| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Copyright (C) 2015 CompuLab, Ltd. - https://www.compulab.co.il/ |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
|
| 8 |
#include <dt-bindings/pinctrl/am43xx.h> |
| 9 |
#include <dt-bindings/gpio/gpio.h> |
| 10 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 11 |
#include "am4372.dtsi" |
| 12 |
|
| 13 |
/ { |
| 14 |
model = "CompuLab CM-T43"; |
| 15 |
compatible = "compulab,am437x-cm-t43", "ti,am4372", "ti,am43"; |
| 16 |
|
| 17 |
leds { |
| 18 |
compatible = "gpio-leds"; |
| 19 |
|
| 20 |
ledb { |
| 21 |
label = "cm-t43:green"; |
| 22 |
gpios = <&gpio0 24 GPIO_ACTIVE_HIGH>; |
| 23 |
linux,default-trigger = "heartbeat"; |
| 24 |
}; |
| 25 |
}; |
| 26 |
|
| 27 |
vmmc_3v3: fixedregulator-v3_3 { |
| 28 |
compatible = "regulator-fixed"; |
| 29 |
regulator-name = "vmmc_3v3"; |
| 30 |
regulator-min-microvolt = <3300000>; |
| 31 |
regulator-max-microvolt = <3300000>; |
| 32 |
regulator-always-on; |
| 33 |
enable-active-high; |
| 34 |
}; |
| 35 |
}; |
| 36 |
|
| 37 |
&am43xx_pinmux { |
| 38 |
pinctrl-names = "default"; |
| 39 |
pinctrl-0 = <&cm_t43_led_pins>; |
| 40 |
|
| 41 |
cm_t43_led_pins: cm-t43-led-pins { |
| 42 |
pinctrl-single,pins = < |
| 43 |
AM4372_IOPAD(0xa78, MUX_MODE7) |
| 44 |
>; |
| 45 |
}; |
| 46 |
|
| 47 |
i2c0_pins: i2c0-pins { |
| 48 |
pinctrl-single,pins = < |
| 49 |
AM4372_IOPAD(0x988, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */ |
| 50 |
AM4372_IOPAD(0x98c, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ |
| 51 |
>; |
| 52 |
}; |
| 53 |
|
| 54 |
emmc_pins: emmc-pins { |
| 55 |
pinctrl-single,pins = < |
| 56 |
AM4372_IOPAD(0x820, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad8.mmc1_dat0 */ |
| 57 |
AM4372_IOPAD(0x824, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad9.mmc1_dat1 */ |
| 58 |
AM4372_IOPAD(0x828, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad10.mmc1_dat2 */ |
| 59 |
AM4372_IOPAD(0x82c, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad11.mmc1_dat3 */ |
| 60 |
AM4372_IOPAD(0x830, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad12.mmc1_dat4 */ |
| 61 |
AM4372_IOPAD(0x834, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad13.mmc1_dat5 */ |
| 62 |
AM4372_IOPAD(0x838, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad14.mmc1_dat6 */ |
| 63 |
AM4372_IOPAD(0x83c, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_ad15.mmc1_dat7 */ |
| 64 |
AM4372_IOPAD(0x880, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ |
| 65 |
AM4372_IOPAD(0x884, PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ |
| 66 |
>; |
| 67 |
}; |
| 68 |
|
| 69 |
spi0_pins: spi0-pins { |
| 70 |
pinctrl-single,pins = < |
| 71 |
AM4372_IOPAD(0x950, PIN_INPUT | MUX_MODE0) /* spi0_sclk.spi0_sclk */ |
| 72 |
AM4372_IOPAD(0x954, PIN_INPUT | MUX_MODE0) /* spi0_d0.spi0_d0 */ |
| 73 |
