Debian Codegraph @

arch/arm/boot/dts/ti/omap/omap4-panda-common.dtsi

raw
1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Copyright (C) 2011-2013 Texas Instruments Incorporated - https://www.ti.com/
4 */
5 #include <dt-bindings/input/input.h>
6 #include "elpida_ecb240abacn.dtsi"
7 #include "omap4-mcpdm.dtsi"
8
9 / {
10 memory@80000000 {
11 device_type = "memory";
12 reg = <0x80000000 0x40000000>; /* 1 GB */
13 };
14
15 reserved-memory {
16 #address-cells = <1>;
17 #size-cells = <1>;
18 ranges;
19
20 dsp_memory_region: dsp-memory@98000000 {
21 compatible = "shared-dma-pool";
22 reg = <0x98000000 0x800000>;
23 reusable;
24 status = "okay";
25 };
26
27 ipu_memory_region: ipu-memory@98800000 {
28 compatible = "shared-dma-pool";
29 reg = <0x98800000 0x7000000>;
30 reusable;
31 status = "okay";
32 };
33 };
34
35 chosen {
36 stdout-path = &uart3;
37 };
38
39 aliases {
40 display0 = &dvi0;
41 display1 = &hdmi0;
42 ethernet = &ethernet;
43 };
44
45 leds: leds {
46 compatible = "gpio-leds";
47 pinctrl-names = "default";
48 pinctrl-0 = <
49 &led_wkgpio_pins
50 >;
51
52 led-heartbeat {
53 label = "pandaboard::status1";
54 gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
55 linux,default-trigger = "heartbeat";
56 };
57
58 led-mmc {
59 label = "pandaboard::status2";
60 gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
61 linux,default-trigger = "mmc0";
62 };
63 };
64
65 gpio_keys: gpio_keys {
66 compatible = "gpio-keys";
67 pinctrl-names = "default";
68 pinctrl-0 = <
69 &button_pins
70 >;
71
72 buttonS2 {
73 label = "button S2";
74 gpios = <&gpio4 25 GPIO_ACTIVE_LOW>; /* gpio_121 */
75 linux,code = <BTN_0>;
76 wakeup-source;
77 };
78 };
79
80 sound: sound {
81 compatible = "ti,abe-twl6040";
82 ti,model = "PandaBoard";
83
84 ti,mclk-freq = <38400000>;
85
86 ti,mcpdm = <&mcpdm>;
87
88 ti,twl6040 = <&twl6040>;
89
90 /* Audio routing */
91 ti,audio-routing =
92 "Headset Stereophone", "HSOL",
93 "Headset Stereophone", "HSOR",
94 "Ext Spk", "HFL",
95 "Ext Spk", "HFR",
96 "Line Out", "AUXL",
97 "Line Out", "AUXR",
98 "HSMIC", "Headset Mic",
99 "Headset Mic", "Headset Mic Bias",
100 "AFML", "Line In",
101 "AFMR", "Line In";
102 };
103
104 /* HS USB Port 1 Power */
105 hsusb1_power: hsusb1_power_reg {
106 compatible = "regulator-fixed";
107 regulator-name = "hsusb1_vbus";
108 regulator-min-microvolt = <3300000>;
109 regulator-max-microvolt = <3300000>;
110 gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; /* gpio_1 */
111 startup-delay-us = <70000>;
112 enable-active-high;
113 /*
114 * boot-on is required along with always-on as the
115 * regulator framework doesn't enable the regulator
116 * if boot-on is not there.
