| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/ |
| 4 |
*/ |
| 5 |
/dts-v1/; |
| 6 |
|
| 7 |
#include "am33xx.dtsi" |
| 8 |
#include "am335x-bone-common.dtsi" |
| 9 |
#include "am335x-bonegreen-common.dtsi" |
| 10 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
model = "TI AM335x BeagleBone Green Wireless"; |
| 14 |
compatible = "ti,am335x-bone-green-wireless", "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; |
| 15 |
|
| 16 |
wlan_en_reg: fixedregulator@2 { |
| 17 |
compatible = "regulator-fixed"; |
| 18 |
regulator-name = "wlan-en-regulator"; |
| 19 |
regulator-min-microvolt = <1800000>; |
| 20 |
regulator-max-microvolt = <1800000>; |
| 21 |
startup-delay-us = <70000>; |
| 22 |
|
| 23 |
/* WL_EN */ |
| 24 |
gpio = <&gpio0 26 0>; |
| 25 |
enable-active-high; |
| 26 |
}; |
| 27 |
}; |
| 28 |
|
| 29 |
&am33xx_pinmux { |
| 30 |
bt_pins: bt-pins { |
| 31 |
pinctrl-single,pins = < |
| 32 |
AM33XX_PADCONF(AM335X_PIN_GPMC_BEN1, PIN_OUTPUT_PULLUP, MUX_MODE7) /* gpmc_ad12.gpio1_28 BT_EN */ |
| 33 |
>; |
| 34 |
}; |
| 35 |
|
| 36 |
mmc3_pins: mmc3-pins { |
| 37 |
pinctrl-single,pins = < |
| 38 |
AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT_PULLUP, MUX_MODE3) /* gpmc_ad12.mmc2_dat0 */ |
| 39 |
AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT_PULLUP, MUX_MODE3) /* gpmc_ad13.mmc2_dat1 */ |
| 40 |
AM33XX_PADCONF(AM335X_PIN_GPMC_AD14, PIN_INPUT_PULLUP, MUX_MODE3) /* gpmc_ad14.mmc2_dat2 */ |
| 41 |
AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_INPUT_PULLUP, MUX_MODE3) /* gpmc_ad15.mmc2_dat3 */ |
| 42 |
AM33XX_PADCONF(AM335X_PIN_GPMC_CSN3, PIN_INPUT_PULLUP, MUX_MODE3) /* gpmc_csn3.mmc2_cmd */ |
| 43 |
AM33XX_PADCONF(AM335X_PIN_GPMC_CLK, PIN_INPUT_PULLUP, MUX_MODE3) /* gpmc_clk.mmc2_clk */ |
| 44 |
>; |
| 45 |
}; |
| 46 |
|
| 47 |
uart3_pins: uart3-pins { |
| 48 |
pinctrl-single,pins = < |
| 49 |
AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLUP, MUX_MODE1) /* gmii1_rxd3.uart3_rxd */ |
| 50 |
AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE1) /* gmii1_rxd2.uart3_txd */ |
| 51 |
AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT, MUX_MODE3) /* mdio_data.uart3_ctsn */ |
| 52 |
AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLDOWN, MUX_MODE3) /* mdio_clk.uart3_rtsn */ |
| 53 |
>; |
| 54 |
}; |
| 55 |
|
| 56 |
wl18xx_pins: wl18xx-pins { |
| 57 |
pinctrl-single,pins = < |
| 58 |
AM33XX_PADCONF(AM335X_PIN_GPMC_AD10, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gpmc_ad10.gpio0_26 WL_EN */ |
| 59 |
AM33XX_PADCONF(AM335X_PIN_GPMC_AD11, PIN_INPUT_PULLDOWN, MUX_MODE7) /* gpmc_ad11.gpio0_27 WL_IRQ */ |
| 60 |
AM33XX_PADCONF(AM335X_PIN_GPMC_CSN0, PIN_OUTPUT_PULLUP, MUX_MODE7) /* gpmc_csn0.gpio1_29 LS_BUF_EN */ |
| 61 |
>; |
| 62 |
}; |
| 63 |
}; |
| 64 |
|
| 65 |
&mac_sw { |
| 66 |
status = "disabled"; |
| 67 |
}; |
| 68 |
|
| 69 |
&mmc3 { |
| 70 |
dmas = <&edma_xbar 12 0 1 |
| 71 |
&edma_xbar 13 0 2>; |
| 72 |
dma-names = "tx", "rx"; |
| 73 |
status = "okay"; |
| 74 |
vmmc-supply = <&wlan_en_reg>; |
| 75 |
bus-width = <4>; |
| 76 |
non-removable; |
| 77 |
cap-power-off-card; |
| 78 |
keep-power-in-suspend; |
| 79 |
pinctrl-names = "default"; |
| 80 |
pinctrl-0 = <&mmc3_pins &wl18xx_pins>; |
| 81 |
|
| 82 |
#address-cells = <1>; |
| 83 |
#size-cells = <0>; |
| 84 |
wlcore: wlcore@2 { |
| 85 |
compatible = "ti,wl1835"; |
| 86 |
reg = <2>; |
| 87 |
interrupt-parent = <&gpio0>; |
| 88 |
interrupts = <27 IRQ_TYPE_EDGE_RISING>; |
| 89 |
}; |
| 90 |
}; |
| 91 |
|
| 92 |
&uart3 { |
| 93 |
pinctrl-names = "default"; |
| 94 |
pinctrl-0 = <&uart3_pins &bt_pins>; |
| 95 |
status = "okay"; |
| 96 |
|
| 97 |
bluetooth { |
| 98 |
compatible = "ti,wl1835-st"; |
| 99 |
enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; |
| 100 |
}; |
| 101 |
}; |
| 102 |
|
| 103 |
&gpio1 { |
| 104 |
ls-buf-en-hog { |
| 105 |
gpio-hog; |
| 106 |
gpios = <29 GPIO_ACTIVE_HIGH>; |
| 107 |
output-high; |
| 108 |
line-name = "LS_BUF_EN"; |
| 109 |
}; |
| 110 |
}; |
| 111 |
|
| 112 |
/* BT_AUD_OUT from wl1835 has to be pulled low when WL_EN is activated.*/ |
| 113 |
/* in case it isn't, wilink8 ends up in one of the test modes that */ |
| 114 |
/* intruces various issues (elp wkaeup timeouts etc.) */ |
| 115 |
/* On the BBGW this pin is routed through the level shifter (U21) that */ |
| 116 |
/* introduces a pullup on the line and wilink8 ends up in a bad state. */ |
| 117 |
/* use a gpio hog to force this pin low. An alternative may be adding */ |
| 118 |
/* an external pulldown on U21 pin 4. */ |
| 119 |
|
| 120 |
&gpio3 { |
| 121 |
bt-aud-in-hog { |
| 122 |
gpio-hog; |
| 123 |
gpios = <16 GPIO_ACTIVE_HIGH>; |
| 124 |
output-low; |
| 125 |
line-name = "MCASP0_AHCLKR"; |
| 126 |
}; |
| 127 |
}; |