| 1 |
<pre>Network Working Group K. McCloghrie |
| 2 |
Request for Comments: 1748 E. Decker |
| 3 |
Obsoletes: <a href="./rfc1743">1743</a>, <a href="./rfc1231">1231</a> cisco Systems, Inc. |
| 4 |
Category: Standards Track December 1994 |
| 5 |
|
| 6 |
|
| 7 |
<span class="h1">IEEE 802.5 MIB using SMIv2</span> |
| 8 |
|
| 9 |
Status of this Memo |
| 10 |
|
| 11 |
This document specifies an Internet standards track protocol for the |
| 12 |
Internet community, and requests discussion and suggestions for |
| 13 |
improvements. Please refer to the current edition of the "Internet |
| 14 |
Official Protocol Standards" (STD 1) for the standardization state |
| 15 |
and status of this protocol. Distribution of this memo is unlimited. |
| 16 |
|
| 17 |
Table of Contents |
| 18 |
|
| 19 |
<a href="#section-1">1</a>. Introduction ............................................. <a href="#page-1">1</a> |
| 20 |
<a href="#section-2">2</a>. The SNMPv2 Network Management Framework .................. <a href="#page-2">2</a> |
| 21 |
<a href="#section-2.1">2.1</a> Object Definitions ...................................... <a href="#page-2">2</a> |
| 22 |
<a href="#section-3">3</a>. Overview ................................................. <a href="#page-2">2</a> |
| 23 |
<a href="#section-3.1">3.1</a> MAC Addresses ........................................... <a href="#page-3">3</a> |
| 24 |
<a href="#section-3.2">3.2</a> Relationship to <a href="./rfc1213">RFC 1213</a> ................................ <a href="#page-3">3</a> |
| 25 |
<a href="#section-3.3">3.3</a> Relationship to <a href="./rfc1573">RFC 1573</a> ................................ <a href="#page-3">3</a> |
| 26 |
<a href="#section-3.3.1">3.3.1</a> Layering Model ........................................ <a href="#page-3">3</a> |
| 27 |
<a href="#section-3.3.2">3.3.2</a> Virtual Circuits ...................................... <a href="#page-3">3</a> |
| 28 |
<a href="#section-3.3.3">3.3.3</a> ifTestTable ........................................... <a href="#page-3">3</a> |
| 29 |
<a href="#section-3.3.4">3.3.4</a> ifRcvAddressTable ..................................... <a href="#page-4">4</a> |
| 30 |
<a href="#section-3.3.5">3.3.5</a> ifPhysAddress ......................................... <a href="#page-4">4</a> |
| 31 |
<a href="#section-3.3.6">3.3.6</a> ifType ................................................ <a href="#page-4">4</a> |
| 32 |
<a href="#section-4">4</a>. Definitions .............................................. <a href="#page-4">4</a> |
| 33 |
<a href="#section-5">5</a>. Acknowledgements ......................................... <a href="#page-23">23</a> |
| 34 |
<a href="#section-6">6</a>. References ............................................... <a href="#page-23">23</a> |
| 35 |
<a href="#appendix-A">Appendix A</a>. Changes from <a href="./rfc1231">RFC 1231</a> ........................... <a href="#page-24">24</a> |
| 36 |
Security Considerations ..................................... <a href="#page-24">24</a> |
| 37 |
Authors' Addresses .......................................... <a href="#page-25">25</a> |
| 38 |
|
| 39 |
<span class="h2"><a class="selflink" id="section-1" href="#section-1">1</a>. Introduction</span> |
| 40 |
|
| 41 |
This memo defines a portion of the Management Information Base (MIB) |
| 42 |
for use with network management protocols in the Internet community. |
| 43 |
In particular, it describes managed objects used for managing |
| 44 |
subnetworks which use the IEEE 802.5 Token Ring technology described |
| 45 |
in 802.5 Token Ring Access Method and Physical Layer Specifications, |
| 46 |
IEEE Standard 802.5-1989 [<a href="#ref-7" title=""Token Ring Access Method and Physical Layer Specifications"">7</a>]. This memo is a replacement for <a href="./rfc1231">RFC</a> |
| 47 |
<a href="./rfc1231">1231</a>. |
| 48 |
|
| 49 |
|
| 50 |
|
| 51 |
|
| 52 |
<span class="grey">McCloghrie & Decker [Page 1]</span></pre> |
| 53 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-2" ></span> |
| 54 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 55 |
|
| 56 |
|
| 57 |
<span class="h2"><a class="selflink" id="section-2" href="#section-2">2</a>. The SNMPv2 Network Management Framework</span> |
| 58 |
|
| 59 |
The SNMPv2 Network Management Framework consists of four major |
| 60 |
components. They are: |
| 61 |
|
| 62 |
o <a href="./rfc1442">RFC 1442</a> [<a href="#ref-1" title=""Structure of Management Information for version 2 of the Simple Network Management Protocol (SNMPv2)"">1</a>] which defines the SMI, the mechanisms used for |
| 63 |
describing and naming objects for the purpose of management. |
| 64 |
|
| 65 |
o STD 17, <a href="./rfc1213">RFC 1213</a> [<a href="#ref-2" title=""Management Information Base for Network Management of TCP/IP-based internets: MIB-II"">2</a>] defines MIB-II, the core set of managed |
| 66 |
objects for the Internet suite of protocols. |
| 67 |
|
| 68 |
o <a href="./rfc1445">RFC 1445</a> [<a href="#ref-3" title=""Administrative Model for version 2 of the Simple Network Management Protocol (SNMPv2)"">3</a>] which defines the administrative and other |
| 69 |
architectural aspects of the framework. |
| 70 |
|
| 71 |
o <a href="./rfc1448">RFC 1448</a> [<a href="#ref-4" title=""Protocol Operations for version 2 of the Simple Network Management Protocol (SNMPv2)"">4</a>] which defines the protocol used for network |
| 72 |
access to managed objects. |
| 73 |
|
| 74 |
The Framework permits new objects to be defined for the purpose of |
| 75 |
experimentation and evaluation. |
| 76 |
|
| 77 |
<span class="h3"><a class="selflink" id="section-2.1" href="#section-2.1">2.1</a>. Object Definitions</span> |
| 78 |
|
| 79 |
Managed objects are accessed via a virtual information store, termed |
| 80 |
the Management Information Base or MIB. Objects in the MIB are |
| 81 |
defined using the subset of Abstract Syntax Notation One (ASN.1) |
| 82 |
defined in the SMI. In particular, each object type is named by an |
| 83 |
OBJECT IDENTIFIER, an administratively assigned name. The object |
| 84 |
type together with an object instance serves to uniquely identify a |
| 85 |
specific instantiation of the object. For human convenience, we |
| 86 |
often use a textual string, termed the descriptor, to refer to the |
| 87 |
object type. |
| 88 |
|
| 89 |
<span class="h2"><a class="selflink" id="section-3" href="#section-3">3</a>. Overview</span> |
| 90 |
|
| 91 |
This memo defines three tables: the 802.5 Interface Table, which |
| 92 |
contains state and parameter information which is specific to 802.5 |
| 93 |
interfaces, the 802.5 Statistics Table, which contains 802.5 |
| 94 |
interface statistics, and the 802.5 Timer Table, which contains the |
