Debian Codegraph @

rfc1289.html

raw
1 <pre>Network Working Group J. Saperia
2 Request for Comments: 1289 Digital Equipment Corporation
3 December 1991
4
5
6 <span class="h1">DECnet Phase IV MIB Extensions</span>
7
8 Status of this Memo
9
10 This memo is an extension to the SNMP MIB. This RFC specifies an IAB
11 standards track protocol for the Internet community, and requests
12 discussion and suggestions for improvements. Please refer to the
13 current edition of the "IAB Official Protocol Standards" for the
14 standardization state and status of this protocol. Distribution of
15 this memo is unlimited.
16
17 Table of Contents
18
19 Abstract.......................................................... <a href="#page-1">1</a>
20 <a href="#section-1">1</a>. Introduction................................................... <a href="#page-1">1</a>
21 <a href="#section-2">2</a>. Selected Objects............................................... <a href="#page-2">2</a>
22 <a href="#section-3">3</a>. Objects........................................................ <a href="#page-3">3</a>
23 <a href="#section-3.1">3.1</a> Format of Definitions......................................... <a href="#page-3">3</a>
24 <a href="#section-3.2">3.2</a> Textual Conventions........................................... <a href="#page-4">4</a>
25 <a href="#section-4">4</a>. Object Definitions............................................. <a href="#page-4">4</a>
26 <a href="#section-5">5</a>. Acknowledgements............................................... <a href="#page-63">63</a>
27 <a href="#section-6">6</a>. References..................................................... <a href="#page-63">63</a>
28 <a href="#section-7">7</a>. Security Considerations........................................ <a href="#page-64">64</a>
29 <a href="#section-8">8</a>. Author's Address............................................... <a href="#page-64">64</a>
30
31 Abstract
32
33 This memo defines a set of DECnet Phase IV extensions that have been
34 created for the Internet MIB. When used in conjunction with the
35 structure of management information (<a href="./rfc1155">RFC 1155</a>), the management
36 information base for network management of TCP/IP-based internets
37 (<a href="./rfc1213">RFC 1213</a>) and the Simple Network Management Protocol (<a href="./rfc1157">RFC 1157</a>), it
38 will be possible to provide integrated network management of combined
39 TCP/IP and DECnet Phase IV based internets. This document was
40 produced by the DECnet Phase IV MIB working group of the Internet
41 Engineering Task Force (IETF).
42
43 <span class="h2"><a class="selflink" id="section-1" href="#section-1">1</a>. Introduction</span>
44
45 With the adoption of The Simple Network Management Protocol (<a href="./rfc1157">RFC</a>
46 <a href="./rfc1157">1157</a>), the management information base for network management of
47 TCP/IP-based internets (<a href="./rfc1213">RFC 1213</a>), and the structure of management
48 information (<a href="./rfc1155">RFC 1155</a>), by the Internet, and a large number of vendor
49
50
51
52 <span class="grey">DECnet Phase IV MIB Working Group [Page 1]</span></pre>
53 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-2" ></span>
54 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
55
56
57 implementations of these standards in commercially available
58 products, it became possible to provide a higher level of effective
59 network management in TCP/IP-based internets than previously
60 available. With the growth in the use of these standards, network
61 managers desired to use this environment as a base for providing
62 integrated network management of multi-protocol networks.
63
64 DECnet Phase IV is one widely used protocol which often coexists in
65 IP-based internets. This memo provides the mechanisms by which IP-
66 based management stations can effectively manage DECnet Phase IV
67 based systems (especially router products) in an integrated fashion
68 through the use of the standard Internet SMI, MIB and Simple Network
69 Management Protocol.
70
71 DECnet Phase IV objects have been defined to be used in conjunction
72 with the Internet MIB to allow access and control of these new
73 objects by the Internet community. Additional support for other
74 DECnet-based protocols such as RBMS (remote bridge management
75 software) or other Digital Equipment Corporation Specific Hardware
76 platforms is not included in this document.
77
78 <span class="h2"><a class="selflink" id="section-2" href="#section-2">2</a>. Selected Objects</span>
79
80 The objects included in this memo have been created from the DIGITAL
81 Network Architecture Network Management Functional Specification
82 Version 4.0.0 Dated July 1983. An attempt has been made to provide a
83 reasonable ordering of these variables into groups. These groups are:
84
85 o System Group
86
87 o Network Management Group
88
89 o Session Group
90
91 o End Group
92
93 o Routing Group
94
95 o Circuit Group
96
97 o DDCMP Group
98
99 o DDCMP Multipoint Control Group
100
101 o Ethernet Group
102
103 o Counters Group
104
105
106
107
108 <span class="grey">DECnet Phase IV MIB Working Group [Page 2]</span></pre>
109 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-3" ></span>
110 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
111
112
113 o Adjacency Group
114
115 o Line Group
116
117 o Non Broadcast Line Group
118
119 o Area Group
120
121 An effort has also been made to preserve the original syntax of the
122 object wherever possible, for example, a DECnet Phase IV object is
123 Executor State. This was originally coded as a NICE (Network
124 Information and Control Exchange) data type which is a Coded single
125 field object of 1 byte in length. When converted for inclusion into
126 the Internet MIB using the Internet SMI, it became an enumerated
127 integer.
128
129 <span class="h2"><a class="selflink" id="section-3" href="#section-3">3</a>. Objects</span>
130
131 All objects in this memo are described using the standard Internet
132 SMI and BER of <a href="./rfc1155">RFC 1155</a>. A complete description of an object will
133 include the name, syntax and encoding. Just as with objects supported
134 in the MIB (<a href="./rfc1156">RFC 1156</a>), an object name is identified with an object
135 identifier which has been administratively assigned. This identifies
136 an Object Type. When an object type is combined with a specific
137 instance, the particular object is uniquely identified. The use of
138 Object Descriptors in this memo is consistent with that of <a href="./rfc1156">RFC 1156</a> -
139 they are text strings meant to be read by humans. The descriptors
140 have been taken from the original DIGITAL Network Architecture
141 Network Management Functional Specification Version 4.0.0 Dated July
142 1983 which defined DECnet Phase IV objects. These names were then
143 massaged to put them in a form as consistent as possible with object
144 type names listed in the standard Internet MIB. Object defintion
145 information is also taken directly from the Network Architecture
146 Network Managment Functional Specification cited above wherever
147 possible. In this document, EXECUTOR is intended to reference only
148 the DECnet software and is not intended to effect any other protocols
149 which may be running on the system.
150
151 <span class="h3"><a class="selflink" id="section-3.1" href="#section-3.1">3.1</a> Format of Definitions</span>
152
153 An object in this memo is specified by five fields of information:
154 Object, Syntax, Definition, Access, and Status.
155
156 The OBJECT is a textual name (OBJECT DESCRIPTOR) for that object type
157 combined with an administratively obtained OBJECT IDENTIFIER.
158
159 SYNTAX: For each object type, its abstract syntax is presented using
160 the ASN.1 specified in <a href="./rfc1155">RFC 1155</a>.
161
162
163
164 <span class="grey">DECnet Phase IV MIB Working Group [Page 3]</span></pre>
165 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-4" ></span>
166 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
167
168
169 DEFINITION: A general description of the object type. Its original
170 purpose in the DECnet Phase IV environment is given so that all
171 implementers and users will consistently interpret the information
172 contained in each object type. Changes in format to make the object
173 consistent with <a href="./rfc1155">RFC 1155</a> are also noted.
174
175 ACCESS: The standard access keywords supported in <a href="./rfc1156">RFC 1156</a> are used.
176 The keywords used in this MIB are: read-only, read-write, and, not-
177 accessible.
178
179 STATUS: The status field is used to describe with a single keyword
180 whether the object type is mandatory or optional. Status keywords of
181 obsolete and deprecated are not used in this memo since this is the
182 first version of the DECnet Phase IV MIB.
183
184 <span class="h3"><a class="selflink" id="section-3.2" href="#section-3.2">3.2</a> Textual Conventions</span>
185
186 New datatypes have been introduced as a textual conventions in this
187 DECnet Phase IV MIB document. The purpose of these additions is to
188 facilitate understanding of new objects in this MIB. No changes to
189 the SMI or the SNMP are necessary to support these conventions which
190 are described in 4.0 (Object Definitions).
191
192 <span class="h2"><a class="selflink" id="section-4" href="#section-4">4</a>. Object Definitions</span>
193
194 <a href="./rfc1289">RFC1289</a>-phivMIB
195
196 DEFINITIONS ::= BEGIN
197
198 IMPORTS
199 Gauge
200 FROM <a href="./rfc1155">RFC1155</a>-SMI
201 OBJECT-TYPE
202 FROM <a href="./rfc1212">RFC-1212</a>
203 mib-2, DisplayString
204 FROM <a href="./rfc1213">RFC1213</a>-MIB;
205
206 -- DECNet Phase-IV MIB
207
208 phiv OBJECT IDENTIFIER ::= { mib-2 18 }
209
210 -- textual conventions
211
212 PhivAddr ::= OCTET STRING (SIZE (2))
213 -- This data type is intended as a short word representation of
214 -- standard DECnet Phase IV addresses. DECnet addresses are
215 -- hierarchically structured numbers assigned to a particular
216 -- DECnet node. The address is structured so that the area
217
218
219
220 <span class="grey">DECnet Phase IV MIB Working Group [Page 4]</span></pre>
221 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-5" ></span>
222 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
223
224
225 -- number is contained in the most significant 6 bits of the
226 -- first octet. The next 2 bits of the first octet contain
227 -- the first two bits of the host address. The remainder of
228 -- the host address is contained in the second octet.
229
230 PhivCounter ::= INTEGER
231 -- This data type has been created for DECnet counters. These
232 -- counters latch at their maximum specified value until either
233 -- the system is restared, or they are reset to zero by the user
234 -- or management software.
235
236 -- groups in the decnetiv mib
237
238 phivSystem OBJECT IDENTIFIER ::= { phiv 1 }
239 phivManagement OBJECT IDENTIFIER ::= { phiv 2 }
240 session OBJECT IDENTIFIER ::= { phiv 3 }
241 end OBJECT IDENTIFIER ::= { phiv 4 }
242 routing OBJECT IDENTIFIER ::= { phiv 5 }
243 circuit OBJECT IDENTIFIER ::= { phiv 6 }
244 ddcmp OBJECT IDENTIFIER ::= { phiv 7 }
245 control OBJECT IDENTIFIER ::= { phiv 8 }
246 ethernet OBJECT IDENTIFIER ::= { phiv 9 }
247 counters OBJECT IDENTIFIER ::= { phiv 10 }
248 adjacency OBJECT IDENTIFIER ::= { phiv 11 }
249 line OBJECT IDENTIFIER ::= { phiv 12 }
250 nonBroadcastLine OBJECT IDENTIFIER ::= { phiv 14 }
251 area OBJECT IDENTIFIER ::= { phiv 15 }
252
253 -- System Group
254
255 -- The implementation of the System Group is mandatory for
256 -- all systems.
257
258 phivSystemState OBJECT-TYPE
259 SYNTAX INTEGER {
260 on (1),
261 off (2),
262 shut (3),
263 restricted (4)
264 }
265 ACCESS read-write
266 STATUS mandatory
267 DESCRIPTION
268 "This represents the operational state of the executor
269 node.
270 The possible states are:
271 ON Allows logical links.
272 OFF Allows no new links, terminates existing
273
274
275
276 <span class="grey">DECnet Phase IV MIB Working Group [Page 5]</span></pre>
277 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-6" ></span>
278 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
279
280
281 links, and stops routing traffic through.
282 SHUT Allows no new logical links, does not
283 destroy existing logical links, and goes
284 to the OFF state when all logical links are
285 gone.
286 RESTRICTED Allows no new incoming logical links from
287 other nodes.
288
289 NOTE: These values are incremented by one compared to
290 the standard DECnet values in order to maintain
291 compliance with <a href="./rfc1155">RFC 1155</a>)."
292 ::= { phivSystem 1 }
293
294 phivExecIdent OBJECT-TYPE
295 SYNTAX DisplayString ( SIZE (0..32) )
296 ACCESS read-write
297 STATUS mandatory
298 DESCRIPTION
299 "This is a text string that describes the executor node
300 (for example, 'Research Lab'). The string is up to 32
301 characters of any type."
302 ::= { phivSystem 2 }
303
304 -- Network Management Group
305
306 -- The implementation of the Network Management Group is
307 -- mandatory for all systems which contain a DECnet style
308 -- management version.
309
310
311 phivMgmtMgmtVers OBJECT-TYPE
312 SYNTAX DisplayString (SIZE (0..255) )
313 ACCESS read-only
314 STATUS mandatory
315 DESCRIPTION
316 "This is the read-only Network Management Version,
317 consisting of the version number, the Engineering
318 Change Order (ECO) number, and the user ECO number
319 (for example, 3.0.0). This parameter applies to the
320 executor node only."
321 ::= { phivManagement 1 }
322
323 -- Session Layer Group
324
325 -- The implementation of the Session Layer Group is mandatory for
326 -- all systems that implement session layer communications.
327
328
329
330
331
332 <span class="grey">DECnet Phase IV MIB Working Group [Page 6]</span></pre>
333 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-7" ></span>
334 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
335
336
337 phivSessionSystemName OBJECT-TYPE
338 SYNTAX DisplayString ( SIZE (0..6) )
339 ACCESS read-only
340 STATUS mandatory
341 DESCRIPTION
342 "Name to be associated with the node identification.
343 Only one name can be assigned to a node address or a
344 circuit identification. No name should be used more than
345 once in a DECnet network. Node-name is one to six upper
346 case alphanumeric characters with at least one alpha
347 character. A length of 0 indicates no name."
348 ::= { session 1 }
349
350 phivSessionInTimer OBJECT-TYPE
351 SYNTAX INTEGER (0..65535)
352 ACCESS read-write
353 STATUS mandatory
354 DESCRIPTION
355 "This value represents the maximum duration between the
356 time a connect is received for a process at the
357 executor node and the time that process accepts or
358 rejects it. If the connect is not accepted or rejected
359 by the user within the number of seconds specified,
360 Session Control rejects it for the user. A 0
361 indicates no timer is running."
362 ::= { session 2 }
363
364 phivSessionOutTimer OBJECT-TYPE
365 SYNTAX INTEGER (0..65535)
366 ACCESS read-write
367 STATUS mandatory
368 DESCRIPTION
369 "This value represents the duration between the time the
370 executor requests a connect and the time that connect is
371 acknowledged by the destination node. If the connect is
372 not acknowledged within the number of seconds
373 specified, Session Control returns an error. A 0
374 indicates no timer is running."
375 ::= { session 3 }
376
377 -- End Communication Layer Group
378
379 -- The implementation of the End Communication Layer Group is
380 -- mandatory for all systems that implement end layer
381 -- communications.
382
383 -- Remote State Table
384
385
386
387
388 <span class="grey">DECnet Phase IV MIB Working Group [Page 7]</span></pre>
389 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-8" ></span>
390 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
391
392
393
394 phivEndRemoteTable OBJECT-TYPE
395 SYNTAX SEQUENCE OF PhivEndRemoteEntry
396 ACCESS not-accessible
397 STATUS mandatory
398 DESCRIPTION
399 "Information about the state of sessions between the
400 node under study and the nodes found in the table."
401 ::= { end 1 }
402
403 phivEndRemoteEntry OBJECT-TYPE
404 SYNTAX PhivEndRemoteEntry
405 ACCESS not-accessible
406 STATUS mandatory
407 DESCRIPTION
408 "Information about a particular remote node as seen
409 from the end communication layer."
