| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Device Tree Source for am3517 SoC |
| 4 |
* |
| 5 |
* Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/ |
| 6 |
*/ |
| 7 |
|
| 8 |
#include "omap3.dtsi" |
| 9 |
|
| 10 |
/* AM3517 doesn't appear to have the crypto engines defined in omap3.dtsi */ |
| 11 |
/delete-node/ &aes1_target; |
| 12 |
/delete-node/ &aes2_target; |
| 13 |
|
| 14 |
/ { |
| 15 |
aliases { |
| 16 |
serial3 = &uart4; |
| 17 |
can = &hecc; |
| 18 |
ethernet = &davinci_emac; |
| 19 |
}; |
| 20 |
|
| 21 |
cpus { |
| 22 |
cpu: cpu@0 { |
| 23 |
/* Based on OMAP3630 variants OPP50 and OPP100 */ |
| 24 |
operating-points-v2 = <&cpu0_opp_table>; |
| 25 |
|
| 26 |
clock-latency = <300000>; /* From legacy driver */ |
| 27 |
}; |
| 28 |
}; |
| 29 |
|
| 30 |
cpu0_opp_table: opp-table { |
| 31 |
compatible = "operating-points-v2-ti-cpu"; |
| 32 |
syscon = <&scm_conf>; |
| 33 |
/* |
| 34 |
* AM3517 TRM only lists 600MHz @ 1.2V, but omap36xx |
| 35 |
* appear to operate at 300MHz as well. Since AM3517 only |
| 36 |
* lists one operating voltage, it will remain fixed at 1.2V |
| 37 |
*/ |
| 38 |
opp-50-300000000 { |
| 39 |
/* OPP50 */ |
| 40 |
opp-hz = /bits/ 64 <300000000>; |
| 41 |
opp-microvolt = <1200000>; |
| 42 |
opp-supported-hw = <0xffffffff 0xffffffff>; |
| 43 |
opp-suspend; |
| 44 |
}; |
| 45 |
|
| 46 |
opp-100-600000000 { |
| 47 |
/* OPP100 */ |
| 48 |
opp-hz = /bits/ 64 <600000000>; |
| 49 |
opp-microvolt = <1200000>; |
| 50 |
opp-supported-hw = <0xffffffff 0xffffffff>; |
| 51 |
}; |
| 52 |
}; |
| 53 |
|
| 54 |
ocp@68000000 { |
| 55 |
target-module@5c040000 { |
| 56 |
compatible = "ti,sysc-omap2", "ti,sysc"; |
| 57 |
reg = <0x5c040400 0x4>, |
| 58 |
<0x5c040404 0x4>, |
| 59 |
<0x5c040408 0x4>; |
| 60 |
reg-names = "rev", "sysc", "syss"; |
| 61 |
ti,sysc-mask = <(SYSC_OMAP2_ENAWAKEUP | |
| 62 |
SYSC_OMAP2_SOFTRESET | |
| 63 |
SYSC_OMAP2_AUTOIDLE)>; |
| 64 |
ti,sysc-midle = <SYSC_IDLE_FORCE>, |
| 65 |
<SYSC_IDLE_NO>, |
| 66 |
<SYSC_IDLE_SMART>; |
| 67 |
ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| 68 |
<SYSC_IDLE_NO>, |
| 69 |
<SYSC_IDLE_SMART>; |
| 70 |
ti,syss-mask = <1>; |
| 71 |
clocks = <&hsotgusb_ick_am35xx>; |
| 72 |
clock-names = "fck"; |
| 73 |
#address-cells = <1>; |
| 74 |
#size-cells = <1>; |
| 75 |
ranges = <0x0 0x5c040000 0x1000>; |
| 76 |
|
| 77 |
am35x_otg_hs: am35x_otg_hs@0 { |
| 78 |
compatible = "ti,omap3-musb"; |
| 79 |
status = "disabled"; |
| 80 |
reg = <0 0x1000>; |
| 81 |
interrupts = <71>; |
| 82 |
interrupt-names = "mc"; |
| 83 |
}; |
| 84 |
}; |
| 85 |
|
| 86 |
davinci_emac: ethernet@5c000000 { |
| 87 |
compatible = "ti,am3517-emac"; |
| 88 |
ti,hwmods = "davinci_emac"; |
| 89 |
status = "disabled"; |
| 90 |
reg = <0x5c000000 0x30000>; |
| 91 |
interrupts = <67 68 69 70>; |
| 92 |
syscon = <&scm_conf>; |
| 93 |
ti,davinci-ctrl-reg-offset = <0x10000>; |
| 94 |
ti,davinci-ctrl-mod-reg-offset = <0>; |
| 95 |
ti,davinci-ctrl-ram-offset = <0x20000>; |
| 96 |
ti,davinci-ctrl-ram-size = <0x2000>; |
| 97 |
ti,davinci-rmii-en = /bits/ 8 <1>; |
| 98 |
local-mac-address = [ 00 00 00 00 00 00 ]; |
| 99 |
clocks = <&emac_ick>; |
| 100 |
clock-names = "ick"; |
| 101 |
}; |
| 102 |
|
| 103 |
davinci_mdio: mdio@5c030000 { |
| 104 |
compatible = "ti,davinci_mdio"; |
| 105 |
ti,hwmods = "davinci_mdio"; |
| 106 |
status = "disabled"; |
| 107 |
reg = <0x5c030000 0x1000>; |
| 108 |
bus_freq = <1000000>; |
| 109 |