| 95 |
values of 802.5-defined timers. A managed system will have one entry |
| 96 |
in the 802.5 Interface Table and one entry in the 802.5 Statistics |
| 97 |
Table for each of its 802.5 interfaces. The 802.5 Timer Table is |
| 98 |
obsolete, but its definition has been retained in this memo for |
| 99 |
backward compatibility. |
| 100 |
|
| 101 |
This memo also defines OBJECT IDENTIFIERs, some to identify interface |
| 102 |
tests for use with the ifTestTable [<a href="#ref-6" title=""Evolution of the Interfaces Group of MIB-II"">6</a>], and some to identify Token |
| 103 |
Ring interface Chip Sets. |
| 104 |
|
| 105 |
|
| 106 |
|
| 107 |
|
| 108 |
<span class="grey">McCloghrie & Decker [Page 2]</span></pre> |
| 109 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-3" ></span> |
| 110 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 111 |
|
| 112 |
|
| 113 |
<span class="h3"><a class="selflink" id="section-3.1" href="#section-3.1">3.1</a>. MAC Addresses</span> |
| 114 |
|
| 115 |
All representations of MAC addresses in this MIB Module use the |
| 116 |
MacAddress textual convention [<a href="#ref-5" title=""Textual Conventions for version 2 of the Simple Network Management Protocol (SNMPv2)"">5</a>] for which the address is in the |
| 117 |
"canonical" order defined by IEEE 802.1a, i.e., as if it were |
| 118 |
transmitted least significant bit first, even though 802.5 requires |
| 119 |
MAC addresses to be transmitted most significant bit first. |
| 120 |
|
| 121 |
16-bit addresses, if needed, are represented by setting their upper 4 |
| 122 |
octets to all zeros, i.e., AAFF would be represented as 00000000AAFF. |
| 123 |
|
| 124 |
<span class="h3"><a class="selflink" id="section-3.2" href="#section-3.2">3.2</a>. Relationship to <a href="./rfc1213">RFC 1213</a></span> |
| 125 |
|
| 126 |
When this MIB module is used in conjunction with the "old" (i.e., |
| 127 |
pre-RFC 1573) interfaces group, the relationship between an 802.5 |
| 128 |
interface and an interface in the context of the <a href="./rfc1213">RFC 1213</a> is one- |
| 129 |
to-one. That is, the value of an ifIndex object instance for an |
| 130 |
802.5 interface can be directly used to identify corresponding |
| 131 |
instances of the objects defined in this memo. |
| 132 |
|
| 133 |
<span class="h3"><a class="selflink" id="section-3.3" href="#section-3.3">3.3</a>. Relationship to <a href="./rfc1573">RFC 1573</a></span> |
| 134 |
|
| 135 |
<a href="./rfc1573">RFC 1573</a>, the Interface MIB Evolution, requires that any MIB module |
| 136 |
which is an adjunct of the Interface MIB, clarify specific areas |
| 137 |
within the Interface MIB. These areas were intentionally left vague |
| 138 |
in <a href="./rfc1573">RFC 1573</a> to avoid over constraining the MIB module, thereby |
| 139 |
precluding management of certain media-types. |
| 140 |
|
| 141 |
<a href="./rfc1573#section-3.3">Section 3.3 of RFC 1573</a> enumerates several areas which a media- |
| 142 |
specific MIB module must clarify. Each of these areas is addressed |
| 143 |
in a following subsection. The implementor is referred to <a href="./rfc1573">RFC 1573</a> |
| 144 |
in order to understand the general intent of these areas. |
| 145 |
|
| 146 |
<span class="h4"><a class="selflink" id="section-3.3.1" href="#section-3.3.1">3.3.1</a>. Layering Model</span> |
| 147 |
|
| 148 |
For the typical usage of this IEEE 802.5 MIB module, there will be no |
| 149 |
sub-layers "above" or "below" the 802.5 interface. However, this MIB |
| 150 |
module does not preclude such layering. |
| 151 |
|
| 152 |
<span class="h4"><a class="selflink" id="section-3.3.2" href="#section-3.3.2">3.3.2</a>. Virtual Circuits</span> |
| 153 |
|
| 154 |
802.5 does not support virtual circuits. |
| 155 |
|
| 156 |
<span class="h4"><a class="selflink" id="section-3.3.3" href="#section-3.3.3">3.3.3</a>. ifTestTable</span> |
| 157 |
|
| 158 |
This MIB module defines two tests for 802.5 interfaces: Insertion and |
| 159 |
Loopback. Implementation of these tests is not required. |
| 160 |
|
| 161 |
|
| 162 |
|
| 163 |
|
| 164 |
<span class="grey">McCloghrie & Decker [Page 3]</span></pre> |
| 165 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-4" ></span> |
| 166 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 167 |
|
| 168 |
|
| 169 |
<span class="h4"><a class="selflink" id="section-3.3.4" href="#section-3.3.4">3.3.4</a>. ifRcvAddressTable</span> |
| 170 |
|
| 171 |
The ifRcvAddressTable is defined to contains all MAC addresses, |
| 172 |
unicast, multicast (group) and broadcast, for which an interface will |
| 173 |
receive packets. For 802.5 interfaces, its use includes functional |
| 174 |
addresses. The format of the address, contained in |
| 175 |
ifRcvAddressAddress, is the same as for ifPhysAddress. |
| 176 |
|
| 177 |
For functional addresses on a particular 802.5 interface, only one |
| 178 |
ifRcvAddressTable entry is required. That entry is the one for the |
| 179 |
address which has the functional address bit ANDed with the bit mask |
| 180 |
of all functional addresses for which the interface will accept |
| 181 |
frames. |
| 182 |
|
| 183 |
<span class="h4"><a class="selflink" id="section-3.3.5" href="#section-3.3.5">3.3.5</a>. ifPhysAddress</span> |
| 184 |
|
| 185 |
For an 802.5 interface, ifPhysAddress contains the interface's IEEE |
| 186 |
MAC address, stored as an octet string of length 6, in IEEE 802.1a |
| 187 |
"canonical" order, i.e., the Group Bit is positioned as the low-order |
| 188 |
bit (0x01) of the first octet. |
| 189 |
|
| 190 |
<span class="h4"><a class="selflink" id="section-3.3.6" href="#section-3.3.6">3.3.6</a>. ifType</span> |
| 191 |
|
| 192 |
The objects defined in this memo apply to each interface for which |
| 193 |
the ifType has the value: |
| 194 |
|
| 195 |
iso88025-tokenRing(9) |
| 196 |
|
| 197 |
<span class="h2"><a class="selflink" id="section-4" href="#section-4">4</a>. Definitions</span> |
| 198 |
|
| 199 |
TOKENRING-MIB DEFINITIONS ::= BEGIN |
| 200 |
|
| 201 |
IMPORTS |
| 202 |
MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY, |
| 203 |
Counter32, Integer32 FROM SNMPv2-SMI |
| 204 |
transmission FROM <a href="./rfc1213">RFC1213</a>-MIB |
| 205 |
MacAddress,TimeStamp FROM SNMPv2-TC |
| 206 |
MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF; |
| 207 |
|
| 208 |
dot5 MODULE-IDENTITY |
| 209 |
LAST-UPDATED "9410231150Z" |
| 210 |
ORGANIZATION "IETF Interfaces MIB Working Group" |
| 211 |
CONTACT-INFO |
| 212 |
" Keith McCloghrie |
| 213 |
|
| 214 |
Postal: cisco Systems, Inc. |
| 215 |
170 West Tasman Drive, |
| 216 |
San Jose, CA 95134-1706 |
| 217 |
|
| 218 |
|
| 219 |
|
| 220 |
<span class="grey">McCloghrie & Decker [Page 4]</span></pre> |
