only." |
| 3980 |
OBJECT atmVccAal5CpcsTransmitSduSize |
| 3981 |
MIN-ACCESS read-only |
| 3982 |
DESCRIPTION |
| 3983 |
"Write access is not required." |
| 3984 |
|
| 3985 |
OBJECT atmVccAal5CpcsReceiveSduSize |
| 3986 |
MIN-ACCESS read-only |
| 3987 |
DESCRIPTION |
| 3988 |
"Write access is not required." |
| 3989 |
|
| 3990 |
OBJECT atmVccAal5EncapsType |
| 3991 |
MIN-ACCESS read-only |
| 3992 |
DESCRIPTION |
| 3993 |
"Write access is not required." |
| 3994 |
::= { atmMIBCompliances 2 } |
| 3995 |
|
| 3996 |
|
| 3997 |
-- Units of Conformance |
| 3998 |
|
| 3999 |
atmInterfaceDs3PlcpGroup OBJECT-GROUP |
| 4000 |
OBJECTS {atmInterfaceDs3PlcpSEFSs, |
| 4001 |
atmInterfaceDs3PlcpAlarmState, |
| 4002 |
atmInterfaceDs3PlcpUASs} |
| 4003 |
STATUS current |
| 4004 |
DESCRIPTION |
| 4005 |
"A collection of objects providing information |
| 4006 |
about DS3 PLCP layer at an ATM interface." |
| 4007 |
::= { atmMIBGroups 3 } |
| 4008 |
|
| 4009 |
atmInterfaceTCGroup OBJECT-GROUP |
| 4010 |
OBJECTS { atmInterfaceOCDEvents, |
| 4011 |
atmInterfaceTCAlarmState } |
| 4012 |
STATUS current |
| 4013 |
DESCRIPTION |
| 4014 |
"A collection of objects providing information |
| 4015 |
about TC sublayer at an ATM interface." |
| 4016 |
::= { atmMIBGroups 4 } |
| 4017 |
|
| 4018 |
aal5VccGroup OBJECT-GROUP |
| 4019 |
OBJECTS {atmVccAal5CpcsTransmitSduSize, |
| 4020 |
atmVccAal5CpcsReceiveSduSize, |
| 4021 |
atmVccAal5EncapsType, |
| 4022 |
aal5VccCrcErrors, aal5VccSarTimeOuts, |
| 4023 |
aal5VccOverSizedSDUs } |
| 4024 |
STATUS current |
| 4025 |
|
| 4026 |
|
| 4027 |
|
| 4028 |
<span class="grey">Tesink Standards Track [Page 72]</span></pre> |
| 4029 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-73" ></span> |
| 4030 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 4031 |
|
| 4032 |
|
| 4033 |
DESCRIPTION |
| 4034 |
"A collection of objects providing |
| 4035 |
AAL5 configuration and performance statistics |
| 4036 |
of a VCC." |
| 4037 |
::= { atmMIBGroups 9 } |
| 4038 |
|
| 4039 |
atmInterfaceConfGroup2 OBJECT-GROUP |
| 4040 |
OBJECTS { |
| 4041 |
atmInterfaceMaxVpcs, atmInterfaceMaxVccs, |
| 4042 |
atmInterfaceConfVpcs, atmInterfaceConfVccs, |
| 4043 |
atmInterfaceMaxActiveVpiBits, |
| 4044 |
atmInterfaceMaxActiveVciBits, |
| 4045 |
atmInterfaceIlmiVpi, |
| 4046 |
atmInterfaceIlmiVci, |
| 4047 |
atmInterfaceMyNeighborIpAddress, |
| 4048 |
atmInterfaceMyNeighborIfName, |
| 4049 |
atmInterfaceCurrentMaxVpiBits, |
| 4050 |
atmInterfaceCurrentMaxVciBits, |
| 4051 |
atmInterfaceSubscrAddress } |
| 4052 |
STATUS current |
| 4053 |
DESCRIPTION |
| 4054 |
"A collection of objects providing configuration |
| 4055 |
information about an ATM interface." |
| 4056 |
::= { atmMIBGroups 10 } |
| 4057 |
|
| 4058 |
atmTrafficDescrGroup2 OBJECT-GROUP |
| 4059 |
OBJECTS { |
| 4060 |
atmTrafficDescrType, atmTrafficDescrParam1, |
| 4061 |
atmTrafficDescrParam2, atmTrafficDescrParam3, |
| 4062 |
atmTrafficDescrParam4, atmTrafficDescrParam5, |
| 4063 |
atmTrafficDescrRowStatus, atmServiceCategory, |
| 4064 |
atmTrafficFrameDiscard, |
| 4065 |
atmTrafficDescrParamIndexNext } |
| 4066 |
STATUS current |
| 4067 |
DESCRIPTION |
| 4068 |
"A collection of objects providing information |
| 4069 |
about ATM traffic descriptor type and |
| 4070 |
the associated parameters." |
| 4071 |
::= { atmMIBGroups 11 } |
| 4072 |
|
| 4073 |
atmVpcTerminationGroup2 OBJECT-GROUP |
| 4074 |
OBJECTS {atmVplOperStatus, atmVplAdminStatus, |
| 4075 |
atmVplLastChange, |
| 4076 |
atmVplReceiveTrafficDescrIndex, |
| 4077 |
atmVplTransmitTrafficDescrIndex, |
| 4078 |
atmVplRowStatus, atmVplCastType, |
| 4079 |
atmVplConnKind } |
| 4080 |
STATUS current |
| 4081 |
|
| 4082 |
|
| 4083 |
|
| 4084 |
<span class="grey">Tesink Standards Track [Page 73]</span></pre> |
| 4085 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-74" ></span> |
| 4086 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 4087 |
|
| 4088 |
|
| 4089 |
DESCRIPTION |
| 4090 |
"A collection of objects providing information |
| 4091 |
about a VPL at an ATM interface which |
| 4092 |
terminates a VPC (i.e., one which is NOT |
| 4093 |
cross-connected to other VPLs)." |
| 4094 |
::= { atmMIBGroups 12 } |
| 4095 |
|
| 4096 |
atmVccTerminationGroup2 OBJECT-GROUP |
| 4097 |
OBJECTS {atmVclOperStatus, atmVclAdminStatus, |
| 4098 |
atmVclLastChange, |
| 4099 |
atmVclReceiveTrafficDescrIndex, |
| 4100 |
