| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Device tree for Winterland IceBoard |
| 4 |
* |
| 5 |
* https://mcgillcosmology.com |
| 6 |
* https://threespeedlogic.com |
| 7 |
* |
| 8 |
* This is an ARM + FPGA instrumentation board used at telescopes in |
| 9 |
* Antarctica (the South Pole Telescope), Chile (POLARBEAR), and at the DRAO |
| 10 |
* observatory in British Columbia (CHIME). |
| 11 |
* |
| 12 |
* Copyright (c) 2019 Three-Speed Logic, Inc. <[email protected]> |
| 13 |
*/ |
| 14 |
|
| 15 |
/dts-v1/; |
| 16 |
|
| 17 |
#include "dm814x.dtsi" |
| 18 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 19 |
|
| 20 |
/ { |
| 21 |
model = "Winterland IceBoard"; |
| 22 |
compatible = "ti,dm8148", "ti,dm814"; |
| 23 |
|
| 24 |
chosen { |
| 25 |
stdout-path = "serial1:115200n8"; |
| 26 |
bootargs = "earlycon"; |
| 27 |
}; |
| 28 |
|
| 29 |
memory@80000000 { |
| 30 |
device_type = "memory"; |
| 31 |
reg = <0x80000000 0x40000000>; /* 1 GB */ |
| 32 |
}; |
| 33 |
|
| 34 |
vmmcsd_fixed: fixedregulator0 { |
| 35 |
compatible = "regulator-fixed"; |
| 36 |
regulator-name = "vmmcsd_fixed"; |
| 37 |
regulator-min-microvolt = <3300000>; |
| 38 |
regulator-max-microvolt = <3300000>; |
| 39 |
regulator-always-on; |
| 40 |
}; |
| 41 |
}; |
| 42 |
|
| 43 |
/* The MAC provides internal delay for the transmit path ONLY, which is enabled |
| 44 |
* provided no -id/-txid/-rxid suffix is provided to "phy-mode". |
| 45 |
* |
| 46 |
* The receive path is delayed at the PHY. The recommended register settings |
| 47 |
* are 0xf0 for the control bits, and 0x7777 for the data bits. However, the |
| 48 |
* conversion code in the kernel lies: the PHY's registers are 120 ps per tap, |
| 49 |
* and the kernel assumes 200 ps per tap. So we have fudged the numbers here to |
| 50 |
* obtain the correct register settings. |
| 51 |
*/ |
| 52 |
&mac { dual_emac = <1>; }; |
| 53 |
&cpsw_emac0 { |
| 54 |
phy-handle = <ðphy0>; |
| 55 |
phy-mode = "rgmii"; |
| 56 |
dual_emac_res_vlan = <1>; |
| 57 |
}; |
| 58 |
&cpsw_emac1 { |
| 59 |
phy-handle = <ðphy1>; |
| 60 |
phy-mode = "rgmii"; |
| 61 |
dual_emac_res_vlan = <2>; |
| 62 |
}; |
| 63 |
|
| 64 |
&davinci_mdio { |
| 65 |
ethphy0: ethernet-phy@0 { |
| 66 |
reg = <0x2>; |
| 67 |
|
| 68 |
rxc-skew-ps = <3000>; |
| 69 |
rxdv-skew-ps = <0>; |
| 70 |
|
| 71 |
rxd3-skew-ps = <0>; |
| 72 |
rxd2-skew-ps = <0>; |
| 73 |
rxd1-skew-ps = <0>; |
| 74 |
rxd0-skew-ps = <0>; |
| 75 |
|
| 76 |
phy-reset-gpios = <&gpio2 8 GPIO_ACTIVE_LOW>; |
| 77 |
}; |
| 78 |
|