117 */
118 regulator-always-on;
119 regulator-boot-on;
120 };
121
122 /* HS USB Host PHY on PORT 1 */
123 hsusb1_phy: hsusb1_phy {
124 compatible = "usb-nop-xceiv";
125 reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; /* gpio_62 */
126 #phy-cells = <0>;
127 vcc-supply = <&hsusb1_power>;
128 clocks = <&auxclk3_ck>;
129 clock-names = "main_clk";
130 clock-frequency = <19200000>;
131 };
132
133 wl12xx_pwrseq: wl12xx-pwrseq {
134 compatible = "mmc-pwrseq-simple";
135 clocks = <&twl 0>;
136 clock-names = "ext_clock";
137 };
138
139 /* regulator for wl12xx on sdio5 */
140 wl12xx_vmmc: wl12xx_vmmc {
141 pinctrl-names = "default";
142 pinctrl-0 = <&wl12xx_gpio>;
143 compatible = "regulator-fixed";
144 regulator-name = "vwl1271";
145 regulator-min-microvolt = <1800000>;
146 regulator-max-microvolt = <1800000>;
147 gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
148 startup-delay-us = <70000>;
149 enable-active-high;
150 };
151
152 tfp410: encoder0 {
153 compatible = "ti,tfp410";
154 powerdown-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* gpio_0 */
155
156 ports {
157 #address-cells = <1>;
158 #size-cells = <0>;
159
160 port@0 {
161 reg = <0>;
162
163 tfp410_in: endpoint {
164 remote-endpoint = <&dpi_out>;
165 };
166 };
167
168 port@1 {
169 reg = <1>;
170
171 tfp410_out: endpoint {
172 remote-endpoint = <&dvi_connector_in>;
173 };
174 };
175 };
176 };
177
178 dvi0: connector0 {
179 compatible = "dvi-connector";
180 label = "dvi";
181
182 digital;
183
184 ddc-i2c-bus = <&i2c3>;
185
186 port {
187 dvi_connector_in: endpoint {
188 remote-endpoint = <&tfp410_out>;
189 };
190 };
191 };
192
193 tpd12s015: encoder1 {
194 compatible = "ti,tpd12s015";
195
196 gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
197 <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
198 <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
199
200 ports {
201 #address-cells = <1>;
202 #size-cells = <0>;
203
204 port@0 {
205 reg = <0>;
206
207 tpd12s015_in: endpoint {
208 remote-endpoint = <&hdmi_out>;
209 };
210 };
211
212 port@1 {
213 reg = <1>;
214
215 tpd12s015_out: endpoint {
216 remote-endpoint = <&hdmi_connector_in>;
217 };
218 };
219 };
220 };
221
222 hdmi0: connector1 {
223 compatible = "hdmi-connector";
224 label = "hdmi";
225
226 type = "a";
227
228 port {
229 hdmi_connector_in: endpoint {
230 remote-endpoint = <&tpd12s015_out>;
231 };
232 };
233 };
234 };
235
236 &omap4_pmx_core {
237 pinctrl-names = "default";
238 pinctrl-0 = <
239 &dss_dpi_pins
240 &tfp410_pins
241 &dss_hdmi_pins
242 &tpd12s015_pins
243 &hsusbb1_pins
244 >;
245
246 twl6040_pins: twl6040-pins {
247 pinctrl-single,pins = <
248 OMAP4_IOPAD(0x120, PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */
249 OMAP4_IOPAD(0x1a0, PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */
250 >;
251 };
252
253 mcbsp1_pins: mcbsp1-pins {
254 pinctrl-single,pins = <
255 OMAP4_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */
256 OMAP4_IOPAD(0x100, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */
257 OMAP4_IOPAD(0x102, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */
258 OMAP4_IOPAD(0x104, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */
259 >;
260 };
261
262 dss_dpi_pins: dss-dpi-pins {
263 pinctrl-single,pins = <
264 OMAP4_IOPAD(0x162, PIN_OUTPUT | MUX_MODE5) /* dispc2_data23 */
265 OMAP4_IOPAD(0x164, PIN_OUTPUT | MUX_MODE5) /* dispc2_data22 */
266 OMAP4_IOPAD(0x166, PIN_OUTPUT | MUX_MODE5) /* dispc2_data21 */
267 OMAP4_IOPAD(0x168, PIN_OUTPUT | MUX_MODE5) /* dispc2_data20 */
268 OMAP4_IOPAD(0x16a, PIN_OUTPUT | MUX_MODE5) /* dispc2_data19 */
269 OMAP4_IOPAD(0x16c, PIN_OUTPUT | MUX_MODE5) /* dispc2_data18 */
270 OMAP4_IOPAD(0x16e, PIN_OUTPUT | MUX_MODE5) /* dispc2_data15 */
271 OMAP4_IOPAD(0x170, PIN_OUTPUT | MUX_MODE5) /* dispc2_data14 */
272 OMAP4_IOPAD(0x172, PIN_OUTPUT | MUX_MODE5) /* dispc2_data13 */
273 OMAP4_IOPAD(0x174, PIN_OUTPUT | MUX_MODE5) /* dispc2_data12 */