| 221 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-5" ></span> |
| 222 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 223 |
|
| 224 |
|
| 225 |
US |
| 226 |
|
| 227 |
Phone: +1 408 526 5260 |
| 228 |
EMail: [email protected]" |
| 229 |
DESCRIPTION |
| 230 |
"The MIB module for IEEE Token Ring entities." |
| 231 |
::= { transmission 9 } |
| 232 |
|
| 233 |
|
| 234 |
-- The 802.5 Interface Table |
| 235 |
|
| 236 |
-- This table contains state and parameter information which |
| 237 |
-- is specific to 802.5 interfaces. It is mandatory that |
| 238 |
-- systems having 802.5 interfaces implement this table in |
| 239 |
-- addition to the ifTable (see RFCs 1213 and 1573). |
| 240 |
|
| 241 |
dot5Table OBJECT-TYPE |
| 242 |
SYNTAX SEQUENCE OF Dot5Entry |
| 243 |
MAX-ACCESS not-accessible |
| 244 |
STATUS current |
| 245 |
DESCRIPTION |
| 246 |
"This table contains Token Ring interface |
| 247 |
parameters and state variables, one entry |
| 248 |
per 802.5 interface." |
| 249 |
::= { dot5 1 } |
| 250 |
|
| 251 |
dot5Entry OBJECT-TYPE |
| 252 |
SYNTAX Dot5Entry |
| 253 |
MAX-ACCESS not-accessible |
| 254 |
STATUS current |
| 255 |
DESCRIPTION |
| 256 |
"A list of Token Ring status and parameter |
| 257 |
values for an 802.5 interface." |
| 258 |
INDEX { dot5IfIndex } |
| 259 |
::= { dot5Table 1 } |
| 260 |
|
| 261 |
Dot5Entry ::= SEQUENCE { |
| 262 |
dot5IfIndex Integer32, |
| 263 |
dot5Commands INTEGER, |
| 264 |
dot5RingStatus INTEGER, |
| 265 |
dot5RingState INTEGER, |
| 266 |
dot5RingOpenStatus INTEGER, |
| 267 |
dot5RingSpeed INTEGER, |
| 268 |
dot5UpStream MacAddress, |
| 269 |
dot5ActMonParticipate INTEGER, |
| 270 |
dot5Functional MacAddress, |
| 271 |
dot5LastBeaconSent TimeStamp |
| 272 |
} |
| 273 |
|
| 274 |
|
| 275 |
|
| 276 |
<span class="grey">McCloghrie & Decker [Page 5]</span></pre> |
| 277 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-6" ></span> |
| 278 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 279 |
|
| 280 |
|
| 281 |
dot5IfIndex OBJECT-TYPE |
| 282 |
SYNTAX Integer32 |
| 283 |
MAX-ACCESS read-only |
| 284 |
STATUS current |
| 285 |
DESCRIPTION |
| 286 |
"The value of this object identifies the |
| 287 |
802.5 interface for which this entry |
| 288 |
contains management information. The |
| 289 |
value of this object for a particular |
| 290 |
interface has the same value as the |
| 291 |
ifIndex object, defined in MIB-II for |
| 292 |
the same interface." |
| 293 |
::= { dot5Entry 1 } |
| 294 |
|
| 295 |
dot5Commands OBJECT-TYPE |
| 296 |
SYNTAX INTEGER { |
| 297 |
noop(1), |
| 298 |
open(2), |
| 299 |
reset(3), |
| 300 |
close(4) |
| 301 |
} |
| 302 |
MAX-ACCESS read-write |
| 303 |
STATUS current |
| 304 |
DESCRIPTION |
| 305 |
"When this object is set to the value of |
| 306 |
open(2), the station should go into the |
| 307 |
open state. The progress and success of |
| 308 |
the open is given by the values of the |
| 309 |
objects dot5RingState and |
| 310 |
dot5RingOpenStatus. |
| 311 |
When this object is set to the value |
| 312 |
of reset(3), then the station should do |
| 313 |
a reset. On a reset, all MIB counters |
| 314 |
should retain their values, if possible. |
| 315 |
Other side affects are dependent on the |
| 316 |
hardware chip set. |
| 317 |
When this object is set to the value |
| 318 |
of close(4), the station should go into |
| 319 |
the stopped state by removing itself |
| 320 |
from the ring. |
| 321 |
Setting this object to a value of |
| 322 |
noop(1) has no effect. |
| 323 |
When read, this object always has a |
| 324 |
value of noop(1). |
| 325 |
The open(2) and close(4) values |
| 326 |
correspond to the up(1) and down(2) values |
| 327 |
of MIB-II's ifAdminStatus and ifOperStatus, |
| 328 |
i.e., the setting of ifAdminStatus and |
| 329 |
|
| 330 |
|
| 331 |
|
| 332 |
<span class="grey">McCloghrie & Decker [Page 6]</span></pre> |
| 333 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-7" ></span> |
| 334 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 335 |
|
| 336 |
|
| 337 |
dot5Commands affects the values of both |
| 338 |
dot5Commands and ifOperStatus." |
| 339 |
::= { dot5Entry 2 } |
| 340 |
|
| 341 |
dot5RingStatus OBJECT-TYPE |
| 342 |
SYNTAX INTEGER (0..262143) |
| 343 |
MAX-ACCESS read-only |
| 344 |
STATUS current |
| 345 |
DESCRIPTION |
| 346 |
"The current interface status which can |
| 347 |
be used to diagnose fluctuating problems |
| 348 |
that can occur on token rings, after a |
| 349 |
station has successfully been added to |
| 350 |
the ring. |
| 351 |
Before an open is completed, this |
| 352 |
object has the value for the 'no status' |
| 353 |
condition. The dot5RingState and |
| 354 |
dot5RingOpenStatus objects provide for |
| 355 |
debugging problems when the station |
| 356 |
can not even enter the ring. |
| 357 |
The object's value is a sum of |
| 358 |
values, one for each currently applicable |
| 359 |
condition. The following values are |
| 360 |
defined for various conditions: |
| 361 |
|
| 362 |
0 = No Problems detected |
| 363 |
32 = Ring Recovery |
| 364 |
64 = Single Station |
| 365 |
256 = Remove Received |
| 366 |
512 = reserved |
| 367 |
1024 = Auto-Removal Error |
| 368 |
2048 = Lobe Wire Fault |
| 369 |
4096 = Transmit Beacon |
| 370 |
8192 = Soft Error |
| 371 |
16384 = Hard Error |
| 372 |
32768 = Signal Loss |
| 373 |
131072 = no status, open not completed." |
| 374 |
::= { dot5Entry 3 } |
| 375 |
|
| 376 |
dot5RingState OBJECT-TYPE |
| 377 |
SYNTAX INTEGER { |
| 378 |
opened(1), |
| 379 |
closed(2), |
| 380 |
opening(3), |
| 381 |
closing(4), |
| 382 |
openFailure(5), |
| 383 |
ringFailure(6) |
| 384 |
} |
| 385 |
|
| 386 |
|
| 387 |
|
| 388 |
<span class="grey">McCloghrie & Decker [Page 7]</span></pre> |
| 389 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-8" ></span> |
| 390 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 391 |
|
| 392 |
|
| 393 |
MAX-ACCESS read-only |
| 394 |
STATUS current |
| 395 |
DESCRIPTION |
| 396 |
"The current interface state with respect |
| 397 |
to entering or leaving the ring." |
| 398 |
::= { dot5Entry 4 } |
| 399 |
|
| 400 |
dot5RingOpenStatus OBJECT-TYPE |
| 401 |
SYNTAX INTEGER { |
| 402 |
noOpen(1), -- no open attempted |
| 403 |
badParam(2), |
| 404 |
lobeFailed(3), |
| 405 |
signalLoss(4), |
| 406 |
insertionTimeout(5), |
| 407 |
ringFailed(6), |
| 408 |
beaconing(7), |
| 409 |
duplicateMAC(8), |
| 410 |
requestFailed(9), |
| 411 |
removeReceived(10), |
| 412 |
open(11) -- last open successful |
| 413 |
} |
| 414 |
MAX-ACCESS read-only |
| 415 |
STATUS current |
| 416 |
DESCRIPTION |
| 417 |
"This object indicates the success, or the |
| 418 |
reason for failure, of the station's most |
| 419 |
recent attempt to enter the ring." |