| 79 |
ethphy1: ethernet-phy@1 { |
| 80 |
reg = <0x1>; |
| 81 |
|
| 82 |
rxc-skew-ps = <3000>; |
| 83 |
rxdv-skew-ps = <0>; |
| 84 |
|
| 85 |
rxd3-skew-ps = <0>; |
| 86 |
rxd2-skew-ps = <0>; |
| 87 |
rxd1-skew-ps = <0>; |
| 88 |
rxd0-skew-ps = <0>; |
| 89 |
|
| 90 |
phy-reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; |
| 91 |
}; |
| 92 |
}; |
| 93 |
|
| 94 |
&mmc1 { status = "disabled"; }; |
| 95 |
&mmc2 { |
| 96 |
pinctrl-names = "default"; |
| 97 |
pinctrl-0 = <&mmc2_pins>; |
| 98 |
vmmc-supply = <&vmmcsd_fixed>; |
| 99 |
bus-width = <4>; |
| 100 |
}; |
| 101 |
&mmc3 { status = "disabled"; }; |
| 102 |
|
| 103 |
&i2c1 { |
| 104 |
/* Most I2C activity happens through this port, with the sole exception |
| 105 |
* of the backplane. Since there are multiply assigned addresses, the |
| 106 |
* "i2c-mux-idle-disconnect" is important. |
| 107 |
*/ |
| 108 |
|
| 109 |
i2c-mux@70 { |
| 110 |
compatible = "nxp,pca9548"; |
| 111 |
reg = <0x70>; |
| 112 |
#address-cells = <1>; |
| 113 |
#size-cells = <0>; |
| 114 |
i2c-mux-idle-disconnect; |
| 115 |
|
| 116 |
i2c@0 { |
| 117 |
/* FMC A */ |
| 118 |
#address-cells = <1>; |
| 119 |
#size-cells = <0>; |
| 120 |
reg = <0>; |
| 121 |
}; |
| 122 |
|
| 123 |
i2c@1 { |
| 124 |
/* FMC B */ |
| 125 |
#address-cells = <1>; |
| 126 |
#size-cells = <0>; |
| 127 |
reg = <1>; |
| 128 |
}; |
| 129 |
|
| 130 |
i2c@2 { |
| 131 |
/* QSFP A */ |
| 132 |
#address-cells = <1>; |
| 133 |
#size-cells = <0>; |
| 134 |
reg = <2>; |
| 135 |
}; |
| 136 |
|
| 137 |
i2c@3 { |
| 138 |
/* QSFP B */ |
| 139 |
#address-cells = <1>; |
| 140 |
#size-cells = <0>; |
| 141 |
reg = <3>; |
| 142 |
}; |
| 143 |
|
| 144 |
i2c@4 { |
| 145 |
/* SFP */ |
| 146 |
#address-cells = <1>; |
| 147 |
#size-cells = <0>; |
| 148 |
reg = <4>; |
| 149 |
}; |
| 150 |
|
| 151 |
i2c@5 { |
| 152 |
#address-cells = <1>; |
| 153 |
#size-cells = <0>; |
| 154 |
reg = <5>; |
| 155 |
|
| 156 |
ina230@40 { compatible = "ti,ina230"; reg = <0x40>; shunt-resistor = <5000>; }; |
| 157 |
ina230@41 { compatible = "ti,ina230"; reg = <0x41>; shunt-resistor = <5000>; }; |
| 158 |
ina230@42 { compatible = "ti,ina230"; reg = <0x42>; shunt-resistor = <5000>; }; |
| 159 |
|
| 160 |
ina230@44 { compatible = "ti,ina230"; reg = <0x44>; shunt-resistor = <5000>; }; |
| 161 |
ina230@45 { compatible = "ti,ina230"; reg = <0x45>; shunt-resistor = <5000>; }; |
| 162 |
ina230@46 { compatible = "ti,ina230"; reg = <0x46>; shunt-resistor = <5000>; }; |
| 163 |
|
| 164 |
