| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
|
| 3 |
#include <dt-bindings/input/input.h> |
| 4 |
|
| 5 |
/ { |
| 6 |
chosen { |
| 7 |
stdout-path = &uart1; |
| 8 |
}; |
| 9 |
|
| 10 |
cpus { |
| 11 |
cpu@0 { |
| 12 |
cpu0-supply = <&vcc>; |
| 13 |
}; |
| 14 |
}; |
| 15 |
|
| 16 |
memory@80000000 { |
| 17 |
device_type = "memory"; |
| 18 |
reg = <0x80000000 0>; |
| 19 |
}; |
| 20 |
|
| 21 |
leds { |
| 22 |
compatible = "gpio-leds"; |
| 23 |
led-user0 { |
| 24 |
label = "user0"; |
| 25 |
gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* LEDA */ |
| 26 |
linux,default-trigger = "none"; |
| 27 |
}; |
| 28 |
}; |
| 29 |
|
| 30 |
/* fixed 26MHz oscillator */ |
| 31 |
hfclk_26m: oscillator { |
| 32 |
#clock-cells = <0>; |
| 33 |
compatible = "fixed-clock"; |
| 34 |
clock-frequency = <26000000>; |
| 35 |
}; |
| 36 |
}; |
| 37 |
|
| 38 |
/* The Torpedo doesn't route the USB host pins */ |
| 39 |
&usbhshost { |
| 40 |
status = "disabled"; |
| 41 |
}; |
| 42 |
|
| 43 |
&gpmc { |
| 44 |
ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */ |
| 45 |
|
| 46 |
nand@0,0 { |
| 47 |
compatible = "ti,omap2-nand"; |
| 48 |
reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ |
| 49 |
interrupt-parent = <&gpmc>; |
| 50 |
interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ |
| 51 |
<1 IRQ_TYPE_NONE>; /* termcount */ |
| 52 |
nand-bus-width = <16>; |
| 53 |
ti,nand-ecc-opt = "bch8"; |
| 54 |
rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */ |
| 55 |
gpmc,sync-clk-ps = <0>; |
| 56 |
gpmc,cs-on-ns = <0>; |
| 57 |
gpmc,cs-rd-off-ns = <44>; |
| 58 |
gpmc,cs-wr-off-ns = <44>; |
| 59 |
gpmc,adv-on-ns = <6>; |
| 60 |
gpmc,adv-rd-off-ns = <34>; |
| 61 |
gpmc,adv-wr-off-ns = <44>; |
| 62 |
gpmc,we-off-ns = <40>; |
| 63 |
gpmc,oe-off-ns = <54>; |
| 64 |
gpmc,access-ns = <64>; |
| 65 |
gpmc,rd-cycle-ns = <82>; |
| 66 |
gpmc,wr-cycle-ns = <82>; |
| 67 |
gpmc,wr-access-ns = <40>; |
| 68 |
gpmc,wr-data-mux-bus-ns = <0>; |
| 69 |
gpmc,device-width = <2>; |
| 70 |
#address-cells = <1>; |
| 71 |
#size-cells = <1>; |
| 72 |
}; |
| 73 |
}; |
| 74 |
|
| 75 |
&i2c1 { |
| 76 |
pinctrl-names = "default"; |
| 77 |
pinctrl-0 = <&i2c1_pins>; |
| 78 |
clock-frequency = <2600000>; |
| 79 |
|
| 80 |
twl: twl@48 { |
| 81 |
reg = <0x48>; |
| 82 |
interrupts = <7>; /* SYS_NIRQ cascaded to intc */ |
| 83 |
interrupt-parent = <&intc>; |
| 84 |
clocks = <&hfclk_26m>; |
| 85 |
clock-names = "fck"; |
| 86 |
|
| 87 |
twl_audio: audio { |
| 88 |
compatible = "ti,twl4030-audio"; |
| 89 |
codec { |
| 90 |
}; |
| 91 |
}; |
| 92 |
}; |
| 93 |
}; |
| 94 |
|
| 95 |
&i2c2 { |
| 96 |
pinctrl-names = "default"; |
| 97 |
pinctrl-0 = <&i2c2_pins>; |
| 98 |
clock-frequency = <400000>; |
| 99 |
}; |
| 100 |
|
| 101 |
&i2c3 { |
| 102 |
pinctrl-names = "default"; |
| 103 |
pinctrl-0 = <&i2c3_pins>; |
| 104 |
clock-frequency = <400000>; |
| 105 |
eeprom@50 { |
| 106 |
compatible = "atmel,24c64"; |
| 107 |
readonly; |
| 108 |
reg = <0x50>; |
| 109 |
}; |
| 110 |
}; |
| 111 |
|
| 112 |
&omap3_pmx_core { |
| 113 |
mcbsp2_pins: mcbsp2-pins { |
| 114 |
pinctrl-single,pins = < |
| 115 |
OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */ |
| 116 |
OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */ |
| 117 |
OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */ |
| 118 |
OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */ |
| 119 |
>; |
| 120 |
}; |
| 121 |
uart2_pins: uart2-pins { |
| 122 |
pinctrl-single,pins = < |
| 123 |
OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */ |
| 124 |
OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/ |
| 125 |
OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ |
| 126 |
OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */ |
| 127 |
OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */ |
| 128 |
>; |
| 129 |
}; |
| 130 |
mcspi1_pins: mcspi1-pins { |
| 131 |
pinctrl-single,pins = < |
| 132 |
OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ |
| 133 |
OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */ |
| 134 |
OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */ |
| 135 |
OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */ |
| 136 |
>; |
| 137 |
}; |
| 138 |
hsusb_otg_pins: hsusb-otg-pins { |
| 139 |
pinctrl-single,pins = < |
| 140 |
OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */ |
| 141 |
OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */ |
| 142 |
OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */ |
| 143 |
OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */ |
| 144 |
|
| 145 |
OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */ |
| 146 |
OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */ |
| 147 |
OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */ |
| 148 |
OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */ |
| 149 |
OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */ |
| 150 |
OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */ |
| 151 |
OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */ |
| 152 |
OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */ |
| 153 |
>; |
| 154 |
}; |
| 155 |
i2c1_pins: i2c1-pins { |
| 156 |
pinctrl-single,pins = < |
| 157 |
OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ |
| 158 |
OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ |
| 159 |
>; |
| 160 |
}; |
| 161 |
i2c2_pins: i2c2-pins { |
| 162 |
pinctrl-single,pins = < |
| 163 |
OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl */ |
| 164 |
OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda */ |
| 165 |
>; |
| 166 |
}; |
| 167 |
i2c3_pins: i2c3-pins { |
| 168 |
pinctrl-single,pins = < |
| 169 |
OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl */ |
| 170 |
OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda */ |
| 171 |
>; |
| 172 |
}; |
| 173 |
}; |
| 174 |
|
| 175 |
&uart2 { |
| 176 |
interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>; |
| 177 |
pinctrl-names = "default"; |
| 178 |
pinctrl-0 = <&uart2_pins>; |
| 179 |
}; |
| 180 |
|
| 181 |
&mcspi1 { |
| 182 |
pinctrl-names = "default"; |
| 183 |
pinctrl-0 = <&mcspi1_pins>; |
| 184 |
}; |
| 185 |
|
| 186 |
#include "twl4030.dtsi" |
| 187 |
#include "twl4030_omap3.dtsi" |
| 188 |
|
| 189 |
&twl { |
| 190 |
twl_power: power { |
| 191 |
compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle"; |
| 192 |
ti,use_poweroff; |
| 193 |
}; |
| 194 |
}; |
| 195 |
|
| 196 |
&twl_gpio { |
| 197 |
ti,use-leds; |
| 198 |
}; |
| 199 |
|
| 200 |
&twl_keypad { |
| 201 |
status = "disabled"; |
| 202 |
}; |