| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/ |
| 4 |
* |
| 5 |
* Based on "omap4.dtsi" |
| 6 |
*/ |
| 7 |
|
| 8 |
#include <dt-bindings/bus/ti-sysc.h> |
| 9 |
#include <dt-bindings/clock/dra7.h> |
| 10 |
#include <dt-bindings/interrupt-controller/arm-gic.h> |
| 11 |
#include <dt-bindings/pinctrl/dra.h> |
| 12 |
|
| 13 |
#define MAX_SOURCES 400 |
| 14 |
|
| 15 |
/ { |
| 16 |
#address-cells = <2>; |
| 17 |
#size-cells = <2>; |
| 18 |
|
| 19 |
compatible = "ti,dra7xx"; |
| 20 |
interrupt-parent = <&crossbar_mpu>; |
| 21 |
chosen { }; |
| 22 |
|
| 23 |
aliases { |
| 24 |
i2c0 = &i2c1; |
| 25 |
i2c1 = &i2c2; |
| 26 |
i2c2 = &i2c3; |
| 27 |
i2c3 = &i2c4; |
| 28 |
i2c4 = &i2c5; |
| 29 |
serial0 = &uart1; |
| 30 |
serial1 = &uart2; |
| 31 |
serial2 = &uart3; |
| 32 |
serial3 = &uart4; |
| 33 |
serial4 = &uart5; |
| 34 |
serial5 = &uart6; |
| 35 |
serial6 = &uart7; |
| 36 |
serial7 = &uart8; |
| 37 |
serial8 = &uart9; |
| 38 |
serial9 = &uart10; |
| 39 |
ethernet0 = &cpsw_port1; |
| 40 |
ethernet1 = &cpsw_port2; |
| 41 |
d_can0 = &dcan1; |
| 42 |
d_can1 = &dcan2; |
| 43 |
spi0 = &qspi; |
| 44 |
}; |
| 45 |
|
| 46 |
timer { |
| 47 |
compatible = "arm,armv7-timer"; |
| 48 |
status = "disabled"; /* See ARM architected timer wrap erratum i940 */ |
| 49 |
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, |
| 50 |
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, |
| 51 |
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, |
| 52 |
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>; |
| 53 |
interrupt-parent = <&gic>; |
| 54 |
}; |
| 55 |
|
| 56 |
gic: interrupt-controller@48211000 { |
| 57 |
compatible = "arm,cortex-a15-gic"; |
| 58 |
interrupt-controller; |
| 59 |
#interrupt-cells = <3>; |
| 60 |
reg = <0x0 0x48211000 0x0 0x1000>, |
| 61 |
<0x0 0x48212000 0x0 0x2000>, |
| 62 |
<0x0 0x48214000 0x0 0x2000>, |
| 63 |
<0x0 0x48216000 0x0 0x2000>; |
| 64 |
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; |
| 65 |
interrupt-parent = <&gic>; |
| 66 |
}; |
| 67 |
|
| 68 |
wakeupgen: interrupt-controller@48281000 { |
| 69 |
compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu"; |
| 70 |
interrupt-controller; |
| 71 |
#interrupt-cells = <3>; |
| 72 |
reg = <0x0 0x48281000 0x0 0x1000>; |
| 73 |
interrupt-parent = <&gic>; |
| 74 |
}; |
| 75 |
|
| 76 |
cpus { |
| 77 |
#address-cells = <1>; |
| 78 |
#size-cells = <0>; |
| 79 |
|
| 80 |
cpu0: cpu@0 { |
| 81 |
device_type = "cpu"; |
| 82 |
compatible = "arm,cortex-a15"; |
| 83 |
reg = <0>; |
| 84 |
|
| 85 |
operating-points-v2 = <&cpu0_opp_table>; |
| 86 |
|
| 87 |
clocks = <&dpll_mpu_ck>; |
| 88 |
clock-names = "cpu"; |
| 89 |
|
| 90 |
clock-latency = <300000>; /* From omap-cpufreq driver */ |
| 91 |
|
| 92 |
/* cooling options */ |
| 93 |
#cooling-cells = <2>; /* min followed by max */ |
| 94 |
|
| 95 |
vbb-supply = <&abb_mpu>; |
| 96 |
}; |
| 97 |
}; |
| 98 |
|
| 99 |
cpu0_opp_table: opp-table { |
| 100 |
compatible = "operating-points-v2-ti-cpu"; |
| 101 |
syscon = <&scm_wkup>; |
| 102 |
|
| 103 |
opp-1000000000 { |
| 104 |
/* OPP NOM */ |
| 105 |
opp-hz = /bits/ 64 <1000000000>; |
| 106 |
opp-microvolt = <1060000 850000 1150000>, |
| 107 |
<1060000 850000 1150000>; |
| 108 |
opp-supported-hw = <0xFF 0x01>; |
| 109 |
opp-suspend; |
| 110 |
}; |
| 111 |
|
| 112 |
opp-1176000000 { |
| 113 |
/* OPP OD */ |
| 114 |
opp-hz = /bits/ 64 <1176000000>; |
| 115 |
opp-microvolt = <1160000 885000 1160000>, |
| 116 |
<1160000 885000 1160000>; |
| 117 |
|
| 118 |
opp-supported-hw = <0xFF 0x02>; |
| 119 |
}; |
| 120 |
|
| 121 |
opp-1500000000 { |
| 122 |
/* OPP High */ |
| 123 |
opp-hz = /bits/ 64 <1500000000>; |
| 124 |
opp-microvolt = <1210000 950000 1250000>, |
| 125 |
<1210000 950000 1250000>; |
| 126 |
opp-supported-hw = <0xFF 0x04>; |
| 127 |
}; |
| 128 |
}; |
| 129 |
|
| 130 |
/* |
| 131 |
* XXX: Use a flat representation of the SOC interconnect. |
| 132 |
* The real OMAP interconnect network is quite complex. |
| 133 |
* Since it will not bring real advantage to represent that in DT for |
| 134 |
* the moment, just use a fake OCP bus entry to represent the whole bus |
| 135 |
* hierarchy. |
| 136 |
*/ |
| 137 |
ocp: ocp { |
| 138 |
compatible = "simple-pm-bus"; |
| 139 |
power-domains = <&prm_core>; |
| 140 |
clocks = <&l3main1_clkctrl DRA7_L3MAIN1_L3_MAIN_1_CLKCTRL 0>, |
| 141 |
<&l3instr_clkctrl DRA7_L3INSTR_L3_MAIN_2_CLKCTRL 0>; |
| 142 |
#address-cells = <1>; |
| 143 |
#size-cells = <1>; |
| 144 |
ranges = <0x0 0x0 0x0 0xc0000000>; |
| 145 |
dma-ranges = <0x80000000 0x0 0x80000000 0x80000000>; |
| 146 |
|
| 147 |
l3-noc@44000000 { |
| 148 |
compatible = "ti,dra7-l3-noc"; |
| 149 |
reg = <0x44000000 0x1000000>, |
| 150 |
<0x45000000 0x1000>; |
| 151 |
interrupts-extended = <&crossbar_mpu GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, |
| 152 |
<&wakeupgen GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| 153 |
}; |
| 154 |
|
| 155 |
l4_cfg: interconnect@4a000000 { |
| 156 |
}; |
| 157 |
l4_wkup: interconnect@4ae00000 { |
| 158 |
}; |
| 159 |
l4_per1: interconnect@48000000 { |
| 160 |
}; |
| 161 |
|
| 162 |
target-module@48210000 { |
| 163 |
compatible = "ti,sysc-omap4-simple", "ti,sysc"; |
| 164 |
power-domains = <&prm_mpu>; |
| 165 |
clocks = <&mpu_clkctrl DRA7_MPU_MPU_CLKCTRL 0>; |
| 166 |
clock-names = "fck"; |
| 167 |
#address-cells = <1>; |
| 168 |
#size-cells = <1>; |
| 169 |
ranges = <0 0x48210000 0x1f0000>; |
| 170 |
|
| 171 |
mpu { |
| 172 |
compatible = "ti,omap5-mpu"; |
| 173 |
}; |
| 174 |
}; |
| 175 |
|
| 176 |
l4_per2: interconnect@48400000 { |
| 177 |
}; |
| 178 |
l4_per3: interconnect@48800000 { |
| 179 |
}; |
| 180 |
|
| 181 |
/* |
| 182 |
* Register access seems to have complex dependencies and also |
| 183 |
* seems to need an enabled phy. See the TRM chapter for "Table |
| 184 |
* 26-678. Main Sequence PCIe Controller Global Initialization" |