| 420 |
::= { dot5Entry 5 } |
| 421 |
|
| 422 |
dot5RingSpeed OBJECT-TYPE |
| 423 |
SYNTAX INTEGER { |
| 424 |
unknown(1), |
| 425 |
oneMegabit(2), |
| 426 |
fourMegabit(3), |
| 427 |
sixteenMegabit(4) |
| 428 |
} |
| 429 |
MAX-ACCESS read-write |
| 430 |
STATUS current |
| 431 |
DESCRIPTION |
| 432 |
"The ring-speed at the next insertion into |
| 433 |
the ring. Note that this may or may not be |
| 434 |
different to the current ring-speed which is |
| 435 |
given by MIB-II's ifSpeed. For interfaces |
| 436 |
which do not support changing ring-speed, |
| 437 |
dot5RingSpeed can only be set to its current |
| 438 |
value. When dot5RingSpeed has the value |
| 439 |
unknown(1), the ring's actual ring-speed is |
| 440 |
to be used." |
| 441 |
|
| 442 |
|
| 443 |
|
| 444 |
<span class="grey">McCloghrie & Decker [Page 8]</span></pre> |
| 445 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-9" ></span> |
| 446 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 447 |
|
| 448 |
|
| 449 |
::= { dot5Entry 6 } |
| 450 |
|
| 451 |
dot5UpStream OBJECT-TYPE |
| 452 |
SYNTAX MacAddress |
| 453 |
MAX-ACCESS read-only |
| 454 |
STATUS current |
| 455 |
DESCRIPTION |
| 456 |
"The MAC-address of the up stream neighbor |
| 457 |
station in the ring." |
| 458 |
::= { dot5Entry 7 } |
| 459 |
|
| 460 |
dot5ActMonParticipate OBJECT-TYPE |
| 461 |
SYNTAX INTEGER { |
| 462 |
true(1), |
| 463 |
false(2) |
| 464 |
} |
| 465 |
MAX-ACCESS read-write |
| 466 |
STATUS current |
| 467 |
DESCRIPTION |
| 468 |
"If this object has a value of true(1) then |
| 469 |
this interface will participate in the |
| 470 |
active monitor selection process. If the |
| 471 |
value is false(2) then it will not. |
| 472 |
Setting this object does not take effect |
| 473 |
until the next Active Monitor election, and |
| 474 |
might not take effect until the next time |
| 475 |
the interface is opened." |
| 476 |
::= { dot5Entry 8 } |
| 477 |
|
| 478 |
dot5Functional OBJECT-TYPE |
| 479 |
SYNTAX MacAddress |
| 480 |
MAX-ACCESS read-write |
| 481 |
STATUS current |
| 482 |
DESCRIPTION |
| 483 |
"The bit mask of all Token Ring functional |
| 484 |
addresses for which this interface will |
| 485 |
accept frames." |
| 486 |
::= { dot5Entry 9 } |
| 487 |
|
| 488 |
dot5LastBeaconSent OBJECT-TYPE |
| 489 |
SYNTAX TimeStamp |
| 490 |
MAX-ACCESS read-only |
| 491 |
STATUS current |
| 492 |
DESCRIPTION |
| 493 |
"The value of MIB-II's sysUpTime object at which |
| 494 |
the local system last transmitted a Beacon frame |
| 495 |
on this interface." |
| 496 |
::= { dot5Entry 10 } |
| 497 |
|
| 498 |
|
| 499 |
|
| 500 |
<span class="grey">McCloghrie & Decker [Page 9]</span></pre> |
| 501 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-10" ></span> |
| 502 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 503 |
|
| 504 |
|
| 505 |
-- The 802.5 Statistics Table |
| 506 |
|
| 507 |
-- This table contains statistics and error counter which are |
| 508 |
-- specific to 802.5 interfaces. It is mandatory that systems |
| 509 |
-- having 802.5 interfaces implement this table. |
| 510 |
|
| 511 |
dot5StatsTable OBJECT-TYPE |
| 512 |
SYNTAX SEQUENCE OF Dot5StatsEntry |
| 513 |
MAX-ACCESS not-accessible |
| 514 |
STATUS current |
| 515 |
DESCRIPTION |
| 516 |
"A table containing Token Ring statistics, |
| 517 |
one entry per 802.5 interface. |
| 518 |
All the statistics are defined using |
| 519 |
the syntax Counter32 as 32-bit wrap around |
| 520 |
counters. Thus, if an interface's |
| 521 |
hardware maintains these statistics in |
| 522 |
16-bit counters, then the agent must read |
| 523 |
the hardware's counters frequently enough |
| 524 |
to prevent loss of significance, in order |
| 525 |
to maintain 32-bit counters in software." |
| 526 |
::= { dot5 2 } |
| 527 |
|
| 528 |
dot5StatsEntry OBJECT-TYPE |
| 529 |
SYNTAX Dot5StatsEntry |
| 530 |
MAX-ACCESS not-accessible |
| 531 |
STATUS current |
| 532 |
DESCRIPTION |
| 533 |
"An entry contains the 802.5 statistics |
| 534 |
for a particular interface." |
| 535 |
INDEX { dot5StatsIfIndex } |
| 536 |
::= { dot5StatsTable 1 } |
| 537 |
|
| 538 |
|
| 539 |
Dot5StatsEntry ::= SEQUENCE { |
| 540 |
dot5StatsIfIndex Integer32, |
| 541 |
dot5StatsLineErrors Counter32, |
| 542 |
dot5StatsBurstErrors Counter32, |
| 543 |
dot5StatsACErrors Counter32, |
| 544 |
dot5StatsAbortTransErrors Counter32, |
| 545 |
dot5StatsInternalErrors Counter32, |
| 546 |
dot5StatsLostFrameErrors Counter32, |
| 547 |
dot5StatsReceiveCongestions Counter32, |
| 548 |
dot5StatsFrameCopiedErrors Counter32, |
| 549 |
dot5StatsTokenErrors Counter32, |
| 550 |
dot5StatsSoftErrors Counter32, |
| 551 |
dot5StatsHardErrors Counter32, |
| 552 |
dot5StatsSignalLoss Counter32, |
| 553 |
|
| 554 |
|
| 555 |
|
| 556 |
<span class="grey">McCloghrie & Decker [Page 10]</span></pre> |
| 557 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-11" ></span> |
| 558 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 559 |
|
| 560 |
|
| 561 |
dot5StatsTransmitBeacons Counter32, |
| 562 |
dot5StatsRecoverys Counter32, |
| 563 |
dot5StatsLobeWires Counter32, |
| 564 |
dot5StatsRemoves Counter32, |
| 565 |
dot5StatsSingles Counter32, |
| 566 |
dot5StatsFreqErrors Counter32 |
| 567 |
} |
| 568 |
|
| 569 |
|
| 570 |
dot5StatsIfIndex OBJECT-TYPE |
| 571 |
SYNTAX Integer32 |
| 572 |
MAX-ACCESS read-only |
| 573 |
STATUS current |
| 574 |
DESCRIPTION |
| 575 |
"The value of this object identifies the |
| 576 |
802.5 interface for which this entry |
| 577 |
contains management information. The |
| 578 |
value of this object for a particular |
| 579 |
interface has the same value as MIB-II's |
| 580 |
ifIndex object for the same interface." |
| 581 |
::= { dot5StatsEntry 1 } |
| 582 |
|
| 583 |
dot5StatsLineErrors OBJECT-TYPE |
| 584 |
SYNTAX Counter32 |
| 585 |
MAX-ACCESS read-only |
| 586 |
STATUS current |
| 587 |
DESCRIPTION |
| 588 |
"This counter is incremented when a frame |
| 589 |
or token is copied or repeated by a |
| 590 |
station, the E bit is zero in the frame |
| 591 |
or token and one of the following |
| 592 |
conditions exists: 1) there is a |
| 593 |
non-data bit (J or K bit) between the SD |
| 594 |
and the ED of the frame or token, or |
| 595 |
2) there is an FCS error in the frame." |
| 596 |
::= { dot5StatsEntry 2 } |
| 597 |
|
| 598 |
dot5StatsBurstErrors OBJECT-TYPE |
| 599 |
SYNTAX Counter32 |
| 600 |
MAX-ACCESS read-only |
| 601 |
STATUS current |
| 602 |
DESCRIPTION |
| 603 |
"This counter is incremented when a station |
| 604 |
detects the absence of transitions for five |
| 605 |
half-bit timers (burst-five error)." |
| 606 |
::= { dot5StatsEntry 3 } |
| 607 |
|
| 608 |
|
| 609 |
|
| 610 |
|
| 611 |
|
| 612 |