atmVclTransmitTrafficDescrIndex, |
| 4101 |
atmVccAalType, atmVclRowStatus, |
| 4102 |
atmVclCastType, atmVclConnKind } |
| 4103 |
STATUS current |
| 4104 |
DESCRIPTION |
| 4105 |
"A collection of objects providing information |
| 4106 |
about a VCL at an ATM interface |
| 4107 |
which terminates a VCC (i.e., one which is |
| 4108 |
NOT cross-connected to other VCLs)." |
| 4109 |
::= { atmMIBGroups 13 } |
| 4110 |
|
| 4111 |
atmVplCrossConnectGroup OBJECT-GROUP |
| 4112 |
OBJECTS { atmVplReceiveTrafficDescrIndex, |
| 4113 |
atmVplTransmitTrafficDescrIndex, |
| 4114 |
atmVplOperStatus, atmVplLastChange, |
| 4115 |
atmVplRowStatus, |
| 4116 |
atmVplCastType, atmVplConnKind } |
| 4117 |
STATUS current |
| 4118 |
DESCRIPTION |
| 4119 |
"A collection of objects providing |
| 4120 |
information about the VPLs that |
| 4121 |
are cross-connected together." |
| 4122 |
::= { atmMIBGroups 14 } |
| 4123 |
|
| 4124 |
atmVpPvcCrossConnectGroup OBJECT-GROUP |
| 4125 |
OBJECTS { atmVpCrossConnectAdminStatus, |
| 4126 |
atmVpCrossConnectL2HOperStatus, |
| 4127 |
atmVpCrossConnectH2LOperStatus, |
| 4128 |
atmVpCrossConnectL2HLastChange, |
| 4129 |
atmVpCrossConnectH2LLastChange, |
| 4130 |
atmVpCrossConnectRowStatus, |
| 4131 |
atmVplCrossConnectIdentifier, |
| 4132 |
atmVpCrossConnectIndexNext } |
| 4133 |
STATUS current |
| 4134 |
DESCRIPTION |
| 4135 |
"A collection of objects providing |
| 4136 |
information about a VP cross-connect |
| 4137 |
|
| 4138 |
|
| 4139 |
|
| 4140 |
<span class="grey">Tesink Standards Track [Page 74]</span></pre> |
| 4141 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-75" ></span> |
| 4142 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 4143 |
|
| 4144 |
|
| 4145 |
for PVCs. These objects are not used |
| 4146 |
for Soft PVCs or SVCs." |
| 4147 |
::= { atmMIBGroups 15 } |
| 4148 |
|
| 4149 |
atmVclCrossConnectGroup OBJECT-GROUP |
| 4150 |
OBJECTS { atmVclReceiveTrafficDescrIndex, |
| 4151 |
atmVclTransmitTrafficDescrIndex, |
| 4152 |
atmVclOperStatus, atmVclLastChange, |
| 4153 |
atmVclRowStatus, |
| 4154 |
atmVclCastType, atmVclConnKind } |
| 4155 |
STATUS current |
| 4156 |
DESCRIPTION |
| 4157 |
"A collection of objects providing |
| 4158 |
information about the VCLs that |
| 4159 |
are cross-connected together." |
| 4160 |
::= { atmMIBGroups 16 } |
| 4161 |
|
| 4162 |
atmVcPvcCrossConnectGroup OBJECT-GROUP |
| 4163 |
OBJECTS { atmVcCrossConnectAdminStatus, |
| 4164 |
atmVcCrossConnectL2HOperStatus, |
| 4165 |
atmVcCrossConnectH2LOperStatus, |
| 4166 |
atmVcCrossConnectL2HLastChange, |
| 4167 |
atmVcCrossConnectH2LLastChange, |
| 4168 |
atmVcCrossConnectRowStatus, |
| 4169 |
atmVclCrossConnectIdentifier, |
| 4170 |
atmVcCrossConnectIndexNext } |
| 4171 |
STATUS current |
| 4172 |
DESCRIPTION |
| 4173 |
"A collection of objects providing |
| 4174 |
information about a VC cross-connect |
| 4175 |
for PVCs. These objects are not used |
| 4176 |
for Soft PVCs or SVCs." |
| 4177 |
::= { atmMIBGroups 17 } |
| 4178 |
|
| 4179 |
|
| 4180 |
-- Deprecated Definitions - Objects |
| 4181 |
|
| 4182 |
-- atmInterfaceAddressType |
| 4183 |
-- atmTrafficQoSClass |
| 4184 |
|
| 4185 |
|
| 4186 |
-- Deprecated Definitions - Compliance |
| 4187 |
|
| 4188 |
atmMIBCompliance MODULE-COMPLIANCE |
| 4189 |
STATUS deprecated |
| 4190 |
DESCRIPTION |
| 4191 |
"The compliance statement for SNMP entities |
| 4192 |
including networks which have ATM and |
| 4193 |
|
| 4194 |
|
| 4195 |
|
| 4196 |
<span class="grey">Tesink Standards Track [Page 75]</span></pre> |
| 4197 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-76" ></span> |
| 4198 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 4199 |
|
| 4200 |
|
| 4201 |
AAL5 interfaces." |
| 4202 |
|
| 4203 |
MODULE -- this module |
| 4204 |
MANDATORY-GROUPS {atmInterfaceConfGroup, |
| 4205 |
atmTrafficDescrGroup} |
| 4206 |
|
| 4207 |
OBJECT atmInterfaceMaxVpcs |
| 4208 |
MIN-ACCESS read-only |
| 4209 |
DESCRIPTION |
| 4210 |
"Write access is not required." |
| 4211 |
|
| 4212 |
OBJECT atmInterfaceMaxVccs |
| 4213 |
MIN-ACCESS read-only |
| 4214 |
DESCRIPTION |
| 4215 |
"Write access is not required." |
| 4216 |
|
| 4217 |
OBJECT atmInterfaceMaxActiveVpiBits |
| 4218 |
MIN-ACCESS read-only |
| 4219 |
DESCRIPTION |
| 4220 |
"Write access is not required." |
| 4221 |
|
| 4222 |
OBJECT atmInterfaceMaxActiveVciBits |
| 4223 |
MIN-ACCESS read-only |
| 4224 |
