| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Copyright (C) 2014-2016 Texas Instruments Incorporated - https://www.ti.com/ |
| 4 |
*/ |
| 5 |
/dts-v1/; |
| 6 |
|
| 7 |
#include "dra72x.dtsi" |
| 8 |
#include "dra7-ipu-dsp-common.dtsi" |
| 9 |
#include <dt-bindings/gpio/gpio.h> |
| 10 |
#include <dt-bindings/clock/ti-dra7-atl.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7"; |
| 14 |
|
| 15 |
aliases { |
| 16 |
display0 = &hdmi0; |
| 17 |
}; |
| 18 |
|
| 19 |
chosen { |
| 20 |
stdout-path = &uart1; |
| 21 |
}; |
| 22 |
|
| 23 |
evm_12v0: fixedregulator-evm12v0 { |
| 24 |
/* main supply */ |
| 25 |
compatible = "regulator-fixed"; |
| 26 |
regulator-name = "evm_12v0"; |
| 27 |
regulator-min-microvolt = <12000000>; |
| 28 |
regulator-max-microvolt = <12000000>; |
| 29 |
regulator-always-on; |
| 30 |
regulator-boot-on; |
| 31 |
}; |
| 32 |
|
| 33 |
evm_5v0: fixedregulator-evm5v0 { |
| 34 |
/* Output 1 of TPS43351QDAPRQ1 on dra72-evm */ |
| 35 |
/* Output 1 of LM5140QRWGTQ1 on dra71-evm */ |
| 36 |
compatible = "regulator-fixed"; |
| 37 |
regulator-name = "evm_5v0"; |
| 38 |
regulator-min-microvolt = <5000000>; |
| 39 |
regulator-max-microvolt = <5000000>; |
| 40 |
vin-supply = <&evm_12v0>; |
| 41 |
regulator-always-on; |
| 42 |
regulator-boot-on; |
| 43 |
}; |
| 44 |
|
| 45 |
evm_3v6: fixedregulator-evm_3v6 { |
| 46 |
compatible = "regulator-fixed"; |
| 47 |
regulator-name = "evm_3v6"; |
| 48 |
regulator-min-microvolt = <3600000>; |
| 49 |
regulator-max-microvolt = <3600000>; |
| 50 |
vin-supply = <&evm_5v0>; |
| 51 |
regulator-always-on; |
| 52 |
regulator-boot-on; |
| 53 |
}; |
| 54 |
|
| 55 |
vsys_3v3: fixedregulator-vsys3v3 { |
| 56 |
/* Output 2 of TPS43351QDAPRQ1 on dra72-evm */ |
| 57 |
/* Output 2 of LM5140QRWGTQ1 on dra71-evm */ |
| 58 |
compatible = "regulator-fixed"; |
| 59 |
regulator-name = "vsys_3v3"; |
| 60 |
regulator-min-microvolt = <3300000>; |
| 61 |
regulator-max-microvolt = <3300000>; |
| 62 |
vin-supply = <&evm_12v0>; |
| 63 |
regulator-always-on; |
| 64 |
regulator-boot-on; |
| 65 |
}; |
| 66 |
|
| 67 |
evm_3v3_sw: fixedregulator-evm_3v3 { |
| 68 |
/* TPS22965DSG */ |
| 69 |
compatible = "regulator-fixed"; |
| 70 |
regulator-name = "evm_3v3"; |
| 71 |
regulator-min-microvolt = <3300000>; |
| 72 |
regulator-max-microvolt = <3300000>; |
| 73 |
vin-supply = <&vsys_3v3>; |
| 74 |
regulator-always-on; |
| 75 |
regulator-boot-on; |
| 76 |
}; |
| 77 |
|
| 78 |
aic_dvdd: fixedregulator-aic_dvdd { |
| 79 |
/* TPS77018DBVT */ |
| 80 |
compatible = "regulator-fixed"; |
| 81 |