<span class="grey">McCloghrie & Decker [Page 11]</span></pre> |
| 613 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-12" ></span> |
| 614 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 615 |
|
| 616 |
|
| 617 |
dot5StatsACErrors OBJECT-TYPE |
| 618 |
SYNTAX Counter32 |
| 619 |
MAX-ACCESS read-only |
| 620 |
STATUS current |
| 621 |
DESCRIPTION |
| 622 |
"This counter is incremented when a station |
| 623 |
receives an AMP or SMP frame in which A is |
| 624 |
equal to C is equal to 0, and then receives |
| 625 |
another SMP frame with A is equal to C is |
| 626 |
equal to 0 without first receiving an AMP |
| 627 |
frame. It denotes a station that cannot set |
| 628 |
the AC bits properly." |
| 629 |
::= { dot5StatsEntry 4 } |
| 630 |
|
| 631 |
dot5StatsAbortTransErrors OBJECT-TYPE |
| 632 |
SYNTAX Counter32 |
| 633 |
MAX-ACCESS read-only |
| 634 |
STATUS current |
| 635 |
DESCRIPTION |
| 636 |
"This counter is incremented when a station |
| 637 |
transmits an abort delimiter while |
| 638 |
transmitting." |
| 639 |
::= { dot5StatsEntry 5 } |
| 640 |
|
| 641 |
dot5StatsInternalErrors OBJECT-TYPE |
| 642 |
SYNTAX Counter32 |
| 643 |
MAX-ACCESS read-only |
| 644 |
STATUS current |
| 645 |
DESCRIPTION |
| 646 |
"This counter is incremented when a station |
| 647 |
recognizes an internal error." |
| 648 |
::= { dot5StatsEntry 6 } |
| 649 |
|
| 650 |
dot5StatsLostFrameErrors OBJECT-TYPE |
| 651 |
SYNTAX Counter32 |
| 652 |
MAX-ACCESS read-only |
| 653 |
STATUS current |
| 654 |
DESCRIPTION |
| 655 |
"This counter is incremented when a station |
| 656 |
is transmitting and its TRR timer expires. |
| 657 |
This condition denotes a condition where a |
| 658 |
transmitting station in strip mode does not |
| 659 |
receive the trailer of the frame before the |
| 660 |
TRR timer goes off." |
| 661 |
::= { dot5StatsEntry 7 } |
| 662 |
|
| 663 |
|
| 664 |
|
| 665 |
|
| 666 |
|
| 667 |
|
| 668 |
<span class="grey">McCloghrie & Decker [Page 12]</span></pre> |
| 669 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-13" ></span> |
| 670 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 671 |
|
| 672 |
|
| 673 |
dot5StatsReceiveCongestions OBJECT-TYPE |
| 674 |
SYNTAX Counter32 |
| 675 |
MAX-ACCESS read-only |
| 676 |
STATUS current |
| 677 |
DESCRIPTION |
| 678 |
"This counter is incremented when a station |
| 679 |
recognizes a frame addressed to its |
| 680 |
specific address, but has no available |
| 681 |
buffer space indicating that the station |
| 682 |
is congested." |
| 683 |
::= { dot5StatsEntry 8 } |
| 684 |
|
| 685 |
dot5StatsFrameCopiedErrors OBJECT-TYPE |
| 686 |
SYNTAX Counter32 |
| 687 |
MAX-ACCESS read-only |
| 688 |
STATUS current |
| 689 |
DESCRIPTION |
| 690 |
"This counter is incremented when a station |
| 691 |
recognizes a frame addressed to its |
| 692 |
specific address and detects that the FS |
| 693 |
field A bits are set to 1 indicating a |
| 694 |
possible line hit or duplicate address." |
| 695 |
::= { dot5StatsEntry 9 } |
| 696 |
|
| 697 |
dot5StatsTokenErrors OBJECT-TYPE |
| 698 |
SYNTAX Counter32 |
| 699 |
MAX-ACCESS read-only |
| 700 |
STATUS current |
| 701 |
DESCRIPTION |
| 702 |
"This counter is incremented when a station |
| 703 |
acting as the active monitor recognizes an |
| 704 |
error condition that needs a token |
| 705 |
transmitted." |
| 706 |
::= { dot5StatsEntry 10 } |
| 707 |
|
| 708 |
dot5StatsSoftErrors OBJECT-TYPE |
| 709 |
SYNTAX Counter32 |
| 710 |
MAX-ACCESS read-only |
| 711 |
STATUS current |
| 712 |
DESCRIPTION |
| 713 |
"The number of Soft Errors the interface |
| 714 |
has detected. It directly corresponds to |
| 715 |
the number of Report Error MAC frames |
| 716 |
that this interface has transmitted. |
| 717 |
Soft Errors are those which are |
| 718 |
recoverable by the MAC layer protocols." |
| 719 |
::= { dot5StatsEntry 11 } |
| 720 |
|
| 721 |
|
| 722 |
|
| 723 |
|
| 724 |
<span class="grey">McCloghrie & Decker [Page 13]</span></pre> |
| 725 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-14" ></span> |
| 726 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 727 |
|
| 728 |
|
| 729 |
dot5StatsHardErrors OBJECT-TYPE |
| 730 |
SYNTAX Counter32 |
| 731 |
MAX-ACCESS read-only |
| 732 |
STATUS current |
| 733 |
DESCRIPTION |
| 734 |
"The number of times this interface has |
| 735 |
detected an immediately recoverable |
| 736 |
fatal error. It denotes the number of |
| 737 |
times this interface is either |
| 738 |
transmitting or receiving beacon MAC |
| 739 |
frames." |
| 740 |
::= { dot5StatsEntry 12 } |
| 741 |
|
| 742 |
dot5StatsSignalLoss OBJECT-TYPE |
| 743 |
SYNTAX Counter32 |
| 744 |
MAX-ACCESS read-only |
| 745 |
STATUS current |
| 746 |
DESCRIPTION |
| 747 |
"The number of times this interface has |
| 748 |
detected the loss of signal condition from |
| 749 |
the ring." |
| 750 |
::= { dot5StatsEntry 13 } |
| 751 |
|
| 752 |
dot5StatsTransmitBeacons OBJECT-TYPE |
| 753 |
SYNTAX Counter32 |
| 754 |
MAX-ACCESS read-only |
| 755 |
STATUS current |
| 756 |
DESCRIPTION |
| 757 |
"The number of times this interface has |
| 758 |
transmitted a beacon frame." |
| 759 |
::= { dot5StatsEntry 14 } |
| 760 |
|
| 761 |
dot5StatsRecoverys OBJECT-TYPE |
| 762 |
SYNTAX Counter32 |
| 763 |
MAX-ACCESS read-only |
| 764 |
STATUS current |
| 765 |
DESCRIPTION |
| 766 |
"The number of Claim Token MAC frames |
| 767 |
received or transmitted after the interface |
| 768 |
has received a Ring Purge MAC frame. This |
| 769 |
counter signifies the number of times the |
| 770 |
ring has been purged and is being recovered |
| 771 |
back into a normal operating state." |
| 772 |
::= { dot5StatsEntry 15 } |
| 773 |
|
| 774 |
dot5StatsLobeWires OBJECT-TYPE |
| 775 |
SYNTAX Counter32 |
| 776 |
MAX-ACCESS read-only |
| 777 |
|
| 778 |
|
| 779 |
|
| 780 |
<span class="grey">McCloghrie & Decker [Page 14]</span></pre> |
| 781 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-15" ></span> |
| 782 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 783 |
|
| 784 |
|
| 785 |
STATUS current |
| 786 |
DESCRIPTION |
| 787 |
"The number of times the interface has |
| 788 |
detected an open or short circuit in the |
| 789 |
lobe data path. The adapter will be closed |
| 790 |
and dot5RingState will signify this |
| 791 |
condition." |
| 792 |
::= { dot5StatsEntry 16 } |
| 793 |
|
| 794 |
dot5StatsRemoves OBJECT-TYPE |
| 795 |
SYNTAX Counter32 |
| 796 |
MAX-ACCESS read-only |
| 797 |
STATUS current |
| 798 |
DESCRIPTION |
| 799 |
"The number of times the interface has |
| 800 |
received a Remove Ring Station MAC frame |
| 801 |
request. When this frame is received |
| 802 |
the interface will enter the close state |
| 803 |
and dot5RingState will signify this |
| 804 |
condition." |
| 805 |
::= { dot5StatsEntry 17 } |