410 INDEX { phivEndRemoteHostNodeID }
411 ::= { phivEndRemoteTable 1 }
412
413 PhivEndRemoteEntry ::=
414 SEQUENCE {
415 phivEndRemoteHostNodeID
416 PhivAddr,
417 phivEndRemoteState
418 INTEGER,
419 phivEndCircuitIndex
420 INTEGER,
421 phivEndActiveLinks
422 INTEGER,
423 phivEndDelay
424 INTEGER (0..65535)
425 }
426 phivEndRemoteHostNodeID OBJECT-TYPE
427 SYNTAX PhivAddr -- OCTET STRING (SIZE (2))
428 ACCESS read-only
429 STATUS mandatory
430 DESCRIPTION
431 "This value is the address of the remote node to be
432 evaluated."
433 ::= { phivEndRemoteEntry 1 }
434
435 phivEndRemoteState OBJECT-TYPE
436 SYNTAX INTEGER {
437 on (1),
438 off (2),
439 shut (3),
440 restricted (4)
441
442
443
444 <span class="grey">DECnet Phase IV MIB Working Group [Page 8]</span></pre>
445 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-9" ></span>
446 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
447
448
449 }
450 ACCESS read-write
451 STATUS mandatory
452 DESCRIPTION
453 "This represents the operational state of the remote node
454 being evaluated.
455 The possible states are:
456
457 ON Allows logical links.
458 OFF Allows no new links, terminates existing
459 links, and stops routing traffic through.
460 SHUT Allows no new logical links, does not
461 destroy existing logical links, and goes
462 to the OFF state when all logical links are
463 gone.
464 RESTRICTED Allows no new incoming logical links from
465 other nodes.
466
467 NOTE: These values are incremented by one compared to
468 the standard DECnet values in order to maintain
469 compliance with <a href="./rfc1155">RFC 1155</a>."
470 ::= { phivEndRemoteEntry 2 }
471
472 phivEndCircuitIndex OBJECT-TYPE
473 SYNTAX INTEGER
474 ACCESS read-only
475 STATUS mandatory
476 DESCRIPTION
477 "A unique index value for each known circuit used to
478 communicate with the remote node. This is the same
479 value as phivCircuitIndex."
480 ::= { phivEndRemoteEntry 3 }
481
482 phivEndActiveLinks OBJECT-TYPE
483 SYNTAX INTEGER (0..65535)
484 ACCESS read-only
485 STATUS mandatory
486 DESCRIPTION
487 "This read-only parameter represents the number of active
488 logical links from the executor to the destination node."
489 ::= { phivEndRemoteEntry 4 }
490
491 phivEndDelay OBJECT-TYPE
492 SYNTAX INTEGER (0..65535)
493 ACCESS read-only
494 STATUS mandatory
495 DESCRIPTION
496 "This read-only parameter is the average round trip
497
498
499
500 <span class="grey">DECnet Phase IV MIB Working Group [Page 9]</span></pre>
501 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-10" ></span>
502 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
503
504
505 delay in seconds to the destination node. This
506 parameter is kept on a remote node basis."
507 ::= { phivEndRemoteEntry 5 }
508
509 -- End System Counter Table
510
511 phivEndCountTable OBJECT-TYPE
512 SYNTAX SEQUENCE OF PhivEndCountEntry
513 ACCESS not-accessible
514 STATUS mandatory
515 DESCRIPTION
516 "Information about the counters associated with each end
517 system that is known to the entity. These counters
518 reflect totals from the perspective of the executor
519 node."
520 ::= { end 2 }
521
522 phivEndCountEntry OBJECT-TYPE
523 SYNTAX PhivEndCountEntry
524 ACCESS not-accessible
525 STATUS mandatory
526 DESCRIPTION
527 "Information about a particular session between two end
528 systems."
529 INDEX { phivEndCountHostNodeID }
530 ::= { phivEndCountTable 1 }
531
532 PhivEndCountEntry ::=
533 SEQUENCE {
534 phivEndCountHostNodeID
535 PhivAddr,
536 phivEndCountSecsLastZeroed
537 PhivCounter (0..65535),
538 phivEndCountUsrBytesRec
539 PhivCounter,
540 phivEndCountUsrBytesSent
541 PhivCounter,
542 phivEndUCountUsrMessRec
543 PhivCounter,
544 phivEndCountUsrMessSent
545 PhivCounter,
546 phivEndCountTotalBytesRec
547 PhivCounter,
548 phivEndCountTotalBytesSent
549 PhivCounter,
550 phivEndCountTotalMessRec
551 PhivCounter,
552 phivEndCountTotalMessSent
553
554
555
556 <span class="grey">DECnet Phase IV MIB Working Group [Page 10]</span></pre>
557 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-11" ></span>
558 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
559
560
561 PhivCounter,
562 phivEndCountConnectsRecd
563 PhivCounter (0..65535),
564 phivEndCountConnectsSent
565 PhivCounter (0..65535),
566 phivEndCountReponseTimeouts
567 PhivCounter (0..65535),
568 phivEndCountRecdConnectResErrs
569 PhivCounter (0..65535)
570 }
571 phivEndCountHostNodeID OBJECT-TYPE
572 SYNTAX PhivAddr -- OCTET STRING (SIZE (2))
573 ACCESS read-only
574 STATUS mandatory
575 DESCRIPTION
576 "This value is the address of the remote node to be
577 evaluated."
578 ::= { phivEndCountEntry 1 }
579
580 phivEndCountSecsLastZeroed OBJECT-TYPE
581 SYNTAX PhivCounter (0..65535)
582 ACCESS read-only
583 STATUS mandatory
584 DESCRIPTION
585 "This value is the number of seconds that have elapsed
586 since the counters for the node in this table row were
587 last set to zero. This counter is located in the
588 network management layer, but is returned with the
589 end system information which follows."
590 ::= { phivEndCountEntry 2 }
591
592 phivEndCountUsrBytesRec OBJECT-TYPE
593 SYNTAX PhivCounter
594 ACCESS read-only
595 STATUS mandatory
596 DESCRIPTION
597 "Number of user bytes received from the target host."
598 ::= { phivEndCountEntry 3 }
599
600 phivEndCountUsrBytesSent OBJECT-TYPE
601 SYNTAX PhivCounter
602 ACCESS read-only
603 STATUS mandatory
604 DESCRIPTION
605 "Number of user bytes sent to the target host."
606 ::= { phivEndCountEntry 4 }
607
608
609
610
611
612 <span class="grey">DECnet Phase IV MIB Working Group [Page 11]</span></pre>
613 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-12" ></span>
614 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
615
616
617 phivEndUCountUsrMessRec OBJECT-TYPE
618 SYNTAX PhivCounter
619 ACCESS read-only
620 STATUS mandatory
621 DESCRIPTION
622 "Number of user messages received from the target host."
623 ::= { phivEndCountEntry 5 }
624
625 phivEndCountUsrMessSent OBJECT-TYPE
626 SYNTAX PhivCounter
627 ACCESS read-only
628 STATUS mandatory
629 DESCRIPTION
630 "Number of user messages sent to the target host."
631 ::= { phivEndCountEntry 6 }
632
633 phivEndCountTotalBytesRec OBJECT-TYPE
634 SYNTAX PhivCounter
635 ACCESS read-only
636 STATUS mandatory
637 DESCRIPTION
638 "Number of bytes received from the target host."
639 ::= { phivEndCountEntry 7 }
640
641 phivEndCountTotalBytesSent OBJECT-TYPE
642 SYNTAX PhivCounter
643 ACCESS read-only
644 STATUS mandatory
645 DESCRIPTION
646 "Number of bytes sent to the target host."
647 ::= { phivEndCountEntry 8 }
648
649 phivEndCountTotalMessRec OBJECT-TYPE
650 SYNTAX PhivCounter
651 ACCESS read-only
652 STATUS mandatory
653 DESCRIPTION
654 "Number of messages received from the target host."
655 ::= { phivEndCountEntry 9 }
656
657 phivEndCountTotalMessSent OBJECT-TYPE
658 SYNTAX PhivCounter
659 ACCESS read-only
660 STATUS mandatory
661 DESCRIPTION
662 "Number of messages sent to the target host."
663 ::= { phivEndCountEntry 10 }
664
665
666
667
668 <span class="grey">DECnet Phase IV MIB Working Group [Page 12]</span></pre>
669 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-13" ></span>
670 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
671
672
673 phivEndCountConnectsRecd OBJECT-TYPE
674 SYNTAX PhivCounter (0..65535)
675 ACCESS read-only
676 STATUS mandatory
677 DESCRIPTION
678 "Number of connects received from the target host."
679 ::= { phivEndCountEntry 11 }
680
681 phivEndCountConnectsSent OBJECT-TYPE
682 SYNTAX PhivCounter (0..65535)
683 ACCESS read-only
684 STATUS mandatory
685 DESCRIPTION
686 "Number of connects sent to the target host."
687 ::= {phivEndCountEntry 12 }
688
689 phivEndCountReponseTimeouts OBJECT-TYPE
690 SYNTAX PhivCounter (0..65535)
691 ACCESS read-only
692 STATUS mandatory
693 DESCRIPTION
694 "Number of response timeouts."
695 ::= { phivEndCountEntry 13 }
696
697 phivEndCountRecdConnectResErrs OBJECT-TYPE
698 SYNTAX PhivCounter (0..65535)
699 ACCESS read-only
700 STATUS mandatory
701 DESCRIPTION
702 "Number of received connect resource errors."
703 ::= {phivEndCountEntry 14 }
704
705
706 -- additional End System objects
707
708 phivEndMaxLinks OBJECT-TYPE
709 SYNTAX INTEGER (1..65535)
710 ACCESS read-write
711 STATUS mandatory
712 DESCRIPTION
713 "This value represents the maximum active logical
714 link count allowed for the executor."
715 ::= { end 3 }
716
717 phivEndNSPVers OBJECT-TYPE
718 SYNTAX DisplayString (SIZE (0..255) )
719 ACCESS read-only
720 STATUS mandatory
721
722
723
724 <span class="grey">DECnet Phase IV MIB Working Group [Page 13]</span></pre>
725 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-14" ></span>
726 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
727
728
729 DESCRIPTION
730 "This read-only parameter represents the version number
731 of the node End Communication S/W. The format is
732 version number, ECO, and user ECO, e.g., 4.1.0"
733 ::= { end 4 }
734
735 phivEndRetransmitFactor OBJECT-TYPE
736 SYNTAX INTEGER (1..65535)
737 ACCESS read-write
738 STATUS mandatory
739 DESCRIPTION
740 "This value represents the maximum number of times the
741 source End Communication at the executor node will
742 restart the retransmission timer when it expires. If
743 the number is exceeded, Session Control disconnects the
744 logical link for the user."
745 ::= { end 5 }
746
747 phivEndDelayFact OBJECT-TYPE
748 SYNTAX INTEGER (1..255)
749 ACCESS read-write
750 STATUS mandatory
751 DESCRIPTION
752 "This is the number by which to multiply one sixteenth
753 of the estimated round trip delay to a node to set the
754 retransmission timer to that node."
755 ::= { end 6 }
756
757 phivEndDelayWeight OBJECT-TYPE
758 SYNTAX INTEGER (1..255)
759 ACCESS read-write
760 STATUS mandatory
761 DESCRIPTION
762 "This number represents the weight to apply to a
763 current round trip delay estimate to a remote node
764 when updating the estimated round trip delay to a node.
765 On some systems the number must be 1 less than a power
766 of 2 for computational efficiency."
767 ::= { end 7 }
768
769 phivEndInactivityTimer OBJECT-TYPE
770 SYNTAX INTEGER (1..65535)
771 ACCESS read-write
772 STATUS mandatory
773 DESCRIPTION
774 "This value represents the maximum duration of inactivity
775 (no data in either direction) on a logical link before
776 the node checks to see if the logical link still works.
777
778
779
780 <span class="grey">DECnet Phase IV MIB Working Group [Page 14]</span></pre>
781 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-15" ></span>
782 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
783
784
785 If no activity occurs within the minimum number of
786 seconds, End Communication generates artificial
787 traffic to test the link (End Communication
788 specification)."
789 ::= { end 8 }
790
791 phivEndCountZeroCount OBJECT-TYPE
792 SYNTAX INTEGER {
793 other (1),
794 reset (2)
795 }
796 ACCESS read-write
797 STATUS mandatory
798 DESCRIPTION
799 "When this value is set to 2, all of the counters in
800 the End System Counter Table are set to zero."
801 ::= { end 9 }
802
803 phivEndMaxLinksActive OBJECT-TYPE
804 SYNTAX PhivCounter (0..65535)
805 ACCESS read-write
806 STATUS mandatory
807 DESCRIPTION
808 "This value represents the high water mark for the
809 number of links that were active at any one time."
810 ::= { end 10 }
811
812 -- Routing Layer Group
813
814 -- The implementation of the Routing Layer Group is mandatory for
815 -- all systems that implement level 1 routing layer
816 -- communications.
817
818 phivRouteBroadcastRouteTimer OBJECT-TYPE
819 SYNTAX INTEGER (1..65535)
820 ACCESS read-write
821 STATUS mandatory
822 DESCRIPTION
823 "This value determines the maximum time in seconds
824 allowed between Routing updates on Ethernet
825 circuits. When this timer expired before a routing
826 update occurs, a routing update is forced. With a
827 standard calculation, Routing also uses this timer
828 to enforce a minimum delay between routing updates."
829 ::= { routing 1 }
830
831 phivRouteBuffSize OBJECT-TYPE
832 SYNTAX INTEGER (1..65535)
833
834
835
836 <span class="grey">DECnet Phase IV MIB Working Group [Page 15]</span></pre>
837 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-16" ></span>
838 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
839
840
841 ACCESS read-write
842 STATUS mandatory
843 DESCRIPTION
844 "This parameter value determines the maximum size of
845 a Routing message. It therefore determines the maximum
846 size message that can be forwarded. This size includes
847 protocol overhead down to and including the End
848 Communication layer, plus a constant value of 6. (This
849 value of 6 is included to provide compatibility with
850 the parameter definition in Phase III, which included
851 the Routing overhead.) It does not include Routing or
852 Data link overhead (except for the constant value of
853 6). There is one buffer size for all circuits.
854
855 NOTE: The BUFFER SIZE defines the maximum size messages
856 that the Routing layer can forward. The SEGMENT BUFFER
857 SIZE (defined below) defines the maximum size messages
858 that the End Communication layer can transmit or
859 receive. The SEGMENT BUFFER SIZE is always less than
860 or equal to the BUFFER SIZE. Normally the two
861 parameters will be equal. They may be different to
862 allow the network manager to alter buffer sizes
863 on all nodes without interruption of service. They both
864 include an extra 6 bytes for compatibility with Phase
865 III."
866 ::= { routing 2 }
867
868 phivRouteRoutingVers OBJECT-TYPE
869 SYNTAX DisplayString ( SIZE (0..255) )
870 ACCESS read-only
871 STATUS mandatory
872 DESCRIPTION
873 "This read-only parameter identifies the executor node's
874 Routing version number. The format is version number,
875 ECO, and user ECO, e.g., 4.1.0"
876 ::= { routing 3 }
877
878 phivRouteMaxAddr OBJECT-TYPE
879 SYNTAX INTEGER (1..1023)
880 ACCESS read-write
881 STATUS mandatory
882 DESCRIPTION
883 "This value represents the largest node number and,
884 therefore, number of nodes that can be known about
885 by the executor node's home area."
