| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/dts-v1/; |
| 3 |
|
| 4 |
#include <dt-bindings/input/input.h> |
| 5 |
#include "omap443x.dtsi" |
| 6 |
#include "motorola-cpcap-mapphone.dtsi" |
| 7 |
|
| 8 |
/ { |
| 9 |
/* |
| 10 |
* We seem to have only 1021 MB accessible, 1021 - 1022 is locked, |
| 11 |
* then 1023 - 1024 seems to contain mbm. |
| 12 |
*/ |
| 13 |
memory { |
| 14 |
device_type = "memory"; |
| 15 |
reg = <0x80000000 0x3fd00000>; /* 1021 MB */ |
| 16 |
}; |
| 17 |
|
| 18 |
/* Poweroff GPIO probably connected to CPCAP */ |
| 19 |
gpio-poweroff { |
| 20 |
compatible = "gpio-poweroff"; |
| 21 |
pinctrl-0 = <&poweroff_gpio>; |
| 22 |
pinctrl-names = "default"; |
| 23 |
gpios = <&gpio2 18 GPIO_ACTIVE_LOW>; /* gpio50 */ |
| 24 |
}; |
| 25 |
|
| 26 |
hdmi0: connector { |
| 27 |
compatible = "hdmi-connector"; |
| 28 |
pinctrl-0 = <&hdmi_hpd_gpio>; |
| 29 |
pinctrl-names = "default"; |
| 30 |
label = "hdmi"; |
| 31 |
type = "d"; |
| 32 |
|
| 33 |
hpd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; /* gpio63 */ |
| 34 |
|
| 35 |
port { |
| 36 |
hdmi_connector_in: endpoint { |
| 37 |
remote-endpoint = <&hdmi_out>; |
| 38 |
}; |
| 39 |
}; |
| 40 |
}; |
| 41 |
|
| 42 |
/* |
| 43 |
* HDMI 5V regulator probably sourced from battery. Let's keep |
| 44 |
* keep this as always enabled for HDMI to work until we've |
| 45 |
* figured what the encoder chip is. |
| 46 |
*/ |
| 47 |
hdmi_regulator: regulator-hdmi { |
| 48 |
compatible = "regulator-fixed"; |
| 49 |
regulator-name = "hdmi"; |
| 50 |
regulator-min-microvolt = <5000000>; |
| 51 |
regulator-max-microvolt = <5000000>; |
| 52 |
gpio = <&gpio2 27 GPIO_ACTIVE_HIGH>; /* gpio59 */ |
| 53 |
enable-active-high; |
| 54 |
regulator-always-on; |
| 55 |
}; |
| 56 |
|
| 57 |
/* This is probably coming straight from the battery.. */ |
| 58 |
wl12xx_vmmc: regulator-wl12xx { |
| 59 |
compatible = "regulator-fixed"; |
| 60 |
regulator-name = "vwl1271"; |
| 61 |
regulator-min-microvolt = <1650000>; |
| 62 |
regulator-max-microvolt = <1650000>; |
| 63 |
gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; /* gpio94 */ |
| 64 |
startup-delay-us = <70000>; |
| 65 |
enable-active-high; |
| 66 |
}; |
| 67 |
|
| 68 |
soundcard { |
| 69 |
compatible = "audio-graph-card"; |
| 70 |
label = "Mapphone Audio"; |
| 71 |
|
| 72 |
widgets = |
| 73 |
"Speaker", "Earpiece", |
| 74 |
"Speaker", "Loudspeaker", |
| 75 |
"Headphone", "Headphone Jack", |
| 76 |
"Microphone", "Internal Mic"; |
| 77 |
|
| 78 |
routing = |
| 79 |
"Earpiece", "EP", |
| 80 |
"Loudspeaker", "SPKR", |
| 81 |
"Headphone Jack", "HSL", |
| 82 |
"Headphone Jack", "HSR", |
| 83 |
"MICR", "Internal Mic"; |
| 84 |
|
| 85 |
dais = <&mcbsp2_port>, <&mcbsp3_port>; |
| 86 |
}; |
| 87 |
}; |
| 88 |
|
| 89 |
&cpu_thermal { |
| 90 |
polling-delay = <10000>; /* milliseconds */ |
| 91 |
}; |
| 92 |
|
| 93 |
&cpu_alert0 { |
| 94 |
temperature = <80000>; /* millicelsius */ |
| 95 |
}; |
| 96 |
|
| 97 |
&cpu0 { |
| 98 |
/* |
| 99 |
* Note that the 1.2GiHz mode is enabled for all SoC variants for |
| 100 |
* the Motorola Android Linux v3.0.8 based kernel. |
| 101 |
*/ |
| 102 |
operating-points = < |
| 103 |
/* kHz uV */ |
| 104 |
300000 1025000 |
| 105 |
600000 1200000 |