regulator-name = "aic_dvdd"; |
| 82 |
vin-supply = <&evm_3v3_sw>; |
| 83 |
regulator-min-microvolt = <1800000>; |
| 84 |
regulator-max-microvolt = <1800000>; |
| 85 |
}; |
| 86 |
|
| 87 |
evm_3v3_sd: fixedregulator-sd { |
| 88 |
compatible = "regulator-fixed"; |
| 89 |
regulator-name = "evm_3v3_sd"; |
| 90 |
regulator-min-microvolt = <3300000>; |
| 91 |
regulator-max-microvolt = <3300000>; |
| 92 |
vin-supply = <&evm_3v3_sw>; |
| 93 |
enable-active-high; |
| 94 |
gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>; |
| 95 |
}; |
| 96 |
|
| 97 |
extcon_usb1: extcon_usb1 { |
| 98 |
compatible = "linux,extcon-usb-gpio"; |
| 99 |
id-gpios = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>; |
| 100 |
}; |
| 101 |
|
| 102 |
extcon_usb2: extcon_usb2 { |
| 103 |
compatible = "linux,extcon-usb-gpio"; |
| 104 |
id-gpios = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>; |
| 105 |
}; |
| 106 |
|
| 107 |
hdmi0: connector { |
| 108 |
compatible = "hdmi-connector"; |
| 109 |
label = "hdmi"; |
| 110 |
|
| 111 |
type = "a"; |
| 112 |
|
| 113 |
port { |
| 114 |
hdmi_connector_in: endpoint { |
| 115 |
remote-endpoint = <&tpd12s015_out>; |
| 116 |
}; |
| 117 |
}; |
| 118 |
}; |
| 119 |
|
| 120 |
tpd12s015: encoder { |
| 121 |
compatible = "ti,tpd12s015"; |
| 122 |
|
| 123 |
gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>, /* P4, CT CP HPD */ |
| 124 |
<&pcf_hdmi 5 GPIO_ACTIVE_HIGH>, /* P5, LS OE */ |
| 125 |
<&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */ |
| 126 |
|
| 127 |
ports { |
| 128 |
#address-cells = <1>; |
| 129 |
#size-cells = <0>; |
| 130 |
|
| 131 |
port@0 { |
| 132 |
reg = <0>; |
| 133 |
|
| 134 |
tpd12s015_in: endpoint { |
| 135 |
remote-endpoint = <&hdmi_out>; |
| 136 |
}; |
| 137 |
}; |
| 138 |
|
| 139 |
port@1 { |
| 140 |
reg = <1>; |
| 141 |
|
| 142 |
tpd12s015_out: endpoint { |
| 143 |
remote-endpoint = <&hdmi_connector_in>; |
| 144 |
}; |
| 145 |
}; |
| 146 |
}; |
| 147 |
}; |
| 148 |
|
| 149 |
sound0: sound0 { |
| 150 |
compatible = "simple-audio-card"; |
| 151 |
simple-audio-card,name = "DRA7xx-EVM"; |
| 152 |
simple-audio-card,widgets = |
| 153 |
"Headphone", "Headphone Jack", |
| 154 |
"Line", "Line Out", |
| 155 |
"Microphone", "Mic Jack", |
| 156 |
"Line", "Line In"; |
| 157 |
simple-audio-card,routing = |
| 158 |
"Headphone Jack", "HPLOUT", |
| 159 |
"Headphone Jack", "HPROUT", |
| 160 |
"Line Out", "LLOUT", |
| 161 |
"Line Out", "RLOUT", |
| 162 |
"MIC3L", "Mic Jack", |
| 163 |
"MIC3R", "Mic Jack", |
| 164 |
"Mic Jack", "Mic Bias", |
| 165 |
"LINE1L", "Line In", |
| 166 |