AM4372_IOPAD(0x958, PIN_OUTPUT | MUX_MODE0) /* spi0_d1.spi0_d1 */ |
| 74 |
AM4372_IOPAD(0x95C, PIN_OUTPUT | MUX_MODE0) /* spi0_cs0.spi0_cs0 */ |
| 75 |
>; |
| 76 |
}; |
| 77 |
|
| 78 |
nand_flash_x8: nand-flash-x8-pins { |
| 79 |
pinctrl-single,pins = < |
| 80 |
AM4372_IOPAD(0x800, PIN_INPUT | PULL_DISABLE | MUX_MODE0) |
| 81 |
AM4372_IOPAD(0x804, PIN_INPUT | PULL_DISABLE | MUX_MODE0) |
| 82 |
AM4372_IOPAD(0x808, PIN_INPUT | PULL_DISABLE | MUX_MODE0) |
| 83 |
AM4372_IOPAD(0x80c, PIN_INPUT | PULL_DISABLE | MUX_MODE0) |
| 84 |
AM4372_IOPAD(0x810, PIN_INPUT | PULL_DISABLE | MUX_MODE0) |
| 85 |
AM4372_IOPAD(0x814, PIN_INPUT | PULL_DISABLE | MUX_MODE0) |
| 86 |
AM4372_IOPAD(0x818, PIN_INPUT | PULL_DISABLE | MUX_MODE0) |
| 87 |
AM4372_IOPAD(0x81c, PIN_INPUT | PULL_DISABLE | MUX_MODE0) |
| 88 |
AM4372_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE0) |
| 89 |
AM4372_IOPAD(0x874, PIN_OUTPUT_PULLUP | MUX_MODE0) |
| 90 |
AM4372_IOPAD(0x87c, PIN_OUTPUT_PULLUP | MUX_MODE0) |
| 91 |
AM4372_IOPAD(0x898, PIN_OUTPUT_PULLDOWN | MUX_MODE0) |
| 92 |
AM4372_IOPAD(0x894, PIN_OUTPUT_PULLDOWN | MUX_MODE0) |
| 93 |
AM4372_IOPAD(0x890, PIN_OUTPUT_PULLDOWN | MUX_MODE0) |
| 94 |
AM4372_IOPAD(0x89c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) |
| 95 |
>; |
| 96 |
}; |
| 97 |
|
| 98 |
cpsw_default: cpsw-default-pins { |
| 99 |
pinctrl-single,pins = < |
| 100 |
/* Slave 1 */ |
| 101 |
AM4372_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_txen */ |
| 102 |
AM4372_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxdv.rgmii1_rxctl */ |
| 103 |
AM4372_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_txd3 */ |
| 104 |
AM4372_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_txd2 */ |
| 105 |
AM4372_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_txd1 */ |
| 106 |
AM4372_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_txd0 */ |
| 107 |
AM4372_IOPAD(0x92c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txclk.rmii1_tclk */ |
| 108 |
AM4372_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxclk.rmii1_rclk */ |
| 109 |
AM4372_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rxd3 */ |
| 110 |
AM4372_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rxd2 */ |
| 111 |
AM4372_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rxd1 */ |
| 112 |
AM4372_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rxd0 */ |
| 113 |
AM4372_IOPAD(0xa74, MUX_MODE3) |
| 114 |
/* Slave 2 */ |
| 115 |
AM4372_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a0.txen */ |
| 116 |
AM4372_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rxctl */ |
| 117 |
AM4372_IOPAD(0x848, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.txd3 */ |
| 118 |
AM4372_IOPAD(0x84c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.txd2 */ |
| 119 |
AM4372_IOPAD(0x850, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.txd1 */ |