| 106 |
800000 1313000 |
| 107 |
1008000 1375000 |
| 108 |
1200000 1375000 |
| 109 |
>; |
| 110 |
}; |
| 111 |
|
| 112 |
&dss { |
| 113 |
status = "okay"; |
| 114 |
}; |
| 115 |
|
| 116 |
&hdmi { |
| 117 |
status = "okay"; |
| 118 |
pinctrl-0 = <&dss_hdmi_pins>; |
| 119 |
pinctrl-names = "default"; |
| 120 |
vdda-supply = <&vdac>; |
| 121 |
|
| 122 |
port { |
| 123 |
hdmi_out: endpoint { |
| 124 |
remote-endpoint = <&hdmi_connector_in>; |
| 125 |
lanes = <1 0 3 2 5 4 7 6>; |
| 126 |
}; |
| 127 |
}; |
| 128 |
}; |
| 129 |
|
| 130 |
&i2c1 { |
| 131 |
tmp105@48 { |
| 132 |
compatible = "ti,tmp105"; |
| 133 |
reg = <0x48>; |
| 134 |
pinctrl-0 = <&tmp105_irq>; |
| 135 |
pinctrl-names = "default"; |
| 136 |
/* kpd_row0.gpio_178 */ |
| 137 |
interrupts-extended = <&gpio6 18 IRQ_TYPE_EDGE_FALLING |
| 138 |
&omap4_pmx_core 0x14e>; |
| 139 |
interrupt-names = "irq", "wakeup"; |
| 140 |
wakeup-source; |
| 141 |
}; |
| 142 |
}; |
| 143 |
|
| 144 |
&mmc1 { |
| 145 |
vmmc-supply = <&vwlan2>; |
| 146 |
bus-width = <4>; |
| 147 |
cd-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; /* gpio176 */ |
| 148 |
}; |
| 149 |
|
| 150 |
&mmc2 { |
| 151 |
vmmc-supply = <&vsdio>; |
| 152 |
bus-width = <8>; |
| 153 |
ti,non-removable; |
| 154 |
}; |
| 155 |
|
| 156 |
&mmc3 { |
| 157 |
pinctrl-names = "default"; |
| 158 |
pinctrl-0 = <&mmc3_pins>; |
| 159 |
vmmc-supply = <&wl12xx_vmmc>; |
| 160 |
/* uart2_tx.sdmmc3_dat1 pad as wakeirq */ |
| 161 |
interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH |
| 162 |
&omap4_pmx_core 0xde>; |
| 163 |
interrupt-names = "irq", "wakeup"; |
| 164 |
non-removable; |
| 165 |
bus-width = <4>; |
| 166 |
cap-power-off-card; |
| 167 |
keep-power-in-suspend; |
| 168 |
|
| 169 |
#address-cells = <1>; |
| 170 |
#size-cells = <0>; |
| 171 |
wlcore: wlcore@2 { |
| 172 |
compatible = "ti,wl1285"; |
| 173 |
reg = <2>; |
| 174 |
/* gpio_100 with gpmc_wait2 pad as wakeirq */ |
| 175 |
interrupts-extended = <&gpio4 4 IRQ_TYPE_LEVEL_HIGH>, |
| 176 |
<&omap4_pmx_core 0x4e>; |
| 177 |
interrupt-names = "irq", "wakeup"; |
| 178 |
ref-clock-frequency = <26000000>; |
| 179 |
tcxo-clock-frequency = <26000000>; |
| 180 |
}; |
| 181 |
}; |
| 182 |
|
| 183 |
&omap4_pmx_core { |
| 184 |
|
| 185 |
/* hdmi_hpd.gpio_63 */ |
| 186 |
hdmi_hpd_gpio: hdmi-hpd-pins { |
| 187 |
pinctrl-single,pins = < |
| 188 |
OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3) |
| 189 |
>; |
| 190 |
}; |
| 191 |
|
| 192 |
/* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */ |
| 193 |
dss_hdmi_pins: dss-hdmi-pins { |
| 194 |
pinctrl-single,pins = < |
| 195 |
OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) |
| 196 |
OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0) |
| 197 |
OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0) |
| 198 |
>; |
| 199 |
}; |
| 200 |
|
| 201 |
/* |
| 202 |
* Android uses PIN_OFF_INPUT_PULLDOWN | PIN_INPUT_PULLUP | MUX_MODE3 |
| 203 |
* for gpio_100, but the internal pull makes wlan flakey on some |
| 204 |
* devices. Off mode value should be tested if we have off mode working |
| 205 |
* later on. |
| 206 |
*/ |
| 207 |
mmc3_pins: mmc3-pins { |
| 208 |
pinctrl-single,pins = < |
| 209 |
/* 0x4a10008e gpmc_wait2.gpio_100 d23 */ |
| 210 |