886 ::= { routing 4 }
887
888
889
890
891
892 <span class="grey">DECnet Phase IV MIB Working Group [Page 16]</span></pre>
893 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-17" ></span>
894 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
895
896
897 phivRouteMaxBdcastNonRouters OBJECT-TYPE
898 SYNTAX INTEGER (0..65535)
899 ACCESS read-write
900 STATUS mandatory
901 DESCRIPTION
902 "This value represents the maximum total number of
903 nonrouters the executor node can have on its Ethernet
904 circuits."
905 ::= { routing 5 }
906
907 phivRouteMaxBdcastRouters OBJECT-TYPE
908 SYNTAX INTEGER (0..65535)
909 ACCESS read-write
910 STATUS mandatory
911 DESCRIPTION
912 "This value represents the maximum total number of
913 routers the executor node can have on its Ethernet
914 circuits."
915 ::= { routing 6 }
916
917 phivRouteMaxBuffs OBJECT-TYPE
918 SYNTAX INTEGER (1..65535)
919 ACCESS read-write
920 STATUS mandatory
921 DESCRIPTION
922 "This value represents the maximum number of transmit
923 buffers that Routing may use for all circuits."
924 ::= { routing 7 }
925
926 phivRouteMaxCircuits OBJECT-TYPE
927 SYNTAX INTEGER (1..65535)
928 ACCESS read-write
929 STATUS mandatory
930 DESCRIPTION
931 "This value represents the maximum number of Routing
932 circuits that the executor node can know about."
933 ::= { routing 8 }
934
935 phivRouteMaxCost OBJECT-TYPE
936 SYNTAX INTEGER (1..1022)
937 ACCESS read-write
938 STATUS mandatory
939 DESCRIPTION
940 "This value represents the maximum total path cost
941 allowed from the executor to any node within an area.
942 The path cost is the sum of the circuit costs along
943 a path between two nodes. This parameter defines the
944 point where the executor node's Routing routing
945
946
947
948 <span class="grey">DECnet Phase IV MIB Working Group [Page 17]</span></pre>
949 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-18" ></span>
950 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
951
952
953 decision algorithm declares another node unreachable
954 because the cost of the least costly path to the
955 other node is excessive. For correct operation, this
956 parameter must not be less than the maximum path cost
957 of the network."
958 ::= { routing 9 }
959
960 phivRouteMaxHops OBJECT-TYPE
961 SYNTAX INTEGER (1..30)
962 ACCESS read-write
963 STATUS mandatory
964 DESCRIPTION
965 "This value represents the maximum number of routing hops
966 allowable from the executor to any other reachable node
967 within an area. (A hop is the logical distance over a
968 circuit between two adjacent nodes.) This parameter
969 defines the point where the executor node's Routing
970 routing decision algorithm declares another node
971 unreachable because the length of the shortest path
972 between the two nodes is too long. For correct
973 operation, this parameter must not be less than the
974 network diameter. (The network diameter is the
975 reachability distance between the two nodes of the
976 network having the greatest reachability distance,
977 where reachability distance is the length the shortest
978 path between a given pair of nodes.)"
979 ::= { routing 10 }
980
981 phivRouteMaxVisits OBJECT-TYPE
982 SYNTAX INTEGER (1..63)
983 ACCESS read-write
984 STATUS mandatory
985 DESCRIPTION
986 "This value represents the maximum number of nodes a
987 message coming into the executor node can have visited.
988 If the message is not for this node and the MAXIMUM
989 VISITS number is exceeded, the message is discarded.
990 The MAXIMUM VISITS parameter defines the point where
991 the packet lifetime control algorithm discards
992 a packet that has traversed too many nodes. For correct
993 operation, this parameter must not be less than the
994 maximum path length of the network. (The maximum path
995 length is the routing distance between the two nodes of
996 the network having the greatest routing distance, where
997 routing distance is the length of the least costly
998 path between a given pair of nodes.)"
999 ::= { routing 11 }
1000
1001
1002
1003
1004 <span class="grey">DECnet Phase IV MIB Working Group [Page 18]</span></pre>
1005 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-19" ></span>
1006 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1007
1008
1009 phivRouteRoutingTimer OBJECT-TYPE
1010 SYNTAX INTEGER (1..65535)
1011 ACCESS read-write
1012 STATUS mandatory
1013 DESCRIPTION
1014 "This value determines the maximum time in seconds
1015 allowed between Routing updates on non-Ethernet
1016 circuits. When this timer expires before a routing
1017 update occurs, a routing update is forced."
1018 ::= { routing 12 }
1019
1020 phivRouteSegBuffSize OBJECT-TYPE
1021 SYNTAX INTEGER
1022 ACCESS read-write
1023 STATUS mandatory
1024 DESCRIPTION
1025 "This parameter value determines the maximum size of an
1026 end-to-end segment. The size is a decimal integer in
1027 the range 1-65535. This size is in bytes. This size
1028 includes protocol overhead down to and including the
1029 End Communication layer, plus a constant value of 6.
1030 (This value of 6 is included to provide compatibility
1031 with the BUFFER SIZE parameter definition.) It does not
1032 include Routing or Data link overhead (except for the
1033 constant value of 6)."
1034 ::= { routing 13 }
1035
1036 phivRouteType OBJECT-TYPE
1037 SYNTAXINTEGER {
1038 routing-III (1),
1039 nonrouting-III (2),
1040 area (3),
1041 routing-IV (4),
1042 nonrouting-IV (5)
1043 }
1044 ACCESS read-only
1045 STATUS mandatory
1046 DESCRIPTION
1047 "This parameter indicates the type of the executor
1048 node. The node-type is one of the following:
1049
1050 routing-III
1051 nonrouting-III
1052 routing-IV
1053 ronrouting-IV
1054 area
1055
1056 A routing node has full routing capability. A
1057
1058
1059
1060 <span class="grey">DECnet Phase IV MIB Working Group [Page 19]</span></pre>
1061 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-20" ></span>
1062 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1063
1064
1065 nonrouting node contains a subset of the Routing
1066 routing modules. The III and IV indicate the DNA
1067 phase of the node. Nonrouting nodes can deliver
1068 and receive packets to and from any node, but cannot
1069 route packets from other nodes through to other nodes.
1070 An area node routes between areas. Refer to the Routing
1071 specification for details.
1072
1073 For adjacent nodes, this is a read-only parameter that
1074 indicates the type of the reachable adjacent node.
1075 NOTE: The ROUTING-III and NONROUTING-III values are
1076 incremented by one compared to the standard DECnet
1077 values in order to maintain compliance with <a href="./rfc1155">RFC 1155</a>)"
1078 ::= { routing 14 }
1079
1080 phivRouteCountAgedPktLoss OBJECT-TYPE
1081 SYNTAX PhivCounter (0..127)
1082 ACCESS read-only
1083 STATUS mandatory
1084 DESCRIPTION
1085 "Number of aged packet losses."
1086 ::= { routing 15 }
1087
1088 phivRouteCountNodeUnrPktLoss OBJECT-TYPE
1089 SYNTAX PhivCounter (0..65535)
1090 ACCESS read-only
1091 STATUS mandatory
1092 DESCRIPTION
1093 "Number of node unreachable packet losses."
1094 ::= { routing 16 }
1095
1096 phivRouteCountOutRngePktLoss OBJECT-TYPE
1097 SYNTAX PhivCounter (0..127)
1098 ACCESS read-only
1099 STATUS mandatory
1100 DESCRIPTION
1101 "Number of node out-of-range packet losses."
1102 ::= { routing 17 }
1103
1104 phivRouteCountOverSzePktLoss OBJECT-TYPE
1105 SYNTAX PhivCounter (0..127)
1106 ACCESS read-only
1107 STATUS mandatory
1108 DESCRIPTION
1109 "Number of Oversized packet losses."
1110 ::= { routing 18 }
1111
1112
1113
1114
1115
1116 <span class="grey">DECnet Phase IV MIB Working Group [Page 20]</span></pre>
1117 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-21" ></span>
1118 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1119
1120
1121 phivRouteCountPacketFmtErr OBJECT-TYPE
1122 SYNTAX PhivCounter (0..127)
1123 ACCESS read-only
1124 STATUS mandatory
1125 DESCRIPTION
1126 "Number of packet format errors."
1127 ::= { routing 19 }
1128
1129 phivRouteCountPtlRteUpdtLoss OBJECT-TYPE
1130 SYNTAX PhivCounter (0..127)
1131 ACCESS read-only
1132 STATUS mandatory
1133 DESCRIPTION
1134 "Number of partial routing update losses."
1135 ::= { routing 20 }
1136
1137 phivRouteCountVerifReject OBJECT-TYPE
1138 SYNTAX PhivCounter (0..127)
1139 ACCESS read-only
1140 STATUS mandatory
1141 DESCRIPTION
1142 "Number of verification rejects."
1143 ::= { routing 21 }
1144
1145 -- Level 1 Routing Table
1146
1147 phivLevel1RouteTable OBJECT-TYPE
1148 SYNTAX SEQUENCE OF PhivLevel1RouteEntry
1149 ACCESS not-accessible
1150 STATUS mandatory
1151 DESCRIPTION
1152 "Information about the currently known DECnet Phase
1153 IV Routes."
1154 ::= { routing 22 }
1155
1156 phivLevel1RouteEntry OBJECT-TYPE
1157 SYNTAX PhivLevel1RouteEntry
1158 ACCESS not-accessible
1159 STATUS mandatory
1160 DESCRIPTION
1161 "Information about the currently known DECnet Phase
1162 IV Routes."
1163 INDEX { phivLevel1RouteNodeAddr }
1164 ::= { phivLevel1RouteTable 1 }
1165
1166 PhivLevel1RouteEntry ::=
1167 SEQUENCE {
1168 phivLevel1RouteNodeAddr
1169
1170
1171
1172 <span class="grey">DECnet Phase IV MIB Working Group [Page 21]</span></pre>
1173 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-22" ></span>
1174 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1175
1176
1177 PhivAddr,
1178 phivLevel1RouteCircuitIndex
1179 INTEGER,
1180 phivLevel1RouteCost
1181 INTEGER (0..65535),
1182 phivLevel1RouteHops
1183 INTEGER (0..127),
1184 phivLevel1RouteNextNode
1185 PhivAddr
1186 }
1187 phivLevel1RouteNodeAddr OBJECT-TYPE
1188 SYNTAX PhivAddr -- OCTET STRING (SIZE (2))
1189 ACCESS read-only
1190 STATUS mandatory
1191 DESCRIPTION
1192 "This value is the address of the node about which
1193 routing information is contained in this level 1
1194 routing table."
1195 ::= { phivLevel1RouteEntry 1 }
1196
1197 phivLevel1RouteCircuitIndex OBJECT-TYPE
1198 SYNTAX INTEGER
1199 ACCESS read-only
1200 STATUS mandatory
1201 DESCRIPTION
1202 "A unique index value for each known circuit. This is
1203 the index to the circuit state table and is the same
1204 value as phivCircuitIndex."
1205 ::= { phivLevel1RouteEntry 2 }
1206
1207 phivLevel1RouteCost OBJECT-TYPE
1208 SYNTAX INTEGER (0..65535)
1209 ACCESS read-only
1210 STATUS mandatory
1211 DESCRIPTION
1212 "This read-only parameter represents the total cost
1213 over the current path to the destination node. Cost is
1214 a positive integer value associated with using a
1215 circuit. Routing routes messages (data) along the path
1216 between two nodes with the smallest cost. COST is kept
1217 on a remote node basis."
1218 ::= { phivLevel1RouteEntry 3 }
1219
1220 phivLevel1RouteHops OBJECT-TYPE
1221 SYNTAX INTEGER (0..127)
1222 ACCESS read-only
1223 STATUS mandatory
1224 DESCRIPTION
1225
1226
1227
1228 <span class="grey">DECnet Phase IV MIB Working Group [Page 22]</span></pre>
1229 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-23" ></span>
1230 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1231
1232
1233 "This read-only parameter represents the number of hops
1234 over to a destination node. A hop is Routing value
1235 representing the logical distance between two nodes in
1236 a network. HOPS is kept on a remote node basis."
1237 ::= { phivLevel1RouteEntry 4 }
1238
1239 phivLevel1RouteNextNode OBJECT-TYPE
1240 SYNTAX PhivAddr -- OCTET STRING (SIZE (2))
1241 ACCESS read-only
1242 STATUS mandatory
1243 DESCRIPTION
1244 "This read-only value indicates the next node on the
1245 circuit used to get to the node under scrutiny
1246 (next hop)."
1247 ::= { phivLevel1RouteEntry 5 }
1248
1249 -- Additional routing parameters
1250
1251 phivRouteCountZeroCount OBJECT-TYPE
1252 SYNTAX INTEGER {
1253 other (1),
1254 reset (2)
1255 }
1256 ACCESS read-write
1257 STATUS mandatory
1258 DESCRIPTION
1259 "When this value is set to 2, the following objects are
1260 set to Zero: phivRouteCountAgedPktLoss,
1261 phivRouteCountNodeUnrPktLoss,
1262 phivRouteCountOutRngePktLoss,
1263 phivRouteCountOverSzePktLoss,
1264 phivRouteCountPacketFmtErr,
1265 phivRouteCountPtlRteUpdtLoss, and
1266 phivRouteCountVerifReject."
1267 ::= { routing 23 }
1268
1269 phivRouteSystemAddr OBJECT-TYPE
1270 SYNTAX PhivAddr
1271 ACCESS read-only
1272 STATUS mandatory
1273 DESCRIPTION
1274 "DECnet Phase IV node address."
1275 ::= { routing 24 }
1276
1277
1278
1279
1280
1281
1282
1283
1284 <span class="grey">DECnet Phase IV MIB Working Group [Page 23]</span></pre>
1285 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-24" ></span>
1286 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1287
1288
1289 -- Circuit Group
1290
1291 -- The implementation of the Circuit Group is mandatory for
1292 -- all systems.
1293
1294 -- Circuit Parameters Table
1295
1296
1297 phivCircuitParametersTable OBJECT-TYPE
1298 SYNTAX SEQUENCE OF PhivCircuitParametersEntry
1299 ACCESS not-accessible
1300 STATUS mandatory
1301 DESCRIPTION
1302 "Information about the parameters associated with all
1303 circuits currently known."
1304 ::= {circuit 1 }
1305
1306 phivCircuitParametersEntry OBJECT-TYPE
1307 SYNTAX PhivCircuitParametersEntry
1308 ACCESS not-accessible
1309 STATUS mandatory
1310 DESCRIPTION
1311 "Parameters information about all circuits currently
1312 known."
1313 INDEX { phivCircuitIndex }
1314 ::= { phivCircuitParametersTable 1 }
1315
1316 PhivCircuitParametersEntry ::=
1317 SEQUENCE {
1318 phivCircuitIndex
1319 INTEGER,
1320 phivCircuitLineIndex
1321 INTEGER,
1322 phivCircuitCommonState
1323 INTEGER,
1324 phivCircuitCommonSubState
1325 INTEGER,
1326 phivCircuitCommonName
1327 DisplayString,
1328 phivCircuitExecRecallTimer
1329 INTEGER (0..65535),
1330 phivCircuitCommonType
1331 INTEGER,
1332 phivCircuitService
1333 INTEGER,
1334 phivCircuitExecCost
1335 INTEGER (1..25),
1336 phivCircuitExecHelloTimer
1337
1338
1339
1340 <span class="grey">DECnet Phase IV MIB Working Group [Page 24]</span></pre>
1341 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-25" ></span>
1342 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1343
1344
1345 INTEGER (1..8191)
1346 }
1347 phivCircuitIndex OBJECT-TYPE
1348 SYNTAX INTEGER
1349 ACCESS read-only
1350 STATUS mandatory
1351 DESCRIPTION
1352 "A unique index value for each known circuit."