"LINE1R", "Line In"; |
| 167 |
simple-audio-card,format = "dsp_b"; |
| 168 |
simple-audio-card,bitclock-master = <&sound0_master>; |
| 169 |
simple-audio-card,frame-master = <&sound0_master>; |
| 170 |
simple-audio-card,bitclock-inversion; |
| 171 |
|
| 172 |
sound0_master: simple-audio-card,cpu { |
| 173 |
sound-dai = <&mcasp3>; |
| 174 |
system-clock-frequency = <5644800>; |
| 175 |
}; |
| 176 |
|
| 177 |
simple-audio-card,codec { |
| 178 |
sound-dai = <&tlv320aic3106>; |
| 179 |
clocks = <&atl_clkin2_ck>; |
| 180 |
}; |
| 181 |
}; |
| 182 |
|
| 183 |
vmmcwl_fixed: fixedregulator-mmcwl { |
| 184 |
compatible = "regulator-fixed"; |
| 185 |
regulator-name = "vmmcwl_fixed"; |
| 186 |
regulator-min-microvolt = <1800000>; |
| 187 |
regulator-max-microvolt = <1800000>; |
| 188 |
gpio = <&gpio5 8 GPIO_ACTIVE_HIGH>; |
| 189 |
enable-active-high; |
| 190 |
}; |
| 191 |
|
| 192 |
clk_ov5640_fixed: clock { |
| 193 |
compatible = "fixed-clock"; |
| 194 |
#clock-cells = <0>; |
| 195 |
clock-frequency = <24000000>; |
| 196 |
}; |
| 197 |
}; |
| 198 |
|
| 199 |
&dra7_pmx_core { |
| 200 |
dcan1_pins_default: dcan1-default-pins { |
| 201 |
pinctrl-single,pins = < |
| 202 |
DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */ |
| 203 |
DRA7XX_CORE_IOPAD(0x3818, PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */ |
| 204 |
>; |
| 205 |
}; |
| 206 |
|
| 207 |
dcan1_pins_sleep: dcan1-sleep-pins { |
| 208 |
pinctrl-single,pins = < |
| 209 |
DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP) /* dcan1_tx.off */ |
| 210 |
DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP) /* wakeup0.off */ |
| 211 |
>; |
| 212 |
}; |
| 213 |
}; |
| 214 |
|
| 215 |
&i2c1 { |
| 216 |
status = "okay"; |
| 217 |
clock-frequency = <400000>; |
| 218 |
|
| 219 |
pcf_lcd: gpio@20 { |
| 220 |
compatible = "nxp,pcf8575"; |
| 221 |
reg = <0x20>; |
| 222 |
gpio-controller; |
| 223 |
#gpio-cells = <2>; |
| 224 |
interrupt-controller; |
| 225 |
#interrupt-cells = <2>; |
| 226 |
}; |
| 227 |
|
| 228 |
pcf_gpio_21: gpio@21 { |
| 229 |
compatible = "nxp,pcf8575"; |
| 230 |
reg = <0x21>; |
| 231 |
lines-initial-states = <0x1408>; |
| 232 |
gpio-controller; |
| 233 |
#gpio-cells = <2>; |
| 234 |
interrupt-controller; |
| 235 |
#interrupt-cells = <2>; |
| 236 |
}; |
| 237 |
|
| 238 |
tlv320aic3106: tlv320aic3106@19 { |
| 239 |
#sound-dai-cells = <0>; |
| 240 |
compatible = "ti,tlv320aic3106"; |
| 241 |
reg = <0x19>; |
| 242 |
adc-settle-ms = <40>; |
| 243 |
ai3x-micbias-vg = <1>; /* 2.0V */ |
| 244 |
status = "okay"; |
| 245 |
|
| 246 |
/* Regulators */ |
