| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
|
| 3 |
#include <dt-bindings/input/input.h> |
| 4 |
|
| 5 |
/ { |
| 6 |
cpus { |
| 7 |
cpu@0 { |
| 8 |
cpu0-supply = <&vcc>; |
| 9 |
}; |
| 10 |
}; |
| 11 |
|
| 12 |
memory@80000000 { |
| 13 |
device_type = "memory"; |
| 14 |
reg = <0x80000000 0>; |
| 15 |
}; |
| 16 |
|
| 17 |
wl12xx_vmmc: wl12xx_vmmc { |
| 18 |
compatible = "regulator-fixed"; |
| 19 |
regulator-name = "vwl1271"; |
| 20 |
regulator-min-microvolt = <1800000>; |
| 21 |
regulator-max-microvolt = <1800000>; |
| 22 |
gpio = <&gpio1 3 0>; /* gpio_3 */ |
| 23 |
startup-delay-us = <70000>; |
| 24 |
enable-active-high; |
| 25 |
vin-supply = <&vaux3>; |
| 26 |
}; |
| 27 |
|
| 28 |
/* HS USB Host PHY on PORT 1 */ |
| 29 |
hsusb2_phy: hsusb2_phy { |
| 30 |
pinctrl-names = "default"; |
| 31 |
pinctrl-0 = <&hsusb2_reset_pin>; |
| 32 |
compatible = "usb-nop-xceiv"; |
| 33 |
reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */ |
| 34 |
#phy-cells = <0>; |
| 35 |
}; |
| 36 |
|
| 37 |
/* fixed 26MHz oscillator */ |
| 38 |
hfclk_26m: oscillator { |
| 39 |
#clock-cells = <0>; |
| 40 |
compatible = "fixed-clock"; |
| 41 |
clock-frequency = <26000000>; |
| 42 |
}; |
| 43 |
}; |
| 44 |
|
| 45 |
&gpmc { |
| 46 |
ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */ |
| 47 |
|
| 48 |
nand@0,0 { |
| 49 |
compatible = "ti,omap2-nand"; |
| 50 |
reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ |
| 51 |
interrupt-parent = <&gpmc>; |
| 52 |
interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ |
| 53 |
<1 IRQ_TYPE_NONE>; /* termcount */ |
| 54 |
nand-bus-width = <16>; |
| 55 |
ti,nand-ecc-opt = "bch8"; |
| 56 |
rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */ |
| 57 |
gpmc,sync-clk-ps = <0>; |
| 58 |
gpmc,cs-on-ns = <0>; |
| 59 |
gpmc,cs-rd-off-ns = <44>; |
| 60 |
gpmc,cs-wr-off-ns = <44>; |
| 61 |
gpmc,adv-on-ns = <6>; |
| 62 |
gpmc,adv-rd-off-ns = <34>; |
| 63 |
gpmc,adv-wr-off-ns = <44>; |
| 64 |
gpmc,we-off-ns = <40>; |
| 65 |
gpmc,oe-off-ns = <54>; |
| 66 |
gpmc,access-ns = <64>; |
| 67 |
gpmc,rd-cycle-ns = <82>; |
| 68 |
gpmc,wr-cycle-ns = <82>; |
| 69 |
gpmc,wr-access-ns = <40>; |
| 70 |
gpmc,wr-data-mux-bus-ns = <0>; |
| 71 |
gpmc,device-width = <2>; |
| 72 |
#address-cells = <1>; |
| 73 |
#size-cells = <1>; |
| 74 |
}; |
| 75 |
}; |
| 76 |
|
| 77 |
&i2c1 { |
| 78 |
pinctrl-names = "default"; |
| 79 |
pinctrl-0 = <&i2c1_pins>; |
| 80 |
clock-frequency = <2600000>; |
| 81 |
|
| 82 |
twl: twl@48 { |
| 83 |
reg = <0x48>; |
| 84 |
interrupts = <7>; /* SYS_NIRQ cascaded to intc */ |
| 85 |
interrupt-parent = <&intc>; |
| 86 |
clocks = <&hfclk_26m>; |
| 87 |
clock-names = "fck"; |
| 88 |
twl_audio: audio { |
| 89 |
compatible = "ti,twl4030-audio"; |
| 90 |
codec { |
| 91 |
ti,hs_extmute_gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>; |
| 92 |
}; |
| 93 |
}; |
| 94 |
}; |
| 95 |
}; |
| 96 |
|
| 97 |
&i2c2 { |
| 98 |
pinctrl-names = "default"; |
| 99 |
pinctrl-0 = <&i2c2_pins>; |
| 100 |
clock-frequency = <400000>; |
| 101 |
}; |
| 102 |
|
| 103 |
&i2c3 { |
| 104 |
pinctrl-names = "default"; |
| 105 |
pinctrl-0 = <&i2c3_pins>; |
| 106 |
clock-frequency = <400000>; |
| 107 |
|
| 108 |
touchscreen: tsc2004@48 { |
| 109 |
compatible = "ti,tsc2004"; |
| 110 |
reg = <0x48>; |
| 111 |
vio-supply = <&vaux1>; |
| 112 |
pinctrl-names = "default"; |
| 113 |
pinctrl-0 = <&tsc2004_pins>; |