| 185 |
* and also dra7xx_pcie_probe(). |
| 186 |
*/ |
| 187 |
axi0: target-module@51000000 { |
| 188 |
compatible = "ti,sysc-omap4", "ti,sysc"; |
| 189 |
power-domains = <&prm_l3init>; |
| 190 |
resets = <&prm_l3init 0>; |
| 191 |
reset-names = "rstctrl"; |
| 192 |
clocks = <&pcie_clkctrl DRA7_PCIE_PCIE1_CLKCTRL 0>, |
| 193 |
<&pcie_clkctrl DRA7_PCIE_PCIE1_CLKCTRL 9>, |
| 194 |
<&pcie_clkctrl DRA7_PCIE_PCIE1_CLKCTRL 10>; |
| 195 |
clock-names = "fck", "phy-clk", "phy-clk-div"; |
| 196 |
#size-cells = <1>; |
| 197 |
#address-cells = <1>; |
| 198 |
ranges = <0x51000000 0x51000000 0x3000 |
| 199 |
0x0 0x20000000 0x10000000>; |
| 200 |
dma-ranges; |
| 201 |
/** |
| 202 |
* To enable PCI endpoint mode, disable the pcie1_rc |
| 203 |
* node and enable pcie1_ep mode. |
| 204 |
*/ |
| 205 |
pcie1_rc: pcie@51000000 { |
| 206 |
reg = <0x51000000 0x2000>, <0x51002000 0x14c>, <0x1000 0x2000>; |
| 207 |
reg-names = "rc_dbics", "ti_conf", "config"; |
| 208 |
interrupts = <0 232 0x4>, <0 233 0x4>; |
| 209 |
#address-cells = <3>; |
| 210 |
#size-cells = <2>; |
| 211 |
device_type = "pci"; |
| 212 |
ranges = <0x81000000 0 0 0x03000 0 0x00010000 |
| 213 |
0x82000000 0 0x20013000 0x13000 0 0xffed000>; |
| 214 |
bus-range = <0x00 0xff>; |
| 215 |
#interrupt-cells = <1>; |
| 216 |
num-lanes = <1>; |
| 217 |
linux,pci-domain = <0>; |
| 218 |
phys = <&pcie1_phy>; |
| 219 |
phy-names = "pcie-phy0"; |
| 220 |
ti,syscon-lane-sel = <&scm_conf_pcie 0x18>; |
| 221 |
interrupt-map-mask = <0 0 0 7>; |
| 222 |
interrupt-map = <0 0 0 1 &pcie1_intc 1>, |
| 223 |
<0 0 0 2 &pcie1_intc 2>, |
| 224 |
<0 0 0 3 &pcie1_intc 3>, |
| 225 |
<0 0 0 4 &pcie1_intc 4>; |
| 226 |
ti,syscon-unaligned-access = <&scm_conf1 0x14 1>; |
| 227 |
status = "disabled"; |
| 228 |
pcie1_intc: interrupt-controller { |
| 229 |
interrupt-controller; |
| 230 |
#address-cells = <0>; |
| 231 |
#interrupt-cells = <1>; |
| 232 |
}; |
| 233 |
}; |
| 234 |
|
| 235 |
pcie1_ep: pcie_ep@51000000 { |
| 236 |
reg = <0x51000000 0x28>, <0x51002000 0x14c>, <0x51001000 0x28>, <0x1000 0x10000000>; |
| 237 |
reg-names = "ep_dbics", "ti_conf", "ep_dbics2", "addr_space"; |
| 238 |
interrupts = <0 232 0x4>; |
| 239 |
num-lanes = <1>; |
| 240 |
num-ib-windows = <4>; |
| 241 |
num-ob-windows = <16>; |
| 242 |
phys = <&pcie1_phy>; |
| 243 |
phy-names = "pcie-phy0"; |
| 244 |
ti,syscon-unaligned-access = <&scm_conf1 0x14 1>; |
| 245 |
ti,syscon-lane-sel = <&scm_conf_pcie 0x18>; |
| 246 |
status = "disabled"; |
| 247 |
}; |
| 248 |
}; |
| 249 |
|
| 250 |
/* |
| 251 |
* Register access seems to have complex dependencies and also |
| 252 |
* seems to need an enabled phy. See the TRM chapter for "Table |
| 253 |
* 26-678. Main Sequence PCIe Controller Global Initialization" |
| 254 |
* and also dra7xx_pcie_probe(). |
| 255 |
*/ |
| 256 |
axi1: target-module@51800000 { |
| 257 |
compatible = "ti,sysc-omap4", "ti,sysc"; |
| 258 |
clocks = <&pcie_clkctrl DRA7_PCIE_PCIE2_CLKCTRL 0>, |
| 259 |
<&pcie_clkctrl DRA7_PCIE_PCIE2_CLKCTRL 9>, |
| 260 |
<&pcie_clkctrl DRA7_PCIE_PCIE2_CLKCTRL 10>; |
| 261 |
clock-names = "fck", "phy-clk", "phy-clk-div"; |
| 262 |
power-domains = <&prm_l3init>; |
| 263 |
resets = <&prm_l3init 1>; |
| 264 |
reset-names = "rstctrl"; |
| 265 |
#size-cells = <1>; |
| 266 |
#address-cells = <1>; |
| 267 |
ranges = <0x51800000 0x51800000 0x3000 |
| 268 |
0x0 0x30000000 0x10000000>; |
| 269 |
dma-ranges; |
| 270 |
status = "disabled"; |
| 271 |
pcie2_rc: pcie@51800000 { |
| 272 |
reg = <0x51800000 0x2000>, <0x51802000 0x14c>, <0x1000 0x2000>; |
| 273 |
reg-names = "rc_dbics", "ti_conf", "config"; |
| 274 |
interrupts = <0 355 0x4>, <0 356 0x4>; |
| 275 |
#address-cells = <3>; |
| 276 |
#size-cells = <2>; |
| 277 |
device_type = "pci"; |
| 278 |
ranges = <0x81000000 0 0 0x03000 0 0x00010000 |
| 279 |
0x82000000 0 0x30013000 0x13000 0 0xffed000>; |
| 280 |
bus-range = <0x00 0xff>; |
| 281 |
#interrupt-cells = <1>; |
| 282 |
num-lanes = <1>; |
| 283 |
linux,pci-domain = <1>; |
| 284 |
phys = <&pcie2_phy>; |
| 285 |
phy-names = "pcie-phy0"; |
| 286 |
interrupt-map-mask = <0 0 0 7>; |
| 287 |
interrupt-map = <0 0 0 1 &pcie2_intc 1>, |
| 288 |
<0 0 0 2 &pcie2_intc 2>, |
| 289 |
<0 0 0 3 &pcie2_intc 3>, |
| 290 |
<0 0 0 4 &pcie2_intc 4>; |
| 291 |
ti,syscon-unaligned-access = <&scm_conf1 0x14 2>; |
| 292 |
pcie2_intc: interrupt-controller { |
| 293 |
interrupt-controller; |
| 294 |
#address-cells = <0>; |
| 295 |
#interrupt-cells = <1>; |
| 296 |
}; |
| 297 |
}; |
| 298 |
}; |
| 299 |
|
| 300 |
ocmcram1: ocmcram@40300000 { |
| 301 |
compatible = "mmio-sram"; |
| 302 |
reg = <0x40300000 0x80000>; |
| 303 |
ranges = <0x0 0x40300000 0x80000>; |
| 304 |
#address-cells = <1>; |
| 305 |
#size-cells = <1>; |
| 306 |
/* |
| 307 |
* This is a placeholder for an optional reserved |
| 308 |
* region for use by secure software. The size |
| 309 |
* of this region is not known until runtime so it |
| 310 |
* is set as zero to either be updated to reserve |
| 311 |
* space or left unchanged to leave all SRAM for use. |
| 312 |
* On HS parts that that require the reserved region |
| 313 |
* either the bootloader can update the size to |
| 314 |
* the required amount or the node can be overridden |
| 315 |
* from the board dts file for the secure platform. |
| 316 |
*/ |
| 317 |
sram-hs@0 { |
| 318 |
compatible = "ti,secure-ram"; |
| 319 |
reg = <0x0 0x0>; |
| 320 |
}; |
| 321 |
}; |
| 322 |
|
| 323 |
/* |
| 324 |
* NOTE: ocmcram2 and ocmcram3 are not available on all |
| 325 |
* DRA7xx and AM57xx variants. Confirm availability in |
| 326 |
* the data manual for the exact part number in use |
| 327 |
* before enabling these nodes in the board dts file. |
| 328 |
*/ |
| 329 |
ocmcram2: ocmcram@40400000 { |
| 330 |
status = "disabled"; |
| 331 |
compatible = "mmio-sram"; |
| 332 |
reg = <0x40400000 0x100000>; |
| 333 |
ranges = <0x0 0x40400000 0x100000>; |