| 120 |
AM4372_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.txd0 */ |
| 121 |
AM4372_IOPAD(0x858, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a6.tclk */ |
| 122 |
AM4372_IOPAD(0x85c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rclk */ |
| 123 |
AM4372_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rxd3 */ |
| 124 |
AM4372_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rxd2 */ |
| 125 |
AM4372_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rxd1 */ |
| 126 |
AM4372_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rxd0 */ |
| 127 |
AM4372_IOPAD(0xa38, MUX_MODE7) |
| 128 |
>; |
| 129 |
}; |
| 130 |
|
| 131 |
davinci_mdio_default: davinci-mdio-default-pins { |
| 132 |
pinctrl-single,pins = < |
| 133 |
/* MDIO */ |
| 134 |
AM4372_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ |
| 135 |
AM4372_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ |
| 136 |
>; |
| 137 |
}; |
| 138 |
}; |
| 139 |
|
| 140 |
&gpmc { |
| 141 |
status = "okay"; |
| 142 |
pinctrl-names = "default"; |
| 143 |
pinctrl-0 = <&nand_flash_x8>; |
| 144 |
ranges = <0 0 0x08000000 0x1000000>; |
| 145 |
nand@0,0 { |
| 146 |
compatible = "ti,omap2-nand"; |
| 147 |
reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ |
| 148 |
interrupt-parent = <&gpmc>; |
| 149 |
interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ |
| 150 |
<1 IRQ_TYPE_NONE>; /* termcount */ |
| 151 |
ti,nand-ecc-opt = "bch8"; |
| 152 |
ti,elm-id = <&elm>; |
| 153 |
|
| 154 |
nand-bus-width = <8>; |
| 155 |
gpmc,device-width = <1>; |
| 156 |
gpmc,sync-clk-ps = <0>; |
| 157 |
gpmc,cs-on-ns = <0>; |
| 158 |
gpmc,cs-rd-off-ns = <44>; |
| 159 |
gpmc,cs-wr-off-ns = <44>; |
| 160 |
gpmc,adv-on-ns = <6>; |
| 161 |
gpmc,adv-rd-off-ns = <34>; |
| 162 |
gpmc,adv-wr-off-ns = <44>; |
| 163 |
gpmc,we-on-ns = <0>; |
| 164 |
gpmc,we-off-ns = <40>; |
| 165 |
gpmc,oe-on-ns = <0>; |
| 166 |
gpmc,oe-off-ns = <54>; |
| 167 |
gpmc,access-ns = <64>; |
| 168 |
gpmc,rd-cycle-ns = <82>; |
| 169 |
gpmc,wr-cycle-ns = <82>; |
| 170 |
gpmc,bus-turnaround-ns = <0>; |
| 171 |
gpmc,cycle2cycle-delay-ns = <0>; |
| 172 |
gpmc,clk-activation-ns = <0>; |
| 173 |
gpmc,wr-access-ns = <40>; |
| 174 |
gpmc,wr-data-mux-bus-ns = <0>; |
| 175 |
|
| 176 |
#address-cells = <1>; |
| 177 |
#size-cells = <1>; |
| 178 |
/* MTD partition table */ |
| 179 |
partition@0 { |
| 180 |
label = "kernel"; |
| 181 |
reg = <0x0 0x00980000>; |
| 182 |
}; |
| 183 |
partition@980000 { |
| 184 |
label = "dtb"; |
| 185 |
reg = <0x00980000 0x00080000>; |
| 186 |
}; |
| 187 |
partition@a00000 { |
| 188 |
label = "rootfs"; |
| 189 |
reg = <0x00a00000 0x0>; |
| 190 |
}; |
| 191 |
}; |
| 192 |
}; |
| 193 |
|
| 194 |
&i2c0 { |
| 195 |
status = "okay"; |
| 196 |
pinctrl-names = "default"; |
| 197 |
pinctrl-0 = <&i2c0_pins>; |
| 198 |
