| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Support for CompuLab CM-T3517 |
| 4 |
*/ |
| 5 |
/dts-v1/; |
| 6 |
|
| 7 |
#include "am3517.dtsi" |
| 8 |
#include "omap3-cm-t3x.dtsi" |
| 9 |
|
| 10 |
/ { |
| 11 |
model = "CompuLab CM-T3517"; |
| 12 |
compatible = "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3"; |
| 13 |
|
| 14 |
vmmc: regulator-vmmc { |
| 15 |
compatible = "regulator-fixed"; |
| 16 |
regulator-name = "vmmc"; |
| 17 |
regulator-min-microvolt = <3300000>; |
| 18 |
regulator-max-microvolt = <3300000>; |
| 19 |
}; |
| 20 |
|
| 21 |
wl12xx_vmmc2: wl12xx_vmmc2 { |
| 22 |
compatible = "regulator-fixed"; |
| 23 |
regulator-name = "vw1271"; |
| 24 |
pinctrl-names = "default"; |
| 25 |
pinctrl-0 = < |
| 26 |
&wl12xx_wkup_pins |
| 27 |
&wl12xx_core_pins |
| 28 |
>; |
| 29 |
regulator-min-microvolt = <1800000>; |
| 30 |
regulator-max-microvolt = <1800000>; |
| 31 |
gpio = <&gpio1 6 GPIO_ACTIVE_HIGH >; /* gpio6 */ |
| 32 |
startup-delay-us = <20000>; |
| 33 |
enable-active-high; |
| 34 |
}; |
| 35 |
|
| 36 |
wl12xx_vaux2: wl12xx_vaux2 { |
| 37 |
compatible = "regulator-fixed"; |
| 38 |
regulator-name = "vwl1271_vaux2"; |
| 39 |
regulator-min-microvolt = <1800000>; |
| 40 |
regulator-max-microvolt = <1800000>; |
| 41 |
}; |
| 42 |
}; |
| 43 |
|
| 44 |
&omap3_pmx_wkup { |
| 45 |
|
| 46 |
wl12xx_wkup_pins: wl12xx-wkup-pins { |
| 47 |
pinctrl-single,pins = < |
| 48 |
OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */ |
| 49 |
OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE4) /* sys_boot4.gpio_6 */ |
| 50 |
>; |
| 51 |
}; |
| 52 |
}; |
| 53 |
|
| 54 |
&omap3_pmx_core { |
| 55 |
|
| 56 |
phy1_reset_pins: hsusb1-phy-reset-pins { |
| 57 |
pinctrl-single,pins = < |
| 58 |
OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE4) /* uart2_tx.gpio_146 */ |
| 59 |
>; |
| 60 |
}; |
| 61 |
|
| 62 |
phy2_reset_pins: hsusb2-phy-reset-pins { |
| 63 |
pinctrl-single,pins = < |
| 64 |
OMAP3_CORE1_IOPAD(0x217a, PIN_OUTPUT | MUX_MODE4) /* uart2_rx.gpio_147 */ |
| 65 |
>; |
| 66 |
}; |
| 67 |
|
| 68 |
otg_drv_vbus: otg-drv-vbus-pins { |
| 69 |
pinctrl-single,pins = < |
| 70 |
OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50MHz_clk.usb0_drvvbus */ |
| 71 |
>; |
| 72 |
}; |
| 73 |
|
| 74 |
mmc2_pins: mmc2-pins { |
| 75 |
pinctrl-single,pins = < |
| 76 |
OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ |
| 77 |
OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ |
| 78 |
OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ |
| 79 |
OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ |
| 80 |
OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ |
| 81 |
OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ |
| 82 |
>; |
| 83 |
}; |
| 84 |
|
| 85 |
wl12xx_core_pins: wl12xx-core-pins { |
| 86 |
pinctrl-single,pins = < |
| 87 |
OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs5.gpio_56 */ |
| 88 |
OMAP3_CORE1_IOPAD(0x2176, PIN_INPUT_PULLUP | MUX_MODE4) /* uart2_rts.gpio_145 */ |
| 89 |
>; |
| 90 |
}; |
| 91 |
|
| 92 |
usb_hub_pins: usb-hub-pins { |
| 93 |
pinctrl-single,pins = < |
| 94 |
OMAP3_CORE1_IOPAD(0x2184, PIN_OUTPUT | MUX_MODE4) /* mcbsp4_clkx.gpio_152 - USB HUB RST */ |
| 95 |
>; |
| 96 |
}; |
| 97 |
}; |
| 98 |
|
| 99 |
&hsusb1_phy { |
| 100 |
pinctrl-names = "default"; |
| 101 |
pinctrl-0 = <&phy1_reset_pins>; |
| 102 |
reset-gpios = <&gpio5 18 GPIO_ACTIVE_LOW>; |
| 103 |
}; |
| 104 |
|
| 105 |
&hsusb2_phy { |
| 106 |
pinctrl-names = "default"; |
| 107 |
pinctrl-0 = <&phy2_reset_pins>; |
| 108 |
reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; |
| 109 |
}; |
| 110 |
|
| 111 |
&davinci_emac { |
| 112 |
status = "okay"; |
| 113 |
}; |
| 114 |
|
| 115 |
&davinci_mdio { |
| 116 |
status = "okay"; |
| 117 |
}; |
| 118 |
|
| 119 |
&am35x_otg_hs { |
| 120 |
status = "okay"; |
| 121 |
pinctrl-names = "default"; |
| 122 |
pinctrl-0 = <&otg_drv_vbus>; |
| 123 |
}; |
| 124 |
|
| 125 |
&mmc1 { |
| 126 |
vmmc-supply = <&vmmc>; |
| 127 |
}; |
| 128 |
|
| 129 |
&mmc2 { |
| 130 |
pinctrl-names = "default"; |
| 131 |
pinctrl-0 = <&mmc2_pins>; |
| 132 |
vmmc-supply = <&wl12xx_vmmc2>; |
| 133 |
vqmmc-supply = <&wl12xx_vaux2>; |
| 134 |
non-removable; |
| 135 |
bus-width = <4>; |
| 136 |
cap-power-off-card; |
| 137 |
|
| 138 |
#address-cells = <1>; |
| 139 |
#size-cells = <0>; |
| 140 |
wlcore: wlcore@2 { |
| 141 |
compatible = "ti,wl1271"; |
| 142 |
reg = <2>; |
| 143 |
interrupt-parent = <&gpio5>; |
| 144 |
interrupts = <17 IRQ_TYPE_EDGE_RISING>; /* gpio 145 */ |
| 145 |
ref-clock-frequency = <38400000>; |
| 146 |
}; |
| 147 |
}; |
| 148 |
|
| 149 |
&dss { |
| 150 |
status = "okay"; |
| 151 |
|
| 152 |
pinctrl-names = "default"; |
| 153 |
pinctrl-0 = < |
| 154 |
&dss_dpi_pins_common |
| 155 |
&dss_dpi_pins_cm_t35x |
| 156 |
>; |
| 157 |
}; |
| 158 |
|