1353 ::= { phivCircuitParametersEntry 1 }
1354
1355 phivCircuitLineIndex OBJECT-TYPE
1356 SYNTAX INTEGER
1357 ACCESS read-only
1358 STATUS mandatory
1359 DESCRIPTION
1360 "The line on which this circuit is active. This is
1361 the same as the IfIndex."
1362 ::= { phivCircuitParametersEntry 2 }
1363
1364 phivCircuitCommonState OBJECT-TYPE
1365 SYNTAX INTEGER {
1366 on (1),
1367 off (2),
1368 service (3),
1369 cleared (4)
1370 }
1371 ACCESS read-write
1372 STATUS mandatory
1373 DESCRIPTION
1374 "This value represents the circuit's Network Management
1375 operational state. NOTE: These values are incremented
1376 by one compared to the standard DECnet values in order
1377 to maintain compliance with <a href="./rfc1155">RFC 1155</a>."
1378 ::= { phivCircuitParametersEntry 3 }
1379
1380 phivCircuitCommonSubState OBJECT-TYPE
1381 SYNTAX INTEGER {
1382 starting (1),
1383 reflecting (2),
1384 looping (3),
1385 loading (4),
1386 dumping (5),
1387 triggering (6),
1388 autoservice (7),
1389 autoloading (8),
1390 autodumping (9),
1391 autotriggering (10),
1392 synchronizing (11),
1393
1394
1395
1396 <span class="grey">DECnet Phase IV MIB Working Group [Page 25]</span></pre>
1397 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-26" ></span>
1398 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1399
1400
1401 failed (12),
1402 running (13)
1403 }
1404 ACCESS read-only
1405 STATUS mandatory
1406 DESCRIPTION
1407 "This value represents the circuit's Network Management
1408 operational and service substate. NOTE: These values are
1409 incremented by one compared to the standard DECnet values
1410 in order to maintain compliance with <a href="./rfc1155">RFC 1155</a>."
1411 ::= { phivCircuitParametersEntry 4 }
1412
1413 phivCircuitCommonName OBJECT-TYPE
1414 SYNTAX DisplayString ( SIZE (0..16) )
1415 ACCESS read-only
1416 STATUS mandatory
1417 DESCRIPTION
1418 "The name of the circuit entry in the table, for example,
1419 SVA-0 or in a level 2 router ASYNC-8 or ETHER-1)."
1420 ::= { phivCircuitParametersEntry 5 }
1421
1422 phivCircuitExecRecallTimer OBJECT-TYPE
1423 SYNTAX INTEGER (0..65535)
1424 ACCESS read-write
1425 STATUS mandatory
1426 DESCRIPTION
1427 "This parameter represents the minimum number of
1428 seconds to wait before restarting the circuit. A
1429 value of 0 indicates not timer is running."
1430 ::= { phivCircuitParametersEntry 6 }
1431
1432 phivCircuitCommonType OBJECT-TYPE
1433 SYNTAX INTEGER {
1434 ddcmp-point (1),
1435 ddcmp-control (2),
1436 ddcmp-tributary (3),
1437 x25 (4),
1438 ddcmp-dmc (5),
1439 ethernet (6),
1440 ci (7),
1441 qp2-dte20 (8),
1442 bisync (9),
1443 other (14),
1444 fddi (15)
1445 }
1446 ACCESS read-only
1447 STATUS mandatory
1448 DESCRIPTION
1449
1450
1451
1452 <span class="grey">DECnet Phase IV MIB Working Group [Page 26]</span></pre>
1453 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-27" ></span>
1454 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1455
1456
1457 "Represents the type of the circuit. For X.25 circuits,
1458 the value must be set to X25. For DDCMP and Ethernet
1459 circuits it is read only and is the same value as the
1460 protocol of the associated line.
1461 NOTE: Values 1 - 5 are incremented by one compared to the
1462 standard DECnet values in order to maintain compliance
1463 with <a href="./rfc1155">RFC 1155</a>."
1464 ::= { phivCircuitParametersEntry 7 }
1465
1466 phivCircuitService OBJECT-TYPE
1467 SYNTAX INTEGER {
1468 enabled (1),
1469 disabled (2)
1470 }
1471 ACCESS read-write
1472 STATUS mandatory
1473 DESCRIPTION
1474 "This value indicates whether or not Network Management
1475 allows service operations on a circuit. The values for
1476 service-control are as follows:
1477
1478 ENABLED SERVICE state and/or service functions are
1479 allowed.
1480
1481 DISABLED SERVICE state and/or service functions are not
1482 allowed.
1483
1484 NOTE: These values are incremented by one compared to the
1485 standard DECnet values in order to maintain compliance
1486 with <a href="./rfc1155">RFC 1155</a>."
1487 ::= { phivCircuitParametersEntry 8 }
1488
1489 phivCircuitExecCost OBJECT-TYPE
1490 SYNTAX INTEGER (1..25)
1491 ACCESS read-write
1492 STATUS mandatory
1493 DESCRIPTION
1494 "This value represents the routing cost of the circuit.
1495 Routing sends messages along the path between two nodes
1496 having the smallest cost."
1497 ::= { phivCircuitParametersEntry 9 }
1498
1499 phivCircuitExecHelloTimer OBJECT-TYPE
1500 SYNTAX INTEGER (1..8191)
1501 ACCESS read-write
1502 STATUS mandatory
1503 DESCRIPTION
1504 "This value determines the frequency of Routing Hello
1505
1506
1507
1508 <span class="grey">DECnet Phase IV MIB Working Group [Page 27]</span></pre>
1509 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-28" ></span>
1510 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1511
1512
1513 messages sent to the adjacent node on the circuit."
1514 ::= { phivCircuitParametersEntry 10 }
1515
1516 -- Circuit Counters Table
1517
1518
1519 phivCircuitCountTable OBJECT-TYPE
1520 SYNTAX SEQUENCE OF PhivCircuitCountEntry
1521 ACCESS not-accessible
1522 STATUS mandatory
1523 DESCRIPTION
1524 "Information about the counters associated with all
1525 circuits currently known."
1526 ::= { circuit 2 }
1527
1528 phivCircuitCountEntry OBJECT-TYPE
1529 SYNTAX PhivCircuitCountEntry
1530 ACCESS not-accessible
1531 STATUS mandatory
1532 DESCRIPTION
1533 "Counter information about all circuits currently known"
1534 INDEX { phivCircuitIndex }
1535 ::= { phivCircuitCountTable 1 }
1536
1537 PhivCircuitCountEntry ::=
1538 SEQUENCE {
1539 phivCircuitCountSecLastZeroed
1540 PhivCounter (0..65535),
1541 phivCircuitCountTermPacketsRecd
1542 PhivCounter,
1543 phivCircuitCountOriginPackSent
1544 PhivCounter,
1545 phivCircuitCountTermCongLoss
1546 PhivCounter (0..65535),
1547 phivCircuitCountCorruptLoss
1548 PhivCounter (0..255),
1549 phivCircuitCountTransitPksRecd
1550 PhivCounter,
1551 phivCircuitCountTransitPkSent
1552 PhivCounter,
1553 phivCircuitCountTransitCongestLoss
1554 PhivCounter (0..65535),
1555 phivCircuitCountCircuitDown
1556 PhivCounter (0..255),
1557 phivCircuitCountInitFailure
1558 PhivCounter (0..255),
1559 phivCircuitCountAdjDown
1560 PhivCounter,
1561
1562
1563
1564 <span class="grey">DECnet Phase IV MIB Working Group [Page 28]</span></pre>
1565 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-29" ></span>
1566 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1567
1568
1569 phivCircuitCountPeakAdj
1570 PhivCounter,
1571 phivCircuitCountBytesRecd
1572 PhivCounter,
1573 phivCircuitCountBytesSent
1574 PhivCounter,
1575 phivCircuitCountDataBlocksRecd
1576 PhivCounter (0..65535),
1577 phivCircuitCountDataBlocksSent
1578 PhivCounter,
1579 phivCircuitCountUsrBuffUnav
1580 PhivCounter (0..65535)
1581 }
1582 phivCircuitCountSecLastZeroed OBJECT-TYPE
1583 SYNTAX PhivCounter (0..65535)
1584 ACCESS read-only
1585 STATUS mandatory
1586 DESCRIPTION
1587 "Number of seconds since the circuit counters for this
1588 circuit were last zeroed."
1589 ::= { phivCircuitCountEntry 1 }
1590
1591 phivCircuitCountTermPacketsRecd OBJECT-TYPE
1592 SYNTAX PhivCounter
1593 ACCESS read-only
1594 STATUS mandatory
1595 DESCRIPTION
1596 "Number of terminating packets received on this circuit."
1597 ::= { phivCircuitCountEntry 2 }
1598
1599 phivCircuitCountOriginPackSent OBJECT-TYPE
1600 SYNTAX PhivCounter
1601 ACCESS read-only
1602 STATUS mandatory
1603 DESCRIPTION
1604 "Number of originating packets sent on this circuit."
1605 ::= { phivCircuitCountEntry 3 }
1606
1607 phivCircuitCountTermCongLoss OBJECT-TYPE
1608 SYNTAX PhivCounter
1609 ACCESS read-only
1610 STATUS mandatory
1611 DESCRIPTION
1612 "Number of terminating congestion losses on this
1613 circuit."
1614 ::= { phivCircuitCountEntry 4 }
1615
1616
1617
1618
1619
1620 <span class="grey">DECnet Phase IV MIB Working Group [Page 29]</span></pre>
1621 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-30" ></span>
1622 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1623
1624
1625 phivCircuitCountCorruptLoss OBJECT-TYPE
1626 SYNTAX PhivCounter (0..255)
1627 ACCESS read-only
1628 STATUS mandatory
1629 DESCRIPTION
1630 "Number of corruption losses on this circuit."
1631 ::= { phivCircuitCountEntry 5 }
1632
1633 phivCircuitCountTransitPksRecd OBJECT-TYPE
1634 SYNTAX PhivCounter
1635 ACCESS read-only
1636 STATUS mandatory
1637 DESCRIPTION
1638 "Number of Transit packets received on this circuit."
1639 ::= { phivCircuitCountEntry 6 }
1640
1641 phivCircuitCountTransitPkSent OBJECT-TYPE
1642 SYNTAX PhivCounter
1643 ACCESS read-only
1644 STATUS mandatory
1645 DESCRIPTION
1646 "Number of transit packets sent on this circuit."
1647 ::= { phivCircuitCountEntry 7 }
1648
1649 phivCircuitCountTransitCongestLoss OBJECT-TYPE
1650 SYNTAX PhivCounter (0..65535)
1651 ACCESS read-only
1652 STATUS mandatory
1653 DESCRIPTION
1654 "Number of transit congestion losses on this circuit."
1655 ::= { phivCircuitCountEntry 8 }
1656
1657 phivCircuitCountCircuitDown OBJECT-TYPE
1658 SYNTAX PhivCounter (0..255)
1659 ACCESS read-only
1660 STATUS mandatory
1661 DESCRIPTION
1662 "Number of circuit downs on this circuit."
1663 ::= { phivCircuitCountEntry 9 }
1664
1665 phivCircuitCountInitFailure OBJECT-TYPE
1666 SYNTAX PhivCounter (0..255)
1667 ACCESS read-only
1668 STATUS mandatory
1669 DESCRIPTION
1670 "Number of Initialization failures on this circuit."
1671 ::= { phivCircuitCountEntry 10 }
1672
1673
1674
1675
1676 <span class="grey">DECnet Phase IV MIB Working Group [Page 30]</span></pre>
1677 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-31" ></span>
1678 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1679
1680
1681 phivCircuitCountAdjDown OBJECT-TYPE
1682 SYNTAX PhivCounter
1683 ACCESS read-only
1684 STATUS mandatory
1685 DESCRIPTION
1686 "This counter indicates the number of adjacency losses
1687 that result from any of the following:
1688 Node listener timeout
1689 Invalid data received at node listener
1690 Unexpected control (initialization or verification)
1691 message received
1692 Routing message received with a checksum error
1693 Node identification from a routing message or a
1694 Hello message that is not the one expected Hello
1695 message received indicating that connectivity
1696 became one-way
1697 Adjacency idled."
1698 ::= { phivCircuitCountEntry 11 }
1699
1700 phivCircuitCountPeakAdj OBJECT-TYPE
1701 SYNTAX PhivCounter
1702 ACCESS read-only
1703 STATUS mandatory
1704 DESCRIPTION
1705 "This counter indicates the maximum number of nodes
1706 that are up on the circuit."
1707 ::= { phivCircuitCountEntry 12 }
1708
1709 phivCircuitCountBytesRecd OBJECT-TYPE
1710 SYNTAX PhivCounter
1711 ACCESS read-only
1712 STATUS mandatory
1713 DESCRIPTION
1714 "Number of bytes received on this circuit."
1715 ::= { phivCircuitCountEntry 13 }
1716
1717 phivCircuitCountBytesSent OBJECT-TYPE
1718 SYNTAX PhivCounter
1719 ACCESS read-only
1720 STATUS mandatory
1721 DESCRIPTION
1722 "Number of bytes sent on this circuit."
1723 ::= { phivCircuitCountEntry 14 }
1724
1725 phivCircuitCountDataBlocksRecd OBJECT-TYPE
1726 SYNTAX PhivCounter
1727 ACCESS read-only
1728 STATUS mandatory
1729
1730
1731
1732 <span class="grey">DECnet Phase IV MIB Working Group [Page 31]</span></pre>
1733 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-32" ></span>
1734 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1735
1736
1737 DESCRIPTION
1738 "Number of data blocks received on this circuit."
1739 ::= { phivCircuitCountEntry 15 }
1740
1741 phivCircuitCountDataBlocksSent OBJECT-TYPE
1742 SYNTAX PhivCounter
1743 ACCESS read-only
1744 STATUS mandatory
1745 DESCRIPTION
1746 "Number of data blocks sent on this circuit."
1747 ::= { phivCircuitCountEntry 16 }
1748
1749 phivCircuitCountUsrBuffUnav OBJECT-TYPE
1750 SYNTAX PhivCounter (0..65535)
1751 ACCESS read-only
1752 STATUS mandatory
1753 DESCRIPTION
1754 "Number of user buffer unavailable errors."
1755 ::= { phivCircuitCountEntry 17 }
1756
1757 -- Additional Circuit Parameters
1758
1759 phivCircuitOrigQueueLimit OBJECT-TYPE
1760 SYNTAX INTEGER
1761 ACCESS read-write
1762 STATUS mandatory
1763 DESCRIPTION
1764 "This parameter indicates the maximum number of
1765 originating packets that may be outstanding on this
1766 circuit. This does not include route-thru traffic."
1767 ::= { circuit 3 }
1768
1769 phivCircuitCountZeroCount OBJECT-TYPE
1770 SYNTAX INTEGER {
1771 other (1),
1772 reset (2)
1773 }
1774 ACCESS read-write
1775 STATUS mandatory
1776 DESCRIPTION
1777 "When this value is set to 2, all of the counters in the
1778 Circuit Counter Table are set to zero."
1779 ::= { circuit 4 }
1780
1781 -- DDCMP Circuit Group
1782
1783 -- The implementation of the DDCMP Circuit Group is mandatory for
1784 -- all systems which support DDCMP circuits.
1785
1786
1787
1788 <span class="grey">DECnet Phase IV MIB Working Group [Page 32]</span></pre>
1789 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-33" ></span>
1790 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1791
1792
1793
1794 -- DDCMP Parameters Table
1795
1796 phivDDCMPCircuitParametersTable OBJECT-TYPE
1797 SYNTAX SEQUENCE OF PhivDDCMPCircuitParametersEntry
1798 ACCESS not-accessible
1799 STATUS mandatory
1800 DESCRIPTION
1801 "Information about DDCMP circuit parameters."