274 OMAP4_IOPAD(0x176, PIN_OUTPUT | MUX_MODE5) /* dispc2_data11 */
275
276 OMAP4_IOPAD(0x1b4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data10 */
277 OMAP4_IOPAD(0x1b6, PIN_OUTPUT | MUX_MODE5) /* dispc2_data9 */
278 OMAP4_IOPAD(0x1b8, PIN_OUTPUT | MUX_MODE5) /* dispc2_data16 */
279 OMAP4_IOPAD(0x1ba, PIN_OUTPUT | MUX_MODE5) /* dispc2_data17 */
280 OMAP4_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE5) /* dispc2_hsync */
281 OMAP4_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE5) /* dispc2_pclk */
282 OMAP4_IOPAD(0x1c0, PIN_OUTPUT | MUX_MODE5) /* dispc2_vsync */
283 OMAP4_IOPAD(0x1c2, PIN_OUTPUT | MUX_MODE5) /* dispc2_de */
284 OMAP4_IOPAD(0x1c4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data8 */
285 OMAP4_IOPAD(0x1c6, PIN_OUTPUT | MUX_MODE5) /* dispc2_data7 */
286 OMAP4_IOPAD(0x1c8, PIN_OUTPUT | MUX_MODE5) /* dispc2_data6 */
287 OMAP4_IOPAD(0x1ca, PIN_OUTPUT | MUX_MODE5) /* dispc2_data5 */
288 OMAP4_IOPAD(0x1cc, PIN_OUTPUT | MUX_MODE5) /* dispc2_data4 */
289 OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE5) /* dispc2_data3 */
290
291 OMAP4_IOPAD(0x1d0, PIN_OUTPUT | MUX_MODE5) /* dispc2_data2 */
292 OMAP4_IOPAD(0x1d2, PIN_OUTPUT | MUX_MODE5) /* dispc2_data1 */
293 OMAP4_IOPAD(0x1d4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data0 */
294 >;
295 };
296
297 tfp410_pins: tfp410-pins {
298 pinctrl-single,pins = <
299 OMAP4_IOPAD(0x184, PIN_OUTPUT | MUX_MODE3) /* gpio_0 */
300 >;
301 };
302
303 dss_hdmi_pins: dss-hdmi-pins {
304 pinctrl-single,pins = <
305 OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
306 OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
307 OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
308 >;
309 };
310
311 tpd12s015_pins: tpd12s015-pins {
312 pinctrl-single,pins = <
313 OMAP4_IOPAD(0x062, PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */
314 OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */
315 OMAP4_IOPAD(0x098, PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */
316 >;
317 };
318
319 hsusbb1_pins: hsusbb1-pins {
320 pinctrl-single,pins = <
321 OMAP4_IOPAD(0x0c2, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */
322 OMAP4_IOPAD(0x0c4, PIN_OUTPUT | MUX_MODE4) /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */
323 OMAP4_IOPAD(0x0c6, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */
324 OMAP4_IOPAD(0x0c8, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */
325 OMAP4_IOPAD(0x0ca, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */
326 OMAP4_IOPAD(0x0cc, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */
327 OMAP4_IOPAD(0x0ce, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */
328 OMAP4_IOPAD(0x0d0, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */
329 OMAP4_IOPAD(0x0d2, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */
330 OMAP4_IOPAD(0x0d4, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */
331 OMAP4_IOPAD(0x0d6, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */
332 OMAP4_IOPAD(0x0d8, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */
333 >;
334 };
335
336 i2c1_pins: i2c1-pins {
337 pinctrl-single,pins = <
338 OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
339 OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
340 >;
341 };
342
343 i2c2_pins: i2c2-pins {
344 pinctrl-single,pins = <
345 OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */
346 OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */
347 >;
348 };
349
350 i2c3_pins: i2c3-pins {
351 pinctrl-single,pins = <
352 OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
353 OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
354 >;
355 };
356
357 i2c4_pins: i2c4-pins {
358 pinctrl-single,pins = <
359 OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */
360 OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
361 >;
362 };
363
364 /*
365 * wl12xx GPIO outputs for WLAN_EN, BT_EN, FM_EN, BT_WAKEUP
366 * REVISIT: Are the pull-ups needed for GPIO 48 and 49?