| 806 |
|
| 807 |
dot5StatsSingles OBJECT-TYPE |
| 808 |
SYNTAX Counter32 |
| 809 |
MAX-ACCESS read-only |
| 810 |
STATUS current |
| 811 |
DESCRIPTION |
| 812 |
"The number of times the interface has |
| 813 |
sensed that it is the only station on the |
| 814 |
ring. This will happen if the interface |
| 815 |
is the first one up on a ring, or if |
| 816 |
there is a hardware problem." |
| 817 |
::= { dot5StatsEntry 18 } |
| 818 |
|
| 819 |
dot5StatsFreqErrors OBJECT-TYPE |
| 820 |
SYNTAX Counter32 |
| 821 |
MAX-ACCESS read-only |
| 822 |
STATUS current |
| 823 |
DESCRIPTION |
| 824 |
"The number of times the interface has |
| 825 |
detected that the frequency of the |
| 826 |
incoming signal differs from the expected |
| 827 |
frequency by more than that specified by |
| 828 |
the IEEE 802.5 standard." |
| 829 |
::= { dot5StatsEntry 19 } |
| 830 |
|
| 831 |
|
| 832 |
|
| 833 |
|
| 834 |
|
| 835 |
|
| 836 |
<span class="grey">McCloghrie & Decker [Page 15]</span></pre> |
| 837 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-16" ></span> |
| 838 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 839 |
|
| 840 |
|
| 841 |
-- The Timer Table |
| 842 |
|
| 843 |
-- This group contains the values of timers for 802.5 |
| 844 |
-- interfaces. This table is obsolete, but its definition |
| 845 |
-- is retained here for backwards compatibility. |
| 846 |
|
| 847 |
dot5TimerTable OBJECT-TYPE |
| 848 |
SYNTAX SEQUENCE OF Dot5TimerEntry |
| 849 |
MAX-ACCESS not-accessible |
| 850 |
STATUS obsolete |
| 851 |
DESCRIPTION |
| 852 |
"This table contains Token Ring interface |
| 853 |
timer values, one entry per 802.5 |
| 854 |
interface." |
| 855 |
::= { dot5 5 } |
| 856 |
|
| 857 |
dot5TimerEntry OBJECT-TYPE |
| 858 |
SYNTAX Dot5TimerEntry |
| 859 |
MAX-ACCESS not-accessible |
| 860 |
STATUS obsolete |
| 861 |
DESCRIPTION |
| 862 |
"A list of Token Ring timer values for an |
| 863 |
802.5 interface." |
| 864 |
INDEX { dot5TimerIfIndex } |
| 865 |
::= { dot5TimerTable 1 } |
| 866 |
|
| 867 |
Dot5TimerEntry ::= SEQUENCE { |
| 868 |
dot5TimerIfIndex Integer32, |
| 869 |
dot5TimerReturnRepeat Integer32, |
| 870 |
dot5TimerHolding Integer32, |
| 871 |
dot5TimerQueuePDU Integer32, |
| 872 |
dot5TimerValidTransmit Integer32, |
| 873 |
dot5TimerNoToken Integer32, |
| 874 |
dot5TimerActiveMon Integer32, |
| 875 |
dot5TimerStandbyMon Integer32, |
| 876 |
dot5TimerErrorReport Integer32, |
| 877 |
dot5TimerBeaconTransmit Integer32, |
| 878 |
dot5TimerBeaconReceive Integer32 |
| 879 |
} |
| 880 |
|
| 881 |
dot5TimerIfIndex OBJECT-TYPE |
| 882 |
SYNTAX Integer32 |
| 883 |
MAX-ACCESS read-only |
| 884 |
STATUS obsolete |
| 885 |
DESCRIPTION |
| 886 |
"The value of this object identifies the |
| 887 |
802.5 interface for which this entry |
| 888 |
contains timer values. The value of |
| 889 |
|
| 890 |
|
| 891 |
|
| 892 |
<span class="grey">McCloghrie & Decker [Page 16]</span></pre> |
| 893 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-17" ></span> |
| 894 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 895 |
|
| 896 |
|
| 897 |
this object for a particular interface |
| 898 |
has the same value as MIB-II's ifIndex |
| 899 |
object for the same interface." |
| 900 |
::= { dot5TimerEntry 1 } |
| 901 |
|
| 902 |
dot5TimerReturnRepeat OBJECT-TYPE |
| 903 |
SYNTAX Integer32 |
| 904 |
MAX-ACCESS read-only |
| 905 |
STATUS obsolete |
| 906 |
DESCRIPTION |
| 907 |
"The time-out value used to ensure the |
| 908 |
interface will return to Repeat State, in |
| 909 |
units of 100 micro-seconds. The value |
| 910 |
should be greater than the maximum ring |
| 911 |
latency." |
| 912 |
::= { dot5TimerEntry 2 } |
| 913 |
|
| 914 |
dot5TimerHolding OBJECT-TYPE |
| 915 |
SYNTAX Integer32 |
| 916 |
MAX-ACCESS read-only |
| 917 |
STATUS obsolete |
| 918 |
DESCRIPTION |
| 919 |
"Maximum period of time a station is |
| 920 |
permitted to transmit frames after capturing |
| 921 |
a token, in units of 100 micro-seconds." |
| 922 |
::= { dot5TimerEntry 3 } |
| 923 |
|
| 924 |
dot5TimerQueuePDU OBJECT-TYPE |
| 925 |
SYNTAX Integer32 |
| 926 |
MAX-ACCESS read-only |
| 927 |
STATUS obsolete |
| 928 |
DESCRIPTION |
| 929 |
"The time-out value for enqueuing of an SMP |
| 930 |
PDU after reception of an AMP or SMP |
| 931 |
frame in which the A and C bits were |
| 932 |
equal to 0, in units of 100 |
| 933 |
micro-seconds." |
| 934 |
::= { dot5TimerEntry 4 } |
| 935 |
|
| 936 |
dot5TimerValidTransmit OBJECT-TYPE |
| 937 |
SYNTAX Integer32 |
| 938 |
MAX-ACCESS read-only |
| 939 |
STATUS obsolete |
| 940 |
DESCRIPTION |
| 941 |
"The time-out value used by the active |
| 942 |
monitor to detect the absence of valid |
| 943 |
transmissions, in units of 100 |
| 944 |
micro-seconds." |
| 945 |
|
| 946 |
|
| 947 |
|
| 948 |
<span class="grey">McCloghrie & Decker [Page 17]</span></pre> |
| 949 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-18" ></span> |
| 950 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 951 |
|
| 952 |
|
| 953 |
::= { dot5TimerEntry 5 } |
| 954 |
|
| 955 |
dot5TimerNoToken OBJECT-TYPE |
| 956 |
SYNTAX Integer32 |
| 957 |
MAX-ACCESS read-only |
| 958 |
STATUS obsolete |
| 959 |
DESCRIPTION |
| 960 |
"The time-out value used to recover from |
| 961 |
various-related error situations. |
| 962 |
If N is the maximum number of stations on |
| 963 |
the ring, the value of this timer is |
| 964 |
normally: |
| 965 |
dot5TimerReturnRepeat + N*dot5TimerHolding." |
| 966 |
::= { dot5TimerEntry 6 } |
| 967 |
|
| 968 |
dot5TimerActiveMon OBJECT-TYPE |
| 969 |
SYNTAX Integer32 |
| 970 |
MAX-ACCESS read-only |
| 971 |
STATUS obsolete |
| 972 |
DESCRIPTION |
| 973 |
"The time-out value used by the active |
| 974 |
monitor to stimulate the enqueuing of an |
| 975 |
AMP PDU for transmission, in units of |
| 976 |
100 micro-seconds." |
| 977 |
::= { dot5TimerEntry 7 } |
| 978 |
|
| 979 |
dot5TimerStandbyMon OBJECT-TYPE |
| 980 |
SYNTAX Integer32 |
| 981 |
MAX-ACCESS read-only |
| 982 |
STATUS obsolete |
| 983 |
DESCRIPTION |
| 984 |
"The time-out value used by the stand-by |
| 985 |
monitors to ensure that there is an active |
| 986 |
monitor on the ring and to detect a |
| 987 |
continuous stream of tokens, in units of |
| 988 |
100 micro-seconds." |
| 989 |
::= { dot5TimerEntry 8 } |
| 990 |
|
| 991 |
dot5TimerErrorReport OBJECT-TYPE |
| 992 |
SYNTAX Integer32 |
| 993 |
MAX-ACCESS read-only |
| 994 |
STATUS obsolete |
| 995 |
DESCRIPTION |
| 996 |
"The time-out value which determines how |
| 997 |
often a station shall send a Report Error |
| 998 |
MAC frame to report its error counters, |
| 999 |
in units of 100 micro-seconds." |
| 1000 |
::= { dot5TimerEntry 9 } |
| 1001 |
|
| 1002 |
|
| 1003 |
|
| 1004 |