1802 ::= { ddcmp 1}
1803
1804 phivDDCMPCircuitParametersEntry OBJECT-TYPE
1805 SYNTAX PhivDDCMPCircuitParametersEntry
1806 ACCESS not-accessible
1807 STATUS mandatory
1808 DESCRIPTION
1809 "Parameters information about DDCMP circuits currently
1810 known."
1811 INDEX { phivDDCMPCircuitIndex }
1812 ::= { phivDDCMPCircuitParametersTable 1 }
1813
1814 PhivDDCMPCircuitParametersEntry ::=
1815 SEQUENCE {
1816 phivDDCMPCircuitIndex
1817 INTEGER,
1818 phivDDCMPCircuitAdjNodeAddr
1819 INTEGER (0..65535),
1820 phivDDCMPCircuitTributary
1821 INTEGER (0..255)
1822 }
1823 phivDDCMPCircuitIndex OBJECT-TYPE
1824 SYNTAX INTEGER
1825 ACCESS read-only
1826 STATUS mandatory
1827 DESCRIPTION
1828 "A unique index value for each known DDCMP circuit.
1829 This is the same value as phivCircuitIndex."
1830 ::= { phivDDCMPCircuitParametersEntry 1 }
1831
1832 phivDDCMPCircuitAdjNodeAddr OBJECT-TYPE
1833 SYNTAX PhivAddr -- OCTET STRING (SIZE (2))
1834 ACCESS read-only
1835 STATUS mandatory
1836 DESCRIPTION
1837 "The address of the adjacent node."
1838 ::= { phivDDCMPCircuitParametersEntry 2 }
1839
1840
1841
1842
1843
1844 <span class="grey">DECnet Phase IV MIB Working Group [Page 33]</span></pre>
1845 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-34" ></span>
1846 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1847
1848
1849 phivDDCMPCircuitTributary OBJECT-TYPE
1850 SYNTAX INTEGER (0..255)
1851 ACCESS read-only
1852 STATUS mandatory
1853 DESCRIPTION
1854 "This value represents the Data Link physical tributary
1855 address of the circuit."
1856 ::= { phivDDCMPCircuitParametersEntry 3 }
1857
1858 -- DDCMP Circuit Counter Table
1859
1860 phivDDCMPCircuitCountTable OBJECT-TYPE
1861 SYNTAX SEQUENCE OF PhivDDCMPCircuitCountEntry
1862 ACCESS not-accessible
1863 STATUS mandatory
1864 DESCRIPTION
1865 "Information about the DDCMP counters associated with all
1866 circuits currently known."
1867 ::= { ddcmp 2 }
1868
1869 phivDDCMPCircuitCountEntry OBJECT-TYPE
1870 SYNTAX PhivDDCMPCircuitCountEntry
1871 ACCESS not-accessible
1872 STATUS mandatory
1873 DESCRIPTION
1874 "Counter information about DDCMP circuits now known"
1875 INDEX { phivCircuitIndex }
1876 ::= { phivDDCMPCircuitCountTable 1 }
1877
1878 PhivDDCMPCircuitCountEntry ::=
1879 SEQUENCE {
1880 phivDDCMPCircuitErrorsInbd
1881 PhivCounter (0..255),
1882 phivDDCMPCircuitErrorsOutbd
1883 PhivCounter (0..255),
1884 phivDDCMPCircuitRmteReplyTimeouts
1885 PhivCounter (0..255),
1886 phivDDCMPCircuitLocalReplyTimeouts
1887 PhivCounter (0..255),
1888 phivDDCMPCircuitRmteBuffErrors
1889 PhivCounter (0..255),
1890 phivDDCMPCircuitLocalBuffErrors
1891 PhivCounter (0..255),
1892 phivDDCMPCircuitSelectIntervalsElap
1893 PhivCounter (0..65535),
1894 phivDDCMPCircuitSelectTimeouts
1895 PhivCounter (0..255)
1896 }
1897
1898
1899
1900 <span class="grey">DECnet Phase IV MIB Working Group [Page 34]</span></pre>
1901 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-35" ></span>
1902 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1903
1904
1905 phivDDCMPCircuitErrorsInbd OBJECT-TYPE
1906 SYNTAX PhivCounter (0..255)
1907 ACCESS read-only
1908 STATUS mandatory
1909 DESCRIPTION
1910 "Number of Data errors inbound."
1911 ::= { phivDDCMPCircuitCountEntry 1 }
1912
1913 phivDDCMPCircuitErrorsOutbd OBJECT-TYPE
1914 SYNTAX PhivCounter (0..255)
1915 ACCESS read-only
1916 STATUS mandatory
1917 DESCRIPTION
1918 "Number of outbound data errors."
1919 ::= { phivDDCMPCircuitCountEntry 2 }
1920
1921 phivDDCMPCircuitRmteReplyTimeouts OBJECT-TYPE
1922 SYNTAX PhivCounter (0..255)
1923 ACCESS read-only
1924 STATUS mandatory
1925 DESCRIPTION
1926 "Number of remote reply timeouts."
1927 ::= { phivDDCMPCircuitCountEntry 3 }
1928
1929 phivDDCMPCircuitLocalReplyTimeouts OBJECT-TYPE
1930 SYNTAX PhivCounter (0..255)
1931 ACCESS read-only
1932 STATUS mandatory
1933 DESCRIPTION
1934 "Number of local Reply timeouts."
1935 ::= { phivDDCMPCircuitCountEntry 4 }
1936
1937 phivDDCMPCircuitRmteBuffErrors OBJECT-TYPE
1938 SYNTAX PhivCounter (0..255)
1939 ACCESS read-only
1940 STATUS mandatory
1941 DESCRIPTION
1942 "Number of remote reply time out errors."
1943 ::= { phivDDCMPCircuitCountEntry 5 }
1944
1945 phivDDCMPCircuitLocalBuffErrors OBJECT-TYPE
1946 SYNTAX PhivCounter (0..255)
1947 ACCESS read-only
1948 STATUS mandatory
1949 DESCRIPTION
1950 "Number of local buffer errors."
1951 ::= { phivDDCMPCircuitCountEntry 6 }
1952
1953
1954
1955
1956 <span class="grey">DECnet Phase IV MIB Working Group [Page 35]</span></pre>
1957 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-36" ></span>
1958 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
1959
1960
1961 phivDDCMPCircuitSelectIntervalsElap OBJECT-TYPE
1962 SYNTAX PhivCounter (0..65535)
1963 ACCESS read-only
1964 STATUS mandatory
1965 DESCRIPTION
1966 "Selection intervals that have elapsed."
1967 ::= {phivDDCMPCircuitCountEntry 7 }
1968
1969 phivDDCMPCircuitSelectTimeouts OBJECT-TYPE
1970 SYNTAX INTEGER (0..255)
1971 ACCESS read-only
1972 STATUS mandatory
1973 DESCRIPTION
1974 "Number of selection timeouts."
1975 ::= {phivDDCMPCircuitCountEntry 8 }
1976
1977 -- DDCMP Line Count Table
1978
1979 phivDDCMPLineCountTable OBJECT-TYPE
1980 SYNTAX SEQUENCE OF PhivDDCMPLineCountEntry
1981 ACCESS not-accessible
1982 STATUS mandatory
1983 DESCRIPTION
1984 "The DDCMP Line Count Table."
1985 ::= { ddcmp 3 }
1986
1987 phivDDCMPLineCountEntry OBJECT-TYPE
1988 SYNTAX PhivDDCMPLineCountEntry
1989 ACCESS not-accessible
1990 STATUS mandatory
1991 DESCRIPTION
1992 "There is one entry in the table for each line."
1993 INDEX { phivDDCMPLineCountIndex }
1994 ::= { phivDDCMPLineCountTable 1 }
1995
1996 PhivDDCMPLineCountEntry ::=
1997 SEQUENCE {
1998 phivDDCMPLineCountIndex
1999 INTEGER,
2000 phivDDCMPLineCountDataErrsIn
2001 PhivCounter (0..255),
2002 phivDDCMPLineCountRmteStationErrs
2003 PhivCounter (0..255),
2004 phivDDCMPLineCountLocalStationErrs
2005 PhivCounter (0..255)
2006 }
2007
2008
2009
2010
2011
2012 <span class="grey">DECnet Phase IV MIB Working Group [Page 36]</span></pre>
2013 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-37" ></span>
2014 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2015
2016
2017 phivDDCMPLineCountIndex OBJECT-TYPE
2018 SYNTAX INTEGER
2019 ACCESS read-only
2020 STATUS mandatory
2021 DESCRIPTION
2022 "The line on which this entry's equivalence is
2023 effective. The interface identified by a particular
2024 value of this index is the same interface as
2025 identified by the same value of phivLineIndex.
2026 This value is the IfIndex."
2027 ::= { phivDDCMPLineCountEntry 1 }
2028
2029 phivDDCMPLineCountDataErrsIn OBJECT-TYPE
2030 SYNTAX PhivCounter ( 0..255 )
2031 ACCESS read-only
2032 STATUS mandatory
2033 DESCRIPTION
2034 "Number of data errors inbound."
2035 ::= { phivDDCMPLineCountEntry 2 }
2036
2037 phivDDCMPLineCountRmteStationErrs OBJECT-TYPE
2038 SYNTAX PhivCounter ( 0..255 )
2039 ACCESS read-only
2040 STATUS mandatory
2041 DESCRIPTION
2042 "Number of remote station errors."
2043 ::= { phivDDCMPLineCountEntry 3 }
2044
2045 phivDDCMPLineCountLocalStationErrs OBJECT-TYPE
2046 SYNTAX PhivCounter ( 0..255 )
2047 ACCESS read-only
2048 STATUS mandatory
2049 DESCRIPTION
2050 "Number of local station errors."
2051 ::= { phivDDCMPLineCountEntry 4 }
2052
2053 -- DDCMP Multipoint Circuit Control Group
2054
2055 -- The implementation of the DDCMP Multipoint Circuit Control
2056 -- Group is mandatory for all systems which support DDCMP
2057 -- multipoint control circuits.
2058
2059 phivControlSchedTimer OBJECT-TYPE
2060 SYNTAX INTEGER (50..65535)
2061 ACCESS read-only
2062 STATUS mandatory
2063 DESCRIPTION
2064 "This value represents the number of milliseconds
2065
2066
2067
2068 <span class="grey">DECnet Phase IV MIB Working Group [Page 37]</span></pre>
2069 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-38" ></span>
2070 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2071
2072
2073 between recalculation of tributary polling priorities."
2074 DEFVAL { 200 }
2075 ::= { control 1 }
2076
2077 phivControlDeadTimer OBJECT-TYPE
2078 SYNTAX INTEGER (1..65535)
2079 ACCESS read-only
2080 STATUS mandatory
2081 DESCRIPTION
2082 "This value represents the number of milliseconds
2083 between polls of one of the set of dead
2084 tributaries."
2085 DEFVAL { 10000 }
2086 ::= { control 2 }
2087
2088 phivControlDelayTimer OBJECT-TYPE
2089 SYNTAX INTEGER (1..65535)
2090 ACCESS read-only
2091 STATUS mandatory
2092 DESCRIPTION
2093 "This value represents the minimum number of
2094 milliseconds to delay between polls. The delay timer
2095 limits the effect of a very fast control station on
2096 slow tributaries."
2097 ::= { control 3 }
2098
2099 phivControlStreamTimer OBJECT-TYPE
2100 SYNTAX INTEGER (0..65535)
2101 ACCESS read-only
2102 STATUS mandatory
2103 DESCRIPTION
2104 "This value represents the number of milliseconds a
2105 tributary or a half duplex remote station is
2106 allowed to hold the line.
2107
2108 NOTE: This parameter can also be applied to
2109 half-duplex lines of type DDCMP POINT."
2110 DEFVAL { 6000 }
2111 ::= { control 4 }
2112
2113 -- DDCMP Multipoint Circuit Control Parameters Table
2114
2115 phivControlParametersTable OBJECT-TYPE
2116 SYNTAX SEQUENCE OF PhivControlParametersEntry
2117 ACCESS not-accessible
2118 STATUS mandatory
2119 DESCRIPTION
2120 "Information about control circuit parameters."
2121
2122
2123
2124 <span class="grey">DECnet Phase IV MIB Working Group [Page 38]</span></pre>
2125 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-39" ></span>
2126 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2127
2128
2129 ::= { control 5 }
2130
2131 phivControlParametersEntry OBJECT-TYPE
2132 SYNTAX PhivControlParametersEntry
2133 ACCESS not-accessible
2134 STATUS mandatory
2135 DESCRIPTION
2136 "Parameters information about control circuits
2137 currently known."
2138 INDEX { phivControlCircuitIndex }
2139 ::= { phivControlParametersTable 1 }
2140
2141 PhivControlParametersEntry ::=
2142 SEQUENCE {
2143 phivControlCircuitIndex
2144 INTEGER,
2145 phivControlBabbleTimer
2146 INTEGER (1..65535),
2147 phivControlMaxBuffs
2148 INTEGER (0..254),
2149 phivControlMaxTransmits
2150 INTEGER (1..255),
2151 phivControlDyingBase
2152 INTEGER (0..255),
2153 phivControlDyingIncrement
2154 INTEGER (0..255),
2155 phivControlDeadThreshold
2156 INTEGER (0..255),
2157 phivControlDyingThreshold
2158 INTEGER (0..255),
2159 phivControlInactTreshold
2160 INTEGER (0..255),
2161 phivControlPollingState
2162 INTEGER,
2163 phivControlPollingSubState
2164 INTEGER,
2165 phivControlTransTimer
2166 INTEGER (0..65535)
2167 }
2168 phivControlCircuitIndex OBJECT-TYPE
2169 SYNTAX INTEGER
2170 ACCESS read-only
2171 STATUS mandatory
2172 DESCRIPTION
2173 "A unique index value for each known multirpoint
2174 control circuit.
2175 This is the same value as phivCircuitIndex."
2176 ::= { phivControlParametersEntry 1 }
2177
2178
2179
2180 <span class="grey">DECnet Phase IV MIB Working Group [Page 39]</span></pre>
2181 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-40" ></span>
2182 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2183
2184
2185
2186 phivControlBabbleTimer OBJECT-TYPE
2187 SYNTAX INTEGER (1..65535)
2188 ACCESS read-write
2189 STATUS mandatory
2190 DESCRIPTION
2191 "This value represents the number of milliseconds that a
2192 selected tributary or remote half-duplex station is
2193 allowed to transmit."
2194 DEFVAL { 6000 }
2195 ::= { phivControlParametersEntry 2 }
2196
2197 phivControlMaxBuffs OBJECT-TYPE
2198 SYNTAX INTEGER (0..254)
2199 ACCESS read-write
2200 STATUS mandatory
2201 DESCRIPTION
2202 "This value represents the maximum number of buffers the
2203 tributary can use from a common buffer pool. If not
2204 set, there is no common buffer pool and buffers are
2205 explicitly supplied by the higher level. Count is a
2206 decimal integer in the range 1-254."
2207 ::= { phivControlParametersEntry 3 }
2208
2209 phivControlMaxTransmits OBJECT-TYPE
2210 SYNTAX INTEGER (1..255)
2211 ACCESS read-write
2212 STATUS mandatory
2213 DESCRIPTION
2214 "This value represents the maximum number of data
2215 messages that can be transmitted at one time. Count
2216 is a decimal integer in the range 1-255."