| 334 |
#address-cells = <1>; |
| 335 |
#size-cells = <1>; |
| 336 |
}; |
| 337 |
|
| 338 |
ocmcram3: ocmcram@40500000 { |
| 339 |
status = "disabled"; |
| 340 |
compatible = "mmio-sram"; |
| 341 |
reg = <0x40500000 0x100000>; |
| 342 |
ranges = <0x0 0x40500000 0x100000>; |
| 343 |
#address-cells = <1>; |
| 344 |
#size-cells = <1>; |
| 345 |
}; |
| 346 |
|
| 347 |
bandgap: bandgap@4a0021e0 { |
| 348 |
reg = <0x4a0021e0 0xc |
| 349 |
0x4a00232c 0xc |
| 350 |
0x4a002380 0x2c |
| 351 |
0x4a0023C0 0x3c |
| 352 |
0x4a002564 0x8 |
| 353 |
0x4a002574 0x50>; |
| 354 |
compatible = "ti,dra752-bandgap"; |
| 355 |
interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; |
| 356 |
#thermal-sensor-cells = <1>; |
| 357 |
}; |
| 358 |
|
| 359 |
dsp1_system: dsp_system@40d00000 { |
| 360 |
compatible = "syscon"; |
| 361 |
reg = <0x40d00000 0x100>; |
| 362 |
}; |
| 363 |
|
| 364 |
dra7_iodelay_core: padconf@4844a000 { |
| 365 |
compatible = "ti,dra7-iodelay"; |
| 366 |
reg = <0x4844a000 0x0d1c>; |
| 367 |
#address-cells = <1>; |
| 368 |
#size-cells = <0>; |
| 369 |
#pinctrl-cells = <2>; |
| 370 |
}; |
| 371 |
|
| 372 |
target-module@43300000 { |
| 373 |
compatible = "ti,sysc-omap4", "ti,sysc"; |
| 374 |
reg = <0x43300000 0x4>, |
| 375 |
<0x43300010 0x4>; |
| 376 |
reg-names = "rev", "sysc"; |
| 377 |
ti,sysc-midle = <SYSC_IDLE_FORCE>, |
| 378 |
<SYSC_IDLE_NO>, |
| 379 |
<SYSC_IDLE_SMART>; |
| 380 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 381 |
<SYSC_IDLE_NO>, |
| 382 |
<SYSC_IDLE_SMART>; |
| 383 |
clocks = <&l3main1_clkctrl DRA7_L3MAIN1_TPCC_CLKCTRL 0>; |
| 384 |
clock-names = "fck"; |
| 385 |
#address-cells = <1>; |
| 386 |
#size-cells = <1>; |
| 387 |
ranges = <0x0 0x43300000 0x100000>; |
| 388 |
|
| 389 |
edma: dma@0 { |
| 390 |
compatible = "ti,edma3-tpcc"; |
| 391 |
reg = <0 0x100000>; |
| 392 |
reg-names = "edma3_cc"; |
| 393 |
interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>, |
| 394 |
<GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>, |
| 395 |
<GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>; |
| 396 |
interrupt-names = "edma3_ccint", "edma3_mperr", |
| 397 |
"edma3_ccerrint"; |
| 398 |
dma-requests = <64>; |
| 399 |
#dma-cells = <2>; |
| 400 |
|
| 401 |
ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 0>; |
| 402 |
|
| 403 |
/* |
| 404 |
* memcpy is disabled, can be enabled with: |
| 405 |
* ti,edma-memcpy-channels = <20 21>; |
| 406 |
* for example. Note that these channels need to be |
| 407 |
* masked in the xbar as well. |
| 408 |
*/ |
| 409 |
}; |
| 410 |
}; |
| 411 |
|
| 412 |
target-module@43400000 { |
| 413 |
compatible = "ti,sysc-omap4", "ti,sysc"; |
| 414 |
reg = <0x43400000 0x4>, |
| 415 |
<0x43400010 0x4>; |
| 416 |
reg-names = "rev", "sysc"; |
| 417 |
ti,sysc-midle = <SYSC_IDLE_FORCE>, |
| 418 |
<SYSC_IDLE_NO>, |
| 419 |
<SYSC_IDLE_SMART>; |
| 420 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 421 |
<SYSC_IDLE_NO>, |
| 422 |
<SYSC_IDLE_SMART>; |
| 423 |
clocks = <&l3main1_clkctrl DRA7_L3MAIN1_TPTC0_CLKCTRL 0>; |
| 424 |
clock-names = "fck"; |
| 425 |
#address-cells = <1>; |
| 426 |
#size-cells = <1>; |
| 427 |
ranges = <0x0 0x43400000 0x100000>; |
| 428 |
|
| 429 |
edma_tptc0: dma@0 { |
| 430 |
compatible = "ti,edma3-tptc"; |
| 431 |
reg = <0 0x100000>; |
| 432 |
interrupts = <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>; |
| 433 |
interrupt-names = "edma3_tcerrint"; |
| 434 |
}; |
| 435 |
}; |
| 436 |
|
| 437 |
target-module@43500000 { |
| 438 |
compatible = "ti,sysc-omap4", "ti,sysc"; |
| 439 |
reg = <0x43500000 0x4>, |
| 440 |
<0x43500010 0x4>; |
| 441 |
reg-names = "rev", "sysc"; |
| 442 |
ti,sysc-midle = <SYSC_IDLE_FORCE>, |
| 443 |
<SYSC_IDLE_NO>, |
| 444 |
<SYSC_IDLE_SMART>; |
| 445 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 446 |
<SYSC_IDLE_NO>, |
| 447 |
<SYSC_IDLE_SMART>; |
| 448 |
clocks = <&l3main1_clkctrl DRA7_L3MAIN1_TPTC1_CLKCTRL 0>; |
| 449 |
clock-names = "fck"; |
| 450 |
#address-cells = <1>; |
| 451 |
#size-cells = <1>; |
| 452 |
ranges = <0x0 0x43500000 0x100000>; |
| 453 |
|
| 454 |
edma_tptc1: dma@0 { |
| 455 |
compatible = "ti,edma3-tptc"; |
| 456 |
reg = <0 0x100000>; |
| 457 |
interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>; |
| 458 |
interrupt-names = "edma3_tcerrint"; |
| 459 |
}; |
| 460 |
}; |
| 461 |
|
| 462 |
target-module@4e000000 { |
| 463 |
compatible = "ti,sysc-omap2", "ti,sysc"; |
| 464 |
reg = <0x4e000000 0x4>, |
| 465 |
<0x4e000010 0x4>; |
| 466 |
reg-names = "rev", "sysc"; |
| 467 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 468 |
<SYSC_IDLE_NO>, |
| 469 |
<SYSC_IDLE_SMART>; |
| 470 |
ranges = <0x0 0x4e000000 0x2000000>; |
| 471 |
#size-cells = <1>; |
| 472 |
#address-cells = <1>; |
| 473 |
|
| 474 |
dmm@0 { |
| 475 |
compatible = "ti,omap5-dmm"; |
| 476 |
reg = <0 0x800>; |
| 477 |
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; |
| 478 |
}; |
| 479 |
}; |
| 480 |
|
| 481 |
ipu1: ipu@58820000 { |
| 482 |
compatible = "ti,dra7-ipu"; |
| 483 |
reg = <0x58820000 0x10000>; |
| 484 |
reg-names = "l2ram"; |
| 485 |
iommus = <&mmu_ipu1>; |
| 486 |
status = "disabled"; |
| 487 |
resets = <&prm_ipu 0>, <&prm_ipu 1>; |
| 488 |
clocks = <&ipu1_clkctrl DRA7_IPU1_MMU_IPU1_CLKCTRL 0>; |
| 489 |
firmware-name = "dra7-ipu1-fw.xem4"; |
| 490 |
}; |
| 491 |
|
| 492 |
ipu2: ipu@55020000 { |
| 493 |
compatible = "ti,dra7-ipu"; |
| 494 |
reg = <0x55020000 0x10000>; |
| 495 |
reg-names = "l2ram"; |
| 496 |
iommus = <&mmu_ipu2>; |
| 497 |
status = "disabled"; |
| 498 |
resets = <&prm_core 0>, <&prm_core 1>; |
| 499 |
clocks = <&ipu2_clkctrl DRA7_IPU2_MMU_IPU2_CLKCTRL 0>; |
| 500 |
firmware-name = "dra7-ipu2-fw.xem4"; |
| 501 |
}; |
| 502 |
|
| 503 |
dsp1: dsp@40800000 { |
| 504 |
compatible = "ti,dra7-dsp"; |
| 505 |
reg = <0x40800000 0x48000>, |
| 506 |
<0x40e00000 0x8000>, |
| 507 |
<0x40f00000 0x8000>; |