DESCRIPTION |
| 4225 |
"Write access is not required." |
| 4226 |
|
| 4227 |
OBJECT atmInterfaceIlmiVpi |
| 4228 |
MIN-ACCESS read-only |
| 4229 |
DESCRIPTION |
| 4230 |
"Write access is not required." |
| 4231 |
|
| 4232 |
OBJECT atmInterfaceIlmiVci |
| 4233 |
MIN-ACCESS read-only |
| 4234 |
DESCRIPTION |
| 4235 |
"Write access is not required." |
| 4236 |
|
| 4237 |
OBJECT atmInterfaceMyNeighborIpAddress |
| 4238 |
MIN-ACCESS read-only |
| 4239 |
DESCRIPTION |
| 4240 |
"Write access is not required." |
| 4241 |
|
| 4242 |
OBJECT atmInterfaceMyNeighborIfName |
| 4243 |
MIN-ACCESS read-only |
| 4244 |
DESCRIPTION |
| 4245 |
"Write access is not required." |
| 4246 |
|
| 4247 |
OBJECT atmTrafficDescrType |
| 4248 |
MIN-ACCESS read-only |
| 4249 |
|
| 4250 |
|
| 4251 |
|
| 4252 |
<span class="grey">Tesink Standards Track [Page 76]</span></pre> |
| 4253 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-77" ></span> |
| 4254 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 4255 |
|
| 4256 |
|
| 4257 |
DESCRIPTION |
| 4258 |
"Write access is not required." |
| 4259 |
|
| 4260 |
OBJECT atmTrafficDescrParam1 |
| 4261 |
MIN-ACCESS read-only |
| 4262 |
DESCRIPTION |
| 4263 |
"Write access is not required." |
| 4264 |
|
| 4265 |
OBJECT atmTrafficDescrParam2 |
| 4266 |
MIN-ACCESS read-only |
| 4267 |
DESCRIPTION |
| 4268 |
"Write access is not required." |
| 4269 |
|
| 4270 |
OBJECT atmTrafficDescrParam3 |
| 4271 |
MIN-ACCESS read-only |
| 4272 |
DESCRIPTION |
| 4273 |
"Write access is not required." |
| 4274 |
|
| 4275 |
OBJECT atmTrafficDescrParam4 |
| 4276 |
MIN-ACCESS read-only |
| 4277 |
DESCRIPTION |
| 4278 |
"Write access is not required." |
| 4279 |
|
| 4280 |
OBJECT atmTrafficDescrParam5 |
| 4281 |
MIN-ACCESS read-only |
| 4282 |
DESCRIPTION |
| 4283 |
"Write access is not required." |
| 4284 |
|
| 4285 |
OBJECT atmTrafficQoSClass |
| 4286 |
MIN-ACCESS read-only |
| 4287 |
DESCRIPTION |
| 4288 |
"Write access is not required." |
| 4289 |
|
| 4290 |
OBJECT atmTrafficDescrRowStatus |
| 4291 |
SYNTAX INTEGER {active(1)} |
| 4292 |
-- subset of RowStatus |
| 4293 |
MIN-ACCESS read-only |
| 4294 |
DESCRIPTION |
| 4295 |
"Write access is not required, and only one |
| 4296 |
of the six enumerated values for the |
| 4297 |
RowStatus textual convention need be |
| 4298 |
supported, specifically: active(1)." |
| 4299 |
|
| 4300 |
GROUP atmInterfaceDs3PlcpGroup |
| 4301 |
DESCRIPTION |
| 4302 |
"This group is mandatory only for those |
| 4303 |
ATM interfaces which implement the |
| 4304 |
DS3 PLCP layer." |
| 4305 |
|
| 4306 |
|
| 4307 |
|
| 4308 |
<span class="grey">Tesink Standards Track [Page 77]</span></pre> |
| 4309 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-78" ></span> |
| 4310 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 4311 |
|
| 4312 |
|
| 4313 |
GROUP atmInterfaceTCGroup |
| 4314 |
DESCRIPTION |
| 4315 |
"This group is mandatory only for those |
| 4316 |
ATM interfaces which implement the |
| 4317 |
TC Sublayer." |
| 4318 |
|
| 4319 |
GROUP atmVpcTerminationGroup |
| 4320 |
DESCRIPTION |
| 4321 |
"This group is mandatory only for those |
| 4322 |
ATM interfaces which implement ATM |
| 4323 |
VPLs that terminate VPCs (i.e., ones which |
| 4324 |
are NOT cross-connected to other VPLs)." |
| 4325 |
|
| 4326 |
GROUP atmVpCrossConnectGroup |
| 4327 |
DESCRIPTION |
| 4328 |
"This group is mandatory only for those |
| 4329 |
ATM interfaces which implement ATM |
| 4330 |
VPLs that are not associated with VCLs |
| 4331 |
and are cross-connected to other VPLs." |
| 4332 |
|
| 4333 |
OBJECT atmVplAdminStatus |
| 4334 |
MIN-ACCESS read-only |
| 4335 |
DESCRIPTION |
| 4336 |
"Write access is not required." |
| 4337 |
|
| 4338 |
OBJECT atmVplReceiveTrafficDescrIndex |
| 4339 |
MIN-ACCESS read-only |
| 4340 |
DESCRIPTION |
| 4341 |
"Write access is not required." |
| 4342 |
|
| 4343 |
OBJECT atmVplTransmitTrafficDescrIndex |
| 4344 |
MIN-ACCESS read-only |
| 4345 |
DESCRIPTION |
| 4346 |
"Write access is not required." |
| 4347 |
|
| 4348 |
OBJECT atmVplRowStatus |
| 4349 |
SYNTAX INTEGER {active(1)} |
| 4350 |
-- subset of RowStatus |
| 4351 |
MIN-ACCESS read-only |
| 4352 |
DESCRIPTION |
| 4353 |
"Write access is not required, and only one |
| 4354 |
of the six enumerated values for the |
| 4355 |
RowStatus textual convention need be |
| 4356 |
supported, specifically: active(1)." |
| 4357 |
|
| 4358 |