ina230@47 { compatible = "ti,ina230"; reg = <0x47>; shunt-resistor = <5500>; }; |
| 165 |
ina230@48 { compatible = "ti,ina230"; reg = <0x48>; shunt-resistor = <2360>; }; |
| 166 |
ina230@49 { compatible = "ti,ina230"; reg = <0x49>; shunt-resistor = <2360>; }; |
| 167 |
ina230@43 { compatible = "ti,ina230"; reg = <0x43>; shunt-resistor = <2360>; }; |
| 168 |
ina230@4b { compatible = "ti,ina230"; reg = <0x4b>; shunt-resistor = <5500>; }; |
| 169 |
ina230@4c { compatible = "ti,ina230"; reg = <0x4c>; shunt-resistor = <2360>; }; |
| 170 |
ina230@4d { compatible = "ti,ina230"; reg = <0x4d>; shunt-resistor = <770>; }; |
| 171 |
ina230@4e { compatible = "ti,ina230"; reg = <0x4e>; shunt-resistor = <770>; }; |
| 172 |
ina230@4f { compatible = "ti,ina230"; reg = <0x4f>; shunt-resistor = <770>; }; |
| 173 |
}; |
| 174 |
|
| 175 |
i2c@6 { |
| 176 |
/* Backplane */ |
| 177 |
#address-cells = <1>; |
| 178 |
#size-cells = <0>; |
| 179 |
reg = <6>; |
| 180 |
}; |
| 181 |
|
| 182 |
i2c@7 { |
| 183 |
#address-cells = <1>; |
| 184 |
#size-cells = <0>; |
| 185 |
reg = <7>; |
| 186 |
|
| 187 |
u41: pca9575@20 { |
| 188 |
compatible = "nxp,pca9575"; |
| 189 |
reg = <0x20>; |
| 190 |
gpio-controller; |
| 191 |
#gpio-cells = <2>; |
| 192 |
|
| 193 |
gpio-line-names = |
| 194 |
"FMCA_EN_12V0", "FMCA_EN_3V3", "FMCA_EN_VADJ", "FMCA_PG_M2C", |
| 195 |
"FMCA_PG_C2M", "FMCA_PRSNT_M2C_L", "FMCA_CLK_DIR", "SFP_LOS", |
| 196 |
"FMCB_EN_12V0", "FMCB_EN_3V3", "FMCB_EN_VADJ", "FMCB_PG_M2C", |
| 197 |
"FMCB_PG_C2M", "FMCB_PRSNT_M2C_L", "FMCB_CLK_DIR", "SFP_ModPrsL"; |
| 198 |
reset-gpios = <&gpio2 11 GPIO_ACTIVE_LOW>; |
| 199 |
}; |
| 200 |
|
| 201 |
u42: pca9575@21 { |
| 202 |
compatible = "nxp,pca9575"; |
| 203 |
reg = <0x21>; |
| 204 |
gpio-controller; |
| 205 |
#gpio-cells = <2>; |
| 206 |
gpio-line-names = |
| 207 |
"QSFPA_ModPrsL", "QSFPA_IntL", "QSFPA_ResetL", "QSFPA_ModSelL", |
| 208 |
"QSFPA_LPMode", "QSFPB_ModPrsL", "QSFPB_IntL", "QSFPB_ResetL", |
| 209 |
"SFP_TxFault", "SFP_TxDisable", "SFP_RS0", "SFP_RS1", |
| 210 |
"QSFPB_ModSelL", "QSFPB_LPMode", "SEL_SFP", "ARM_MR"; |
| 211 |
reset-gpios = <&gpio2 11 GPIO_ACTIVE_LOW>; |
| 212 |
}; |
| 213 |
|
| 214 |
u48: pca9575@22 { |
| 215 |
compatible = "nxp,pca9575"; |
| 216 |
reg = <0x22>; |
| 217 |
gpio-controller; |
| 218 |
#gpio-cells = <2>; |
| 219 |
|
| 220 |
sw-gpios = <&u48 0 0>, <&u48 1 0>, <&u48 2 0>, <&u48 3 0>, |
| 221 |
<&u48 4 0>, <&u48 5 0>, <&u48 6 0>, <&u48 7 0>; |
| 222 |
led-gpios = <&u48 7 0>, <&u48 6 0>, <&u48 5 0>, <&u48 4 0>, |
| 223 |
<&u48 3 0>, <&u48 2 0>, <&u48 1 0>, <&u48 0 0>; |