OMAP4_IOPAD(0x08e, PIN_INPUT | MUX_MODE3) |
| 211 |
|
| 212 |
/* 0x4a100102 abe_mcbsp1_dx.sdmmc3_dat2 ab25 */ |
| 213 |
OMAP4_IOPAD(0x102, PIN_INPUT_PULLUP | MUX_MODE1) |
| 214 |
|
| 215 |
/* 0x4a100104 abe_mcbsp1_fsx.sdmmc3_dat3 ac27 */ |
| 216 |
OMAP4_IOPAD(0x104, PIN_INPUT_PULLUP | MUX_MODE1) |
| 217 |
|
| 218 |
/* 0x4a100118 uart2_cts.sdmmc3_clk ab26 */ |
| 219 |
OMAP4_IOPAD(0x118, PIN_INPUT | MUX_MODE1) |
| 220 |
|
| 221 |
/* 0x4a10011a uart2_rts.sdmmc3_cmd ab27 */ |
| 222 |
OMAP4_IOPAD(0x11a, PIN_INPUT_PULLUP | MUX_MODE1) |
| 223 |
|
| 224 |
/* 0x4a10011c uart2_rx.sdmmc3_dat0 aa25 */ |
| 225 |
OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE1) |
| 226 |
|
| 227 |
/* 0x4a10011e uart2_tx.sdmmc3_dat1 aa26 */ |
| 228 |
OMAP4_IOPAD(0x11e, PIN_INPUT_PULLUP | MUX_MODE1) |
| 229 |
>; |
| 230 |
}; |
| 231 |
|
| 232 |
/* gpmc_ncs0.gpio_50 */ |
| 233 |
poweroff_gpio: poweroff-pins { |
| 234 |
pinctrl-single,pins = < |
| 235 |
OMAP4_IOPAD(0x074, PIN_OUTPUT_PULLUP | MUX_MODE3) |
| 236 |
>; |
| 237 |
}; |
| 238 |
|
| 239 |
/* kpd_row0.gpio_178 */ |
| 240 |
tmp105_irq: tmp105-irq-pins { |
| 241 |
pinctrl-single,pins = < |
| 242 |
OMAP4_IOPAD(0x18e, PIN_INPUT_PULLUP | MUX_MODE3) |
| 243 |
>; |
| 244 |
}; |
| 245 |
|
| 246 |
usb_gpio_mux_sel1: usb-gpio-mux-sel1-pins { |
| 247 |
/* gpio_60 */ |
| 248 |
pinctrl-single,pins = < |
| 249 |
OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3) |
| 250 |
>; |
| 251 |
}; |
| 252 |
|
| 253 |
usb_ulpi_pins: usb-ulpi-pins { |
| 254 |
pinctrl-single,pins = < |
| 255 |
OMAP4_IOPAD(0x196, MUX_MODE7) |
| 256 |
OMAP4_IOPAD(0x198, MUX_MODE7) |
| 257 |
OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE0) |
| 258 |
OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0) |
| 259 |
OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE0) |
| 260 |
OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE0) |
| 261 |
OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE0) |
| 262 |
OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE0) |
| 263 |
OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE0) |
| 264 |
OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE0) |
| 265 |
OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE0) |
| 266 |
OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE0) |
| 267 |
OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE0) |
| 268 |
OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE0) |
| 269 |
>; |
| 270 |
}; |
| 271 |
|
| 272 |
/* usb0_otg_dp and usb0_otg_dm */ |
| 273 |
usb_utmi_pins: usb-utmi-pins { |
| 274 |
pinctrl-single,pins = < |
| 275 |
OMAP4_IOPAD(0x196, PIN_INPUT | MUX_MODE0) |
| 276 |
OMAP4_IOPAD(0x198, PIN_INPUT | MUX_MODE0) |
| 277 |
OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7) |
| 278 |
OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7) |
| 279 |
OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7) |
| 280 |
OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7) |
| 281 |
OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE7) |
| 282 |
OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE7) |
| 283 |
OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7) |
| 284 |
OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7) |