2217 DEFVAL { 4 }
2218 ::= { phivControlParametersEntry 4 }
2219
2220 phivControlDyingBase OBJECT-TYPE
2221 SYNTAX INTEGER (0..255)
2222 ACCESS read-write
2223 STATUS mandatory
2224 DESCRIPTION
2225 "This value represents the base priority to which a
2226 tributary is reset each time it has been polled. A
2227 separate base can be set for each of the indicated
2228 polling states. Base is a decimal integer in the range
2229 0-255. If not set, the defaults are: active, 255;
2230 inactive, 0; and dying, 0."
2231 ::= { phivControlParametersEntry 5 }
2232
2233
2234
2235
2236 <span class="grey">DECnet Phase IV MIB Working Group [Page 40]</span></pre>
2237 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-41" ></span>
2238 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2239
2240
2241 phivControlDyingIncrement OBJECT-TYPE
2242 SYNTAX INTEGER (0..255)
2243 ACCESS read-write
2244 STATUS mandatory
2245 DESCRIPTION
2246 "This value represents the increment added to the
2247 tributary priority each time the scheduling timer
2248 expires. If not set, the defaults are: active, 0;
2249 inactive, 64; and dying, 16."
2250 ::= { phivControlParametersEntry 6 }
2251
2252 phivControlDeadThreshold OBJECT-TYPE
2253 SYNTAX INTEGER (0..255)
2254 ACCESS read-write
2255 STATUS mandatory
2256 DESCRIPTION
2257 "This value represents the number of times to poll the
2258 active, inactive, or dying tributary before changing
2259 its polling state to dead because of receive timeouts.
2260 Count is a decimal integer in the range 0-255."
2261 DEFVAL { 8 }
2262 ::= { phivControlParametersEntry 7 }
2263
2264 phivControlDyingThreshold OBJECT-TYPE
2265 SYNTAX INTEGER (0..255)
2266 ACCESS read-write
2267 STATUS mandatory
2268 DESCRIPTION
2269 "This value represents the number of times to poll the
2270 active or inactive tributary before changing its
2271 polling state to dying because of receive timeouts.
2272 Count is a decimal integer in the range 0-255."
2273 DEFVAL { 2 }
2274 ::= { phivControlParametersEntry 8 }
2275
2276 phivControlInactTreshold OBJECT-TYPE
2277 SYNTAX INTEGER (0..255)
2278 ACCESS read-write
2279 STATUS mandatory
2280 DESCRIPTION
2281 "This value represents the number of times to poll the
2282 active tributary before changing its polling state to
2283 inactive because of no data response. Count is a
2284 decimal integer in the range
2285 0-255."
2286 DEFVAL { 8 }
2287 ::= { phivControlParametersEntry 9 }
2288
2289
2290
2291
2292 <span class="grey">DECnet Phase IV MIB Working Group [Page 41]</span></pre>
2293 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-42" ></span>
2294 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2295
2296
2297 phivControlPollingState OBJECT-TYPE
2298 SYNTAX INTEGER {
2299 automatic (1),
2300 active (2),
2301 inactive (3),
2302 dying (4),
2303 dead (5)
2304 }
2305 ACCESS read-write
2306 STATUS mandatory
2307 DESCRIPTION
2308 "This value represents the state of the tributary
2309 relative to the multipoint polling algorithm. If not
2310 set the default is AUTOMATIC. The possible states are:
2311
2312 AUTOMATIC
2313
2314 The tributary's state is allowed to vary according to
2315 the operation of the polling algorithm.
2316
2317 ACTIVE/INACTIVE/DYING/DEAD
2318
2319 The tributary is locked in the specified state.
2320
2321 NOTE: These values are incremented by one compared to
2322 the standard DECnet values in order to maintain
2323 compliance with <a href="./rfc1155">RFC 1155</a>."
2324 ::= { phivControlParametersEntry 10 }
2325
2326 phivControlPollingSubState OBJECT-TYPE
2327 SYNTAX INTEGER {
2328 active (1),
2329 inactive (2),
2330 dying (3),
2331 dead (4)
2332 }
2333 ACCESS read-only
2334 STATUS mandatory
2335 DESCRIPTION
2336 "This value represents the tributary's state as
2337 determined by the polling algorithm. This applies
2338 only when the polling state is AUTOMATIC and is
2339 read-only to Network Management. Polling-substate is
2340 one of ACTIVE, INACTIVE, DYING, or DEAD. It is
2341 displayed as a tag on the polling state, for example:
2342 AUTOMATIC-INACTIVE."
2343 ::= { phivControlParametersEntry 11 }
2344
2345
2346
2347
2348 <span class="grey">DECnet Phase IV MIB Working Group [Page 42]</span></pre>
2349 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-43" ></span>
2350 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2351
2352
2353 phivControlTransTimer OBJECT-TYPE
2354 SYNTAX INTEGER (0..65535)
2355 ACCESS read-write
2356 STATUS mandatory
2357 DESCRIPTION
2358 "This value represents the number of milliseconds to
2359 delay between data message transmits. Milliseconds is
2360 a decimal integer in the range 0-65535."
2361 DEFVAL { 0 }
2362 ::= { phivControlParametersEntry 12 }
2363
2364 -- Ethernet Group
2365
2366 -- The implementation of the Ethernet Group is mandatory
2367 -- for all systems which support ethernet links.
2368
2369 -- Ethernet Parameters Table
2370
2371 phivEthLinkParametersTable OBJECT-TYPE
2372 SYNTAX SEQUENCE OF PhivEthLinkParametersEntry
2373 ACCESS not-accessible
2374 STATUS mandatory
2375 DESCRIPTION
2376 "Information about ethernet link parameters."
2377 ::= { ethernet 1}
2378
2379 phivEthLinkParametersEntry OBJECT-TYPE
2380 SYNTAX PhivEthLinkParametersEntry
2381 ACCESS not-accessible
2382 STATUS mandatory
2383 DESCRIPTION
2384 "Parameter information about ethernet links currently
2385 known."
2386 INDEX { phivEthLinkIndex }
2387 ::= { phivEthLinkParametersTable 1 }
2388
2389 PhivEthLinkParametersEntry ::=
2390 SEQUENCE {
2391 phivEthLinkIndex
2392 INTEGER,
2393 phivEthDesigRouterNodeAddr
2394 PhivAddr,
2395 phivEthMaxRouters
2396 INTEGER (0..255),
2397 phivEthRouterPri
2398 INTEGER (0..127),
2399 phivEthHardwareAddr
2400 OCTET STRING
2401
2402
2403
2404 <span class="grey">DECnet Phase IV MIB Working Group [Page 43]</span></pre>
2405 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-44" ></span>
2406 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2407
2408
2409 }
2410 phivEthLinkIndex OBJECT-TYPE
2411 SYNTAX INTEGER
2412 ACCESS read-only
2413 STATUS mandatory
2414 DESCRIPTION
2415 "The circuit over which this links information is
2416 collected. This is the same as phivCircuitIndex."
2417 ::= { phivEthLinkParametersEntry 1 }
2418
2419 phivEthDesigRouterNodeAddr OBJECT-TYPE
2420 SYNTAX PhivAddr -- OCTET STRING (SIZE (2))
2421 ACCESS read-only
2422 STATUS mandatory
2423 DESCRIPTION
2424 "This value is the address of the designated router."
2425 ::= { phivEthLinkParametersEntry 2 }
2426
2427 phivEthMaxRouters OBJECT-TYPE
2428 SYNTAX INTEGER (0..255)
2429 ACCESS read-write
2430 STATUS mandatory
2431 DESCRIPTION
2432 "This parameter is the maximum number of routers (other
2433 than the executor itself) allowed on the circuit by
2434 Routing for circuits that are owned by the executor
2435 node."
2436 ::= { phivEthLinkParametersEntry 3 }
2437
2438 phivEthRouterPri OBJECT-TYPE
2439 SYNTAX INTEGER (0..127)
2440 ACCESS read-write
2441 STATUS mandatory
2442 DESCRIPTION
2443 "This parameter is the priority that this router is to
2444 have in the selection of designated router for the
2445 circuit on circuits that are owned by the executor
2446 node."
2447 DEFVAL { 64 }
2448 ::= { phivEthLinkParametersEntry 4 }
2449
2450 phivEthHardwareAddr OBJECT-TYPE
2451 SYNTAX OCTET STRING ( SIZE (6) )
2452 ACCESS read-only
2453 STATUS mandatory
2454 DESCRIPTION
2455 "This read-only parameter is the address that is
2456 associated with the line device hardware as seen by
2457
2458
2459
2460 <span class="grey">DECnet Phase IV MIB Working Group [Page 44]</span></pre>
2461 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-45" ></span>
2462 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2463
2464
2465 the DECnet Software. This value is not the same as
2466 ifPhysAddress."
2467 ::= { phivEthLinkParametersEntry 5 }
2468
2469 -- Counters Group
2470
2471 -- The implementation of the Counters Group is mandatory for
2472 -- systems which only support DECnet style locking counters.
2473
2474 -- Counters Table
2475
2476 phivCountersCountTable OBJECT-TYPE
2477 SYNTAX SEQUENCE OF PhivCountersCountEntry
2478 ACCESS not-accessible
2479 STATUS mandatory
2480 DESCRIPTION
2481 "Information about ethernet link counters."
2482 ::= { counters 1 }
2483
2484 phivCountersCountEntry OBJECT-TYPE
2485 SYNTAX PhivCountersCountEntry
2486 ACCESS not-accessible
2487 STATUS mandatory
2488 DESCRIPTION
2489 "Counter information about ethernet links currently
2490 known.."
2491 INDEX { phivCountersIndex }
2492 ::= { phivCountersCountTable 1 }
2493
2494 PhivCountersCountEntry ::=
2495 SEQUENCE {
2496 phivCountersIndex
2497 INTEGER,
2498 phivCountersCountBytesRecd
2499 PhivCounter,
2500 phivCountersCountBytesSent
2501 PhivCounter,
2502 phivCountersCountDataBlocksRecd
2503 PhivCounter,
2504 phivCountersCountDataBlocksSent
2505 PhivCounter,
2506 phivCountersCountEthUsrBuffUnav
2507 PhivCounter (0..65535),
2508 phivCountersCountMcastBytesRecd
2509 PhivCounter,
2510 phivCountersCountDataBlksRecd
2511 PhivCounter,
2512 phivCountersCountDataBlksSent
2513
2514
2515
2516 <span class="grey">DECnet Phase IV MIB Working Group [Page 45]</span></pre>
2517 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-46" ></span>
2518 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2519
2520
2521 PhivCounter,
2522 phivCountersCountMcastBlksRecd
2523 PhivCounter,
2524 phivCountersCountBlksSentDef
2525 PhivCounter,
2526 phivCountersCountBlksSentSingleCol
2527 PhivCounter,
2528 phivCountersCountBlksSentMultCol
2529 PhivCounter,
2530 phivCountersCountSendFailure
2531 PhivCounter,
2532 phivCountersCountCollDetectFailure
2533 PhivCounter (0..65535),
2534 phivCountersCountReceiveFailure
2535 PhivCounter (0..65535),
2536 phivCountersCountUnrecFrameDest
2537 PhivCounter (0..65535),
2538 phivCountersCountDataOver
2539 PhivCounter (0..65535),
2540 phivCountersCountSysBuffUnav
2541 PhivCounter (0..65535),
2542 phivCountersCountUsrBuffUnav
2543 PhivCounter (0..65535)
2544 }
2545 phivCountersIndex OBJECT-TYPE
2546 SYNTAX INTEGER
2547 ACCESS read-only
2548 STATUS mandatory
2549 DESCRIPTION
2550 "The interface to which these counters apply. This is
2551 the same interface as identified by the same value of
2552 phivLineIndex. This value is the IfIndex."
2553 ::= { phivCountersCountEntry 1 }
2554
2555 phivCountersCountBytesRecd OBJECT-TYPE
2556 SYNTAX PhivCounter
2557 ACCESS read-only
2558 STATUS mandatory
2559 DESCRIPTION
2560 "Number of bytes received over this link."
2561 ::= { phivCountersCountEntry 2 }
2562
2563 phivCountersCountBytesSent OBJECT-TYPE
2564 SYNTAX PhivCounter
2565 ACCESS read-only
2566 STATUS mandatory
2567 DESCRIPTION
2568 "Number of bytes sent over this link."
2569
2570
2571
2572 <span class="grey">DECnet Phase IV MIB Working Group [Page 46]</span></pre>
2573 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-47" ></span>
2574 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2575
2576
2577 ::= { phivCountersCountEntry 3 }
2578
2579 phivCountersCountDataBlocksRecd OBJECT-TYPE
2580 SYNTAX PhivCounter
2581 ACCESS read-only
2582 STATUS mandatory
2583 DESCRIPTION
2584 "Number of data blocks received over this link."
2585 ::= { phivCountersCountEntry 4 }
2586
2587 phivCountersCountDataBlocksSent OBJECT-TYPE
2588 SYNTAX PhivCounter
2589 ACCESS read-only
2590 STATUS mandatory
2591 DESCRIPTION
2592 "Number of data blocks sent over this link."
2593 ::= { phivCountersCountEntry 5 }
2594
2595 phivCountersCountEthUsrBuffUnav OBJECT-TYPE
2596 SYNTAX PhivCounter (0..65535)
2597 ACCESS read-only
2598 STATUS mandatory
2599 DESCRIPTION
2600 "Number of user buffer unavailable errors over this
2601 link."
2602 ::= { phivCountersCountEntry 6 }
2603
2604 phivCountersCountMcastBytesRecd OBJECT-TYPE
2605 SYNTAX PhivCounter
2606 ACCESS read-only
2607 STATUS mandatory
2608 DESCRIPTION
2609 "Number of multicast bytes received over this link."
2610 ::= { phivCountersCountEntry 7 }
2611
2612 phivCountersCountDataBlksRecd OBJECT-TYPE
2613 SYNTAX PhivCounter
2614 ACCESS read-only
2615 STATUS mandatory
2616 DESCRIPTION
2617 "Number of data blocks received over this link."
2618 ::= { phivCountersCountEntry 8 }
2619
2620 phivCountersCountDataBlksSent OBJECT-TYPE
2621 SYNTAX PhivCounter
2622 ACCESS read-only
2623 STATUS mandatory
2624 DESCRIPTION
2625
2626
2627
2628 <span class="grey">DECnet Phase IV MIB Working Group [Page 47]</span></pre>
2629 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-48" ></span>
2630 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2631
2632
2633 "Number of data blocks sent over this link."
2634 ::= { phivCountersCountEntry 9 }
2635
2636 phivCountersCountMcastBlksRecd OBJECT-TYPE
2637 SYNTAX PhivCounter
2638 ACCESS read-only
2639 STATUS mandatory
2640 DESCRIPTION
2641 "Number of multicast blocks received over this link."
2642 ::= { phivCountersCountEntry 10 }
2643
2644 phivCountersCountBlksSentDef OBJECT-TYPE
2645 SYNTAX PhivCounter
2646 ACCESS read-only
2647 STATUS mandatory
2648 DESCRIPTION
2649 "Number of blocks sent, initially deferred over this
2650 link."
2651 ::= { phivCountersCountEntry 11 }
2652
2653 phivCountersCountBlksSentSingleCol OBJECT-TYPE
2654 SYNTAX PhivCounter
2655 ACCESS read-only
2656 STATUS mandatory
2657 DESCRIPTION
2658 "Number of blocks sent, single collision over this link."