| 224 |
|
| 225 |
gpio-line-names = |
| 226 |
"GP_SW1", "GP_SW2", "GP_SW3", "GP_SW4", |
| 227 |
"GP_SW5", "GP_SW6", "GP_SW7", "GP_SW8", |
| 228 |
"GP_LED8", "GP_LED7", "GP_LED6", "GP_LED5", |
| 229 |
"GP_LED4", "GP_LED3", "GP_LED2", "GP_LED1"; |
| 230 |
reset-gpios = <&gpio2 11 GPIO_ACTIVE_LOW>; |
| 231 |
}; |
| 232 |
|
| 233 |
u59: pca9575@23 { |
| 234 |
compatible = "nxp,pca9575"; |
| 235 |
reg = <0x23>; |
| 236 |
gpio-controller; |
| 237 |
#gpio-cells = <2>; |
| 238 |
gpio-line-names = |
| 239 |
"GP_LED9", "GP_LED10", "GP_LED11", "GP_LED12", |
| 240 |
"GTX1V8PowerFault", "PHYAPowerFault", "PHYBPowerFault", "ArmPowerFault", |
| 241 |
"BP_SLOW_GPIO0", "BP_SLOW_GPIO1", "BP_SLOW_GPIO2", "BP_SLOW_GPIO3", |
| 242 |
"BP_SLOW_GPIO4", "BP_SLOW_GPIO5", "__unused_u59_p16", "__unused_u59_p17"; |
| 243 |
reset-gpios = <&gpio2 11 GPIO_ACTIVE_LOW>; |
| 244 |
}; |
| 245 |
|
| 246 |
tmp100@48 { compatible = "ti,tmp100"; reg = <0x48>; }; |
| 247 |
tmp100@4a { compatible = "ti,tmp100"; reg = <0x4a>; }; |
| 248 |
tmp100@4b { compatible = "ti,tmp100"; reg = <0x4b>; }; |
| 249 |
tmp100@4c { compatible = "ti,tmp100"; reg = <0x4c>; }; |
| 250 |
|
| 251 |
/* EEPROM bank and serial number are treated as separate devices */ |
| 252 |
eeprom@57 { compatible = "atmel,24c01"; reg = <0x57>; }; |
| 253 |
eeprom@5f { compatible = "atmel,24cs01"; reg = <0x5f>; }; |
| 254 |
}; |
| 255 |
}; |
| 256 |
}; |
| 257 |
|
| 258 |
&i2c2 { |
| 259 |
i2c-mux@71 { |
| 260 |
compatible = "nxp,pca9548"; |
| 261 |
reg = <0x71>; |
| 262 |
#address-cells = <1>; |
| 263 |
#size-cells = <0>; |
| 264 |
|
| 265 |
i2c@6 { |
| 266 |
/* Backplane */ |
| 267 |
#address-cells = <1>; |
| 268 |
#size-cells = <0>; |
| 269 |
reg = <6>; |
| 270 |
multi-master; |
| 271 |
|
| 272 |
/* All backplanes should have this -- it's how we know they're there. */ |
| 273 |
eeprom@54 { compatible="atmel,24c08"; reg=<0x54>; }; |
| 274 |
eeprom@5c { compatible="atmel,24cs08"; reg=<0x5c>; }; |
| 275 |
|
| 276 |
/* 16 slot backplane */ |
| 277 |
tmp421@4d { compatible="ti,tmp421"; reg=<0x4d>; }; |
| 278 |
tmp421@4e { compatible="ti,tmp421"; reg=<0x4e>; }; |
| 279 |
ina230@40 { compatible = "ti,ina230"; reg = <0x40>; shunt-resistor = <2360>; }; |
| 280 |
amc6821@18 { compatible = "ti,amc6821"; reg = <0x18>; }; |
| 281 |
|
| 282 |
/* Single slot backplane */ |
| 283 |
}; |
| 284 |
}; |
| 285 |
}; |
| 286 |
|
| 287 |
&pincntl { |
| 288 |
mmc2_pins: mmc2-pins { |
| 289 |
pinctrl-single,pins = < |
| 290 |
