| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Common support for CompuLab SB-T35 used on SBC-T3530, SBC-T3517 and SBC-T3730 |
| 4 |
*/ |
| 5 |
|
| 6 |
/ { |
| 7 |
tfp410: encoder { |
| 8 |
compatible = "ti,tfp410"; |
| 9 |
|
| 10 |
powerdown-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; /* gpio_54 */ |
| 11 |
|
| 12 |
pinctrl-names = "default"; |
| 13 |
pinctrl-0 = <&tfp410_pins>; |
| 14 |
|
| 15 |
ports { |
| 16 |
#address-cells = <1>; |
| 17 |
#size-cells = <0>; |
| 18 |
|
| 19 |
port@0 { |
| 20 |
reg = <0>; |
| 21 |
|
| 22 |
tfp410_in: endpoint { |
| 23 |
remote-endpoint = <&dpi_out>; |
| 24 |
}; |
| 25 |
}; |
| 26 |
|
| 27 |
port@1 { |
| 28 |
reg = <1>; |
| 29 |
|
| 30 |
tfp410_out: endpoint { |
| 31 |
remote-endpoint = <&dvi_connector_in>; |
| 32 |
}; |
| 33 |
}; |
| 34 |
}; |
| 35 |
}; |
| 36 |
|
| 37 |
dvi0: dvi-connector { |
| 38 |
compatible = "dvi-connector"; |
| 39 |
label = "dvi"; |
| 40 |
|
| 41 |
port { |
| 42 |
dvi_connector_in: endpoint { |
| 43 |
remote-endpoint = <&tfp410_out>; |
| 44 |
}; |
| 45 |
}; |
| 46 |
}; |
| 47 |
|
| 48 |
audio_amp: audio_amp { |
| 49 |
compatible = "regulator-fixed"; |
| 50 |
regulator-name = "audio_amp"; |
| 51 |
pinctrl-names = "default"; |
| 52 |
pinctrl-0 = <&sb_t35_audio_amp>; |
| 53 |
gpio = <&gpio2 29 GPIO_ACTIVE_LOW>; /* gpio_61 */ |
| 54 |
regulator-always-on; |
| 55 |
}; |
| 56 |
}; |
| 57 |
|
| 58 |
&omap3_pmx_core { |
| 59 |
smsc2_pins: smsc2-pins { |
| 60 |
pinctrl-single,pins = < |
| 61 |
OMAP3_CORE1_IOPAD(0x20b6, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs4.gpmc_ncs4 */ |
| 62 |
OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_wait3.gpio_65 */ |
| 63 |
>; |
| 64 |
}; |
| 65 |
|
| 66 |
tfp410_pins: tfp410-pins { |
| 67 |
pinctrl-single,pins = < |
| 68 |
OMAP3_CORE1_IOPAD(0x20b4, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs3.gpio_54 */ |
| 69 |
>; |
| 70 |
}; |
| 71 |
|
| 72 |
i2c3_pins: i2c3-pins { |
| 73 |
pinctrl-single,pins = < |
| 74 |
OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */ |
| 75 |
OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */ |
| 76 |
>; |
| 77 |
}; |
| 78 |
|
| 79 |
sb_t35_audio_amp: sb-t35-audio-amp-pins { |
| 80 |
pinctrl-single,pins = < |
| 81 |
OMAP3_CORE1_IOPAD(0x20c8, PIN_OUTPUT | MUX_MODE4) /* gpmc_nbe1.gpio_61 */ |
| 82 |
>; |
| 83 |
}; |
| 84 |
}; |
| 85 |
|
| 86 |
&i2c3 { |
| 87 |
pinctrl-names = "default"; |
| 88 |
pinctrl-0 = <&i2c3_pins>; |
| 89 |
|
| 90 |
clock-frequency = <400000>; |
| 91 |
|
| 92 |
eeprom@50 { |
| 93 |
compatible = "atmel,24c02"; |
| 94 |
pagesize = <16>; |
| 95 |
reg = <0x50>; |
| 96 |
}; |
| 97 |
}; |
| 98 |
|
| 99 |
&gpmc { |
| 100 |
ranges = <4 0 0x2d000000 0x01000000>; |
| 101 |
|
| 102 |
smsc2: ethernet@4,0 { |
| 103 |
compatible = "smsc,lan9221", "smsc,lan9115"; |
| 104 |
pinctrl-names = "default"; |
| 105 |
pinctrl-0 = <&smsc2_pins>; |
| 106 |
interrupt-parent = <&gpio3>; |
| 107 |
interrupts = <1 IRQ_TYPE_LEVEL_LOW>; |
| 108 |
reg = <4 0 0xff>; |
| 109 |
bank-width = <2>; |
| 110 |
gpmc,device-width = <1>; |
| 111 |
gpmc,cycle2cycle-samecsen; |
| 112 |
gpmc,cycle2cycle-diffcsen; |
| 113 |
gpmc,cs-on-ns = <5>; |
| 114 |
gpmc,cs-rd-off-ns = <150>; |
| 115 |
gpmc,cs-wr-off-ns = <150>; |
| 116 |
gpmc,adv-on-ns = <0>; |
| 117 |
gpmc,adv-rd-off-ns = <15>; |
| 118 |
gpmc,adv-wr-off-ns = <40>; |
| 119 |
gpmc,oe-on-ns = <45>; |
| 120 |
gpmc,oe-off-ns = <140>; |
| 121 |
gpmc,we-on-ns = <45>; |
| 122 |
gpmc,we-off-ns = <140>; |
| 123 |
gpmc,rd-cycle-ns = <155>; |
| 124 |
gpmc,wr-cycle-ns = <155>; |
| 125 |
gpmc,access-ns = <120>; |
| 126 |
gpmc,page-burst-access-ns = <20>; |
| 127 |
gpmc,bus-turnaround-ns = <75>; |
| 128 |
gpmc,cycle2cycle-delay-ns = <75>; |
| 129 |
gpmc,wait-monitoring-ns = <0>; |
| 130 |
gpmc,clk-activation-ns = <0>; |
| 131 |
gpmc,wr-data-mux-bus-ns = <0>; |
| 132 |
gpmc,wr-access-ns = <0>; |
| 133 |
vddvario-supply = <&vddvario>; |
| 134 |
vdd33a-supply = <&vdd33a>; |
| 135 |
reg-io-width = <4>; |
| 136 |
smsc,save-mac-address; |
| 137 |
}; |
| 138 |
}; |