367 */
368 wl12xx_gpio: wl12xx-gpio-pins {
369 pinctrl-single,pins = <
370 OMAP4_IOPAD(0x066, PIN_OUTPUT | MUX_MODE3) /* gpmc_a19.gpio_43 - WLAN_EN */
371 OMAP4_IOPAD(0x070, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a24.gpio_48 */
372 >;
373 };
374
375 /* wl12xx GPIO inputs and SDIO pins */
376 wl12xx_pins: wl12xx-pins {
377 pinctrl-single,pins = <
378 OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3) /* gpmc_ncs2.gpio_52 */
379 OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */
380 OMAP4_IOPAD(0x148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */
381 OMAP4_IOPAD(0x14a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */
382 OMAP4_IOPAD(0x14c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */
383 OMAP4_IOPAD(0x14e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */
384 OMAP4_IOPAD(0x150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */
385 OMAP4_IOPAD(0x152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */
386 >;
387 };
388
389 button_pins: button-pins {
390 pinctrl-single,pins = <
391 OMAP4_IOPAD(0x114, PIN_INPUT_PULLUP | MUX_MODE3) /* gpio_121 */
392 >;
393 };
394
395 bt_pins: bt-pins {
396 pinctrl-single,pins = <
397 OMAP4_IOPAD(0x06c, PIN_OUTPUT | MUX_MODE3) /* gpmc_a22.gpio_46 - BTEN */
398 OMAP4_IOPAD(0x072, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a25.gpio_49 - BTWAKEUP */
399 >;
400 };
401
402 uart2_pins: uart2-pins {
403 pinctrl-single,pins = <
404 OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts.uart2_cts - HCI */
405 OMAP4_IOPAD(0x11a, PIN_OUTPUT | MUX_MODE0) /* uart2_rts.uart2_rts */
406 OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_rx.uart2_rx */
407 OMAP4_IOPAD(0x11e, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
408 >;
409 };
410 };
411
412 &omap4_pmx_wkup {
413 led_wkgpio_pins: leds-wkpins-pins {
414 pinctrl-single,pins = <
415 OMAP4_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */
416 OMAP4_IOPAD(0x05c, PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */
417 >;
418 };
419 };
420
421 &i2c1 {
422 pinctrl-names = "default";
423 pinctrl-0 = <&i2c1_pins>;
424
425 clock-frequency = <400000>;
426
427 twl: twl@48 {
428 reg = <0x48>;
429 /* IRQ# = 7 */
430 interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
431 #clock-cells = <1>;
432 system-power-controller;
433 };
434
435 twl6040: twl@4b {
436 compatible = "ti,twl6040";
437 #clock-cells = <0>;
438 reg = <0x4b>;
439
440 pinctrl-names = "default";
441 pinctrl-0 = <&twl6040_pins>;
442
443 /* IRQ# = 119 */
444 interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
445 ti,audpwron-gpio = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio line 127 */
446
447 vio-supply = <&v1v8>;
448 v2v1-supply = <&v2v1>;
449 enable-active-high;
450 };
451 };
452
453 #include "twl6030.dtsi"
454 #include "twl6030_omap4.dtsi"
455
456 &i2c2 {
457 pinctrl-names = "default";
458 pinctrl-0 = <&i2c2_pins>;
459
460 clock-frequency = <400000>;
461 };
462
463 &i2c3 {
464 pinctrl-names = "default";
465 pinctrl-0 = <&i2c3_pins>;
466
467 clock-frequency = <100000>;
468
469 /*
470 * Display monitor features are burnt in their EEPROM as EDID data.
471 * The EEPROM is connected as I2C slave device.