| 508 |
reg-names = "l2ram", "l1pram", "l1dram"; |
| 509 |
ti,bootreg = <&scm_conf 0x55c 10>; |
| 510 |
iommus = <&mmu0_dsp1>, <&mmu1_dsp1>; |
| 511 |
status = "disabled"; |
| 512 |
resets = <&prm_dsp1 0>; |
| 513 |
clocks = <&dsp1_clkctrl DRA7_DSP1_MMU0_DSP1_CLKCTRL 0>; |
| 514 |
firmware-name = "dra7-dsp1-fw.xe66"; |
| 515 |
}; |
| 516 |
|
| 517 |
target-module@40d01000 { |
| 518 |
compatible = "ti,sysc-omap2", "ti,sysc"; |
| 519 |
reg = <0x40d01000 0x4>, |
| 520 |
<0x40d01010 0x4>, |
| 521 |
<0x40d01014 0x4>; |
| 522 |
reg-names = "rev", "sysc", "syss"; |
| 523 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 524 |
<SYSC_IDLE_NO>, |
| 525 |
<SYSC_IDLE_SMART>; |
| 526 |
ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | |
| 527 |
SYSC_OMAP2_SOFTRESET | |
| 528 |
SYSC_OMAP2_AUTOIDLE)>; |
| 529 |
clocks = <&dsp1_clkctrl DRA7_DSP1_MMU0_DSP1_CLKCTRL 0>; |
| 530 |
clock-names = "fck"; |
| 531 |
resets = <&prm_dsp1 1>; |
| 532 |
reset-names = "rstctrl"; |
| 533 |
ranges = <0x0 0x40d01000 0x1000>; |
| 534 |
#size-cells = <1>; |
| 535 |
#address-cells = <1>; |
| 536 |
|
| 537 |
mmu0_dsp1: mmu@0 { |
| 538 |
compatible = "ti,dra7-dsp-iommu"; |
| 539 |
reg = <0x0 0x100>; |
| 540 |
interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; |
| 541 |
#iommu-cells = <0>; |
| 542 |
ti,syscon-mmuconfig = <&dsp1_system 0x0>; |
| 543 |
}; |
| 544 |
}; |
| 545 |
|
| 546 |
target-module@40d02000 { |
| 547 |
compatible = "ti,sysc-omap2", "ti,sysc"; |
| 548 |
reg = <0x40d02000 0x4>, |
| 549 |
<0x40d02010 0x4>, |
| 550 |
<0x40d02014 0x4>; |
| 551 |
reg-names = "rev", "sysc", "syss"; |
| 552 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 553 |
<SYSC_IDLE_NO>, |
| 554 |
<SYSC_IDLE_SMART>; |
| 555 |
ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | |
| 556 |
SYSC_OMAP2_SOFTRESET | |
| 557 |
SYSC_OMAP2_AUTOIDLE)>; |
| 558 |
clocks = <&dsp1_clkctrl DRA7_DSP1_MMU0_DSP1_CLKCTRL 0>; |
| 559 |
clock-names = "fck"; |
| 560 |
resets = <&prm_dsp1 1>; |
| 561 |
reset-names = "rstctrl"; |
| 562 |
ranges = <0x0 0x40d02000 0x1000>; |
| 563 |
#size-cells = <1>; |
| 564 |
#address-cells = <1>; |
| 565 |
|
| 566 |
mmu1_dsp1: mmu@0 { |
| 567 |
compatible = "ti,dra7-dsp-iommu"; |
| 568 |
reg = <0x0 0x100>; |
| 569 |
interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>; |
| 570 |
#iommu-cells = <0>; |
| 571 |
ti,syscon-mmuconfig = <&dsp1_system 0x1>; |
| 572 |
}; |
| 573 |
}; |
| 574 |
|
| 575 |
target-module@58882000 { |
| 576 |
compatible = "ti,sysc-omap2", "ti,sysc"; |
| 577 |
reg = <0x58882000 0x4>, |
| 578 |
<0x58882010 0x4>, |
| 579 |
<0x58882014 0x4>; |
| 580 |
reg-names = "rev", "sysc", "syss"; |
| 581 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 582 |
<SYSC_IDLE_NO>, |
| 583 |
<SYSC_IDLE_SMART>; |
| 584 |
ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | |
| 585 |
SYSC_OMAP2_SOFTRESET | |
| 586 |
SYSC_OMAP2_AUTOIDLE)>; |
| 587 |
clocks = <&ipu1_clkctrl DRA7_IPU1_MMU_IPU1_CLKCTRL 0>; |
| 588 |
clock-names = "fck"; |
| 589 |
resets = <&prm_ipu 2>; |
| 590 |
reset-names = "rstctrl"; |
| 591 |
#address-cells = <1>; |
| 592 |
#size-cells = <1>; |
| 593 |
ranges = <0x0 0x58882000 0x100>; |
| 594 |
|
| 595 |
mmu_ipu1: mmu@0 { |
| 596 |
compatible = "ti,dra7-iommu"; |
| 597 |
reg = <0x0 0x100>; |
| 598 |
interrupts = <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>; |
| 599 |
#iommu-cells = <0>; |
| 600 |
ti,iommu-bus-err-back; |
| 601 |
}; |
| 602 |
}; |
| 603 |
|
| 604 |
target-module@55082000 { |
| 605 |
compatible = "ti,sysc-omap2", "ti,sysc"; |
| 606 |
reg = <0x55082000 0x4>, |
| 607 |
<0x55082010 0x4>, |
| 608 |
<0x55082014 0x4>; |
| 609 |
reg-names = "rev", "sysc", "syss"; |
| 610 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 611 |
<SYSC_IDLE_NO>, |
| 612 |
<SYSC_IDLE_SMART>; |
| 613 |
ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | |
| 614 |
SYSC_OMAP2_SOFTRESET | |
| 615 |
SYSC_OMAP2_AUTOIDLE)>; |
| 616 |
clocks = <&ipu2_clkctrl DRA7_IPU2_MMU_IPU2_CLKCTRL 0>; |
| 617 |
clock-names = "fck"; |
| 618 |
resets = <&prm_core 2>; |
| 619 |
reset-names = "rstctrl"; |
| 620 |
#address-cells = <1>; |
| 621 |
#size-cells = <1>; |
| 622 |
ranges = <0x0 0x55082000 0x100>; |
| 623 |
|
| 624 |
mmu_ipu2: mmu@0 { |
| 625 |
compatible = "ti,dra7-iommu"; |
| 626 |
reg = <0x0 0x100>; |
| 627 |
interrupts = <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>; |
| 628 |
#iommu-cells = <0>; |
| 629 |
ti,iommu-bus-err-back; |
| 630 |
}; |
| 631 |
}; |
| 632 |
|
| 633 |
abb_mpu: regulator-abb-mpu@4ae07ddc { |
| 634 |
compatible = "ti,abb-v3"; |
| 635 |
regulator-name = "abb_mpu"; |
| 636 |
#address-cells = <0>; |
| 637 |
#size-cells = <0>; |
| 638 |
clocks = <&sys_clkin1>; |
| 639 |
ti,settling-time = <50>; |
| 640 |
ti,clock-cycles = <16>; |
| 641 |
|
| 642 |
reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>, |
| 643 |
<0x4ae06014 0x4>, <0x4a003b20 0xc>, |
| 644 |
<0x4ae0c158 0x4>; |
| 645 |
reg-names = "setup-address", "control-address", |
| 646 |
"int-address", "efuse-address", |
| 647 |
"ldo-address"; |
| 648 |
ti,tranxdone-status-mask = <0x80>; |
| 649 |
/* LDOVBBMPU_FBB_MUX_CTRL */ |
| 650 |
ti,ldovbb-override-mask = <0x400>; |
| 651 |
/* LDOVBBMPU_FBB_VSET_OUT */ |
| 652 |
ti,ldovbb-vset-mask = <0x1F>; |
| 653 |
|
| 654 |
/* |
| 655 |
* NOTE: only FBB mode used but actual vset will |
| 656 |
* determine final biasing |
| 657 |
*/ |
| 658 |
ti,abb_info = < |
| 659 |
/*uV ABB efuse rbb_m fbb_m vset_m*/ |
| 660 |
1060000 0 0x0 0 0x02000000 0x01F00000 |
| 661 |
1160000 0 0x4 0 0x02000000 0x01F00000 |
| 662 |
1210000 0 0x8 0 0x02000000 0x01F00000 |
| 663 |
>; |
| 664 |
}; |
| 665 |
|
| 666 |
abb_ivahd: regulator-abb-ivahd@4ae07e34 { |
| 667 |
compatible = "ti,abb-v3"; |
| 668 |
regulator-name = "abb_ivahd"; |
| 669 |
#address-cells = <0>; |
| 670 |
#size-cells = <0>; |
| 671 |
clocks = <&sys_clkin1>; |
| 672 |