| 247 |
AVDD-supply = <&evm_3v3_sw>; |
| 248 |
IOVDD-supply = <&evm_3v3_sw>; |
| 249 |
DRVDD-supply = <&evm_3v3_sw>; |
| 250 |
DVDD-supply = <&aic_dvdd>; |
| 251 |
}; |
| 252 |
}; |
| 253 |
|
| 254 |
&i2c5 { |
| 255 |
status = "okay"; |
| 256 |
clock-frequency = <400000>; |
| 257 |
|
| 258 |
pcf_hdmi: pcf8575@26 { |
| 259 |
compatible = "nxp,pcf8575"; |
| 260 |
reg = <0x26>; |
| 261 |
gpio-controller; |
| 262 |
#gpio-cells = <2>; |
| 263 |
/* |
| 264 |
* initial state is used here to keep the mdio interface |
| 265 |
* selected on RU89 through SEL_VIN4_MUX_S0, VIN2_S1 and |
| 266 |
* VIN2_S0 driven high otherwise Ethernet stops working |
| 267 |
* VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6 |
| 268 |
*/ |
| 269 |
lines-initial-states = <0x0f2b>; |
| 270 |
|
| 271 |
hdmi-audio-hog { |
| 272 |
/* vin6_sel_s0: high: VIN6, low: audio */ |
| 273 |
gpio-hog; |
| 274 |
gpios = <1 GPIO_ACTIVE_HIGH>; |
| 275 |
output-low; |
| 276 |
line-name = "vin6_sel_s0"; |
| 277 |
}; |
| 278 |
}; |
| 279 |
|
| 280 |
ov5640@3c { |
| 281 |
compatible = "ovti,ov5640"; |
| 282 |
reg = <0x3c>; |
| 283 |
|
| 284 |
clocks = <&clk_ov5640_fixed>; |
| 285 |
clock-names = "xclk"; |
| 286 |
|
| 287 |
port { |
| 288 |
csi2_cam0: endpoint { |
| 289 |
remote-endpoint = <&csi2_phy0>; |
| 290 |
clock-lanes = <0>; |
| 291 |
data-lanes = <1 2>; |
| 292 |
}; |
| 293 |
}; |
| 294 |
}; |
| 295 |
|
| 296 |
}; |
| 297 |
|
| 298 |
&uart1 { |
| 299 |
status = "okay"; |
| 300 |
interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>, |
| 301 |
<&dra7_pmx_core 0x3e0>; |
| 302 |
}; |
| 303 |
|
| 304 |
&elm { |
| 305 |
status = "okay"; |
| 306 |
}; |
| 307 |
|
| 308 |
&gpmc { |
| 309 |
/* |
| 310 |
* For the existing IOdelay configuration via U-Boot we don't |
| 311 |
* support NAND on dra72-evm. Keep it disabled. Enabling it |
| 312 |
* requires a different configuration by U-Boot. |
| 313 |
*/ |
| 314 |
status = "disabled"; |
| 315 |
ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */ |
| 316 |
nand@0,0 { |
| 317 |
/* To use NAND, DIP switch SW5 must be set like so: |
| 318 |
* SW5.1 (NAND_SELn) = ON (LOW) |
| 319 |
* SW5.9 (GPMC_WPN) = OFF (HIGH) |
| 320 |
*/ |
| 321 |
compatible = "ti,omap2-nand"; |
| 322 |
reg = <0 0 4>; /* device IO registers */ |
| 323 |
interrupt-parent = <&gpmc>; |
| 324 |
interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ |
| 325 |
<1 IRQ_TYPE_NONE>; /* termcount */ |
| 326 |
rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */ |
| 327 |
ti,nand-xfer-type = "prefetch-dma"; |
| 328 |
ti,nand-ecc-opt = "bch8"; |