DM814X_IOPAD(0x0800, PIN_INPUT | 0x1) /* SD1_CLK */ |
| 291 |
DM814X_IOPAD(0x0804, PIN_INPUT_PULLUP | 0x1) /* SD1_CMD */ |
| 292 |
DM814X_IOPAD(0x0808, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[0] */ |
| 293 |
DM814X_IOPAD(0x080c, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[1] */ |
| 294 |
DM814X_IOPAD(0x0810, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[2] */ |
| 295 |
DM814X_IOPAD(0x0814, PIN_INPUT_PULLUP | 0x1) /* SD1_DAT[3] */ |
| 296 |
DM814X_IOPAD(0x0924, PIN_INPUT_PULLUP | 0x40) /* SD1_POW */ |
| 297 |
DM814X_IOPAD(0x0928, PIN_INPUT | 0x40) /* SD1_SDWP */ |
| 298 |
DM814X_IOPAD(0x093C, PIN_INPUT | 0x2) /* SD1_SDCD */ |
| 299 |
>; |
| 300 |
}; |
| 301 |
|
| 302 |
usb0_pins: usb0-pins { |
| 303 |
pinctrl-single,pins = < |
| 304 |
DM814X_IOPAD(0x0c34, PIN_OUTPUT | 0x1) /* USB0_DRVVBUS */ |
| 305 |
>; |
| 306 |
}; |
| 307 |
|
| 308 |
usb1_pins: usb1-pins { |
| 309 |
pinctrl-single,pins = < |
| 310 |
DM814X_IOPAD(0x0834, PIN_OUTPUT | 0x80) /* USB1_DRVVBUS */ |
| 311 |
>; |
| 312 |
}; |
| 313 |
|
| 314 |
gpio1_pins: gpio1-pins { |
| 315 |
pinctrl-single,pins = < |
| 316 |
DM814X_IOPAD(0x081c, PIN_OUTPUT | 0x80) /* PROGRAM_B */ |
| 317 |
DM814X_IOPAD(0x0820, PIN_INPUT | 0x80) /* INIT_B */ |
| 318 |
DM814X_IOPAD(0x0824, PIN_INPUT | 0x80) /* DONE */ |
| 319 |
|
| 320 |
DM814X_IOPAD(0x0838, PIN_INPUT_PULLUP | 0x80) /* FMCA_TMS */ |
| 321 |
DM814X_IOPAD(0x083c, PIN_INPUT_PULLUP | 0x80) /* FMCA_TCK */ |
| 322 |
DM814X_IOPAD(0x0898, PIN_INPUT_PULLUP | 0x80) /* FMCA_TDO */ |
| 323 |
DM814X_IOPAD(0x089c, PIN_INPUT_PULLUP | 0x80) /* FMCA_TDI */ |
| 324 |
DM814X_IOPAD(0x08ac, PIN_INPUT_PULLUP | 0x80) /* FMCA_TRST */ |
| 325 |
|
| 326 |
DM814X_IOPAD(0x08b0, PIN_INPUT_PULLUP | 0x80) /* FMCB_TMS */ |
| 327 |
DM814X_IOPAD(0x0a88, PIN_INPUT_PULLUP | 0x80) /* FMCB_TCK */ |
| 328 |
DM814X_IOPAD(0x0a8c, PIN_INPUT_PULLUP | 0x80) /* FMCB_TDO */ |
| 329 |
DM814X_IOPAD(0x08bc, PIN_INPUT_PULLUP | 0x80) /* FMCB_TDI */ |
| 330 |
DM814X_IOPAD(0x0a94, PIN_INPUT_PULLUP | 0x80) /* FMCB_TRST */ |
| 331 |
|
| 332 |
DM814X_IOPAD(0x08d4, PIN_INPUT_PULLUP | 0x80) /* FPGA_TMS */ |
| 333 |
DM814X_IOPAD(0x0aa8, PIN_INPUT_PULLUP | 0x80) /* FPGA_TCK */ |
| 334 |
DM814X_IOPAD(0x0adc, PIN_INPUT_PULLUP | 0x80) /* FPGA_TDO */ |
| 335 |
DM814X_IOPAD(0x0ab0, PIN_INPUT_PULLUP | 0x80) /* FPGA_TDI */ |
| 336 |
>; |
| 337 |
}; |
| 338 |
|
| 339 |
gpio2_pins: gpio2-pins { |
| 340 |
pinctrl-single,pins = < |
| 341 |
DM814X_IOPAD(0x090c, PIN_INPUT_PULLUP | 0x80) /* PHY A IRQ */ |
| 342 |