ti,settling-time = <50>; |
| 673 |
ti,clock-cycles = <16>; |
| 674 |
|
| 675 |
reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>, |
| 676 |
<0x4ae06010 0x4>, <0x4a0025cc 0xc>, |
| 677 |
<0x4a002470 0x4>; |
| 678 |
reg-names = "setup-address", "control-address", |
| 679 |
"int-address", "efuse-address", |
| 680 |
"ldo-address"; |
| 681 |
ti,tranxdone-status-mask = <0x40000000>; |
| 682 |
/* LDOVBBIVA_FBB_MUX_CTRL */ |
| 683 |
ti,ldovbb-override-mask = <0x400>; |
| 684 |
/* LDOVBBIVA_FBB_VSET_OUT */ |
| 685 |
ti,ldovbb-vset-mask = <0x1F>; |
| 686 |
|
| 687 |
/* |
| 688 |
* NOTE: only FBB mode used but actual vset will |
| 689 |
* determine final biasing |
| 690 |
*/ |
| 691 |
ti,abb_info = < |
| 692 |
/*uV ABB efuse rbb_m fbb_m vset_m*/ |
| 693 |
1055000 0 0x0 0 0x02000000 0x01F00000 |
| 694 |
1150000 0 0x4 0 0x02000000 0x01F00000 |
| 695 |
1250000 0 0x8 0 0x02000000 0x01F00000 |
| 696 |
>; |
| 697 |
}; |
| 698 |
|
| 699 |
abb_dspeve: regulator-abb-dspeve@4ae07e30 { |
| 700 |
compatible = "ti,abb-v3"; |
| 701 |
regulator-name = "abb_dspeve"; |
| 702 |
#address-cells = <0>; |
| 703 |
#size-cells = <0>; |
| 704 |
clocks = <&sys_clkin1>; |
| 705 |
ti,settling-time = <50>; |
| 706 |
ti,clock-cycles = <16>; |
| 707 |
|
| 708 |
reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>, |
| 709 |
<0x4ae06010 0x4>, <0x4a0025e0 0xc>, |
| 710 |
<0x4a00246c 0x4>; |
| 711 |
reg-names = "setup-address", "control-address", |
| 712 |
"int-address", "efuse-address", |
| 713 |
"ldo-address"; |
| 714 |
ti,tranxdone-status-mask = <0x20000000>; |
| 715 |
/* LDOVBBDSPEVE_FBB_MUX_CTRL */ |
| 716 |
ti,ldovbb-override-mask = <0x400>; |
| 717 |
/* LDOVBBDSPEVE_FBB_VSET_OUT */ |
| 718 |
ti,ldovbb-vset-mask = <0x1F>; |
| 719 |
|
| 720 |
/* |
| 721 |
* NOTE: only FBB mode used but actual vset will |
| 722 |
* determine final biasing |
| 723 |
*/ |
| 724 |
ti,abb_info = < |
| 725 |
/*uV ABB efuse rbb_m fbb_m vset_m*/ |
| 726 |
1055000 0 0x0 0 0x02000000 0x01F00000 |
| 727 |
1150000 0 0x4 0 0x02000000 0x01F00000 |
| 728 |
1250000 0 0x8 0 0x02000000 0x01F00000 |
| 729 |
>; |
| 730 |
}; |
| 731 |
|
| 732 |
abb_gpu: regulator-abb-gpu@4ae07de4 { |
| 733 |
compatible = "ti,abb-v3"; |
| 734 |
regulator-name = "abb_gpu"; |
| 735 |
#address-cells = <0>; |
| 736 |
#size-cells = <0>; |
| 737 |
clocks = <&sys_clkin1>; |
| 738 |
ti,settling-time = <50>; |
| 739 |
ti,clock-cycles = <16>; |
| 740 |
|
| 741 |
reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>, |
| 742 |
<0x4ae06010 0x4>, <0x4a003b08 0xc>, |
| 743 |
<0x4ae0c154 0x4>; |
| 744 |
reg-names = "setup-address", "control-address", |
| 745 |
"int-address", "efuse-address", |
| 746 |
"ldo-address"; |
| 747 |
ti,tranxdone-status-mask = <0x10000000>; |
| 748 |
/* LDOVBBGPU_FBB_MUX_CTRL */ |
| 749 |
ti,ldovbb-override-mask = <0x400>; |
| 750 |
/* LDOVBBGPU_FBB_VSET_OUT */ |
| 751 |
ti,ldovbb-vset-mask = <0x1F>; |
| 752 |
|
| 753 |
/* |
| 754 |
* NOTE: only FBB mode used but actual vset will |
| 755 |
* determine final biasing |
| 756 |
*/ |
| 757 |
ti,abb_info = < |
| 758 |
/*uV ABB efuse rbb_m fbb_m vset_m*/ |
| 759 |
1090000 0 0x0 0 0x02000000 0x01F00000 |
| 760 |
1210000 0 0x4 0 0x02000000 0x01F00000 |
| 761 |
1280000 0 0x8 0 0x02000000 0x01F00000 |
| 762 |
>; |
| 763 |
}; |
| 764 |
|
| 765 |
target-module@4b300000 { |
| 766 |
compatible = "ti,sysc-omap4", "ti,sysc"; |
| 767 |
reg = <0x4b300000 0x4>, |
| 768 |
<0x4b300010 0x4>; |
| 769 |
reg-names = "rev", "sysc"; |
| 770 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 771 |
<SYSC_IDLE_NO>, |
| 772 |
<SYSC_IDLE_SMART>, |
| 773 |
<SYSC_IDLE_SMART_WKUP>; |
| 774 |
clocks = <&l4per2_clkctrl DRA7_L4PER2_QSPI_CLKCTRL 0>; |
| 775 |
clock-names = "fck"; |
| 776 |
#address-cells = <1>; |
| 777 |
#size-cells = <1>; |
| 778 |
ranges = <0x0 0x4b300000 0x1000>, |
| 779 |
<0x5c000000 0x5c000000 0x4000000>; |
| 780 |
|
| 781 |
qspi: spi@0 { |
| 782 |
compatible = "ti,dra7xxx-qspi"; |
| 783 |
reg = <0 0x100>, |
| 784 |
<0x5c000000 0x4000000>; |
| 785 |
reg-names = "qspi_base", "qspi_mmap"; |
| 786 |
syscon-chipselects = <&scm_conf 0x558>; |
| 787 |
#address-cells = <1>; |
| 788 |
#size-cells = <0>; |
| 789 |
clocks = <&l4per2_clkctrl DRA7_L4PER2_QSPI_CLKCTRL 25>; |
| 790 |
clock-names = "fck"; |
| 791 |
num-cs = <4>; |
| 792 |
interrupts = <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>; |
| 793 |
status = "disabled"; |
| 794 |
}; |
| 795 |
}; |
| 796 |
|
| 797 |
/* OCP2SCP1 */ |
| 798 |
/* IRQ for DWC3_3 and DWC3_4 need IRQ crossbar */ |
| 799 |
|
| 800 |
target-module@50000000 { |
| 801 |
compatible = "ti,sysc-omap2", "ti,sysc"; |
| 802 |
reg = <0x50000000 4>, |
| 803 |
<0x50000010 4>, |
| 804 |
<0x50000014 4>; |
| 805 |
reg-names = "rev", "sysc", "syss"; |
| 806 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 807 |
<SYSC_IDLE_NO>, |
| 808 |
<SYSC_IDLE_SMART>; |
| 809 |
ti,syss-mask = <1>; |
| 810 |
clocks = <&l3main1_clkctrl DRA7_L3MAIN1_GPMC_CLKCTRL 0>; |
| 811 |
clock-names = "fck"; |
| 812 |
#address-cells = <1>; |
| 813 |
#size-cells = <1>; |
| 814 |
ranges = <0x50000000 0x50000000 0x00001000>, /* regs */ |
| 815 |
<0x00000000 0x00000000 0x40000000>; /* data */ |
| 816 |
|
| 817 |
gpmc: gpmc@50000000 { |
| 818 |
compatible = "ti,am3352-gpmc"; |
| 819 |
reg = <0x50000000 0x37c>; /* device IO registers */ |
| 820 |
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; |
| 821 |
dmas = <&edma_xbar 4 0>; |
| 822 |
dma-names = "rxtx"; |
| 823 |
gpmc,num-cs = <8>; |
| 824 |
gpmc,num-waitpins = <2>; |
| 825 |
#address-cells = <2>; |
| 826 |
#size-cells = <1>; |
| 827 |
interrupt-controller; |
| 828 |
#interrupt-cells = <2>; |
| 829 |
gpio-controller; |
| 830 |
#gpio-cells = <2>; |
| 831 |
status = "disabled"; |
| 832 |
}; |
| 833 |
}; |
| 834 |
|
| 835 |
target-module@56000000 { |
| 836 |
compatible = "ti,sysc-omap4", "ti,sysc"; |
| 837 |
reg = <0x5600fe00 0x4>, |
| 838 |