| 329 |
ti,elm-id = <&elm>; |
| 330 |
nand-bus-width = <16>; |
| 331 |
gpmc,device-width = <2>; |
| 332 |
gpmc,sync-clk-ps = <0>; |
| 333 |
gpmc,cs-on-ns = <0>; |
| 334 |
gpmc,cs-rd-off-ns = <80>; |
| 335 |
gpmc,cs-wr-off-ns = <80>; |
| 336 |
gpmc,adv-on-ns = <0>; |
| 337 |
gpmc,adv-rd-off-ns = <60>; |
| 338 |
gpmc,adv-wr-off-ns = <60>; |
| 339 |
gpmc,we-on-ns = <10>; |
| 340 |
gpmc,we-off-ns = <50>; |
| 341 |
gpmc,oe-on-ns = <4>; |
| 342 |
gpmc,oe-off-ns = <40>; |
| 343 |
gpmc,access-ns = <40>; |
| 344 |
gpmc,wr-access-ns = <80>; |
| 345 |
gpmc,rd-cycle-ns = <80>; |
| 346 |
gpmc,wr-cycle-ns = <80>; |
| 347 |
gpmc,bus-turnaround-ns = <0>; |
| 348 |
gpmc,cycle2cycle-delay-ns = <0>; |
| 349 |
gpmc,clk-activation-ns = <0>; |
| 350 |
gpmc,wr-data-mux-bus-ns = <0>; |
| 351 |
/* MTD partition table */ |
| 352 |
/* All SPL-* partitions are sized to minimal length |
| 353 |
* which can be independently programmable. For |
| 354 |
* NAND flash this is equal to size of erase-block */ |
| 355 |
#address-cells = <1>; |
| 356 |
#size-cells = <1>; |
| 357 |
partition@0 { |
| 358 |
label = "NAND.SPL"; |
| 359 |
reg = <0x00000000 0x00020000>; |
| 360 |
}; |
| 361 |
partition@1 { |
| 362 |
label = "NAND.SPL.backup1"; |
| 363 |
reg = <0x00020000 0x00020000>; |
| 364 |
}; |
| 365 |
partition@2 { |
| 366 |
label = "NAND.SPL.backup2"; |
| 367 |
reg = <0x00040000 0x00020000>; |
| 368 |
}; |
| 369 |
partition@3 { |
| 370 |
label = "NAND.SPL.backup3"; |
| 371 |
reg = <0x00060000 0x00020000>; |
| 372 |
}; |
| 373 |
partition@4 { |
| 374 |
label = "NAND.u-boot-spl-os"; |
| 375 |
reg = <0x00080000 0x00040000>; |
| 376 |
}; |
| 377 |
partition@5 { |
| 378 |
label = "NAND.u-boot"; |
| 379 |
reg = <0x000c0000 0x00100000>; |
| 380 |
}; |
| 381 |
partition@6 { |
| 382 |
label = "NAND.u-boot-env"; |
| 383 |
reg = <0x001c0000 0x00020000>; |
| 384 |
}; |
| 385 |
partition@7 { |
| 386 |
label = "NAND.u-boot-env.backup1"; |
| 387 |
reg = <0x001e0000 0x00020000>; |
| 388 |
}; |
| 389 |
partition@8 { |
| 390 |
label = "NAND.kernel"; |
| 391 |
reg = <0x00200000 0x00800000>; |
| 392 |
}; |
| 393 |
partition@9 { |
| 394 |
label = "NAND.file-system"; |
| 395 |
reg = <0x00a00000 0x0f600000>; |
| 396 |
}; |
| 397 |
}; |
| 398 |
}; |
| 399 |
|
| 400 |
&omap_dwc3_1 { |
| 401 |
extcon = <&extcon_usb1>; |
| 402 |
}; |
| 403 |
|
| 404 |
&omap_dwc3_2 { |
| 405 |
extcon = <&extcon_usb2>; |
| 406 |
}; |
| 407 |
|
| 408 |
&usb1 { |
| 409 |
dr_mode = "otg"; |
| 410 |
extcon = <&extcon_usb1>; |
| 411 |
}; |
| 412 |
|
| 413 |
&usb2 { |
| 414 |