<span class="grey">McCloghrie & Decker [Page 18]</span></pre> |
| 1005 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-19" ></span> |
| 1006 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 1007 |
|
| 1008 |
|
| 1009 |
dot5TimerBeaconTransmit OBJECT-TYPE |
| 1010 |
SYNTAX Integer32 |
| 1011 |
MAX-ACCESS read-only |
| 1012 |
STATUS obsolete |
| 1013 |
DESCRIPTION |
| 1014 |
"The time-out value which determines how |
| 1015 |
long a station shall remain in the state |
| 1016 |
of transmitting Beacon frames before |
| 1017 |
entering the Bypass state, in units of |
| 1018 |
100 micro-seconds." |
| 1019 |
::= { dot5TimerEntry 10 } |
| 1020 |
|
| 1021 |
dot5TimerBeaconReceive OBJECT-TYPE |
| 1022 |
SYNTAX Integer32 |
| 1023 |
MAX-ACCESS read-only |
| 1024 |
STATUS obsolete |
| 1025 |
DESCRIPTION |
| 1026 |
"The time-out value which determines how |
| 1027 |
long a station shall receive Beacon |
| 1028 |
frames from its downstream neighbor |
| 1029 |
before entering the Bypass state, in |
| 1030 |
units of 100 micro-seconds." |
| 1031 |
::= { dot5TimerEntry 11 } |
| 1032 |
|
| 1033 |
|
| 1034 |
-- 802.5 Interface Tests |
| 1035 |
|
| 1036 |
dot5Tests OBJECT IDENTIFIER ::= { dot5 3 } |
| 1037 |
|
| 1038 |
-- <a href="./rfc1573">RFC 1573</a> defines the ifTestTable, through which a |
| 1039 |
-- network manager can instruct an agent to test an interface |
| 1040 |
-- for various faults. A test to be performed is identified |
| 1041 |
-- as an OBJECT IDENTIFIER. |
| 1042 |
|
| 1043 |
-- The Insert Function test |
| 1044 |
|
| 1045 |
dot5TestInsertFunc OBJECT-IDENTITY |
| 1046 |
STATUS current |
| 1047 |
DESCRIPTION |
| 1048 |
"Invoking this test causes the station to test the insert |
| 1049 |
ring logic of the hardware if the station's lobe media |
| 1050 |
cable is connected to a wiring concentrator. Note that |
| 1051 |
this command inserts the station into the network, and |
| 1052 |
thus, could cause problems if the station is connected |
| 1053 |
to a operational network." |
| 1054 |
::= { dot5Tests 1 } |
| 1055 |
|
| 1056 |
|
| 1057 |
|
| 1058 |
|
| 1059 |
|
| 1060 |
<span class="grey">McCloghrie & Decker [Page 19]</span></pre> |
| 1061 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-20" ></span> |
| 1062 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 1063 |
|
| 1064 |
|
| 1065 |
-- The Full-Duplex Loop Back test |
| 1066 |
|
| 1067 |
dot5TestFullDuplexLoopBack OBJECT-IDENTITY |
| 1068 |
STATUS current |
| 1069 |
DESCRIPTION |
| 1070 |
"Invoking this test on a 802.5 interface causes the |
| 1071 |
interface to check the path from memory through the |
| 1072 |
chip set's internal logic and back to memory, thus |
| 1073 |
checking the proper functioning of the system's |
| 1074 |
interface to the chip set." |
| 1075 |
::= { dot5Tests 2 } |
| 1076 |
|
| 1077 |
|
| 1078 |
-- 802.5 Hardware Chip Sets |
| 1079 |
|
| 1080 |
-- <a href="./rfc1229">RFC 1229</a> specified an object, ifExtnsChipSet, with the |
| 1081 |
-- syntax of OBJECT IDENTIFIER, to identify the hardware |
| 1082 |
-- chip set in use by an interface. <a href="./rfc1573">RFC 1573</a> obsoletes |
| 1083 |
-- the use of ifExtnsChipSet. However, the following |
| 1084 |
-- definitions are retained for backwards compatibility. |
| 1085 |
|
| 1086 |
dot5ChipSets OBJECT IDENTIFIER ::= { dot5 4 } |
| 1087 |
|
| 1088 |
dot5ChipSetIBM16 OBJECT-IDENTITY |
| 1089 |
STATUS current |
| 1090 |
DESCRIPTION |
| 1091 |
"IBM's 16/4 Mbs chip set." |
| 1092 |
::= { dot5ChipSets 1 } |
| 1093 |
|
| 1094 |
dot5ChipSetTItms380 OBJECT-IDENTITY |
| 1095 |
STATUS current |
| 1096 |
DESCRIPTION |
| 1097 |
"Texas Instruments' TMS 380 4Mbs chip-set" |
| 1098 |
::= { dot5ChipSets 2 } |
| 1099 |
|
| 1100 |
dot5ChipSetTItms380c16 OBJECT-IDENTITY |
| 1101 |
STATUS current |
| 1102 |
DESCRIPTION |
| 1103 |
"Texas Instruments' TMS 380C16 16/4 Mbs chip-set" |
| 1104 |
::= { dot5ChipSets 3 } |
| 1105 |
|
| 1106 |
|
| 1107 |
|
| 1108 |
|
| 1109 |
|
| 1110 |
|
| 1111 |
|
| 1112 |
|
| 1113 |
|
| 1114 |
|
| 1115 |
|
| 1116 |
<span class="grey">McCloghrie & Decker [Page 20]</span></pre> |
| 1117 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-21" ></span> |
| 1118 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 1119 |
|
| 1120 |
|
| 1121 |
-- conformance information |
| 1122 |
|
| 1123 |
dot5Conformance OBJECT IDENTIFIER ::= { dot5 6 } |
| 1124 |
|
| 1125 |
dot5Groups OBJECT IDENTIFIER ::= { dot5Conformance 1 } |
| 1126 |
dot5Compliances OBJECT IDENTIFIER ::= { dot5Conformance 2 } |
| 1127 |
|
| 1128 |
|
| 1129 |
-- compliance statements |
| 1130 |
|
| 1131 |
dot5Compliance MODULE-COMPLIANCE |
| 1132 |
STATUS current |
| 1133 |
DESCRIPTION |
| 1134 |
"The compliance statement for SNMPv2 entities |
| 1135 |
which implement the IEEE 802.5 MIB." |
| 1136 |
|
| 1137 |
MODULE -- this module |
| 1138 |
MANDATORY-GROUPS { dot5StateGroup, dot5StatsGroup } |
| 1139 |
|
| 1140 |
OBJECT dot5ActMonParticipate |
| 1141 |
MIN-ACCESS read-only |
| 1142 |
DESCRIPTION |
| 1143 |
"Write access is not required." |
| 1144 |
|
| 1145 |
OBJECT dot5Functional |
| 1146 |
MIN-ACCESS read-only |
| 1147 |
DESCRIPTION |
| 1148 |
"Write access is not required." |
| 1149 |
|
| 1150 |
::= { dot5Compliances 1 } |
| 1151 |
|
| 1152 |
|
| 1153 |
-- units of conformance |
| 1154 |
|
| 1155 |
dot5StateGroup OBJECT-GROUP |
| 1156 |
OBJECTS { dot5Commands, dot5RingStatus, dot5RingState, |
| 1157 |
dot5RingOpenStatus, dot5RingSpeed, dot5UpStream, |
| 1158 |
dot5ActMonParticipate, dot5Functional, |
| 1159 |
dot5LastBeaconSent |
| 1160 |
} |
| 1161 |
STATUS current |
| 1162 |
DESCRIPTION |
| 1163 |
"A collection of objects providing state information |
| 1164 |
and parameters for IEEE 802.5 interfaces." |
| 1165 |
::= { dot5Groups 1 } |
| 1166 |
|
| 1167 |
dot5StatsGroup OBJECT-GROUP |
| 1168 |
OBJECTS { dot5StatsLineErrors, dot5StatsBurstErrors, |
| 1169 |
|
| 1170 |
|
| 1171 |
|
| 1172 |
<span class="grey">McCloghrie & Decker [Page 21]</span></pre> |
| 1173 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-22" ></span> |
| 1174 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 1175 |
|
| 1176 |
|
| 1177 |
dot5StatsACErrors, dot5StatsAbortTransErrors, |
| 1178 |
dot5StatsInternalErrors, dot5StatsLostFrameErrors, |
| 1179 |
dot5StatsReceiveCongestions, |
| 1180 |
dot5StatsFrameCopiedErrors, dot5StatsTokenErrors, |
| 1181 |
dot5StatsSoftErrors, dot5StatsHardErrors, |
| 1182 |
dot5StatsSignalLoss, dot5StatsTransmitBeacons, |
| 1183 |
dot5StatsRecoverys, dot5StatsLobeWires, |
| 1184 |
dot5StatsRemoves, dot5StatsSingles, |
| 1185 |
dot5StatsFreqErrors |
| 1186 |
} |
| 1187 |
STATUS current |
| 1188 |
DESCRIPTION |
| 1189 |
"A collection of objects providing statistics for |
| 1190 |
IEEE 802.5 interfaces." |
| 1191 |
::= { dot5Groups 2 } |