<0x5600fe10 0x4>; |
| 839 |
reg-names = "rev", "sysc"; |
| 840 |
ti,sysc-midle = <SYSC_IDLE_FORCE>, |
| 841 |
<SYSC_IDLE_NO>, |
| 842 |
<SYSC_IDLE_SMART>; |
| 843 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 844 |
<SYSC_IDLE_NO>, |
| 845 |
<SYSC_IDLE_SMART>, |
| 846 |
<SYSC_IDLE_SMART_WKUP>; |
| 847 |
clocks = <&gpu_clkctrl DRA7_GPU_CLKCTRL 0>; |
| 848 |
clock-names = "fck"; |
| 849 |
#address-cells = <1>; |
| 850 |
#size-cells = <1>; |
| 851 |
ranges = <0 0x56000000 0x2000000>; |
| 852 |
|
| 853 |
gpu@0 { |
| 854 |
compatible = "ti,am5728-gpu", "img,powervr-sgx544"; |
| 855 |
reg = <0x0 0x10000>; /* 64kB */ |
| 856 |
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; |
| 857 |
}; |
| 858 |
}; |
| 859 |
|
| 860 |
crossbar_mpu: crossbar@4a002a48 { |
| 861 |
compatible = "ti,irq-crossbar"; |
| 862 |
reg = <0x4a002a48 0x130>; |
| 863 |
interrupt-controller; |
| 864 |
interrupt-parent = <&wakeupgen>; |
| 865 |
#interrupt-cells = <3>; |
| 866 |
ti,max-irqs = <160>; |
| 867 |
ti,max-crossbar-sources = <MAX_SOURCES>; |
| 868 |
ti,reg-size = <2>; |
| 869 |
ti,irqs-reserved = <0 1 2 3 5 6 131 132>; |
| 870 |
ti,irqs-skip = <10 133 139 140>; |
| 871 |
ti,irqs-safe-map = <0>; |
| 872 |
}; |
| 873 |
|
| 874 |
target-module@58000000 { |
| 875 |
compatible = "ti,sysc-omap2", "ti,sysc"; |
| 876 |
reg = <0x58000000 4>, |
| 877 |
<0x58000014 4>; |
| 878 |
reg-names = "rev", "syss"; |
| 879 |
ti,syss-mask = <1>; |
| 880 |
clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 0>, |
| 881 |
<&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 9>, |
| 882 |
<&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 10>, |
| 883 |
<&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 11>; |
| 884 |
clock-names = "fck", "hdmi_clk", "sys_clk", "tv_clk"; |
| 885 |
#address-cells = <1>; |
| 886 |
#size-cells = <1>; |
| 887 |
ranges = <0 0x58000000 0x800000>; |
| 888 |
|
| 889 |
dss: dss@0 { |
| 890 |
compatible = "ti,dra7-dss"; |
| 891 |
/* 'reg' defined in dra72x.dtsi and dra74x.dtsi */ |
| 892 |
/* 'clocks' defined in dra72x.dtsi and dra74x.dtsi */ |
| 893 |
status = "disabled"; |
| 894 |
/* CTRL_CORE_DSS_PLL_CONTROL */ |
| 895 |
syscon-pll-ctrl = <&scm_conf 0x538>; |
| 896 |
#address-cells = <1>; |
| 897 |
#size-cells = <1>; |
| 898 |
ranges = <0 0 0x800000>; |
| 899 |
|
| 900 |
target-module@1000 { |
| 901 |
compatible = "ti,sysc-omap2", "ti,sysc"; |
| 902 |
reg = <0x1000 0x4>, |
| 903 |
<0x1010 0x4>, |
| 904 |
<0x1014 0x4>; |
| 905 |
reg-names = "rev", "sysc", "syss"; |
| 906 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 907 |
<SYSC_IDLE_NO>, |
| 908 |
<SYSC_IDLE_SMART>; |
| 909 |
ti,sysc-midle = <SYSC_IDLE_FORCE>, |
| 910 |
<SYSC_IDLE_NO>, |
| 911 |
<SYSC_IDLE_SMART>; |
| 912 |
ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | |
| 913 |
SYSC_OMAP2_ENAWAKEUP | |
| 914 |
SYSC_OMAP2_SOFTRESET | |
| 915 |
SYSC_OMAP2_AUTOIDLE)>; |
| 916 |
ti,syss-mask = <1>; |
| 917 |
clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>; |
| 918 |
clock-names = "fck"; |
| 919 |
#address-cells = <1>; |
| 920 |
#size-cells = <1>; |
| 921 |
ranges = <0 0x1000 0x1000>; |
| 922 |
|
| 923 |
dispc@0 { |
| 924 |
compatible = "ti,dra7-dispc"; |
| 925 |
reg = <0 0x1000>; |
| 926 |
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; |
| 927 |
clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>; |
| 928 |
clock-names = "fck"; |
| 929 |
/* CTRL_CORE_SMA_SW_1 */ |
| 930 |
syscon-pol = <&scm_conf 0x534>; |
| 931 |
}; |
| 932 |
}; |
| 933 |
|
| 934 |
target-module@40000 { |
| 935 |
compatible = "ti,sysc-omap4", "ti,sysc"; |
| 936 |
reg = <0x40000 0x4>, |
| 937 |
<0x40010 0x4>; |
| 938 |
reg-names = "rev", "sysc"; |
| 939 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 940 |
<SYSC_IDLE_NO>, |
| 941 |
<SYSC_IDLE_SMART>, |
| 942 |
<SYSC_IDLE_SMART_WKUP>; |
| 943 |
ti,sysc-mask = <(SYSC_OMAP4_SOFTRESET)>; |
| 944 |
clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 9>, |
| 945 |
<&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>; |
| 946 |
clock-names = "fck", "dss_clk"; |
| 947 |
#address-cells = <1>; |
| 948 |
#size-cells = <1>; |
| 949 |
ranges = <0 0x40000 0x40000>; |
| 950 |
|
| 951 |
hdmi: encoder@0 { |
| 952 |
compatible = "ti,dra7-hdmi"; |
| 953 |
reg = <0 0x200>, |
| 954 |
<0x200 0x80>, |
| 955 |
<0x300 0x80>, |
| 956 |
<0x20000 0x19000>; |
| 957 |
reg-names = "wp", "pll", "phy", "core"; |
| 958 |
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| 959 |
status = "disabled"; |
| 960 |
clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 9>, |
| 961 |
<&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 10>; |
| 962 |
clock-names = "fck", "sys_clk"; |
| 963 |
dmas = <&sdma_xbar 76>; |
| 964 |
dma-names = "audio_tx"; |
| 965 |
}; |
| 966 |
}; |
| 967 |
}; |
| 968 |
}; |
| 969 |
|
| 970 |
target-module@59000000 { |
| 971 |
compatible = "ti,sysc-omap4", "ti,sysc"; |
| 972 |
reg = <0x59000020 0x4>; |
| 973 |
reg-names = "rev"; |
| 974 |
clocks = <&dss_clkctrl DRA7_DSS_BB2D_CLKCTRL 0>; |
| 975 |
clock-names = "fck"; |
| 976 |
#address-cells = <1>; |
| 977 |
#size-cells = <1>; |
| 978 |
ranges = <0x0 0x59000000 0x1000>; |
| 979 |
|
| 980 |
bb2d: gpu@0 { |
| 981 |
compatible = "vivante,gc"; |
| 982 |
reg = <0x0 0x700>; |
| 983 |
interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; |
| 984 |
clocks = <&dss_clkctrl DRA7_DSS_BB2D_CLKCTRL 0>; |
| 985 |
clock-names = "core"; |
| 986 |
}; |
| 987 |
}; |
| 988 |
|
| 989 |
aes1_target: target-module@4b500000 { |
| 990 |
compatible = "ti,sysc-omap2", "ti,sysc"; |
| 991 |
reg = <0x4b500080 0x4>, |
| 992 |
<0x4b500084 0x4>, |
| 993 |
<0x4b500088 0x4>; |
| 994 |
reg-names = "rev", "sysc", "syss"; |
| 995 |
ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET | |
| 996 |
SYSC_OMAP2_AUTOIDLE)>; |
| 997 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 998 |
<SYSC_IDLE_NO>, |
| 999 |