| 114 |
interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */ |
| 115 |
|
| 116 |
touchscreen-fuzz-x = <4>; |
| 117 |
touchscreen-fuzz-y = <7>; |
| 118 |
touchscreen-fuzz-pressure = <2>; |
| 119 |
touchscreen-size-x = <4096>; |
| 120 |
touchscreen-size-y = <4096>; |
| 121 |
touchscreen-max-pressure = <2048>; |
| 122 |
|
| 123 |
ti,x-plate-ohms = <280>; |
| 124 |
ti,esd-recovery-timeout-ms = <8000>; |
| 125 |
}; |
| 126 |
}; |
| 127 |
|
| 128 |
&mmc3 { |
| 129 |
interrupts-extended = <&intc 94 &omap3_pmx_core 0x136>; |
| 130 |
pinctrl-0 = <&mmc3_pins &wl127x_gpio>; |
| 131 |
pinctrl-names = "default"; |
| 132 |
vmmc-supply = <&wl12xx_vmmc>; |
| 133 |
non-removable; |
| 134 |
bus-width = <4>; |
| 135 |
cap-power-off-card; |
| 136 |
#address-cells = <1>; |
| 137 |
#size-cells = <0>; |
| 138 |
wlcore: wlcore@2 { |
| 139 |
compatible = "ti,wl1273"; |
| 140 |
reg = <2>; |
| 141 |
interrupt-parent = <&gpio1>; |
| 142 |
interrupts = <2 IRQ_TYPE_EDGE_RISING>; /* gpio 2 */ |
| 143 |
ref-clock-frequency = <26000000>; |
| 144 |
}; |
| 145 |
}; |
| 146 |
|
| 147 |
&usbhshost { |
| 148 |
pinctrl-names = "default"; |
| 149 |
pinctrl-0 = <&hsusb2_pins>; |
| 150 |
port2-mode = "ehci-phy"; |
| 151 |
}; |
| 152 |
|
| 153 |
&usbhsehci { |
| 154 |
phys = <0 &hsusb2_phy>; |
| 155 |
}; |
| 156 |
|
| 157 |
&omap3_pmx_core { |
| 158 |
|
| 159 |
mmc3_pins: mm3-pins { |
| 160 |
pinctrl-single,pins = < |
| 161 |
OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */ |
| 162 |
OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */ |
| 163 |
OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */ |
| 164 |
OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */ |
| 165 |
OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */ |
| 166 |
OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */ |
| 167 |
>; |
| 168 |
}; |
| 169 |
mcbsp2_pins: mcbsp2-pins { |
| 170 |
pinctrl-single,pins = < |
| 171 |
OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */ |
| 172 |
OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */ |
| 173 |
OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */ |
| 174 |
OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */ |
| 175 |
>; |
| 176 |
}; |
| 177 |
uart2_pins: uart2-pins { |
| 178 |
pinctrl-single,pins = < |
| 179 |
OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */ |
| 180 |
OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/ |
| 181 |
OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ |
| 182 |
OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */ |
| 183 |
OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */ |
| 184 |
>; |
| 185 |
}; |
| 186 |
mcspi1_pins: mcspi1-pins { |
| 187 |
pinctrl-single,pins = < |
| 188 |
OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ |
| 189 |
OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */ |
| 190 |
OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */ |
| 191 |
OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */ |
| 192 |
>; |
| 193 |
}; |
| 194 |
|
| 195 |
hsusb2_pins: hsusb2-pins { |
| 196 |
pinctrl-single,pins = < |
| 197 |
OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ |
| 198 |
OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */ |
| 199 |
OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */ |
| 200 |
OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */ |
| 201 |
OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */ |
| 202 |
OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */ |
| 203 |
>; |
| 204 |
}; |
| 205 |
|
| 206 |
hsusb_otg_pins: hsusb-otg-pins { |
| 207 |
pinctrl-single,pins = < |
| 208 |
OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */ |
| 209 |
OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */ |
| 210 |
OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */ |
| 211 |
OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */ |
| 212 |
OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */ |
| 213 |
OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */ |
| 214 |
OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */ |
| 215 |
OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */ |
| 216 |
OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */ |
| 217 |
OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */ |
| 218 |
OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */ |
| 219 |
OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */ |
| 220 |
>; |
| 221 |
}; |
| 222 |
|
| 223 |
i2c1_pins: i2c1-pins { |
| 224 |
pinctrl-single,pins = < |
| 225 |
OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ |
| 226 |
OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ |
| 227 |
OMAP3_CORE1_IOPAD(0x20ba, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs6.gpio_57 */ |
| 228 |
>; |
| 229 |
}; |
| 230 |
|
| 231 |
i2c2_pins: i2c2-pins { |
| 232 |
pinctrl-single,pins = < |
| 233 |
OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl */ |
| 234 |
OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda */ |
| 235 |
>; |
| 236 |
}; |
| 237 |
|
| 238 |
i2c3_pins: i2c3-pins { |
| 239 |
pinctrl-single,pins = < |
| 240 |
OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl */ |
| 241 |
OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda */ |
| 242 |
>; |
| 243 |
}; |
| 244 |
|
| 245 |
tsc2004_pins: tsc2004-pins { |
| 246 |
pinctrl-single,pins = < |
| 247 |
OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4) /* mcbsp4_dr.gpio_153 */ |
| 248 |
>; |
| 249 |
}; |
| 250 |
}; |
| 251 |
|
| 252 |
&omap3_pmx_wkup { |
| 253 |
|
| 254 |
hsusb2_reset_pin: hsusb1-reset-pins { |
| 255 |
pinctrl-single,pins = < |
| 256 |
OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */ |
| 257 |
>; |
| 258 |
}; |
| 259 |
wl127x_gpio: wl127x-gpio-pins { |
| 260 |
pinctrl-single,pins = < |
| 261 |
OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT | MUX_MODE4) /* sys_boot0.gpio_2 */ |
| 262 |
OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */ |
| 263 |
>; |
| 264 |
}; |
| 265 |
}; |
| 266 |
|
| 267 |
&uart2 { |
| 268 |
interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>; |
| 269 |
pinctrl-names = "default"; |
| 270 |
pinctrl-0 = <&uart2_pins>; |
| 271 |
}; |
| 272 |
|
| 273 |
&mcspi1 { |
| 274 |
pinctrl-names = "default"; |
| 275 |
pinctrl-0 = <&mcspi1_pins>; |
| 276 |
}; |
| 277 |
|
| 278 |
#include "twl4030.dtsi" |
| 279 |
#include "twl4030_omap3.dtsi" |
| 280 |
|
| 281 |
&vaux3 { |
| 282 |
regulator-min-microvolt = <2800000>; |
| 283 |
regulator-max-microvolt = <2800000>; |
| 284 |
}; |
| 285 |
|
| 286 |
&twl { |
| 287 |
twl_power: power { |
| 288 |
compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle"; |
| 289 |
ti,use_poweroff; |
| 290 |
}; |
| 291 |
}; |
| 292 |
|
| 293 |
&twl_gpio { |
| 294 |
ti,use-leds; |
| 295 |
}; |