OBJECT atmVpCrossConnectAdminStatus |
| 4359 |
MIN-ACCESS read-only |
| 4360 |
DESCRIPTION |
| 4361 |
|
| 4362 |
|
| 4363 |
|
| 4364 |
<span class="grey">Tesink Standards Track [Page 78]</span></pre> |
| 4365 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-79" ></span> |
| 4366 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 4367 |
|
| 4368 |
|
| 4369 |
"Write access is not required." |
| 4370 |
|
| 4371 |
OBJECT atmVpCrossConnectRowStatus |
| 4372 |
SYNTAX INTEGER {active(1)} |
| 4373 |
-- subset of RowStatus |
| 4374 |
MIN-ACCESS read-only |
| 4375 |
DESCRIPTION |
| 4376 |
"Write access is not required, and only one |
| 4377 |
of the six enumerated values for the |
| 4378 |
RowStatus textual convention need be |
| 4379 |
supported, specifically: active(1)." |
| 4380 |
|
| 4381 |
GROUP atmVccTerminationGroup |
| 4382 |
DESCRIPTION |
| 4383 |
"This group is mandatory only for those |
| 4384 |
ATM interfaces which implement ATM |
| 4385 |
VCLs that terminate VCCs (i.e., ones which |
| 4386 |
are NOT cross-connected to other VCLs)." |
| 4387 |
|
| 4388 |
GROUP atmVcCrossConnectGroup |
| 4389 |
DESCRIPTION |
| 4390 |
"This group is mandatory only for those |
| 4391 |
ATM interfaces which implement ATM |
| 4392 |
VCLs that are cross-connected to |
| 4393 |
other VCLs." |
| 4394 |
|
| 4395 |
OBJECT atmVclAdminStatus |
| 4396 |
MIN-ACCESS read-only |
| 4397 |
DESCRIPTION |
| 4398 |
"Write access is not required." |
| 4399 |
|
| 4400 |
OBJECT atmVclReceiveTrafficDescrIndex |
| 4401 |
MIN-ACCESS read-only |
| 4402 |
DESCRIPTION |
| 4403 |
"Write access is not required." |
| 4404 |
|
| 4405 |
OBJECT atmVclTransmitTrafficDescrIndex |
| 4406 |
MIN-ACCESS read-only |
| 4407 |
DESCRIPTION |
| 4408 |
"Write access is not required." |
| 4409 |
|
| 4410 |
OBJECT atmVccAalType |
| 4411 |
MIN-ACCESS read-only |
| 4412 |
DESCRIPTION |
| 4413 |
"Write access is not required." |
| 4414 |
|
| 4415 |
OBJECT atmVclRowStatus |
| 4416 |
SYNTAX INTEGER {active(1)} |
| 4417 |
|
| 4418 |
|
| 4419 |
|
| 4420 |
<span class="grey">Tesink Standards Track [Page 79]</span></pre> |
| 4421 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-80" ></span> |
| 4422 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 4423 |
|
| 4424 |
|
| 4425 |
-- subset of RowStatus |
| 4426 |
MIN-ACCESS read-only |
| 4427 |
DESCRIPTION |
| 4428 |
"Write access is not required, and only one |
| 4429 |
of the six enumerated values for the |
| 4430 |
RowStatus textual convention need be |
| 4431 |
supported, specifically: active(1)." |
| 4432 |
|
| 4433 |
OBJECT atmVcCrossConnectAdminStatus |
| 4434 |
MIN-ACCESS read-only |
| 4435 |
DESCRIPTION |
| 4436 |
"Write access is not required." |
| 4437 |
|
| 4438 |
OBJECT atmVcCrossConnectRowStatus |
| 4439 |
SYNTAX INTEGER { active(1)} |
| 4440 |
-- subset of RowStatus |
| 4441 |
MIN-ACCESS read-only |
| 4442 |
DESCRIPTION |
| 4443 |
"Write access is not required, and only one |
| 4444 |
of the six enumerated values for the |
| 4445 |
RowStatus textual convention need be |
| 4446 |
supported, specifically: active(1)." |
| 4447 |
|
| 4448 |
GROUP aal5VccGroup |
| 4449 |
DESCRIPTION |
| 4450 |
"This group is mandatory for the |
| 4451 |
AAL5 virtual connections only." |
| 4452 |
|
| 4453 |
OBJECT atmVccAal5CpcsTransmitSduSize |
| 4454 |
MIN-ACCESS read-only |
| 4455 |
DESCRIPTION |
| 4456 |
"Write access is not required." |
| 4457 |
|
| 4458 |
OBJECT atmVccAal5CpcsReceiveSduSize |
| 4459 |
MIN-ACCESS read-only |
| 4460 |
DESCRIPTION |
| 4461 |
"Write access is not required." |
| 4462 |
|
| 4463 |
OBJECT atmVccAal5EncapsType |
| 4464 |
MIN-ACCESS read-only |
| 4465 |
DESCRIPTION |
| 4466 |
"Write access is not required." |
| 4467 |
::= { atmMIBCompliances 1 } |
| 4468 |
|
| 4469 |
|
| 4470 |
-- Deprecated Definitions - Groups |
| 4471 |
|
| 4472 |
|
| 4473 |
|
| 4474 |
|
| 4475 |
|
| 4476 |
<span class="grey">Tesink Standards Track [Page 80]</span></pre> |
| 4477 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-81" ></span> |
| 4478 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 4479 |
|
| 4480 |
|
| 4481 |
atmInterfaceConfGroup OBJECT-GROUP |
| 4482 |
OBJECTS { |
| 4483 |
atmInterfaceMaxVpcs, atmInterfaceMaxVccs, |
| 4484 |
atmInterfaceConfVpcs, atmInterfaceConfVccs, |
| 4485 |
atmInterfaceMaxActiveVpiBits, |
| 4486 |
atmInterfaceMaxActiveVciBits, |
| 4487 |
atmInterfaceIlmiVpi, |
| 4488 |
atmInterfaceIlmiVci, |