#address-cells = <1>; |
| 110 |
#size-cells = <0>; |
| 111 |
clocks = <&emac_fck>; |
| 112 |
clock-names = "fck"; |
| 113 |
}; |
| 114 |
|
| 115 |
uart4: serial@4809e000 { |
| 116 |
compatible = "ti,omap3-uart"; |
| 117 |
ti,hwmods = "uart4"; |
| 118 |
status = "disabled"; |
| 119 |
reg = <0x4809e000 0x400>; |
| 120 |
interrupts = <84>; |
| 121 |
dmas = <&sdma 55 &sdma 54>; |
| 122 |
dma-names = "tx", "rx"; |
| 123 |
clock-frequency = <48000000>; |
| 124 |
}; |
| 125 |
|
| 126 |
omap3_pmx_core2: pinmux@480025d8 { |
| 127 |
compatible = "ti,omap3-padconf", "pinctrl-single"; |
| 128 |
reg = <0x480025d8 0x24>; |
| 129 |
#address-cells = <1>; |
| 130 |
#size-cells = <0>; |
| 131 |
#pinctrl-cells = <1>; |
| 132 |
#interrupt-cells = <1>; |
| 133 |
interrupt-controller; |
| 134 |
pinctrl-single,register-width = <16>; |
| 135 |
pinctrl-single,function-mask = <0xff1f>; |
| 136 |
}; |
| 137 |
|
| 138 |
hecc: can@5c050000 { |
| 139 |
compatible = "ti,am3517-hecc"; |
| 140 |
status = "disabled"; |
| 141 |
reg = <0x5c050000 0x80>, |
| 142 |
<0x5c053000 0x180>, |
| 143 |
<0x5c052000 0x200>; |
| 144 |
reg-names = "hecc", "hecc-ram", "mbx"; |
| 145 |
interrupts = <24>; |
| 146 |
clocks = <&hecc_ck>; |
| 147 |
}; |
| 148 |
|
| 149 |
/* |
| 150 |
* On am3517 the OCP registers do not seem to be accessible |
| 151 |
* similar to the omap34xx. Maybe SGX is permanently set to |
| 152 |
* "OCP bypass mode", or maybe there is OCP_SYSCONFIG that is |
| 153 |
* write-only at 0x50000e10. We detect SGX based on the SGX |
| 154 |
* revision register instead of the unreadable OCP revision |
| 155 |
* register. |
| 156 |
*/ |
| 157 |
sgx_module: target-module@50000000 { |
| 158 |
compatible = "ti,sysc-omap2", "ti,sysc"; |
| 159 |
reg = <0x50000014 0x4>; |
| 160 |
reg-names = "rev"; |
| 161 |
clocks = <&sgx_fck>, <&sgx_ick>; |
| 162 |
clock-names = "fck", "ick"; |
| 163 |
#address-cells = <1>; |
| 164 |
#size-cells = <1>; |
| 165 |
ranges = <0 0x50000000 0x10000>; |
| 166 |
|
| 167 |
gpu@0 { |
| 168 |
compatible = "ti,omap3430-gpu", "img,powervr-sgx530"; |
| 169 |
reg = <0x0 0x10000>; /* 64kB */ |
| 170 |
interrupts = <21>; |
| 171 |
}; |
| 172 |
}; |
| 173 |
}; |
| 174 |
}; |
| 175 |
|
| 176 |
/* Not currently working, probably needs at least different clocks */ |
| 177 |
&rng_target { |
| 178 |
status = "disabled"; |
| 179 |
/delete-property/ clocks; |
| 180 |
}; |
| 181 |
|
| 182 |
/* Table Table 5-79 of the TRM shows 480ab000 is reserved */ |
| 183 |
&usb_otg_target { |
| 184 |
status = "disabled"; |
| 185 |
}; |
| 186 |
|
| 187 |
&iva { |
| 188 |
status = "disabled"; |
| 189 |
}; |
| 190 |
|
| 191 |
&mailbox { |
| 192 |
status = "disabled"; |
| 193 |
}; |
| 194 |
|
| 195 |
&mmu_isp { |
| 196 |
status = "disabled"; |
| 197 |
}; |
| 198 |
|
| 199 |
#include "am35xx-clocks.dtsi" |
| 200 |
#include "omap36xx-am35xx-omap3430es2plus-clocks.dtsi" |
| 201 |
|
| 202 |
/* Preferred always-on timer for clocksource */ |
| 203 |
&timer1_target { |
| 204 |
ti,no-reset-on-init; |
| 205 |
ti,no-idle; |
| 206 |
timer@0 { |
| 207 |
assigned-clocks = <&gpt1_fck>; |
| 208 |
assigned-clock-parents = <&sys_ck>; |
| 209 |
}; |
| 210 |
}; |
| 211 |
|
| 212 |
/* Preferred timer for clockevent */ |
| 213 |
&timer2_target { |
| 214 |
ti,no-reset-on-init; |
| 215 |
ti,no-idle; |
| 216 |
timer@0 { |
| 217 |
assigned-clocks = <&gpt2_fck>; |
| 218 |
assigned-clock-parents = <&sys_ck>; |
| 219 |
}; |
| 220 |
}; |