clock-frequency = <100000>; |
| 199 |
|
| 200 |
tps65218: tps65218@24 { |
| 201 |
compatible = "ti,tps65218"; |
| 202 |
reg = <0x24>; |
| 203 |
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* NMIn */ |
| 204 |
interrupt-parent = <&gic>; |
| 205 |
interrupt-controller; |
| 206 |
#interrupt-cells = <2>; |
| 207 |
|
| 208 |
dcdc1: regulator-dcdc1 { |
| 209 |
regulator-name = "vdd_core"; |
| 210 |
regulator-min-microvolt = <912000>; |
| 211 |
regulator-max-microvolt = <1144000>; |
| 212 |
regulator-boot-on; |
| 213 |
regulator-always-on; |
| 214 |
}; |
| 215 |
|
| 216 |
dcdc2: regulator-dcdc2 { |
| 217 |
regulator-name = "vdd_mpu"; |
| 218 |
regulator-min-microvolt = <912000>; |
| 219 |
regulator-max-microvolt = <1378000>; |
| 220 |
regulator-boot-on; |
| 221 |
regulator-always-on; |
| 222 |
}; |
| 223 |
|
| 224 |
dcdc3: regulator-dcdc3 { |
| 225 |
regulator-name = "vdcdc3"; |
| 226 |
regulator-suspend-enable; |
| 227 |
regulator-min-microvolt = <1500000>; |
| 228 |
regulator-max-microvolt = <1500000>; |
| 229 |
regulator-boot-on; |
| 230 |
regulator-always-on; |
| 231 |
}; |
| 232 |
|
| 233 |
dcdc5: regulator-dcdc5 { |
| 234 |
regulator-name = "v1_0bat"; |
| 235 |
regulator-min-microvolt = <1000000>; |
| 236 |
regulator-max-microvolt = <1000000>; |
| 237 |
regulator-boot-on; |
| 238 |
regulator-always-on; |
| 239 |
}; |
| 240 |
|
| 241 |
dcdc6: regulator-dcdc6 { |
| 242 |
regulator-name = "v1_8bat"; |
| 243 |
regulator-min-microvolt = <1800000>; |
| 244 |
regulator-max-microvolt = <1800000>; |
| 245 |
regulator-boot-on; |
| 246 |
regulator-always-on; |
| 247 |
}; |
| 248 |
|
| 249 |
ldo1: regulator-ldo1 { |
| 250 |
regulator-min-microvolt = <1800000>; |
| 251 |
regulator-max-microvolt = <1800000>; |
| 252 |
regulator-boot-on; |
| 253 |
regulator-always-on; |
| 254 |
}; |
| 255 |
}; |
| 256 |
|
| 257 |
eeprom_module: eeprom@50 { |
| 258 |
compatible = "atmel,24c02"; |
| 259 |
reg = <0x50>; |
| 260 |
pagesize = <16>; |
| 261 |
}; |
| 262 |
}; |
| 263 |
|
| 264 |
&gpio0 { |
| 265 |
status = "okay"; |
| 266 |
}; |
| 267 |
|
| 268 |
&gpio1 { |
| 269 |
status = "okay"; |
| 270 |
}; |
| 271 |
|
| 272 |
&gpio2 { |
| 273 |
status = "okay"; |
| 274 |
}; |
| 275 |
|
| 276 |
&gpio3 { |
| 277 |
status = "okay"; |
| 278 |
}; |
| 279 |
|
| 280 |
&gpio4 { |
| 281 |
status = "okay"; |
| 282 |
}; |
| 283 |
|
| 284 |
&gpio5 { |
| 285 |
status = "okay"; |
| 286 |
}; |
| 287 |
|
| 288 |
&mmc2 { |
| 289 |
status = "okay"; |
| 290 |
pinctrl-names = "default"; |
| 291 |
pinctrl-0 = <&emmc_pins>; |
| 292 |
vmmc-supply = <&vmmc_3v3>; |
| 293 |
bus-width = <8>; |
| 294 |
non-removable; |
| 295 |
}; |
| 296 |
|
| 297 |
&spi0 { |
| 298 |
status = "okay"; |
| 299 |
pinctrl-names = "default"; |
| 300 |
pinctrl-0 = <&spi0_pins>; |
| 301 |
dmas = <&edma 16 0 |
| 302 |
&edma 17 0>; |
| 303 |
dma-names = "tx0", "rx0"; |