| 285 |
OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7) |
| 286 |
OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7) |
| 287 |
OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7) |
| 288 |
OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7) |
| 289 |
>; |
| 290 |
}; |
| 291 |
|
| 292 |
/* |
| 293 |
* Note that the v3.0.8 stock userspace dynamically remuxes uart1 |
| 294 |
* rts pin probably for PM purposes to PIN_INPUT_PULLUP | MUX_MODE7 |
| 295 |
* when not used. If needed, we can add rts pin remux later based |
| 296 |
* on power measurements. |
| 297 |
*/ |
| 298 |
uart1_pins: uart1-pins { |
| 299 |
pinctrl-single,pins = < |
| 300 |
/* 0x4a10013c mcspi1_cs2.uart1_cts ag23 */ |
| 301 |
OMAP4_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE1) |
| 302 |
|
| 303 |
/* 0x4a10013e mcspi1_cs3.uart1_rts ah23 */ |
| 304 |
OMAP4_IOPAD(0x13e, MUX_MODE1) |
| 305 |
|
| 306 |
/* 0x4a100140 uart3_cts_rctx.uart1_tx f27 */ |
| 307 |
OMAP4_IOPAD(0x140, PIN_OUTPUT | MUX_MODE1) |
| 308 |
|
| 309 |
/* 0x4a1001ca dpm_emu14.uart1_rx aa3 */ |
| 310 |
OMAP4_IOPAD(0x1ca, PIN_INPUT_PULLUP | MUX_MODE2) |
| 311 |
>; |
| 312 |
}; |
| 313 |
|
| 314 |
/* uart3_tx_irtx and uart3_rx_irrx */ |
| 315 |
uart3_pins: uart3-pins { |
| 316 |
pinctrl-single,pins = < |
| 317 |
OMAP4_IOPAD(0x196, MUX_MODE7) |
| 318 |
OMAP4_IOPAD(0x198, MUX_MODE7) |
| 319 |
OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7) |
| 320 |
OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7) |
| 321 |
OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7) |
| 322 |
OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7) |
| 323 |
OMAP4_IOPAD(0x1ba, MUX_MODE2) |
| 324 |
OMAP4_IOPAD(0x1bc, PIN_INPUT | MUX_MODE2) |
| 325 |
OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7) |
| 326 |
OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7) |
| 327 |
OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7) |
| 328 |
OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7) |
| 329 |
OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7) |
| 330 |
OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7) |
| 331 |
>; |
| 332 |
}; |
| 333 |
|
| 334 |
uart4_pins: uart4-pins { |
| 335 |
pinctrl-single,pins = < |
| 336 |
OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0) /* uart4_rx */ |
| 337 |
OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0) /* uart4_tx */ |
| 338 |
OMAP4_IOPAD(0x110, PIN_INPUT_PULLUP | MUX_MODE5) /* uart4_cts */ |
| 339 |
OMAP4_IOPAD(0x112, PIN_OUTPUT_PULLUP | MUX_MODE5) /* uart4_rts */ |
| 340 |
>; |
| 341 |
}; |
| 342 |
|
| 343 |
mcbsp2_pins: mcbsp2-pins { |
| 344 |
pinctrl-single,pins = < |
| 345 |
OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_clkx */ |
| 346 |
OMAP4_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_dr */ |
| 347 |
OMAP4_IOPAD(0x0fa, PIN_OUTPUT | MUX_MODE0) /* abe_mcbsp2_dx */ |
| 348 |
OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_fsx */ |
| 349 |
>; |
| 350 |
}; |
| 351 |
|
| 352 |
mcbsp3_pins: mcbsp3-pins { |
| 353 |
pinctrl-single,pins = < |
| 354 |
OMAP4_IOPAD(0x106, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_dr */ |
| 355 |
OMAP4_IOPAD(0x108, PIN_OUTPUT | MUX_MODE1) /* abe_mcbsp3_dx */ |
| 356 |