dr_mode = "host"; |
| 415 |
extcon = <&extcon_usb2>; |
| 416 |
}; |
| 417 |
|
| 418 |
&mmc1 { |
| 419 |
status = "okay"; |
| 420 |
pinctrl-names = "default"; |
| 421 |
pinctrl-0 = <&mmc1_pins_default>; |
| 422 |
vmmc-supply = <&evm_3v3_sd>; |
| 423 |
bus-width = <4>; |
| 424 |
/* |
| 425 |
* SDCD signal is not being used here - using the fact that GPIO mode |
| 426 |
* is a viable alternative |
| 427 |
*/ |
| 428 |
cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; |
| 429 |
max-frequency = <192000000>; |
| 430 |
}; |
| 431 |
|
| 432 |
&mmc2 { |
| 433 |
/* SW5-3 in ON position */ |
| 434 |
status = "okay"; |
| 435 |
pinctrl-names = "default"; |
| 436 |
pinctrl-0 = <&mmc2_pins_default>; |
| 437 |
bus-width = <8>; |
| 438 |
non-removable; |
| 439 |
max-frequency = <192000000>; |
| 440 |
}; |
| 441 |
|
| 442 |
&mmc4 { |
| 443 |
status = "okay"; |
| 444 |
vmmc-supply = <&evm_3v6>; |
| 445 |
vqmmc-supply = <&vmmcwl_fixed>; |
| 446 |
bus-width = <4>; |
| 447 |
cap-power-off-card; |
| 448 |
keep-power-in-suspend; |
| 449 |
non-removable; |
| 450 |
pinctrl-names = "default", "hs", "sdr12", "sdr25"; |
| 451 |
pinctrl-0 = <&mmc4_pins_default>; |
| 452 |
pinctrl-1 = <&mmc4_pins_default>; |
| 453 |
pinctrl-2 = <&mmc4_pins_default>; |
| 454 |
pinctrl-3 = <&mmc4_pins_default>; |
| 455 |
#address-cells = <1>; |
| 456 |
#size-cells = <0>; |
| 457 |
wifi@2 { |
| 458 |
compatible = "ti,wl1835"; |
| 459 |
reg = <2>; |
| 460 |
interrupt-parent = <&gpio5>; |
| 461 |
interrupts = <7 IRQ_TYPE_EDGE_RISING>; |
| 462 |
}; |
| 463 |
}; |
| 464 |
|
| 465 |
&dcan1 { |
| 466 |
status = "okay"; |
| 467 |
pinctrl-names = "default", "sleep", "active"; |
| 468 |
pinctrl-0 = <&dcan1_pins_sleep>; |
| 469 |
pinctrl-1 = <&dcan1_pins_sleep>; |
| 470 |
pinctrl-2 = <&dcan1_pins_default>; |
| 471 |
}; |
| 472 |
|
| 473 |
&qspi { |
| 474 |
status = "okay"; |
| 475 |
|
| 476 |
spi-max-frequency = <76800000>; |
| 477 |
flash@0 { |
| 478 |
compatible = "s25fl256s1"; |
| 479 |
spi-max-frequency = <76800000>; |
| 480 |
reg = <0>; |
| 481 |
spi-tx-bus-width = <1>; |
| 482 |
spi-rx-bus-width = <4>; |
| 483 |
#address-cells = <1>; |
| 484 |
#size-cells = <1>; |
| 485 |
|
| 486 |
/* MTD partition table. |
| 487 |
* The ROM checks the first four physical blocks |
| 488 |
* for a valid file to boot and the flash here is |
| 489 |
* 64KiB block size. |
| 490 |
*/ |
| 491 |
partition@0 { |
| 492 |
label = "QSPI.SPL"; |
| 493 |
reg = <0x00000000 0x00010000>; |
| 494 |
}; |
| 495 |
partition@1 { |
| 496 |
label = "QSPI.SPL.backup1"; |
| 497 |
reg = <0x00010000 0x00010000>; |