2659 ::= { phivCountersCountEntry 12 }
2660
2661 phivCountersCountBlksSentMultCol OBJECT-TYPE
2662 SYNTAX PhivCounter
2663 ACCESS read-only
2664 STATUS mandatory
2665 DESCRIPTION
2666 "Number of blocks sent, multiple collisions over this
2667 link."
2668 ::= { phivCountersCountEntry 13 }
2669
2670 phivCountersCountSendFailure OBJECT-TYPE
2671 SYNTAX INTEGER ( 0..65535 )
2672 ACCESS read-only
2673 STATUS mandatory
2674 DESCRIPTION
2675 "Number of send failures over this link."
2676 ::= { phivCountersCountEntry 14 }
2677
2678 phivCountersCountCollDetectFailure OBJECT-TYPE
2679 SYNTAX INTEGER ( 0..65535 )
2680 ACCESS read-only
2681
2682
2683
2684 <span class="grey">DECnet Phase IV MIB Working Group [Page 48]</span></pre>
2685 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-49" ></span>
2686 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2687
2688
2689 STATUS mandatory
2690 DESCRIPTION
2691 "Number of collision detect check failures over this
2692 link."
2693 ::= { phivCountersCountEntry 15 }
2694
2695 phivCountersCountReceiveFailure OBJECT-TYPE
2696 SYNTAX INTEGER ( 0..65535 )
2697 ACCESS read-only
2698 STATUS mandatory
2699 DESCRIPTION
2700 "Number of receive failures over this link."
2701 ::= { phivCountersCountEntry 16 }
2702
2703 phivCountersCountUnrecFrameDest OBJECT-TYPE
2704 SYNTAX INTEGER ( 0..65535 )
2705 ACCESS read-only
2706 STATUS mandatory
2707 DESCRIPTION
2708 "Number of unrecognized frame destinations over this
2709 link."
2710 ::= { phivCountersCountEntry 17 }
2711
2712 phivCountersCountDataOver OBJECT-TYPE
2713 SYNTAX INTEGER ( 0..65535 )
2714 ACCESS read-only
2715 STATUS mandatory
2716 DESCRIPTION
2717 "Number of data overruns over this link."
2718 ::= { phivCountersCountEntry 18 }
2719
2720 phivCountersCountSysBuffUnav OBJECT-TYPE
2721 SYNTAX INTEGER ( 0..65535 )
2722 ACCESS read-only
2723 STATUS mandatory
2724 DESCRIPTION
2725 "Number of system buffer unavailables over this link."
2726 ::= { phivCountersCountEntry 19 }
2727
2728 phivCountersCountUsrBuffUnav OBJECT-TYPE
2729 SYNTAX INTEGER ( 0..65535 )
2730 ACCESS read-only
2731 STATUS mandatory
2732 DESCRIPTION
2733 "Number of user buffer unavailables."
2734 ::= { phivCountersCountEntry 20 }
2735
2736
2737
2738
2739
2740 <span class="grey">DECnet Phase IV MIB Working Group [Page 49]</span></pre>
2741 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-50" ></span>
2742 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2743
2744
2745 -- Adjacency Group
2746
2747 -- The implementation of the Adjacency Group is mandatory for all
2748 -- conformant implementations of this memo.
2749
2750 phivAdjTable OBJECT-TYPE
2751 SYNTAX SEQUENCE OF PhivAdjEntry
2752 ACCESS not-accessible
2753 STATUS mandatory
2754 DESCRIPTION
2755 "The Adjacency Table."
2756 ::= { adjacency 1 }
2757
2758 phivAdjEntry OBJECT-TYPE
2759 SYNTAX PhivAdjEntry
2760 ACCESS not-accessible
2761 STATUS mandatory
2762 DESCRIPTION
2763 "There is one entry in the table for each adjacency."
2764 INDEX { phivAdjCircuitIndex }
2765 ::= { phivAdjTable 1 }
2766
2767 PhivAdjEntry ::=
2768 SEQUENCE {
2769 phivAdjCircuitIndex
2770 INTEGER,
2771 phivAdjNodeAddr
2772 PhivAddr,
2773 phivAdjBlockSize
2774 INTEGER,
2775 phivAdjListenTimer
2776 INTEGER (1..65535),
2777 phivAdjCircuitEtherServPhysAddr
2778 OCTET STRING,
2779 phivAdjType
2780 INTEGER,
2781 phivAdjState
2782 INTEGER,
2783 phivAdjPriority
2784 INTEGER,
2785 phivAdjExecListenTimer
2786 INTEGER (1..65535)
2787 }
2788
2789 phivAdjCircuitIndex OBJECT-TYPE
2790 SYNTAX INTEGER
2791 ACCESS read-only
2792 STATUS mandatory
2793
2794
2795
2796 <span class="grey">DECnet Phase IV MIB Working Group [Page 50]</span></pre>
2797 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-51" ></span>
2798 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2799
2800
2801 DESCRIPTION
2802 "A unique index value for each known circuit."
2803 ::= { phivAdjEntry 1 }
2804
2805 phivAdjNodeAddr OBJECT-TYPE
2806 SYNTAX PhivAddr -- OCTET STRING (SIZE (2))
2807 ACCESS read-only
2808 STATUS mandatory
2809 DESCRIPTION
2810 "The address of the adjacent node."
2811 ::= { phivAdjEntry 2 }
2812
2813 phivAdjBlockSize OBJECT-TYPE
2814 SYNTAX INTEGER
2815 ACCESS read-only
2816 STATUS mandatory
2817 DESCRIPTION
2818 "This read-only parameter is the block size that was
2819 negotiated with the adjacent Routing layer during Routing
2820 initialization over a particular circuit. It includes the
2821 routing header, but excludes the data link header. This
2822 parameter is qualified by ADJACENT NODE."
2823 ::= { phivAdjEntry 3 }
2824
2825 phivAdjListenTimer OBJECT-TYPE
2826 SYNTAX INTEGER (1..65535)
2827 ACCESS read-only
2828 STATUS mandatory
2829 DESCRIPTION
2830 "This value determines the maximum number of seconds
2831 allowed to elapse before Routing receives some message
2832 (either a Hello message or a user message) from the
2833 adjacent node on the circuit. It was agreed during
2834 Routing initialization with the adjacent Routing layer.
2835 This parameter is qualified by ADJACENT NODE."
2836 ::= { phivAdjEntry 4 }
2837
2838 phivAdjCircuitEtherServPhysAddr OBJECT-TYPE
2839 SYNTAX OCTET STRING ( SIZE (6) )
2840 ACCESS read-only
2841 STATUS mandatory
2842 DESCRIPTION
2843 "This parameter indicates the Ethernet physical address
2844 of an adjacent node that is being serviced on this
2845 circuit. This parameter is a qualifier for SERVICE
2846 SUBSTATE."
2847 ::= { phivAdjEntry 5 }
2848
2849
2850
2851
2852 <span class="grey">DECnet Phase IV MIB Working Group [Page 51]</span></pre>
2853 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-52" ></span>
2854 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2855
2856
2857 phivAdjType OBJECT-TYPE
2858 SYNTAX INTEGER {
2859 routing-III (1),
2860 nonrouting-III (2),
2861 area (3),
2862 routing-IV (4),
2863 nonrouting-IV (5)
2864 }
2865 ACCESS read-only
2866 STATUS mandatory
2867 DESCRIPTION
2868 "This parameter indicates the type of adjacency.
2869
2870 For adjacent nodes, this is a read-only parameter that
2871 indicates the type of the reachable adjacent node.
2872 NOTE: The routing-III and nonrouting-III values are
2873 incremented by one compared to the standard DECnet
2874 values in order to maintain compliance with <a href="./rfc1155">RFC 1155</a>)"
2875 ::= { phivAdjEntry 6 }
2876
2877 phivAdjState OBJECT-TYPE
2878 SYNTAX INTEGER {
2879 initializing (1), -- Ethernet one-way
2880 up (2), -- Ethernet two-way
2881 run (3), -- The eight DDCMP/X.25 states
2882 circuit-rejected (4),
2883 data-link-start (5),
2884 routing-layer-initialize (6),
2885 routing-layer-verify (7),
2886 routing-layer-complete (8),
2887 off (9),
2888 halt (10)
2889 }
2890 ACCESS read-only
2891 STATUS mandatory
2892 DESCRIPTION
2893 "This value indicates the state of a router adjacency.
2894 On adjacencies over a circuit of type
2895 (phivCircuitCommonType) Ethernet, CI, or FDDI, with an
2896 adjacent node of type (phivAdjType) ROUTING IV or AREA,
2897 this variable is the state of the Ethernet
2898 Initialization Layer for this adjacency, and can have
2899 values INITIALIZING or UP. (See <a href="#section-9.1.1">Section 9.1.1</a> of
2900 DECnet Phase IV Routing Layer Functional Specification.)
2901
2902 On adjacencies over a circuit of type
2903 (phivCircuitCommonType) Ethernet, CI, or FDDI, with an
2904 adjacent node of type (phivAdjType) NONROUTING IV,
2905
2906
2907
2908 <span class="grey">DECnet Phase IV MIB Working Group [Page 52]</span></pre>
2909 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-53" ></span>
2910 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2911
2912
2913 this variable will always take on the value UP.
2914
2915 On adjacencies over a circuit of type
2916 (phivCircuitCommonType) DDCMP POINT, DDCMP CONTROL,
2917 DDCMP TRIBUTARY, DDCMP DMC, or X.25, this variable is
2918 the state of the Routing Layer Initialization Circuit
2919 State. (See <a href="#section-7.3">section 7.3</a>, ibid.) It can have values
2920 between RUN and HALT.
2921
2922 On adjacencies over a circuit of type
2923 (phivCircuitCommonType) OTHER, this variable may be
2924 used in a manner consistent with the Initialization
2925 Layer used on that circuit."
2926 ::= { phivAdjEntry 7 }
2927
2928 phivAdjPriority OBJECT-TYPE
2929 SYNTAX INTEGER (0..255)
2930 ACCESS read-only
2931 STATUS mandatory
2932 DESCRIPTION
2933 "Priority assigned by the adjacent node for this
2934 circuit."
2935 ::= { phivAdjEntry 8 }
2936
2937 phivAdjExecListenTimer OBJECT-TYPE
2938 SYNTAX INTEGER (1..65535)
2939 ACCESS read-only
2940 STATUS mandatory
2941 DESCRIPTION
2942 "This read-only value determines the maximum number of
2943 seconds allowed to elapse before Routing receives some
2944 message (either a Hello message or a user message) from
2945 the adjacent node on the circuit. It was agreed during
2946 Routing initialization with the adjacent Routing layer."
2947 ::= { phivAdjEntry 9 }
2948
2949 -- Line Group
2950
2951 -- The implementation of the Line Group is mandatory for all
2952 -- conformant implementations of this memo.
2953
2954 phivLineTable OBJECT-TYPE
2955 SYNTAX SEQUENCE OF PhivLineEntry
2956 ACCESS not-accessible
2957 STATUS mandatory
2958 DESCRIPTION
2959 "The Line Table."
2960 ::= { line 1 }
2961
2962
2963
2964 <span class="grey">DECnet Phase IV MIB Working Group [Page 53]</span></pre>
2965 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-54" ></span>
2966 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
2967
2968
2969
2970 phivLineEntry OBJECT-TYPE
2971 SYNTAX PhivLineEntry
2972 ACCESS not-accessible
2973 STATUS mandatory
2974 DESCRIPTION
2975 "There is one entry in the table for each line."
2976 INDEX { phivLineIndex }
2977 ::= { phivLineTable 1 }
2978
2979 PhivLineEntry ::=
2980 SEQUENCE {
2981 phivLineIndex
2982 INTEGER,
2983 phivLineName
2984 DisplayString,
2985 phivLineState
2986 INTEGER,
2987 phivLineSubstate
2988 INTEGER,
2989 phivLineService
2990 INTEGER,
2991 phivLineDevice
2992 DisplayString,
2993 phivLineReceiveBuffs
2994 INTEGER (0..65535),
2995 phivLineProtocol
2996 INTEGER,
2997 phivLineServiceTimer
2998 INTEGER (1..65535),
2999 phivLineMaxBlock
3000 INTEGER (1..65535)
3001 }
3002
3003 phivLineIndex OBJECT-TYPE
3004 SYNTAX INTEGER
3005 ACCESS read-only
3006 STATUS mandatory
3007 DESCRIPTION
3008 "The line on which this entry's equivalence is effective.
3009 This is the same as the IfIndex."
3010 ::= { phivLineEntry 1 }
3011
3012 phivLineName OBJECT-TYPE
3013 SYNTAX DisplayString ( SIZE (0..16) )
3014 ACCESS read-only
3015 STATUS mandatory
3016 DESCRIPTION
3017
3018
3019
3020 <span class="grey">DECnet Phase IV MIB Working Group [Page 54]</span></pre>
3021 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-55" ></span>
3022 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
3023
3024
3025 "The name of the line on this row of the table."
3026 ::= { phivLineEntry 2 }
3027
3028 phivLineState OBJECT-TYPE
3029 SYNTAX INTEGER {
3030 on (1),
3031 off (2),
3032 service (3),
3033 cleared (4)
3034 }
3035 ACCESS read-only
3036 STATUS mandatory
3037 DESCRIPTION
3038 "This value represents Network Management operational
3039 state.
3040 NOTE that these values are incremented by one compared to
3041 the standard DECnet values."
3042 ::= { phivLineEntry 3 }
3043
3044 phivLineSubstate OBJECT-TYPE
3045 SYNTAX INTEGER {
3046 starting (1),
3047 reflecting (2),
3048 looping (3),
3049 loading (4),
3050 dumping (5),
3051 triggering (6),
3052 auto-service (7),
3053 auto-loading (8),
3054 auto-dumping (9),
3055 auto-triggering (10),
3056 synchronizing (11),
3057 failed (12),
3058 running (13)
3059 }
3060 ACCESS read-only
3061 STATUS mandatory
3062 DESCRIPTION
3063 "This value represents the line's read-only Network
3064 Management substate.
3065 NOTE that these values are incremented by one compared to
3066 the standard DECnet values."
3067 ::= { phivLineEntry 4 }
3068
3069 phivLineService OBJECT-TYPE
3070 SYNTAX INTEGER {
3071 starting (1),
3072 reflecting (2),
3073
3074
3075
3076 <span class="grey">DECnet Phase IV MIB Working Group [Page 55]</span></pre>
3077 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-56" ></span>
3078 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
3079
3080
3081 looping (3),
3082 other (4)
3083 }
3084 ACCESS read-only
3085 STATUS mandatory
3086 DESCRIPTION
3087 "This value represents the line's read-only Network
3088 Management service.
3089 NOTE that these values are incremented by one compared to
3090 the standard DECnet values and OTHER is a new addition."
3091 ::= { phivLineEntry 5 }
3092
3093 phivLineDevice OBJECT-TYPE
3094 SYNTAX DisplayString ( SIZE (0..16) )
3095 ACCESS read-only
3096 STATUS mandatory
3097 DESCRIPTION
3098 "This value represents the Physical Link device to be
3099 used on the line."
3100 ::= { phivLineEntry 6 }
3101
3102 phivLineReceiveBuffs OBJECT-TYPE
3103 SYNTAX INTEGER (0..65535)
3104 ACCESS read-only
3105 STATUS mandatory
3106 DESCRIPTION
3107 "This value represents the number of receive buffers
3108 reserved for the line. It is a decimal number in
3109 the range 0-65535. 0 is supported for those vendors
3110 that do not reserve buffers on a per line basis and
3111 use a pool of buffers that can be used by any line."