<SYSC_IDLE_SMART>, |
| 1000 |
<SYSC_IDLE_SMART_WKUP>; |
| 1001 |
ti,syss-mask = <1>; |
| 1002 |
/* Domains (P, C): per_pwrdm, l4sec_clkdm */ |
| 1003 |
clocks = <&l4sec_clkctrl DRA7_L4SEC_AES1_CLKCTRL 0>; |
| 1004 |
clock-names = "fck"; |
| 1005 |
#address-cells = <1>; |
| 1006 |
#size-cells = <1>; |
| 1007 |
ranges = <0x0 0x4b500000 0x1000>; |
| 1008 |
|
| 1009 |
aes1: aes@0 { |
| 1010 |
compatible = "ti,omap4-aes"; |
| 1011 |
reg = <0 0xa0>; |
| 1012 |
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; |
| 1013 |
dmas = <&edma_xbar 111 0>, <&edma_xbar 110 0>; |
| 1014 |
dma-names = "tx", "rx"; |
| 1015 |
clocks = <&l3_iclk_div>; |
| 1016 |
clock-names = "fck"; |
| 1017 |
}; |
| 1018 |
}; |
| 1019 |
|
| 1020 |
aes2_target: target-module@4b700000 { |
| 1021 |
compatible = "ti,sysc-omap2", "ti,sysc"; |
| 1022 |
reg = <0x4b700080 0x4>, |
| 1023 |
<0x4b700084 0x4>, |
| 1024 |
<0x4b700088 0x4>; |
| 1025 |
reg-names = "rev", "sysc", "syss"; |
| 1026 |
ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET | |
| 1027 |
SYSC_OMAP2_AUTOIDLE)>; |
| 1028 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 1029 |
<SYSC_IDLE_NO>, |
| 1030 |
<SYSC_IDLE_SMART>, |
| 1031 |
<SYSC_IDLE_SMART_WKUP>; |
| 1032 |
ti,syss-mask = <1>; |
| 1033 |
/* Domains (P, C): per_pwrdm, l4sec_clkdm */ |
| 1034 |
clocks = <&l4sec_clkctrl DRA7_L4SEC_AES2_CLKCTRL 0>; |
| 1035 |
clock-names = "fck"; |
| 1036 |
#address-cells = <1>; |
| 1037 |
#size-cells = <1>; |
| 1038 |
ranges = <0x0 0x4b700000 0x1000>; |
| 1039 |
|
| 1040 |
aes2: aes@0 { |
| 1041 |
compatible = "ti,omap4-aes"; |
| 1042 |
reg = <0 0xa0>; |
| 1043 |
interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; |
| 1044 |
dmas = <&edma_xbar 114 0>, <&edma_xbar 113 0>; |
| 1045 |
dma-names = "tx", "rx"; |
| 1046 |
clocks = <&l3_iclk_div>; |
| 1047 |
clock-names = "fck"; |
| 1048 |
}; |
| 1049 |
}; |
| 1050 |
|
| 1051 |
sham1_target: target-module@4b101000 { |
| 1052 |
compatible = "ti,sysc-omap3-sham", "ti,sysc"; |
| 1053 |
reg = <0x4b101100 0x4>, |
| 1054 |
<0x4b101110 0x4>, |
| 1055 |
<0x4b101114 0x4>; |
| 1056 |
reg-names = "rev", "sysc", "syss"; |
| 1057 |
ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET | |
| 1058 |
SYSC_OMAP2_AUTOIDLE)>; |
| 1059 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 1060 |
<SYSC_IDLE_NO>, |
| 1061 |
<SYSC_IDLE_SMART>; |
| 1062 |
ti,syss-mask = <1>; |
| 1063 |
/* Domains (P, C): l4per_pwrdm, l4sec_clkdm */ |
| 1064 |
clocks = <&l4sec_clkctrl DRA7_L4SEC_SHAM_CLKCTRL 0>; |
| 1065 |
clock-names = "fck"; |
| 1066 |
#address-cells = <1>; |
| 1067 |
#size-cells = <1>; |
| 1068 |
ranges = <0x0 0x4b101000 0x1000>; |
| 1069 |
|
| 1070 |
sham1: sham@0 { |
| 1071 |
compatible = "ti,omap5-sham"; |
| 1072 |
reg = <0 0x300>; |
| 1073 |
interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; |
| 1074 |
dmas = <&edma_xbar 119 0>; |
| 1075 |
dma-names = "rx"; |
| 1076 |
clocks = <&l3_iclk_div>; |
| 1077 |
clock-names = "fck"; |
| 1078 |
}; |
| 1079 |
}; |
| 1080 |
|
| 1081 |
sham2_target: target-module@42701000 { |
| 1082 |
compatible = "ti,sysc-omap3-sham", "ti,sysc"; |
| 1083 |
reg = <0x42701100 0x4>, |
| 1084 |
<0x42701110 0x4>, |
| 1085 |
<0x42701114 0x4>; |
| 1086 |
reg-names = "rev", "sysc", "syss"; |
| 1087 |
ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET | |
| 1088 |
SYSC_OMAP2_AUTOIDLE)>; |
| 1089 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 1090 |
<SYSC_IDLE_NO>, |
| 1091 |
<SYSC_IDLE_SMART>; |
| 1092 |
ti,syss-mask = <1>; |
| 1093 |
/* Domains (P, C): l4per_pwrdm, l4sec_clkdm */ |
| 1094 |
clocks = <&l4sec_clkctrl DRA7_L4SEC_SHAM2_CLKCTRL 0>; |
| 1095 |
clock-names = "fck"; |
| 1096 |
#address-cells = <1>; |
| 1097 |
#size-cells = <1>; |
| 1098 |
ranges = <0x0 0x42701000 0x1000>; |
| 1099 |
|
| 1100 |
sham2: sham@0 { |
| 1101 |
compatible = "ti,omap5-sham"; |
| 1102 |
reg = <0 0x300>; |
| 1103 |
interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>; |
| 1104 |
dmas = <&edma_xbar 165 0>; |
| 1105 |
dma-names = "rx"; |
| 1106 |
clocks = <&l3_iclk_div>; |
| 1107 |
clock-names = "fck"; |
| 1108 |
}; |
| 1109 |
}; |
| 1110 |
|
| 1111 |
iva_hd_target: target-module@5a000000 { |
| 1112 |
compatible = "ti,sysc-omap4", "ti,sysc"; |
| 1113 |
reg = <0x5a05a400 0x4>, |
| 1114 |
<0x5a05a410 0x4>; |
| 1115 |
reg-names = "rev", "sysc"; |
| 1116 |
ti,sysc-midle = <SYSC_IDLE_FORCE>, |
| 1117 |
<SYSC_IDLE_NO>, |
| 1118 |
<SYSC_IDLE_SMART>; |
| 1119 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 1120 |
<SYSC_IDLE_NO>, |
| 1121 |
<SYSC_IDLE_SMART>; |
| 1122 |
power-domains = <&prm_iva>; |
| 1123 |
resets = <&prm_iva 2>; |
| 1124 |
reset-names = "rstctrl"; |
| 1125 |
clocks = <&iva_clkctrl DRA7_IVA_CLKCTRL 0>; |
| 1126 |
clock-names = "fck"; |
| 1127 |
#address-cells = <1>; |
| 1128 |
#size-cells = <1>; |
| 1129 |
ranges = <0x5a000000 0x5a000000 0x1000000>, |
| 1130 |
<0x5b000000 0x5b000000 0x1000000>; |
| 1131 |
|
| 1132 |
iva { |
| 1133 |
compatible = "ti,ivahd"; |
| 1134 |
}; |
| 1135 |
}; |
| 1136 |
|
| 1137 |
opp_supply_mpu: opp-supply@4a003b20 { |
| 1138 |
compatible = "ti,omap5-opp-supply"; |
| 1139 |
reg = <0x4a003b20 0xc>; |
| 1140 |
ti,efuse-settings = < |
| 1141 |
/* uV offset */ |
| 1142 |
1060000 0x0 |
| 1143 |
1160000 0x4 |
| 1144 |
1210000 0x8 |
| 1145 |
>; |
| 1146 |
ti,absolute-max-voltage-uv = <1500000>; |
| 1147 |
}; |
| 1148 |
|
| 1149 |
}; |
| 1150 |
|
| 1151 |
thermal_zones: thermal-zones { |
| 1152 |
#include "omap4-cpu-thermal.dtsi" |
| 1153 |
#include "omap5-gpu-thermal.dtsi" |
| 1154 |
#include "omap5-core-thermal.dtsi" |
| 1155 |
#include "dra7-dspeve-thermal.dtsi" |
| 1156 |
#include "dra7-iva-thermal.dtsi" |
| 1157 |
}; |
| 1158 |
|
| 1159 |
}; |
| 1160 |
|
| 1161 |
&cpu_thermal { |
| 1162 |
polling-delay = <500>; /* milliseconds */ |
| 1163 |
coefficients = <0 2000>; |
| 1164 |
}; |
| 1165 |
|
| 1166 |
&gpu_thermal { |
| 1167 |