| 1192 |
|
| 1193 |
END |
| 1194 |
|
| 1195 |
|
| 1196 |
|
| 1197 |
|
| 1198 |
|
| 1199 |
|
| 1200 |
|
| 1201 |
|
| 1202 |
|
| 1203 |
|
| 1204 |
|
| 1205 |
|
| 1206 |
|
| 1207 |
|
| 1208 |
|
| 1209 |
|
| 1210 |
|
| 1211 |
|
| 1212 |
|
| 1213 |
|
| 1214 |
|
| 1215 |
|
| 1216 |
|
| 1217 |
|
| 1218 |
|
| 1219 |
|
| 1220 |
|
| 1221 |
|
| 1222 |
|
| 1223 |
|
| 1224 |
|
| 1225 |
|
| 1226 |
|
| 1227 |
|
| 1228 |
<span class="grey">McCloghrie & Decker [Page 22]</span></pre> |
| 1229 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-23" ></span> |
| 1230 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 1231 |
|
| 1232 |
|
| 1233 |
<span class="h2"><a class="selflink" id="section-5" href="#section-5">5</a>. Acknowledgements</span> |
| 1234 |
|
| 1235 |
The changes from <a href="./rfc1231">RFC 1231</a> are the result of discussions on the IETF's |
| 1236 |
snmp mailing-list and in the Interfaces MIB Working Group. |
| 1237 |
|
| 1238 |
<span class="h2"><a class="selflink" id="section-6" href="#section-6">6</a>. References</span> |
| 1239 |
|
| 1240 |
[<a id="ref-1">1</a>] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure |
| 1241 |
of Management Information for version 2 of the Simple Network |
| 1242 |
Management Protocol (SNMPv2)", <a href="./rfc1442">RFC 1442</a>, SNMP Research,Inc., |
| 1243 |
Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie Mellon |
| 1244 |
University, April 1993. |
| 1245 |
|
| 1246 |
[<a id="ref-2">2</a>] McCloghrie, K., and M. Rose, Editors, "Management Information |
| 1247 |
Base for Network Management of TCP/IP-based internets: MIB-II", |
| 1248 |
STD 17, <a href="./rfc1213">RFC 1213</a>, Hughes LAN Systems, Performance Systems |
| 1249 |
International, March 1991. |
| 1250 |
|
| 1251 |
[<a id="ref-3">3</a>] Galvin, J., and K. McCloghrie, "Administrative Model for version |
| 1252 |
2 of the Simple Network Management Protocol (SNMPv2)", <a href="./rfc1445">RFC 1445</a>, |
| 1253 |
Trusted Information Systems, Hughes LAN Systems, April 1993. |
| 1254 |
|
| 1255 |
[<a id="ref-4">4</a>] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol |
| 1256 |
Operations for version 2 of the Simple Network Management |
| 1257 |
Protocol (SNMPv2)", <a href="./rfc1448">RFC 1448</a>, SNMP Research,Inc., Hughes LAN |
| 1258 |
Systems, Dover Beach Consulting, Inc., Carnegie Mellon |
| 1259 |
University, April 1993. |
| 1260 |
|
| 1261 |
[<a id="ref-5">5</a>] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual |
| 1262 |
Conventions for version 2 of the Simple Network Management |
| 1263 |
Protocol (SNMPv2)", <a href="./rfc1443">RFC 1443</a>, SNMP Research,Inc., Hughes LAN |
| 1264 |
Systems, Dover Beach Consulting, Inc., Carnegie Mellon |
| 1265 |
University, April 1993. |
| 1266 |
|
| 1267 |
[<a id="ref-6">6</a>] McCloghrie, K., and F. Kastenholz, "Evolution of the Interfaces |
| 1268 |
Group of MIB-II", <a href="./rfc1573">RFC 1573</a>, Hughes LAN Systems, FTP Software, Jan |
| 1269 |
1994 |
| 1270 |
|
| 1271 |
[<a id="ref-7">7</a>] Institute of Electrical and Electronic Engineers, "Token Ring |
| 1272 |
Access Method and Physical Layer Specifications", IEEE Standard |
| 1273 |
802.5-1989, 1989. |
| 1274 |
|
| 1275 |
|
| 1276 |
|
| 1277 |
|
| 1278 |
|
| 1279 |
|
| 1280 |
|
| 1281 |
|
| 1282 |
|
| 1283 |
|
| 1284 |
<span class="grey">McCloghrie & Decker [Page 23]</span></pre> |
| 1285 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-24" ></span> |
| 1286 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 1287 |
|
| 1288 |
|
| 1289 |
APPENDIX A - Changes from <a href="./rfc1231">RFC 1231</a> |
| 1290 |
|
| 1291 |
This memo has the following differences from <a href="./rfc1231">RFC 1231</a>: |
| 1292 |
|
| 1293 |
(1) This memo is formatted using the SNMPv2 SMI. |
| 1294 |
|
| 1295 |
(2) The relationship of the "open" and "close" states of |
| 1296 |
dot5Commands to the value of ifAdminStatus has been |
| 1297 |
clarified. In particular, the setting of one affects the |
| 1298 |
value of the other. |
| 1299 |
|
| 1300 |
(3) The relationship dot5RingSpeed and ifSpeed has been |
| 1301 |
clarified. In particular, ifSpeed indicates the current |
| 1302 |
ring-speed; dot5RingSpeed indicates the ring-speed at the |
| 1303 |
next insertion into the ring. If the interface doesn't |
| 1304 |
support changing ring-speed, then dot5RingSpeed can only be |
| 1305 |
set to its current value. When dot5RingSpeed has the value |
| 1306 |
'unknown(1)', the ring-speed is to be set to the ring's |
| 1307 |
actual ring-speed. |
| 1308 |
|
| 1309 |
(4) Write-access to dot5ActMonParticipate is not required, and a |
| 1310 |
change to the value of dot5ActMonParticipate does not take |
| 1311 |
effect until the next Active Monitor election. |
| 1312 |
|
| 1313 |
(5) Write-access to dot5Functional is not required. |
| 1314 |
|
| 1315 |
(6) A new object, dot5LastBeaconSent has been defined to contain |
| 1316 |
the timestamp of the last beacon frame sent. |
| 1317 |
|
| 1318 |
(7) The dot5TimerTable has been designated as obsolete. |
| 1319 |
|
| 1320 |
(8) Text has been added describing the applicability of <a href="./rfc1573">RFC 1573</a> |
| 1321 |
[<a href="#ref-6" title=""Evolution of the Interfaces Group of MIB-II"">6</a>] to 802.5 interfaces. |
| 1322 |
|
| 1323 |
(9) Other minor editorial changes. |
| 1324 |
|
| 1325 |
Security Considerations |
| 1326 |
|
| 1327 |
Security issues are not discussed in this memo. |
| 1328 |
|
| 1329 |
|
| 1330 |
|
| 1331 |
|
| 1332 |
|
| 1333 |
|
| 1334 |
|
| 1335 |
|
| 1336 |
|
| 1337 |
|
| 1338 |
|
| 1339 |
|
| 1340 |
<span class="grey">McCloghrie & Decker [Page 24]</span></pre> |
| 1341 |
<hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-25" ></span> |
| 1342 |
<span class="grey"><a href="./rfc1748">RFC 1748</a> IEEE 802.5 MIB using SMIv2 December 1994</span> |
| 1343 |
|
| 1344 |
|
| 1345 |
Authors' Addresses |
| 1346 |
|
| 1347 |
Keith McCloghrie |
| 1348 |
cisco Systems, Inc. |
| 1349 |
170 West Tasman Drive, |
| 1350 |
San Jose, CA 95134-1706 |
| 1351 |
|
| 1352 |
Phone: (408) 526-5260 |
| 1353 |
EMail: [email protected] |
| 1354 |
|
| 1355 |
|
| 1356 |
Eric B. Decker |
| 1357 |
cisco Systems, Inc. |
| 1358 |
1525 O'Brien Dr. |
| 1359 |
Menlo Park, CA 94025 |
| 1360 |
|
| 1361 |
Phone: (415) 688-8241 |
| 1362 |
EMail: [email protected] |
| 1363 |
|
| 1364 |
|
| 1365 |
|
| 1366 |
|
| 1367 |
|
| 1368 |
|
| 1369 |
|
| 1370 |
|
| 1371 |
|
| 1372 |
|
| 1373 |
|
| 1374 |
|
| 1375 |
|
| 1376 |
|
| 1377 |
|
| 1378 |
|
| 1379 |
|
| 1380 |
|
| 1381 |
|
| 1382 |
|
| 1383 |
|
| 1384 |
|
| 1385 |
|
| 1386 |
|
| 1387 |
|
| 1388 |
|
| 1389 |
|
| 1390 |
|
| 1391 |
|
| 1392 |
|
| 1393 |
|
| 1394 |
|
| 1395 |
|
| 1396 |
McCloghrie & Decker [Page 25] |
| 1397 |
</pre> |