| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
|
| 3 |
/dts-v1/; |
| 4 |
|
| 5 |
#include "omap36xx.dtsi" |
| 6 |
#include "logicpd-torpedo-som.dtsi" |
| 7 |
#include "omap-gpmc-smsc9221.dtsi" |
| 8 |
#include "logicpd-torpedo-baseboard.dtsi" |
| 9 |
|
| 10 |
/ { |
| 11 |
model = "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit"; |
| 12 |
compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3"; |
| 13 |
|
| 14 |
wl12xx_vmmc: wl12xx_vmmc { |
| 15 |
compatible = "regulator-fixed"; |
| 16 |
regulator-name = "vwl1271"; |
| 17 |
regulator-min-microvolt = <1800000>; |
| 18 |
regulator-max-microvolt = <1800000>; |
| 19 |
gpio = <&gpio5 29 0>; /* gpio157 */ |
| 20 |
startup-delay-us = <70000>; |
| 21 |
enable-active-high; |
| 22 |
vin-supply = <&vmmc2>; |
| 23 |
}; |
| 24 |
}; |
| 25 |
|
| 26 |
/* |
| 27 |
* Only found on the wireless SOM. For the SOM without wireless, the pins for |
| 28 |
* MMC3 can be routed with jumpers to the second MMC slot on the devkit and |
| 29 |
* gpio157 is not connected. So this should be OK to keep common for now, |
| 30 |
* probably device tree overlays is the way to go with the various SOM and |
| 31 |
* jumpering combinations for the long run. |
| 32 |
*/ |
| 33 |
&mmc3 { |
| 34 |
interrupts-extended = <&intc 94 &omap3_pmx_core 0x136>; |
| 35 |
pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>; |
| 36 |
pinctrl-names = "default"; |
| 37 |
vmmc-supply = <&wl12xx_vmmc>; |
| 38 |
non-removable; |
| 39 |
bus-width = <4>; |
| 40 |
cap-power-off-card; |
| 41 |
#address-cells = <1>; |
| 42 |
#size-cells = <0>; |
| 43 |
wlcore: wlcore@2 { |
| 44 |
compatible = "ti,wl1283"; |
| 45 |
reg = <2>; |
| 46 |
interrupt-parent = <&gpio5>; |
| 47 |
interrupts = <24 IRQ_TYPE_EDGE_RISING>; /* gpio 152 */ |
| 48 |
ref-clock-frequency = <26000000>; |
| 49 |
tcxo-clock-frequency = <26000000>; |
| 50 |
}; |
| 51 |
}; |
| 52 |
|
| 53 |
&uart2 { |
| 54 |
/delete-property/dma-names; |
| 55 |
bluetooth-gnss { |
| 56 |
compatible = "ti,wl1283-st"; |
| 57 |
enable-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* gpio 162 */ |
| 58 |
max-speed = <3000000>; |
| 59 |
}; |
| 60 |
}; |
| 61 |
|
| 62 |
/* The DM3730 has a faster L3 than OMAP35, so increase pixel clock */ |
| 63 |
&mt9p031_out { |
| 64 |
pixel-clock-frequency = <90000000>; |
| 65 |
}; |
| 66 |
|
| 67 |
&omap3_pmx_core { |
| 68 |
mmc3_pins: mm3-pins { |
| 69 |
pinctrl-single,pins = < |
| 70 |
OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */ |
| 71 |
OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */ |
| 72 |
OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */ |
| 73 |
OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */ |
| 74 |
OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ |
| 75 |
OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */ |
| 76 |
>; |
| 77 |
}; |
| 78 |
}; |
| 79 |
|
| 80 |
&omap3_pmx_core2 { |
| 81 |
mmc3_core2_pins: mmc3-core2-pins { |
| 82 |
pinctrl-single,pins = < |
| 83 |
OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */ |
| 84 |
OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */ |
| 85 |
>; |
| 86 |
}; |
| 87 |
}; |
| 88 |
|
| 89 |
/* The gpio muxing between omap3530 and dm3730 is different for GPIO_128 */ |
| 90 |
&omap3_pmx_wkup { |
| 91 |
isp1763_pins: isp1763-pins { |
| 92 |
pinctrl-single,pins = < |
| 93 |
OMAP3_WKUP_IOPAD(0x2a58, PIN_INPUT_PULLUP | MUX_MODE4) /* reserved.gpio_128 */ |
| 94 |
>; |
| 95 |
}; |
| 96 |
}; |