| 304 |
|
| 305 |
flash: flash@0 { |
| 306 |
#address-cells = <1>; |
| 307 |
#size-cells = <1>; |
| 308 |
compatible = "jedec,spi-nor"; |
| 309 |
reg = <0>; |
| 310 |
spi-max-frequency = <20000000>; |
| 311 |
partition@0 { |
| 312 |
label = "uboot"; |
| 313 |
reg = <0x0 0xc0000>; |
| 314 |
}; |
| 315 |
|
| 316 |
partition@c0000 { |
| 317 |
label = "uboot environment"; |
| 318 |
reg = <0xc0000 0x40000>; |
| 319 |
}; |
| 320 |
|
| 321 |
partition@100000 { |
| 322 |
label = "reserved"; |
| 323 |
reg = <0x100000 0x100000>; |
| 324 |
}; |
| 325 |
}; |
| 326 |
}; |
| 327 |
|
| 328 |
&mac_sw { |
| 329 |
pinctrl-names = "default"; |
| 330 |
pinctrl-0 = <&cpsw_default>; |
| 331 |
status = "okay"; |
| 332 |
}; |
| 333 |
|
| 334 |
&davinci_mdio_sw { |
| 335 |
pinctrl-names = "default"; |
| 336 |
pinctrl-0 = <&davinci_mdio_default>; |
| 337 |
|
| 338 |
ethphy0: ethernet-phy@0 { |
| 339 |
reg = <0>; |
| 340 |
}; |
| 341 |
|
| 342 |
ethphy1: ethernet-phy@1 { |
| 343 |
reg = <1>; |
| 344 |
}; |
| 345 |
}; |
| 346 |
|
| 347 |
&cpsw_port1 { |
| 348 |
phy-handle = <ðphy0>; |
| 349 |
phy-mode = "rgmii-txid"; |
| 350 |
ti,dual-emac-pvid = <1>; |
| 351 |
}; |
| 352 |
|
| 353 |
&cpsw_port2 { |
| 354 |
phy-handle = <ðphy1>; |
| 355 |
phy-mode = "rgmii-txid"; |
| 356 |
ti,dual-emac-pvid = <2>; |
| 357 |
}; |
| 358 |
|
| 359 |
&dwc3_1 { |
| 360 |
status = "okay"; |
| 361 |
}; |
| 362 |
|
| 363 |
&usb2_phy1 { |
| 364 |
status = "okay"; |
| 365 |
}; |
| 366 |
|
| 367 |
&usb1 { |
| 368 |
dr_mode = "host"; |
| 369 |
status = "okay"; |
| 370 |
}; |
| 371 |
|
| 372 |
&dwc3_2 { |
| 373 |
status = "okay"; |
| 374 |
}; |
| 375 |
|
| 376 |
&usb2_phy2 { |
| 377 |
status = "okay"; |
| 378 |
}; |
| 379 |
|
| 380 |
&usb2 { |
| 381 |
dr_mode = "host"; |
| 382 |
status = "okay"; |
| 383 |
interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>, |
| 384 |
<GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>, |
| 385 |
<GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; |
| 386 |
interrupt-names = "peripheral", "host", "otg"; |
| 387 |
}; |
| 388 |
|
| 389 |
&elm { |
| 390 |
status = "okay"; |
| 391 |
}; |
| 392 |
|
| 393 |
&uart0 { |
| 394 |
status = "okay"; |
| 395 |
}; |
| 396 |
|
| 397 |
&tscadc { |
| 398 |
status = "okay"; |
| 399 |
tsc { |
| 400 |
ti,wires = <4>; |
| 401 |
ti,x-plate-resistance = <200>; |
| 402 |
ti,coordinate-readouts = <5>; |
| 403 |
ti,wire-config = <0x00 0x11 0x22 0x33>; |
| 404 |
}; |
| 405 |
|
| 406 |
adc { |
| 407 |
ti,adc-channels = <4 5 6 7>; |
| 408 |
}; |
| 409 |
}; |
| 410 |
|
| 411 |
&cpu { |
| 412 |
cpu0-supply = <&dcdc2>; |
| 413 |
operating-points = <1000000 1330000>, |
| 414 |
<800000 1260000>, |
| 415 |
<720000 1200000>, |
| 416 |
<600000 1100000>, |
| 417 |
<300000 950000>; |
| 418 |
}; |
| 419 |
|
| 420 |
&pruss1_mdio { |
| 421 |
status = "disabled"; |
| 422 |
}; |