| 498 |
}; |
| 499 |
partition@2 { |
| 500 |
label = "QSPI.SPL.backup2"; |
| 501 |
reg = <0x00020000 0x00010000>; |
| 502 |
}; |
| 503 |
partition@3 { |
| 504 |
label = "QSPI.SPL.backup3"; |
| 505 |
reg = <0x00030000 0x00010000>; |
| 506 |
}; |
| 507 |
partition@4 { |
| 508 |
label = "QSPI.u-boot"; |
| 509 |
reg = <0x00040000 0x00100000>; |
| 510 |
}; |
| 511 |
partition@5 { |
| 512 |
label = "QSPI.u-boot-spl-os"; |
| 513 |
reg = <0x00140000 0x00080000>; |
| 514 |
}; |
| 515 |
partition@6 { |
| 516 |
label = "QSPI.u-boot-env"; |
| 517 |
reg = <0x001c0000 0x00010000>; |
| 518 |
}; |
| 519 |
partition@7 { |
| 520 |
label = "QSPI.u-boot-env.backup1"; |
| 521 |
reg = <0x001d0000 0x0010000>; |
| 522 |
}; |
| 523 |
partition@8 { |
| 524 |
label = "QSPI.kernel"; |
| 525 |
reg = <0x001e0000 0x0800000>; |
| 526 |
}; |
| 527 |
partition@9 { |
| 528 |
label = "QSPI.file-system"; |
| 529 |
reg = <0x009e0000 0x01620000>; |
| 530 |
}; |
| 531 |
}; |
| 532 |
}; |
| 533 |
|
| 534 |
&dss { |
| 535 |
status = "okay"; |
| 536 |
}; |
| 537 |
|
| 538 |
&hdmi { |
| 539 |
status = "okay"; |
| 540 |
|
| 541 |
port { |
| 542 |
hdmi_out: endpoint { |
| 543 |
remote-endpoint = <&tpd12s015_in>; |
| 544 |
}; |
| 545 |
}; |
| 546 |
}; |
| 547 |
|
| 548 |
&atl { |
| 549 |
assigned-clocks = <&abe_dpll_sys_clk_mux>, |
| 550 |
<&atl_clkctrl DRA7_ATL_ATL_CLKCTRL 26>, |
| 551 |
<&dpll_abe_ck>, |
| 552 |
<&dpll_abe_m2x2_ck>, |
| 553 |
<&atl_clkin2_ck>; |
| 554 |
assigned-clock-parents = <&sys_clkin2>, <&dpll_abe_m2_ck>; |
| 555 |
assigned-clock-rates = <0>, <0>, <180633600>, <361267200>, <5644800>; |
| 556 |
|
| 557 |
status = "okay"; |
| 558 |
|
| 559 |
atl2 { |
| 560 |
bws = <DRA7_ATL_WS_MCASP2_FSX>; |
| 561 |
aws = <DRA7_ATL_WS_MCASP3_FSX>; |
| 562 |
}; |
| 563 |
}; |
| 564 |
|
| 565 |
&mcasp3 { |
| 566 |
#sound-dai-cells = <0>; |
| 567 |
|
| 568 |
assigned-clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>; |
| 569 |
assigned-clock-parents = <&atl_clkin2_ck>; |
| 570 |
|
| 571 |
status = "okay"; |
| 572 |
|
| 573 |
op-mode = <0>; /* MCASP_IIS_MODE */ |
| 574 |
tdm-slots = <2>; |
| 575 |
/* 4 serializer */ |
| 576 |
serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ |
| 577 |
1 2 0 0 |
| 578 |
>; |
| 579 |
tx-num-evt = <32>; |
| 580 |
rx-num-evt = <32>; |
| 581 |
}; |
| 582 |
|
| 583 |
&pcie1_rc { |
| 584 |
status = "okay"; |
| 585 |
}; |
| 586 |
|
| 587 |
&csi2_0 { |
| 588 |
csi2_phy0: endpoint { |
| 589 |
remote-endpoint = <&csi2_cam0>; |
| 590 |
clock-lanes = <0>; |
| 591 |
data-lanes = <1 2>; |
| 592 |
}; |
| 593 |
}; |