3112 ::= { phivLineEntry 7 }
3113
3114 phivLineProtocol OBJECT-TYPE
3115 SYNTAX INTEGER {
3116 ddcmp-point (1),
3117 ddcmp-control (2),
3118 ddcmp-tributary (3),
3119 reserved (4),
3120 ddcmp-dmc (5),
3121 lapb (6),
3122 ethernet (7),
3123 ci (8),
3124 qp2 (9),
3125 other (14),
3126 fddi (15)
3127 }
3128 ACCESS read-only
3129
3130
3131
3132 <span class="grey">DECnet Phase IV MIB Working Group [Page 56]</span></pre>
3133 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-57" ></span>
3134 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
3135
3136
3137 STATUS mandatory
3138 DESCRIPTION
3139 "This value represents the protocol used on the line
3140 device. Note that these values are incremented by
3141 one compared to the standard DECnet values."
3142 ::= { phivLineEntry 8 }
3143
3144 phivLineServiceTimer OBJECT-TYPE
3145 SYNTAX INTEGER (1..65535)
3146 ACCESS read-only
3147 STATUS mandatory
3148 DESCRIPTION
3149 "This value represents the amount of time in
3150 milliseconds allowed to elapse before a Data Link
3151 receive request completes while doing service
3152 operations."
3153 ::= { phivLineEntry 9 }
3154
3155 phivLineMaxBlock OBJECT-TYPE
3156 SYNTAX INTEGER (1..65535)
3157 ACCESS read-only
3158 STATUS mandatory
3159 DESCRIPTION
3160 "This value represents the Data Link maximum block
3161 size on the line."
3162 ::= { phivLineEntry 10 }
3163
3164 -- Non Broadcast Line Group
3165
3166 -- The implementation of the Non Broadcast Line Group is
3167 -- mandatory for all systems which implement non broadcast
3168 -- lines.
3169
3170 phivNonBroadcastTable OBJECT-TYPE
3171 SYNTAX SEQUENCE OF PhivNonBroadcastEntry
3172 ACCESS not-accessible
3173 STATUS mandatory
3174 DESCRIPTION
3175 "The Non Broadcast Table."
3176 ::= { nonBroadcastLine 1 }
3177
3178 phivNonBroadcastEntry OBJECT-TYPE
3179 SYNTAX PhivNonBroadcastEntry
3180 ACCESS not-accessible
3181 STATUS mandatory
3182 DESCRIPTION
3183 "There is one entry in the table for each
3184 Non Broadcast line."
3185
3186
3187
3188 <span class="grey">DECnet Phase IV MIB Working Group [Page 57]</span></pre>
3189 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-58" ></span>
3190 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
3191
3192
3193 INDEX { phivNonBroadcastIndex }
3194 ::= { phivNonBroadcastTable 1 }
3195
3196 PhivNonBroadcastEntry ::=
3197 SEQUENCE {
3198 phivNonBroadcastIndex
3199 INTEGER,
3200 phivNonBroadcastController
3201 INTEGER,
3202 phivNonBroadcastDuplex
3203 INTEGER,
3204 phivNonBroadcastClock
3205 INTEGER,
3206 phivNonBroadcastRetransmitTimer
3207 INTEGER (1..65535)
3208 }
3209 phivNonBroadcastIndex OBJECT-TYPE
3210 SYNTAX INTEGER
3211 ACCESS read-only
3212 STATUS mandatory
3213 DESCRIPTION
3214 "The Non Broadcast line on which this entry's
3215 equivalence is effective. This is the same value
3216 as the IfIndex."
3217 ::= { phivNonBroadcastEntry 1 }
3218
3219 phivNonBroadcastController OBJECT-TYPE
3220 SYNTAX INTEGER {
3221 normal (1),
3222 loopback (2),
3223 other (3)
3224 }
3225 ACCESS read-only
3226 STATUS mandatory
3227 DESCRIPTION
3228 "This value represents the Physical Link hardware
3229 controller mode for the line device. The values
3230 for controller-mode are:
3231
3232 NORMAL For normal controller operating mode.
3233
3234 LOOPBACK For software controllable loopback of the
3235 controller. On those devices that can support this
3236 mode, it causes all transmitted messages to be looped
3237 back from within the controller itself. This is
3238 accomplished without any manual intervention other
3239 than the setting of this parameter value.
3240
3241
3242
3243
3244 <span class="grey">DECnet Phase IV MIB Working Group [Page 58]</span></pre>
3245 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-59" ></span>
3246 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
3247
3248
3249 OTHER indicates function is not supported
3250 Note that these values are incremented by one compared to
3251 the standard DECnet values."
3252 ::= { phivNonBroadcastEntry 2 }
3253
3254 phivNonBroadcastDuplex OBJECT-TYPE
3255 SYNTAX INTEGER {
3256 full (1),
3257 half (2)
3258 }
3259 ACCESS read-only
3260 STATUS mandatory
3261 DESCRIPTION
3262 "This value represents the Physical Link hardware
3263 duplex mode of the line device. The possible modes
3264 are:
3265
3266 FULL Full-duplex
3267 HALF Half-duplex
3268
3269 Note that these values are incremented by one compared to
3270 the standard DECnet values."
3271 ::= { phivNonBroadcastEntry 3 }
3272
3273 phivNonBroadcastClock OBJECT-TYPE
3274 SYNTAX INTEGER {
3275 external (1),
3276 internal (2),
3277 other (3)
3278 }
3279 ACCESS read-only
3280 STATUS mandatory
3281 DESCRIPTION
3282 "This value represents the Physical Link hardware clock
3283 mode for the line device. The values for clock-mode are:
3284
3285 INTERNAL For software controllable loopback use of
3286 the clock. On those devices that can support this
3287 mode, it causes the device to supply a clock signal
3288 such that a transmitted messages can be looped
3289 back from outside the device. This may require manual
3290 intervention other than the setting of this parameter
3291 value. For example, the operator may have to connect
3292 a loopback plug in place of the normal line.
3293
3294 EXTERNAL For normal clock operating mode, where the
3295 clock signal is supplied externally to the controller.
3296 Note that these values are incremented by one compared to
3297
3298
3299
3300 <span class="grey">DECnet Phase IV MIB Working Group [Page 59]</span></pre>
3301 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-60" ></span>
3302 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
3303
3304
3305 the standard DECnet values."
3306 ::= { phivNonBroadcastEntry 4 }
3307
3308 phivNonBroadcastRetransmitTimer OBJECT-TYPE
3309 SYNTAX INTEGER (1..65535)
3310 ACCESS read-only
3311 STATUS mandatory
3312 DESCRIPTION
3313 "This value represents number of milliseconds before
3314 the Data Link retransmits a block on the line. On
3315 half-duplex lines, this parameter is the select timer."
3316 DEFVAL { 3000 }
3317 ::= { phivNonBroadcastEntry 5 }
3318
3319 -- Area Parameters Group
3320
3321 -- The implementation of the Area Parameters Group is mandatory
3322 -- for all systems which implement level 2 routing.
3323
3324 phivAreaTable OBJECT-TYPE
3325 SYNTAX SEQUENCE OF PhivAreaEntry
3326 ACCESS not-accessible
3327 STATUS mandatory
3328 DESCRIPTION
3329 "Table of information kept on all areas known to
3330 this unit."
3331 ::= { area 1 }
3332
3333 phivAreaEntry OBJECT-TYPE
3334 SYNTAX PhivAreaEntry
3335 ACCESS not-accessible
3336 STATUS mandatory
3337 DESCRIPTION
3338 "The area routing information."
3339 INDEX { phivAreaNum }
3340 ::= { phivAreaTable 1 }
3341
3342 PhivAreaEntry ::=
3343 SEQUENCE {
3344 phivAreaNum
3345 INTEGER,
3346 phivAreaState
3347 INTEGER,
3348 phivAreaCost
3349 Gauge,
3350 phivAreaHops
3351 INTEGER,
3352 phivAreaNextNode
3353
3354
3355
3356 <span class="grey">DECnet Phase IV MIB Working Group [Page 60]</span></pre>
3357 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-61" ></span>
3358 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
3359
3360
3361 PhivAddr,
3362 phivAreaCircuitIndex
3363 INTEGER
3364 }
3365 phivAreaNum OBJECT-TYPE
3366 SYNTAX INTEGER (0..64)
3367 ACCESS read-only
3368 STATUS mandatory
3369 DESCRIPTION
3370 "This value indicates the area number of this entry."
3371 ::= { phivAreaEntry 1 }
3372
3373 phivAreaState OBJECT-TYPE
3374 SYNTAX INTEGER {
3375 reachable (4),
3376 unreachable (5)
3377 }
3378 ACCESS read-only
3379 STATUS mandatory
3380 DESCRIPTION
3381 "This value indicates the state of the area"
3382 ::= { phivAreaEntry 2 }
3383
3384 phivAreaCost OBJECT-TYPE
3385 SYNTAX Gauge
3386 ACCESS read-only
3387 STATUS mandatory
3388 DESCRIPTION
3389 "The total cost over the current path to the
3390 destination area. Cost is a value associated with
3391 using a circuit. Routing routes messages (data)
3392 along the path between 2 areas with the smallest
3393 cost."
3394 ::= { phivAreaEntry 3 }
3395
3396 phivAreaHops OBJECT-TYPE
3397 SYNTAX INTEGER (0..255)
3398 ACCESS read-only
3399 STATUS mandatory
3400 DESCRIPTION
3401 "The number of hops to a destination area. A hop is
3402 the routing value representing the logical distance
3403 between two areas in network."
3404 ::= { phivAreaEntry 4 }
3405
3406 phivAreaNextNode OBJECT-TYPE
3407 SYNTAX PhivAddr
3408 ACCESS read-only
3409
3410
3411
3412 <span class="grey">DECnet Phase IV MIB Working Group [Page 61]</span></pre>
3413 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-62" ></span>
3414 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
3415
3416
3417 STATUS mandatory
3418 DESCRIPTION
3419 "The next node on the circuit used to get to the
3420 area under scrutiny."
3421 ::= { phivAreaEntry 5 }
3422
3423 phivAreaCircuitIndex OBJECT-TYPE
3424 SYNTAX INTEGER
3425 ACCESS read-only
3426 STATUS mandatory
3427 DESCRIPTION
3428 "A unique index value for each known circuit."
3429 ::= { phivAreaEntry 6 }
3430
3431 -- Additional Area Parameters
3432
3433 phivAreaMaxCost OBJECT-TYPE
3434 SYNTAX INTEGER (1..1022)
3435 ACCESS read-write
3436 STATUS mandatory
3437 DESCRIPTION
3438 "This value represents the maximum total path cost
3439 allowed from the executor to any other level 2 routing
3440 node. The AREA MAXIMUM COST number is decimal in the
3441 range 1-1022. This parameter is only applicable if
3442 the executor node is of type AREA."
3443 ::= { area 2 }
3444
3445 phivAreaMaxHops OBJECT-TYPE
3446 SYNTAX INTEGER (1..30)
3447 ACCESS read-write
3448 STATUS mandatory
3449 DESCRIPTION
3450 "This value represents the maximum number of routing hops
3451 allowable from the executor to any other level 2
3452 routing node. This parameter is only applicable if the
3453 executor node is of type AREA."
3454 ::= { area 3 }
3455
3456 phivRouteMaxArea OBJECT-TYPE
3457 SYNTAX INTEGER (1..63)
3458 ACCESS read-write
3459 STATUS mandatory
3460 DESCRIPTION
3461 "This value represents the largest area number and,
3462 therefore, number of areas that can be known about
3463 by the executor node's Routing. This parameter is only
3464 applicable if the executor node is of type AREA."
3465
3466
3467
3468 <span class="grey">DECnet Phase IV MIB Working Group [Page 62]</span></pre>
3469 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-63" ></span>
3470 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
3471
3472
3473 ::= { area 4 }
3474
3475 END
3476
3477 <span class="h2"><a class="selflink" id="section-5" href="#section-5">5</a>. Acknowledgements</span>
3478
3479 This document is the result of work undertaken the by DECnet Phase IV
3480 MIB working group. In addition, the special contributions and
3481 comments of the following members are also acknowledged:
3482
3483 Chris Chiotasso, Sparticus
3484 Steven Hunter, National Energy Research Supercomputer Center,
3485 Lawrence Livermore National Laboratory
3486
3487 <span class="h2"><a class="selflink" id="section-6" href="#section-6">6</a>. References</span>
3488
3489 Cerf, V., "IAB Recommendations for the Development of Internet
3490 Network Management Standards", <a href="./rfc1052">RFC 1052</a>, NRI, April 1988.
3491
3492 Rose M., and K. McCloghrie, "Structure and Identification of
3493 Management Information for TCP/IP-based internets", <a href="./rfc1155">RFC 1155</a>,
3494 Performance Systems International, Hughes LAN Systems, May 1990.
3495
3496 McCloghrie K., and M. Rose, "Management Information Base for Network
3497 Management of TCP/IP-based internets", <a href="./rfc1156">RFC 1156</a>, Hughes LAN Systems,
3498 Performance Systems International, May 1990.
3499
3500 Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network
3501 Management Protocol", <a href="./rfc1157">RFC 1157</a>, SNMP Research, Performance Systems
3502 International, Performance Systems International, MIT Laboratory for
3503 Computer Science, May 1990.
3504
3505 McCloghrie K., and M. Rose, Editors, "Management Information Base for
3506 Network Management of TCP/IP-based internets", <a href="./rfc1213">RFC 1213</a>, Performance
3507 Systems International, March 1991.
3508
3509 Rose, M., and K. McCloghrie, Editors, "Concise MIB Definitions", <a href="./rfc1212">RFC</a>
3510 <a href="./rfc1212">1212</a>, Performance Systems International, Hughes LAN Systems, March
3511 1991.
3512
3513 Cook, J., Editor, "Definitions of Managed Objects for the Ethernet-
3514 like Interface Types", <a href="./rfc1284">RFC 1284</a>, Chipcom Corporation, December 1991.
3515
3516 Digital Equipment Corporation, "DECnet-ULTRIX NCP Command Reference",
3517 Digital Equipment Corporation, Maynard, Massachusetts.
3518
3519 Digital Equipment Corporation, "DECnet-ULTRIX USE Guide", Digital
3520 Equipment Corporation, Maynard, Massachusetts.
3521
3522
3523
3524 <span class="grey">DECnet Phase IV MIB Working Group [Page 63]</span></pre>
3525 <hr class='noprint'/><!--NewPage--><pre class='newpage'><span id="page-64" ></span>
3526 <span class="grey"><a href="./rfc1289">RFC 1289</a> DECnet Phase IV MIB December 1991</span>
3527
3528
3529 Digital Equipment Corporation, "DECnet DIGITAL Network Architecture,
3530 Network Management Functional Specification", Version 4.0.0. Digital
3531 Equipment Corporation, Maynard, Massachusetts, July 1983.
3532
3533 Digital Equipment Corporation, "DECnet DIGITAL Network Architecture,
3534 Routing Layer Functional Specification", Version 2.0.0. Digital
3535 Equipment Corporation, Maynard, Massachusetts, May 1983.
3536
3537 Security Considerations
3538
3539 Security issues are not discussed in this memo.
3540
3541 Author's Address
3542
3543 Jon Saperia
3544 Digital Equipment Corporation
3545 40 Old Bolton Road
3546 Stow, Massachusetts 01775-1215
3547
3548 Phone: 508-496-8333
3549
3550 EMail: [email protected]
3551
3552
3553
3554
3555
3556
3557
3558
3559
3560
3561
3562
3563
3564
3565
3566
3567
3568
3569
3570
3571
3572
3573
3574
3575
3576
3577
3578
3579
3580 DECnet Phase IV MIB Working Group [Page 64]
3581 </pre>