DM814X_IOPAD(0x0910, PIN_INPUT_PULLUP | 0x80) /* PHY A RESET */ |
| 343 |
DM814X_IOPAD(0x08f4, PIN_INPUT_PULLUP | 0x80) /* PHY B IRQ */ |
| 344 |
DM814X_IOPAD(0x08f8, PIN_INPUT_PULLUP | 0x80) /* PHY B RESET */ |
| 345 |
|
| 346 |
//DM814X_IOPAD(0x0a14, PIN_INPUT_PULLUP | 0x80) /* ARM IRQ */ |
| 347 |
//DM814X_IOPAD(0x0900, PIN_INPUT | 0x80) /* GPIO IRQ */ |
| 348 |
DM814X_IOPAD(0x0a2c, PIN_INPUT_PULLUP | 0x80) /* GPIO RESET */ |
| 349 |
>; |
| 350 |
}; |
| 351 |
|
| 352 |
gpio4_pins: gpio4-pins { |
| 353 |
pinctrl-single,pins = < |
| 354 |
/* The PLL doesn't react well to the SPI controller reset, so |
| 355 |
* we force the CS lines to pull up as GPIOs until we're ready. |
| 356 |
* See https://e2e.ti.com/support/processors/f/791/t/276011?Linux-support-for-AM3874-DM8148-in-Arago-linux-omap3 |
| 357 |
*/ |
| 358 |
DM814X_IOPAD(0x0b3c, PIN_INPUT_PULLUP | 0x80) /* BP_ARM_GPIO0 */ |
| 359 |
DM814X_IOPAD(0x0b40, PIN_INPUT_PULLUP | 0x80) /* BP_ARM_GPIO1 */ |
| 360 |
DM814X_IOPAD(0x0b44, PIN_INPUT_PULLUP | 0x80) /* BP_ARM_GPIO2 */ |
| 361 |
DM814X_IOPAD(0x0b48, PIN_INPUT_PULLUP | 0x80) /* BP_ARM_GPIO3 */ |
| 362 |
DM814X_IOPAD(0x0b4c, PIN_INPUT_PULLUP | 0x80) /* BP_ARM_GPIO4 */ |
| 363 |
DM814X_IOPAD(0x0b50, PIN_INPUT_PULLUP | 0x80) /* BP_ARM_GPIO5 */ |
| 364 |
>; |
| 365 |
}; |
| 366 |
|
| 367 |
spi2_pins: spi2-pins { |
| 368 |
pinctrl-single,pins = < |
| 369 |
DM814X_IOPAD(0x0950, PIN_INPUT_PULLUP | 0x80) /* PLL SPI CS1 as GPIO */ |
| 370 |
DM814X_IOPAD(0x0818, PIN_INPUT_PULLUP | 0x80) /* PLL SPI CS2 as GPIO */ |
| 371 |
>; |
| 372 |
}; |
| 373 |
|
| 374 |
spi4_pins: spi4-pins { |
| 375 |
pinctrl-single,pins = < |
| 376 |
DM814X_IOPAD(0x0a7c, 0x20) |
| 377 |
DM814X_IOPAD(0x0b74, 0x20) |
| 378 |
DM814X_IOPAD(0x0b78, PIN_OUTPUT | 0x20) |
| 379 |
DM814X_IOPAD(0x0b7c, PIN_OUTPUT_PULLDOWN | 0x20) |
| 380 |
DM814X_IOPAD(0x0b80, PIN_INPUT | 0x20) |
| 381 |
>; |
| 382 |
}; |
| 383 |
}; |
| 384 |
|
| 385 |
&gpio1 { |
| 386 |
pinctrl-names = "default"; |
| 387 |
pinctrl-0 = <&gpio1_pins>; |
| 388 |
gpio-line-names = |
| 389 |
"", "PROGRAM_B", "INIT_B", "DONE", /* 0-3 */ |
| 390 |
"", "", "", "", /* 4-7 */ |
| 391 |
"FMCA_TMS", "FMCA_TCK", "FMCA_TDO", "FMCA_TDI", /* 8-11 */ |
| 392 |
"", "", "", "FMCA_TRST", /* 12-15 */ |
| 393 |
"FMCB_TMS", "FMCB_TCK", "FMCB_TDO", "FMCB_TDI", /* 16-19 */ |
| 394 |
"FMCB_TRST", "", "", "", /* 20-23 */ |
| 395 |
"FPGA_TMS", "FPGA_TCK", "FPGA_TDO", "FPGA_TDI", /* 24-27 */ |
| 396 |
"", "", "", ""; /* 28-31 */ |
| 397 |
}; |
| 398 |
|
| 399 |
&gpio2 { |
| 400 |