| 4489 |
atmInterfaceAddressType, |
| 4490 |
atmInterfaceAdminAddress, |
| 4491 |
atmInterfaceMyNeighborIpAddress, |
| 4492 |
atmInterfaceMyNeighborIfName } |
| 4493 |
STATUS deprecated |
| 4494 |
DESCRIPTION |
| 4495 |
"A collection of objects providing configuration |
| 4496 |
information about an ATM interface." |
| 4497 |
::= { atmMIBGroups 1 } |
| 4498 |
|
| 4499 |
atmTrafficDescrGroup OBJECT-GROUP |
| 4500 |
OBJECTS { |
| 4501 |
atmTrafficDescrType, atmTrafficDescrParam1, |
| 4502 |
atmTrafficDescrParam2, atmTrafficDescrParam3, |
| 4503 |
atmTrafficDescrParam4, atmTrafficDescrParam5, |
| 4504 |
atmTrafficQoSClass, atmTrafficDescrRowStatus} |
| 4505 |
STATUS deprecated |
| 4506 |
DESCRIPTION |
| 4507 |
"A collection of objects providing information |
| 4508 |
about ATM traffic descriptor type and |
| 4509 |
the associated parameters." |
| 4510 |
::= { atmMIBGroups 2 } |
| 4511 |
|
| 4512 |
atmVpcTerminationGroup OBJECT-GROUP |
| 4513 |
OBJECTS {atmVplOperStatus, atmVplAdminStatus, |
| 4514 |
atmVplLastChange, |
| 4515 |
atmVplReceiveTrafficDescrIndex, |
| 4516 |
atmVplTransmitTrafficDescrIndex, |
| 4517 |
atmVplRowStatus } |
| 4518 |
STATUS deprecated |
| 4519 |
DESCRIPTION |
| 4520 |
"A collection of objects providing |
| 4521 |
information about a VPL at an ATM interface |
| 4522 |
which terminates a VPC |
| 4523 |
(i.e., one which is NOT cross-connected |
| 4524 |
to other VPLs)." |
| 4525 |
::= { atmMIBGroups 5 } |
| 4526 |
|
| 4527 |
atmVccTerminationGroup OBJECT-GROUP |
| 4528 |
OBJECTS {atmVclOperStatus, atmVclAdminStatus, |
| 4529 |
|
| 4530 |
|
| 4531 |
|
| 4532 |
<span class="grey">Tesink Standards Track [Page 81]</span></pre> |
| 4533 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-82" ></span> |
| 4534 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 4535 |
|
| 4536 |
|
| 4537 |
atmVclLastChange, |
| 4538 |
atmVclReceiveTrafficDescrIndex, |
| 4539 |
atmVclTransmitTrafficDescrIndex, |
| 4540 |
atmVccAalType, atmVclRowStatus } |
| 4541 |
STATUS deprecated |
| 4542 |
DESCRIPTION |
| 4543 |
"A collection of objects providing information |
| 4544 |
about a VCL at an ATM interface |
| 4545 |
which terminates a VCC (i.e., one which is |
| 4546 |
NOT cross-connected to other VCLs)." |
| 4547 |
::= { atmMIBGroups 6 } |
| 4548 |
|
| 4549 |
atmVpCrossConnectGroup OBJECT-GROUP |
| 4550 |
OBJECTS { atmVplReceiveTrafficDescrIndex, |
| 4551 |
atmVplTransmitTrafficDescrIndex, |
| 4552 |
atmVplOperStatus, atmVplRowStatus, |
| 4553 |
atmVpCrossConnectAdminStatus, |
| 4554 |
atmVpCrossConnectL2HOperStatus, |
| 4555 |
atmVpCrossConnectH2LOperStatus, |
| 4556 |
atmVpCrossConnectL2HLastChange, |
| 4557 |
atmVpCrossConnectH2LLastChange, |
| 4558 |
atmVpCrossConnectRowStatus, |
| 4559 |
atmVplCrossConnectIdentifier, |
| 4560 |
atmVpCrossConnectIndexNext } |
| 4561 |
STATUS deprecated |
| 4562 |
DESCRIPTION |
| 4563 |
"A collection of objects providing |
| 4564 |
information about a VP cross-connect |
| 4565 |
and the associated VPLs that are |
| 4566 |
cross-connected together." |
| 4567 |
::= { atmMIBGroups 7 } |
| 4568 |
|
| 4569 |
atmVcCrossConnectGroup OBJECT-GROUP |
| 4570 |
OBJECTS { atmVclReceiveTrafficDescrIndex, |
| 4571 |
atmVclTransmitTrafficDescrIndex, |
| 4572 |
atmVclOperStatus, atmVclRowStatus, |
| 4573 |
atmVcCrossConnectAdminStatus, |
| 4574 |
atmVcCrossConnectL2HOperStatus, |
| 4575 |
atmVcCrossConnectH2LOperStatus, |
| 4576 |
atmVcCrossConnectL2HLastChange, |
| 4577 |
atmVcCrossConnectH2LLastChange, |
| 4578 |
atmVcCrossConnectRowStatus, |
| 4579 |
atmVclCrossConnectIdentifier, |
| 4580 |
atmVcCrossConnectIndexNext } |
| 4581 |
STATUS deprecated |
| 4582 |
DESCRIPTION |
| 4583 |
"A collection of objects providing |
| 4584 |
information about a VC cross-connect |
| 4585 |
|
| 4586 |
|
| 4587 |
|
| 4588 |
<span class="grey">Tesink Standards Track [Page 82]</span></pre> |
| 4589 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-83" ></span> |
| 4590 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 4591 |
|
| 4592 |
|
| 4593 |
and the associated VCLs that are |
| 4594 |
cross-connected together." |
| 4595 |
::= { atmMIBGroups 8 } |
| 4596 |
|
| 4597 |
|
| 4598 |
-- {atmMIB 3} has been used by [<a href="#ref-19" title=""Definitions of Textual Conventions and OBJECT-IDENTITIES for ATM Management"">19</a>]. |
| 4599 |
|
| 4600 |
END |
| 4601 |
|
| 4602 |
