| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Copyright (C) 2016 Texas Instruments Incorporated - https://www.ti.com/ |
| 4 |
*/ |
| 5 |
#include "dra72-evm-common.dtsi" |
| 6 |
#include "dra72x-mmc-iodelay.dtsi" |
| 7 |
#include <dt-bindings/net/ti-dp83867.h> |
| 8 |
|
| 9 |
/ { |
| 10 |
model = "TI DRA722 Rev C EVM"; |
| 11 |
|
| 12 |
memory@0 { |
| 13 |
device_type = "memory"; |
| 14 |
reg = <0x0 0x80000000 0x0 0x80000000>; /* 2GB */ |
| 15 |
}; |
| 16 |
|
| 17 |
reserved-memory { |
| 18 |
#address-cells = <2>; |
| 19 |
#size-cells = <2>; |
| 20 |
ranges; |
| 21 |
|
| 22 |
ipu2_cma_pool: ipu2_cma@95800000 { |
| 23 |
compatible = "shared-dma-pool"; |
| 24 |
reg = <0x0 0x95800000 0x0 0x3800000>; |
| 25 |
reusable; |
| 26 |
status = "okay"; |
| 27 |
}; |
| 28 |
|
| 29 |
dsp1_cma_pool: dsp1_cma@99000000 { |
| 30 |
compatible = "shared-dma-pool"; |
| 31 |
reg = <0x0 0x99000000 0x0 0x4000000>; |
| 32 |
reusable; |
| 33 |
status = "okay"; |
| 34 |
}; |
| 35 |
|
| 36 |
ipu1_cma_pool: ipu1_cma@9d000000 { |
| 37 |
compatible = "shared-dma-pool"; |
| 38 |
reg = <0x0 0x9d000000 0x0 0x2000000>; |
| 39 |
reusable; |
| 40 |
status = "okay"; |
| 41 |
}; |
| 42 |
}; |
| 43 |
|
| 44 |
evm_1v8_sw: fixedregulator-evm_1v8 { |
| 45 |
compatible = "regulator-fixed"; |
| 46 |
regulator-name = "evm_1v8"; |
| 47 |
regulator-min-microvolt = <1800000>; |
| 48 |
regulator-max-microvolt = <1800000>; |
| 49 |
vin-supply = <&smps4_reg>; |
| 50 |
regulator-always-on; |
| 51 |
regulator-boot-on; |
| 52 |
}; |
| 53 |
}; |
| 54 |
|
| 55 |
&i2c1 { |
| 56 |
tps65917: tps65917@58 { |
| 57 |
reg = <0x58>; |
| 58 |
|
| 59 |
interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */ |
| 60 |
}; |
| 61 |
}; |
| 62 |
|
| 63 |
#include "dra72-evm-tps65917.dtsi" |
| 64 |
|
| 65 |
&ldo2_reg { |
| 66 |
/* LDO2_OUT --> VDDA_1V8_PHY2 */ |
| 67 |
regulator-always-on; |
| 68 |
regulator-boot-on; |
| 69 |
}; |
| 70 |
|
| 71 |
&hdmi { |
| 72 |
vdda-supply = <&ldo2_reg>; |
| 73 |
}; |
| 74 |
|
| 75 |
&pcf_gpio_21 { |
| 76 |
interrupt-parent = <&gpio3>; |
| 77 |
interrupts = <30 IRQ_TYPE_EDGE_FALLING>; |
| 78 |
}; |
| 79 |
|
| 80 |
&mac_sw { |
| 81 |
mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_LOW>, |
| 82 |
<&pcf_hdmi 9 GPIO_ACTIVE_LOW>, /* P11 */ |
| 83 |
<&pcf_hdmi 10 GPIO_ACTIVE_LOW>; /* P12 */ |
| 84 |
status = "okay"; |
| 85 |
}; |
| 86 |
|
| 87 |
&cpsw_port1 { |
| 88 |
phy-handle = <&dp83867_0>; |
| 89 |
phy-mode = "rgmii-id"; |
| 90 |
ti,dual-emac-pvid = <1>; |
| 91 |
}; |
| 92 |
|
| 93 |
&cpsw_port2 { |
| 94 |
phy-handle = <&dp83867_1>; |
| 95 |
phy-mode = "rgmii-id"; |
| 96 |
ti,dual-emac-pvid = <2>; |
| 97 |
}; |
| 98 |
|
| 99 |
&davinci_mdio_sw { |
| 100 |
dp83867_0: ethernet-phy@2 { |
| 101 |
reg = <2>; |
| 102 |
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; |
| 103 |
ti,tx-internal-delay = <DP83867_RGMIIDCTL_250_PS>; |
| 104 |
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>; |
| 105 |
ti,min-output-impedance; |
| 106 |
interrupt-parent = <&gpio6>; |
| 107 |
interrupts = <16 IRQ_TYPE_EDGE_FALLING>; |
| 108 |
ti,dp83867-rxctrl-strap-quirk; |
| 109 |
}; |
| 110 |
|
| 111 |
dp83867_1: ethernet-phy@3 { |
| 112 |
reg = <3>; |
| 113 |
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; |
| 114 |
ti,tx-internal-delay = <DP83867_RGMIIDCTL_250_PS>; |
| 115 |
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>; |
| 116 |
ti,min-output-impedance; |
| 117 |
interrupt-parent = <&gpio6>; |
| 118 |
interrupts = <16 IRQ_TYPE_EDGE_FALLING>; |
| 119 |
ti,dp83867-rxctrl-strap-quirk; |
| 120 |
}; |
| 121 |
}; |
| 122 |
|
| 123 |
&mmc1 { |
| 124 |
pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104"; |
| 125 |
pinctrl-0 = <&mmc1_pins_default>; |
| 126 |
pinctrl-1 = <&mmc1_pins_hs>; |
| 127 |
pinctrl-2 = <&mmc1_pins_sdr12>; |
| 128 |
pinctrl-3 = <&mmc1_pins_sdr25>; |
| 129 |
pinctrl-4 = <&mmc1_pins_sdr50>; |
| 130 |
pinctrl-5 = <&mmc1_pins_ddr50_rev20 &mmc1_iodelay_ddr50_conf>; |
| 131 |
pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>; |
| 132 |
vqmmc-supply = <&ldo1_reg>; |
| 133 |
}; |
| 134 |
|
| 135 |
&mmc2 { |
| 136 |
pinctrl-names = "default", "hs", "ddr_1_8v", "hs200_1_8v"; |
| 137 |
pinctrl-0 = <&mmc2_pins_default>; |
| 138 |
pinctrl-1 = <&mmc2_pins_hs>; |
| 139 |
pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>; |
| 140 |
pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>; |
| 141 |
vmmc-supply = <&evm_1v8_sw>; |
| 142 |
}; |
| 143 |
|
| 144 |
&ipu2 { |
| 145 |
status = "okay"; |
| 146 |
memory-region = <&ipu2_cma_pool>; |
| 147 |
}; |
| 148 |
|
| 149 |
&ipu1 { |
| 150 |
status = "okay"; |
| 151 |
memory-region = <&ipu1_cma_pool>; |
| 152 |
}; |
| 153 |
|
| 154 |
&dsp1 { |
| 155 |
status = "okay"; |
| 156 |
memory-region = <&dsp1_cma_pool>; |
| 157 |
}; |