OMAP4_IOPAD(0x10a, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_clkx */ |
| 357 |
OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_fsx */ |
| 358 |
>; |
| 359 |
}; |
| 360 |
}; |
| 361 |
|
| 362 |
&omap4_pmx_wkup { |
| 363 |
usb_gpio_mux_sel2: usb-gpio-mux-sel2-pins { |
| 364 |
/* gpio_wk0 */ |
| 365 |
pinctrl-single,pins = < |
| 366 |
OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3) |
| 367 |
>; |
| 368 |
}; |
| 369 |
}; |
| 370 |
|
| 371 |
/* RNG is used by secure mode and not accessible */ |
| 372 |
&rng_target { |
| 373 |
status = "disabled"; |
| 374 |
}; |
| 375 |
|
| 376 |
/* |
| 377 |
* The uart1 port is wired to mdm6600 with rts and cts. The modem uses gpio_149 |
| 378 |
* for wake-up events for both the USB PHY and the UART. We can use gpio_149 |
| 379 |
* pad as the shared wakeirq for the UART rather than the RX or CTS pad as we |
| 380 |
* have gpio_149 trigger before the UART transfer starts. |
| 381 |
*/ |
| 382 |
&uart1 { |
| 383 |
pinctrl-names = "default"; |
| 384 |
pinctrl-0 = <&uart1_pins>; |
| 385 |
interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH |
| 386 |
&omap4_pmx_core 0x110>; |
| 387 |
uart-has-rtscts; |
| 388 |
current-speed = <115200>; |
| 389 |
}; |
| 390 |
|
| 391 |
&uart3 { |
| 392 |
interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH |
| 393 |
&omap4_pmx_core 0x17c>; |
| 394 |
overrun-throttle-ms = <500>; |
| 395 |
}; |
| 396 |
|
| 397 |
&uart4 { |
| 398 |
pinctrl-names = "default"; |
| 399 |
pinctrl-0 = <&uart4_pins>; |
| 400 |
|
| 401 |
bluetooth { |
| 402 |
compatible = "ti,wl1285-st"; |
| 403 |
enable-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; /* gpio 174 */ |
| 404 |
max-speed = <3686400>; |
| 405 |
}; |
| 406 |
}; |
| 407 |
|
| 408 |
/* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */ |
| 409 |
&usb_otg_hs { |
| 410 |
interface-type = <1>; |
| 411 |
mode = <3>; |
| 412 |
|
| 413 |
/* |
| 414 |
* Max 300 mA steps based on similar PMIC MC13783UG.pdf "Table 10-4. |
| 415 |
* VBUS Regulator Main Characteristics". Binding uses 2 mA units. |
| 416 |
*/ |
| 417 |
power = <150>; |
| 418 |
}; |
| 419 |
|
| 420 |
&mcbsp2 { |
| 421 |
#sound-dai-cells = <0>; |
| 422 |
pinctrl-names = "default"; |
| 423 |
pinctrl-0 = <&mcbsp2_pins>; |
| 424 |
status = "okay"; |
| 425 |
|
| 426 |
mcbsp2_port: port { |
| 427 |
cpu_dai2: endpoint { |
| 428 |
dai-format = "i2s"; |
| 429 |
remote-endpoint = <&cpcap_audio_codec0>; |
| 430 |
frame-master = <&cpcap_audio_codec0>; |
| 431 |
bitclock-master = <&cpcap_audio_codec0>; |
| 432 |
}; |
| 433 |
}; |
| 434 |
}; |
| 435 |
|
| 436 |
&mcbsp3 { |
| 437 |
#sound-dai-cells = <0>; |
| 438 |
pinctrl-names = "default"; |
| 439 |
pinctrl-0 = <&mcbsp3_pins>; |
| 440 |
status = "okay"; |
| 441 |
|
| 442 |
mcbsp3_port: port { |
| 443 |
cpu_dai3: endpoint { |
| 444 |
dai-format = "dsp_a"; |
| 445 |
frame-master = <&cpcap_audio_codec1>; |
| 446 |
bitclock-master = <&cpcap_audio_codec1>; |
| 447 |
remote-endpoint = <&cpcap_audio_codec1>; |
| 448 |
}; |
| 449 |
}; |
| 450 |
}; |
| 451 |
|
| 452 |
&cpcap_audio_codec0 { |
| 453 |
remote-endpoint = <&cpu_dai2>; |
| 454 |
}; |
| 455 |
|
| 456 |
&cpcap_audio_codec1 { |
| 457 |
remote-endpoint = <&cpu_dai3>; |
| 458 |
}; |