| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Device Tree Source for IGEP COM MODULE Rev. G (TI OMAP AM/DM37x) |
| 4 |
* |
| 5 |
* Copyright (C) 2014 Javier Martinez Canillas <[email protected]> |
| 6 |
* Copyright (C) 2014 Enric Balletbo i Serra <[email protected]> |
| 7 |
*/ |
| 8 |
|
| 9 |
#include "omap3-igep0030-common.dtsi" |
| 10 |
|
| 11 |
/ { |
| 12 |
model = "IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)"; |
| 13 |
compatible = "isee,omap3-igep0030-rev-g", "ti,omap3630", "ti,omap3"; |
| 14 |
|
| 15 |
/* Regulator to trigger the WL_EN signal of the Wifi module */ |
| 16 |
lbep5clwmc_wlen: regulator-lbep5clwmc-wlen { |
| 17 |
compatible = "regulator-fixed"; |
| 18 |
regulator-name = "regulator-lbep5clwmc-wlen"; |
| 19 |
regulator-min-microvolt = <3300000>; |
| 20 |
regulator-max-microvolt = <3300000>; |
| 21 |
gpio = <&gpio5 11 GPIO_ACTIVE_HIGH>; /* gpio_139 - WL_EN */ |
| 22 |
enable-active-high; |
| 23 |
}; |
| 24 |
}; |
| 25 |
|
| 26 |
&omap3_pmx_core { |
| 27 |
lbep5clwmc_pins: lbep5clwmc-pins { |
| 28 |
pinctrl-single,pins = < |
| 29 |
OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT | MUX_MODE4) /* sdmmc2_dat4.gpio_136 - W_IRQ */ |
| 30 |
OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat5.gpio_137 - BT_EN */ |
| 31 |
OMAP3_CORE1_IOPAD(0x216a, PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat7.gpio_139 - WL_EN */ |
| 32 |
>; |
| 33 |
}; |
| 34 |
|
| 35 |
leds_pins: leds-pins { |
| 36 |
pinctrl-single,pins = < |
| 37 |
OMAP3_CORE1_IOPAD(0x21be, PIN_OUTPUT | MUX_MODE4) /* i2c2_scl.gpio_168 */ |
| 38 |
>; |
| 39 |
}; |
| 40 |
|
| 41 |
}; |
| 42 |
|
| 43 |
&i2c2 { |
| 44 |
status = "disabled"; |
| 45 |
}; |
| 46 |
|
| 47 |
&leds { |
| 48 |
pinctrl-names = "default"; |
| 49 |
pinctrl-0 = <&leds_pins &leds_core2_pins>; |
| 50 |
|
| 51 |
boot { |
| 52 |
label = "omap3:green:boot"; |
| 53 |
gpios = <&gpio6 8 GPIO_ACTIVE_HIGH>; |
| 54 |
default-state = "on"; |
| 55 |
}; |
| 56 |
}; |
| 57 |
|
| 58 |
&mmc2 { |
| 59 |
pinctrl-names = "default"; |
| 60 |
pinctrl-0 = <&mmc2_pins &lbep5clwmc_pins>; |
| 61 |
vmmc-supply = <&lbep5clwmc_wlen>; |
| 62 |
bus-width = <4>; |
| 63 |
non-removable; |
| 64 |
|
| 65 |
#address-cells = <1>; |
| 66 |
#size-cells = <0>; |
| 67 |
wlcore: wlcore@2 { |
| 68 |
compatible = "ti,wl1835"; |
| 69 |
reg = <2>; |
| 70 |
interrupt-parent = <&gpio5>; |
| 71 |
interrupts = <8 IRQ_TYPE_EDGE_RISING>; /* gpio 136 */ |
| 72 |
}; |
| 73 |
}; |
| 74 |
|
| 75 |
&uart2 { |
| 76 |
bluetooth { |
| 77 |
compatible = "ti,wl1835-st"; |
| 78 |
enable-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>; /* gpio 137 */ |
| 79 |
max-speed = <300000>; |
| 80 |
}; |
| 81 |
}; |