<span class="h2"><a class="selflink" id="section-10" href="#section-10">10</a>. Acknowledgments</span> |
| 4603 |
|
| 4604 |
This memo is the result of the work of the AToMMIB Working Group. |
| 4605 |
|
| 4606 |
<span class="h2"><a class="selflink" id="section-11" href="#section-11">11</a>. References</span> |
| 4607 |
|
| 4608 |
[<a id="ref-1">1</a>] Harrington, D., Presuhn, R. and B. Wijnen, "An |
| 4609 |
Architecture for Describing SNMP Management Frameworks", <a href="./rfc2271">RFC</a> |
| 4610 |
<a href="./rfc2271">2271</a>, January 1998. |
| 4611 |
|
| 4612 |
[<a id="ref-2">2</a>] Rose, M. and K. McCloghrie, "Structure and Identification of |
| 4613 |
Management Information for TCP/IP-based Internets", STD 16, <a href="./rfc1155">RFC</a> |
| 4614 |
<a href="./rfc1155">1155</a>, May 1990. |
| 4615 |
|
| 4616 |
[<a id="ref-3">3</a>] Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD 16, |
| 4617 |
<a href="./rfc1212">RFC 1212</a>, March 1991. |
| 4618 |
|
| 4619 |
[<a id="ref-4">4</a>] Rose, M., "A Convention for Defining Traps for use with the |
| 4620 |
SNMP", <a href="./rfc1215">RFC 1215</a>, March 1991. |
| 4621 |
|
| 4622 |
[<a id="ref-5">5</a>] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M. and S. |
| 4623 |
Waldbusser, "Structure of Management Information for Version 2 |
| 4624 |
of the Simple Network Management Protocol (SNMPv2)", <a href="./rfc1902">RFC 1902</a>, |
| 4625 |
January 1996. |
| 4626 |
|
| 4627 |
[<a id="ref-6">6</a>] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M. and S. |
| 4628 |
Waldbusser, "Textual Conventions for Version 2 of the Simple |
| 4629 |
Network Management Protocol (SNMPv2)", <a href="./rfc1903">RFC 1903</a>, January 1996. |
| 4630 |
|
| 4631 |
[<a id="ref-7">7</a>] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M. and S. |
| 4632 |
Waldbusser, "Conformance Statements for Version 2 of the Simple |
| 4633 |
Network Management Protocol (SNMPv2)", <a href="./rfc1904">RFC 1904</a>, January 1996. |
| 4634 |
|
| 4635 |
[<a id="ref-8">8</a>] Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple |
| 4636 |
Network Management Protocol", STD 15, <a href="./rfc1157">RFC 1157</a>, May 1990. |
| 4637 |
|
| 4638 |
[<a id="ref-9">9</a>] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M. and S. |
| 4639 |
Waldbusser, "Introduction to Community-based SNMPv2", <a href="./rfc1901">RFC 1901</a>, |
| 4640 |
January 1996. |
| 4641 |
|
| 4642 |
|
| 4643 |
|
| 4644 |
<span class="grey">Tesink Standards Track [Page 83]</span></pre> |
| 4645 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-84" ></span> |
| 4646 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 4647 |
|
| 4648 |
|
| 4649 |
[<a id="ref-10">10</a>] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M. and S. |
| 4650 |
Waldbusser, "Transport Mappings for Version 2 of the Simple |
| 4651 |
Network Management Protocol (SNMPv2)", <a href="./rfc1906">RFC 1906</a>, January 1996. |
| 4652 |
|
| 4653 |
[<a id="ref-11">11</a>] Case, J., Harrington D., Presuhn R. and B. Wijnen, "Message |
| 4654 |
Processing and Dispatching for the Simple Network Management |
| 4655 |
Protocol (SNMP)", <a href="./rfc2272">RFC 2272</a>, January 1998. |
| 4656 |
|
| 4657 |
[<a id="ref-12">12</a>] Blumenthal, U. and B. Wijnen, "User-based Security Model (USM) |
| 4658 |
for version 3 of the Simple Network Management Protocol |
| 4659 |
(SNMPv3)", <a href="./rfc2274">RFC 2274</a>, January 1998. |
| 4660 |
|
| 4661 |
[<a id="ref-13">13</a>] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M. and S. |
| 4662 |
Waldbusser, "Protocol Operations for Version 2 of the Simple |
| 4663 |
Network Management Protocol (SNMPv2)", <a href="./rfc1905">RFC 1905</a>, January 1996. |
| 4664 |
|
| 4665 |
[<a id="ref-14">14</a>] Levi, D., Meyer, P. and B. Stewart, MPv3 Applications", <a href="./rfc2273">RFC</a> |
| 4666 |
<a href="./rfc2273">2273</a>, January 1998. |
| 4667 |
|
| 4668 |
[<a id="ref-15">15</a>] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based Access |
| 4669 |
Control Model (VACM) for the Simple Network Management Protocol |
| 4670 |
(SNMP)", <a href="./rfc2275">RFC 2275</a>, January 1998. |
| 4671 |
|
| 4672 |
[<a id="ref-16">16</a>] McCloghrie, K. and M. Rose, Editors, "Management Information |
| 4673 |
Base for Network Management of TCP/IP-based internets: MIB-II", |
| 4674 |
STD 17, <a href="./rfc1213">RFC 1213</a>, March 1991. |
| 4675 |