pinctrl-names = "default"; |
| 401 |
pinctrl-0 = <&gpio2_pins>; |
| 402 |
gpio-line-names = |
| 403 |
"PHYA_IRQ_N", "PHYA_RESET_N", "", "", /* 0-3 */ |
| 404 |
"", "", "", "PHYB_IRQ_N", /* 4-7 */ |
| 405 |
"PHYB_RESET_N", "ARM_IRQ", "GPIO_IRQ", ""; /* 8-11 */ |
| 406 |
}; |
| 407 |
|
| 408 |
&gpio3 { |
| 409 |
pinctrl-names = "default"; |
| 410 |
/*pinctrl-0 = <&gpio3_pins>;*/ |
| 411 |
gpio-line-names = |
| 412 |
"", "", "ARMClkSel0", "", /* 0-3 */ |
| 413 |
"EnFPGARef", "", "", "ARMClkSel1"; /* 4-7 */ |
| 414 |
}; |
| 415 |
|
| 416 |
&gpio4 { |
| 417 |
pinctrl-names = "default"; |
| 418 |
pinctrl-0 = <&gpio4_pins>; |
| 419 |
gpio-line-names = |
| 420 |
"BP_ARM_GPIO0", "BP_ARM_GPIO1", "BP_ARM_GPIO2", "BP_ARM_GPIO3", |
| 421 |
"BP_ARM_GPIO4", "BP_ARM_GPIO5"; |
| 422 |
}; |
| 423 |
|
| 424 |
&usb0 { |
| 425 |
pinctrl-names = "default"; |
| 426 |
pinctrl-0 = <&usb0_pins>; |
| 427 |
dr_mode = "host"; |
| 428 |
}; |
| 429 |
|
| 430 |
&usb1 { |
| 431 |
pinctrl-names = "default"; |
| 432 |
pinctrl-0 = <&usb1_pins>; |
| 433 |
dr_mode = "host"; |
| 434 |
}; |
| 435 |
|
| 436 |
&mcspi1 { |
| 437 |
flash@0 { |
| 438 |
#address-cells = <1>; |
| 439 |
#size-cells = <1>; |
| 440 |
compatible = "jedec,spi-nor"; |
| 441 |
reg = <0>; |
| 442 |
spi-max-frequency = <40000000>; |
| 443 |
|
| 444 |
fsbl@0 { |
| 445 |
/* 256 kB */ |
| 446 |
label = "U-Boot-min"; |
| 447 |
reg = <0 0x40000>; |
| 448 |
}; |
| 449 |
ssbl@1 { |
| 450 |
/* 512 kB */ |
| 451 |
label = "U-Boot"; |
| 452 |
reg = <0x40000 0x80000>; |
| 453 |
}; |
| 454 |
bootenv@2 { |
| 455 |
/* 256 kB */ |
| 456 |
label = "U-Boot Env"; |
| 457 |
reg = <0xc0000 0x40000>; |
| 458 |
}; |
| 459 |
kernel@3 { |
| 460 |
/* 4 MB */ |
| 461 |
label = "Kernel"; |
| 462 |
reg = <0x100000 0x400000>; |
| 463 |
}; |
| 464 |
ipmi@4 { |
| 465 |
label = "IPMI FRU"; |
| 466 |
reg = <0x500000 0x40000>; |
| 467 |
}; |
| 468 |
fs@5 { |
| 469 |
label = "File System"; |
| 470 |
reg = <0x540000 0x1ac0000>; |
| 471 |
}; |
| 472 |
}; |
| 473 |
}; |
| 474 |
|
| 475 |
&mcspi3 { |
| 476 |
/* DMA event numbers stolen from MCASP */ |
| 477 |
dmas = <&edma_xbar 8 0 16 &edma_xbar 9 0 17 |
| 478 |
&edma_xbar 10 0 18 &edma_xbar 11 0 19>; |
| 479 |
dma-names = "tx0", "rx0", "tx1", "rx1"; |
| 480 |
}; |
| 481 |
|
| 482 |
&mcspi4 { |
| 483 |
pinctrl-names = "default"; |
| 484 |
pinctrl-0 = <&spi4_pins>; |
| 485 |
|
| 486 |
/* DMA event numbers stolen from MCASP, MCBSP */ |
| 487 |
dmas = <&edma_xbar 12 0 20 &edma_xbar 13 0 21>; |
| 488 |
dma-names = "tx0", "rx0"; |
| 489 |
}; |