coefficients = <0 2000>; |
| 1168 |
}; |
| 1169 |
|
| 1170 |
&core_thermal { |
| 1171 |
coefficients = <0 2000>; |
| 1172 |
}; |
| 1173 |
|
| 1174 |
&dspeve_thermal { |
| 1175 |
coefficients = <0 2000>; |
| 1176 |
}; |
| 1177 |
|
| 1178 |
&iva_thermal { |
| 1179 |
coefficients = <0 2000>; |
| 1180 |
}; |
| 1181 |
|
| 1182 |
&cpu_crit { |
| 1183 |
temperature = <120000>; /* milli Celsius */ |
| 1184 |
}; |
| 1185 |
|
| 1186 |
&core_crit { |
| 1187 |
temperature = <120000>; /* milli Celsius */ |
| 1188 |
}; |
| 1189 |
|
| 1190 |
&gpu_crit { |
| 1191 |
temperature = <120000>; /* milli Celsius */ |
| 1192 |
}; |
| 1193 |
|
| 1194 |
&dspeve_crit { |
| 1195 |
temperature = <120000>; /* milli Celsius */ |
| 1196 |
}; |
| 1197 |
|
| 1198 |
&iva_crit { |
| 1199 |
temperature = <120000>; /* milli Celsius */ |
| 1200 |
}; |
| 1201 |
|
| 1202 |
#include "dra7-l4.dtsi" |
| 1203 |
#include "dra7xx-clocks.dtsi" |
| 1204 |
|
| 1205 |
&prm { |
| 1206 |
prm_mpu: prm@300 { |
| 1207 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1208 |
reg = <0x300 0x100>; |
| 1209 |
#power-domain-cells = <0>; |
| 1210 |
}; |
| 1211 |
|
| 1212 |
prm_dsp1: prm@400 { |
| 1213 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1214 |
reg = <0x400 0x100>; |
| 1215 |
#reset-cells = <1>; |
| 1216 |
#power-domain-cells = <0>; |
| 1217 |
}; |
| 1218 |
|
| 1219 |
prm_ipu: prm@500 { |
| 1220 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1221 |
reg = <0x500 0x100>; |
| 1222 |
#reset-cells = <1>; |
| 1223 |
#power-domain-cells = <0>; |
| 1224 |
}; |
| 1225 |
|
| 1226 |
prm_coreaon: prm@628 { |
| 1227 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1228 |
reg = <0x628 0xd8>; |
| 1229 |
#power-domain-cells = <0>; |
| 1230 |
}; |
| 1231 |
|
| 1232 |
prm_core: prm@700 { |
| 1233 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1234 |
reg = <0x700 0x100>; |
| 1235 |
#reset-cells = <1>; |
| 1236 |
#power-domain-cells = <0>; |
| 1237 |
}; |
| 1238 |
|
| 1239 |
prm_iva: prm@f00 { |
| 1240 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1241 |
reg = <0xf00 0x100>; |
| 1242 |
#reset-cells = <1>; |
| 1243 |
#power-domain-cells = <0>; |
| 1244 |
}; |
| 1245 |
|
| 1246 |
prm_cam: prm@1000 { |
| 1247 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1248 |
reg = <0x1000 0x100>; |
| 1249 |
#power-domain-cells = <0>; |
| 1250 |
}; |
| 1251 |
|
| 1252 |
prm_dss: prm@1100 { |
| 1253 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1254 |
reg = <0x1100 0x100>; |
| 1255 |
#power-domain-cells = <0>; |
| 1256 |
}; |
| 1257 |
|
| 1258 |
prm_gpu: prm@1200 { |
| 1259 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1260 |
reg = <0x1200 0x100>; |
| 1261 |
#power-domain-cells = <0>; |
| 1262 |
}; |
| 1263 |
|
| 1264 |
prm_l3init: prm@1300 { |
| 1265 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1266 |
reg = <0x1300 0x100>; |
| 1267 |
#reset-cells = <1>; |
| 1268 |
#power-domain-cells = <0>; |
| 1269 |
}; |
| 1270 |
|
| 1271 |
prm_l4per: prm@1400 { |
| 1272 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1273 |
reg = <0x1400 0x100>; |
| 1274 |
#power-domain-cells = <0>; |
| 1275 |
}; |
| 1276 |
|
| 1277 |
prm_custefuse: prm@1600 { |
| 1278 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1279 |
reg = <0x1600 0x100>; |
| 1280 |
#power-domain-cells = <0>; |
| 1281 |
}; |
| 1282 |
|
| 1283 |
prm_wkupaon: prm@1724 { |
| 1284 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1285 |
reg = <0x1724 0x100>; |
| 1286 |
#power-domain-cells = <0>; |
| 1287 |
}; |
| 1288 |
|
| 1289 |
prm_dsp2: prm@1b00 { |
| 1290 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1291 |
reg = <0x1b00 0x40>; |
| 1292 |
#reset-cells = <1>; |
| 1293 |
#power-domain-cells = <0>; |
| 1294 |
}; |
| 1295 |
|
| 1296 |
prm_eve1: prm@1b40 { |
| 1297 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1298 |
reg = <0x1b40 0x40>; |
| 1299 |
#power-domain-cells = <0>; |
| 1300 |
}; |
| 1301 |
|
| 1302 |
prm_eve2: prm@1b80 { |
| 1303 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1304 |
reg = <0x1b80 0x40>; |
| 1305 |
#power-domain-cells = <0>; |
| 1306 |
}; |
| 1307 |
|
| 1308 |
prm_eve3: prm@1bc0 { |
| 1309 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1310 |
reg = <0x1bc0 0x40>; |
| 1311 |
#power-domain-cells = <0>; |
| 1312 |
}; |
| 1313 |
|
| 1314 |
prm_eve4: prm@1c00 { |
| 1315 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1316 |
reg = <0x1c00 0x60>; |
| 1317 |
#power-domain-cells = <0>; |
| 1318 |
}; |
| 1319 |
|
| 1320 |
prm_rtc: prm@1c60 { |
| 1321 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1322 |
reg = <0x1c60 0x20>; |
| 1323 |
#power-domain-cells = <0>; |
| 1324 |
}; |
| 1325 |
|
| 1326 |
prm_vpe: prm@1c80 { |
| 1327 |
compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst"; |
| 1328 |
reg = <0x1c80 0x80>; |
| 1329 |
#power-domain-cells = <0>; |
| 1330 |
}; |
| 1331 |
}; |
| 1332 |
|
| 1333 |
/* Preferred always-on timer for clockevent */ |
| 1334 |
&timer1_target { |
| 1335 |
ti,no-reset-on-init; |
| 1336 |
ti,no-idle; |
| 1337 |
timer@0 { |
| 1338 |
assigned-clocks = <&wkupaon_clkctrl DRA7_WKUPAON_TIMER1_CLKCTRL 24>; |
| 1339 |
assigned-clock-parents = <&sys_32k_ck>; |
| 1340 |
}; |
| 1341 |
}; |
| 1342 |
|
| 1343 |
/* Local timers, see ARM architected timer wrap erratum i940 */ |
| 1344 |
&timer15_target { |
| 1345 |
ti,no-reset-on-init; |
| 1346 |
ti,no-idle; |
| 1347 |
timer@0 { |
| 1348 |
assigned-clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER15_CLKCTRL 24>; |
| 1349 |
assigned-clock-parents = <&timer_sys_clk_div>; |
| 1350 |
}; |
| 1351 |
}; |
| 1352 |
|
| 1353 |
&timer16_target { |
| 1354 |
ti,no-reset-on-init; |
| 1355 |
ti,no-idle; |
| 1356 |
timer@0 { |
| 1357 |
assigned-clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER16_CLKCTRL 24>; |
| 1358 |
assigned-clock-parents = <&timer_sys_clk_div>; |
| 1359 |
}; |
| 1360 |
}; |