|
| 4676 |
[<a id="ref-17">17</a>] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", |
| 4677 |
<a href="./rfc2233">RFC 2233</a>, November 1997. |
| 4678 |
|
| 4679 |
[<a id="ref-18">18</a>] Brown, T. and K. Tesink, "Definitions of Managed Objects for |
| 4680 |
SMDS Interfaces", <a href="./rfc1694">RFC 1694</a>, May 1994. |
| 4681 |
|
| 4682 |
[<a id="ref-19">19</a>] Noto, M., Spiegel, E. and K. Tesink, Editors, "Definitions of |
| 4683 |
Textual Conventions and OBJECT-IDENTITIES for ATM Management", |
| 4684 |
<a href="./rfc2514">RFC 2514</a>, February 1999. |
| 4685 |
|
| 4686 |
[<a id="ref-20">20</a>] ATM Forum, ATM User-Network Interface, Version 3.0 (UNI 3.0) |
| 4687 |
Specification, 1994. |
| 4688 |
|
| 4689 |
[<a id="ref-21">21</a>] ATM Forum, B-ICI Specification, Version 2.0, af-bici-0013.002, |
| 4690 |
November 1995. |
| 4691 |
|
| 4692 |
[<a id="ref-22">22</a>] "ATM Forum Private Network-Network Interface Specification, |
| 4693 |
Version 1.0 (PNNI 1.0)", af-sig-0055.000, March 1996. |
| 4694 |
|
| 4695 |
[<a id="ref-23">23</a>] "ATM Forum Integrated Local Management Interface (ILMI) |
| 4696 |
Specification", Version 4.0", af-ilmi-0065.000, September 1996. |
| 4697 |
|
| 4698 |
|
| 4699 |
|
| 4700 |
<span class="grey">Tesink Standards Track [Page 84]</span></pre> |
| 4701 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-85" ></span> |
| 4702 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 4703 |
|
| 4704 |
|
| 4705 |
[<a id="ref-24">24</a>] Ahmed, M. and K. Tesink, "Definitions of Managed Objects for ATM |
| 4706 |
Management Version 8.0 using SMIv2", <a href="./rfc1695">RFC 1695</a>, August 1994. |
| 4707 |
|
| 4708 |
<span class="h2"><a class="selflink" id="section-12" href="#section-12">12</a>. Security Considerations</span> |
| 4709 |
|
| 4710 |
There are a number of management objects defined in this MIB that |
| 4711 |
have a MAX-ACCESS clause of read-write and/or read-create. Such |
| 4712 |
objects may be considered sensitive or vulnerable in some network |
| 4713 |
environments. The support for SET operations in a non-secure |
| 4714 |
environment without proper protection can have a negative effect on |
| 4715 |
network operations. |
| 4716 |
|
| 4717 |
The managed objects in this MIB contain sensitive information since, |
| 4718 |
collectively, they allow tracing and influencing of virtual |
| 4719 |
connections in ATM switches or networks and provide information of |
| 4720 |
their traffic characteristics. |
| 4721 |
|
| 4722 |
It is thus important to control even GET access to these objects and |
| 4723 |
possibly to even encrypt the values of these object when sending them |
| 4724 |
over the network via SNMP. Not all versions of SNMP provide features |
| 4725 |
for such a secure environment. |
| 4726 |
|
| 4727 |
SNMPv1 by itself is not a secure environment. Even if the network |
| 4728 |
itself is secure (for example by using IPSec), even then, there is no |
| 4729 |
control as to who on the secure network is allowed to access and |
| 4730 |
GET/SET (read/change/create/delete) the objects in this MIB. |
| 4731 |
|
| 4732 |
It is recommended that the implementers consider the security |
| 4733 |
features as provided by the SNMPv3 framework. Specifically, the use |
| 4734 |
of the User-based Security Model <a href="./rfc2274">RFC 2274</a> [<a href="#ref-12" title=""User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)"">12</a>] and the View-based |
| 4735 |
Access Control Model <a href="./rfc2275">RFC 2275</a> [<a href="#ref-15" title=""View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)"">15</a>] is recommended. |
| 4736 |
|
| 4737 |
It is then a customer/user responsibility to ensure that the SNMP |
| 4738 |
entity giving access to an instance of this MIB, is properly |
| 4739 |
configured to give access to the objects only to those principals |
| 4740 |
(users) that have legitimate rights to indeed GET or SET |
| 4741 |
(change/create/delete) them. |
| 4742 |
|
| 4743 |
<span class="h2"><a class="selflink" id="section-13" href="#section-13">13</a>. Author's Address</span> |
| 4744 |
|
| 4745 |
Kaj Tesink |
| 4746 |
Bellcore |
| 4747 |
331 Newman Springs Road |
| 4748 |
P.O. Box 7020 |
| 4749 |
Red Bank, NJ 07701-7020 |
| 4750 |
|
| 4751 |
Phone: (732) 758-5254 |
| 4752 |
EMail: [email protected] |
| 4753 |
|
| 4754 |
|
| 4755 |
|
| 4756 |