472 */
473 eeprom@50 {
474 compatible = "ti,eeprom";
475 reg = <0x50>;
476 };
477 };
478
479 &i2c4 {
480 pinctrl-names = "default";
481 pinctrl-0 = <&i2c4_pins>;
482
483 clock-frequency = <400000>;
484 };
485
486 &mmc1 {
487 vmmc-supply = <&vmmc>;
488 bus-width = <8>;
489 };
490
491 &mmc2 {
492 status = "disabled";
493 };
494
495 &mmc3 {
496 status = "disabled";
497 };
498
499 &mmc4 {
500 status = "disabled";
501 };
502
503 &mmc5 {
504 pinctrl-names = "default";
505 pinctrl-0 = <&wl12xx_pins>;
506 vmmc-supply = <&wl12xx_vmmc>;
507 interrupts-extended = <&wakeupgen GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH
508 &omap4_pmx_core 0x10e>;
509 non-removable;
510 bus-width = <4>;
511 cap-power-off-card;
512 mmc-pwrseq = <&wl12xx_pwrseq>;
513
514 #address-cells = <1>;
515 #size-cells = <0>;
516 wlcore: wlcore@2 {
517 compatible = "ti,wl1271";
518 reg = <2>;
519 /* gpio_53 with gpmc_ncs3 pad as wakeup */
520 interrupts-extended = <&gpio2 21 IRQ_TYPE_LEVEL_HIGH>,
521 <&omap4_pmx_core 0x3a>;
522 interrupt-names = "irq", "wakeup";
523 ref-clock-frequency = <38400000>;
524 };
525 };
526
527 &emif1 {
528 cs1-used;
529 device-handle = <&elpida_ECB240ABACN>;
530 };
531
532 &emif2 {
533 cs1-used;
534 device-handle = <&elpida_ECB240ABACN>;
535 };
536
537 &mcbsp1 {
538 pinctrl-names = "default";
539 pinctrl-0 = <&mcbsp1_pins>;
540 status = "okay";
541 };
542
543 &twl_usb_comparator {
544 usb-supply = <&vusb>;
545 };
546
547 &uart2 {
548 pinctrl-names = "default";
549 pinctrl-0 = <&uart2_pins>;
550 interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
551 &omap4_pmx_core OMAP4_UART2_RX>;
552
553 bluetooth {
554 compatible = "ti,wl1271-st";
555 pinctrl-names = "default";
556 pinctrl-0 = <&bt_pins>;
557 enable-gpios = <&gpio2 14 GPIO_ACTIVE_HIGH>; /* GPIO_46 */
558 clocks = <&twl 0>;
559 clock-names = "ext_clock";
560 };
561 };
562
563 &uart3 {
564 interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
565 &omap4_pmx_core OMAP4_UART3_RX>;
566 };
567
568 &uart4 {
569 interrupts-extended = <&wakeupgen GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH
570 &omap4_pmx_core OMAP4_UART4_RX>;
571 };
572
573 &usb_otg_hs {
574 interface-type = <1>;
575 mode = <3>;
576 power = <50>;
577 };
578
579 &usbhshost {
580 port1-mode = "ehci-phy";
581 };
582
583 &usbhsehci {
584 phys = <&hsusb1_phy>;
585
586 #address-cells = <1>;
587 #size-cells = <0>;
588
589 hub@1 {
590 compatible = "usb424,9514";
591 reg = <1>;
592 #address-cells = <1>;
593 #size-cells = <0>;
594
595 ethernet: ethernet@1 {
596 compatible = "usb424,ec00";
597 reg = <1>;
598 };
599 };
600 };
601
602 &dss {
603 status = "okay";
604
605 port {
606 dpi_out: endpoint {
607 remote-endpoint = <&tfp410_in>;
608 data-lines = <24>;
609 };
610 };
611 };
612
613 &dsi2 {
614 status = "okay";
615 vdd-supply = <&vcxio>;
616 };
617
618 &hdmi {
619 status = "okay";
620 vdda-supply = <&vdac>;
621
622 port {
623 hdmi_out: endpoint {
624 remote-endpoint = <&tpd12s015_in>;
625 };
626 };
627 };
628
629 &dsp {
630 status = "okay";
631 memory-region = <&dsp_memory_region>;
632 ti,timers = <&timer5>;
633 ti,watchdog-timers = <&timer6>;
634 };
635
636 &ipu {
637 status = "okay";
638 memory-region = <&ipu_memory_region>;
639 ti,timers = <&timer3>;
640 ti,watchdog-timers = <&timer9>, <&timer11>;
641 };