<span class="grey">Tesink Standards Track [Page 85]</span></pre> |
| 4757 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-86" ></span> |
| 4758 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 4759 |
|
| 4760 |
|
| 4761 |
<span class="h2"><a class="selflink" id="section-14" href="#section-14">14</a>. Intellectual Property</span> |
| 4762 |
|
| 4763 |
The IETF takes no position regarding the validity or scope of any |
| 4764 |
intellectual property or other rights that might be claimed to |
| 4765 |
pertain to the implementation or use of the technology described in |
| 4766 |
this document or the extent to which any license under such rights |
| 4767 |
might or might not be available; neither does it represent that it |
| 4768 |
has made any effort to identify any such rights. Information on the |
| 4769 |
IETF's procedures with respect to rights in standards-track and |
| 4770 |
standards-related documentation can be found in <a href="https://www.rfc-editor.org/bcp/bcp11">BCP-11</a>. Copies of |
| 4771 |
claims of rights made available for publication and any assurances of |
| 4772 |
licenses to be made available, or the result of an attempt made to |
| 4773 |
obtain a general license or permission for the use of such |
| 4774 |
proprietary rights by implementors or users of this specification can |
| 4775 |
be obtained from the IETF Secretariat. |
| 4776 |
|
| 4777 |
The IETF invites any interested party to bring to its attention any |
| 4778 |
copyrights, patents or patent applications, or other proprietary |
| 4779 |
rights which may cover technology that may be required to practice |
| 4780 |
this standard. Please address the information to the IETF Executive |
| 4781 |
Director. |
| 4782 |
|
| 4783 |
|
| 4784 |
|
| 4785 |
|
| 4786 |
|
| 4787 |
|
| 4788 |
|
| 4789 |
|
| 4790 |
|
| 4791 |
|
| 4792 |
|
| 4793 |
|
| 4794 |
|
| 4795 |
|
| 4796 |
|
| 4797 |
|
| 4798 |
|
| 4799 |
|
| 4800 |
|
| 4801 |
|
| 4802 |
|
| 4803 |
|
| 4804 |
|
| 4805 |
|
| 4806 |
|
| 4807 |
|
| 4808 |
|
| 4809 |
|
| 4810 |
|
| 4811 |
|
| 4812 |
<span class="grey">Tesink Standards Track [Page 86]</span></pre> |
| 4813 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-87" ></span> |
| 4814 |
<span class="grey"><a href="./rfc2515">RFC 2515</a> ATM Management Objects February 1999</span> |
| 4815 |
|
| 4816 |
|
| 4817 |
<span class="h2"><a class="selflink" id="section-15" href="#section-15">15</a>. Full Copyright Statement</span> |
| 4818 |
|
| 4819 |
Copyright (C) The Internet Society (1999). All Rights Reserved. |
| 4820 |
|
| 4821 |
This document and translations of it may be copied and furnished to |
| 4822 |
others, and derivative works that comment on or otherwise explain it |
| 4823 |
or assist in its implementation may be prepared, copied, published |
| 4824 |
and distributed, in whole or in part, without restriction of any |
| 4825 |
kind, provided that the above copyright notice and this paragraph are |
| 4826 |
included on all such copies and derivative works. However, this |
| 4827 |
document itself may not be modified in any way, such as by removing |
| 4828 |
the copyright notice or references to the Internet Society or other |
| 4829 |
Internet organizations, except as needed for the purpose of |
| 4830 |
developing Internet standards in which case the procedures for |
| 4831 |
copyrights defined in the Internet Standards process must be |
| 4832 |
followed, or as required to translate it into languages other than |
| 4833 |
English. |
| 4834 |
|
| 4835 |
The limited permissions granted above are perpetual and will not be |
| 4836 |
revoked by the Internet Society or its successors or assigns. |
| 4837 |
|
| 4838 |
This document and the information contained herein is provided on an |
| 4839 |
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING |
| 4840 |
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING |
| 4841 |
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION |
| 4842 |
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF |
| 4843 |
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. |
| 4844 |
|
| 4845 |
|
| 4846 |
|
| 4847 |
|
| 4848 |
|
| 4849 |
|
| 4850 |
|
| 4851 |
|
| 4852 |
|
| 4853 |
|
| 4854 |
|
| 4855 |
|
| 4856 |
|
| 4857 |
|
| 4858 |
|
| 4859 |
|
| 4860 |
|
| 4861 |
|
| 4862 |
|
| 4863 |
|
| 4864 |
|
| 4865 |
|
| 4866 |
|
| 4867 |
|
| 4868 |
Tesink Standards Track [Page 87] |
| 4869 |
</pre> |