| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Copyright (C) 2014 Thomas Petazzoni <[email protected]> |
| 4 |
* Copyright (C) Sylver Bruneau <[email protected]> |
| 5 |
*/ |
| 6 |
|
| 7 |
/dts-v1/; |
| 8 |
|
| 9 |
#include <dt-bindings/gpio/gpio.h> |
| 10 |
#include <dt-bindings/input/input.h> |
| 11 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 12 |
#include "orion5x-mv88f5182.dtsi" |
| 13 |
|
| 14 |
/ { |
| 15 |
model = "Maxtor Shared Storage II"; |
| 16 |
compatible = "maxtor,shared-storage-2", "marvell,orion5x-88f5182", "marvell,orion5x"; |
| 17 |
|
| 18 |
memory { |
| 19 |
device_type = "memory"; |
| 20 |
reg = <0x00000000 0x4000000>; /* 64 MB */ |
| 21 |
}; |
| 22 |
|
| 23 |
chosen { |
| 24 |
bootargs = "console=ttyS0,115200n8 earlyprintk"; |
| 25 |
stdout-path = &uart0; |
| 26 |
}; |
| 27 |
|
| 28 |
soc { |
| 29 |
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>, |
| 30 |
<MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>, |
| 31 |
<MBUS_ID(0x01, 0x0f) 0 0xff800000 0x40000>; |
| 32 |
}; |
| 33 |
|
| 34 |
gpio-keys { |
| 35 |
compatible = "gpio-keys"; |
| 36 |
pinctrl-0 = <&pmx_buttons>; |
| 37 |
pinctrl-names = "default"; |
| 38 |
|
| 39 |
key-power { |
| 40 |
label = "Power"; |
| 41 |
linux,code = <KEY_POWER>; |
| 42 |
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; |
| 43 |
}; |
| 44 |
|
| 45 |
key-reset { |
| 46 |
label = "Reset"; |
| 47 |
linux,code = <KEY_RESTART>; |
| 48 |
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; |
| 49 |
}; |
| 50 |
}; |
| 51 |
}; |
| 52 |
|
| 53 |
&devbus_bootcs { |
| 54 |
status = "okay"; |
| 55 |
|
| 56 |
devbus,keep-config; |
| 57 |
|
| 58 |
/* |
| 59 |
* Currently the MTD code does not recognize the MX29LV400CBCT |
| 60 |
* as a bottom-type device. This could cause risks of |
| 61 |
* accidentally erasing critical flash sectors. We thus define |
| 62 |
* a single, write-protected partition covering the whole |
| 63 |
* flash. TODO: once the flash part TOP/BOTTOM detection |
| 64 |
* issue is sorted out in the MTD code, break this into at |
| 65 |
* least three partitions: 'u-boot code', 'u-boot environment' |
| 66 |
* and 'whatever is left'. |
| 67 |
*/ |
| 68 |
flash@0 { |
| 69 |
compatible = "cfi-flash"; |
| 70 |
reg = <0 0x40000>; |
| 71 |
bank-width = <1>; |
| 72 |
#address-cells = <1>; |
| 73 |
#size-cells = <1>; |
| 74 |
}; |
| 75 |
}; |
| 76 |
|
| 77 |
&mdio { |
| 78 |
status = "okay"; |
| 79 |
|
| 80 |
ethphy: ethernet-phy { |
| 81 |
reg = <8>; |
| 82 |
}; |
| 83 |
}; |
| 84 |
|
| 85 |
&ehci0 { |
| 86 |
status = "okay"; |
| 87 |
}; |
| 88 |
|
| 89 |
ð { |
| 90 |
status = "okay"; |
| 91 |
|
| 92 |
ethernet-port@0 { |
| 93 |
phy-handle = <ðphy>; |
| 94 |
}; |
| 95 |
}; |
| 96 |
|
| 97 |
&i2c { |
| 98 |
status = "okay"; |
| 99 |
clock-frequency = <100000>; |
| 100 |
#address-cells = <1>; |
| 101 |
|
| 102 |
rtc@68 { |
| 103 |
compatible = "st,m41t81"; |
| 104 |
reg = <0x68>; |
| 105 |
pinctrl-0 = <&pmx_rtc>; |
| 106 |
pinctrl-names = "default"; |
| 107 |
interrupt-parent = <&gpio0>; |
| 108 |
interrupts = <3 IRQ_TYPE_LEVEL_LOW>; |
| 109 |
}; |
| 110 |
}; |
| 111 |
|
| 112 |
&pinctrl { |
| 113 |
pinctrl-0 = <&pmx_leds &pmx_misc>; |
| 114 |
pinctrl-names = "default"; |
| 115 |
|
| 116 |
pmx_buttons: pmx-buttons { |
| 117 |
marvell,pins = "mpp11", "mpp12"; |
| 118 |
marvell,function = "gpio"; |
| 119 |
}; |
| 120 |
|
| 121 |
/* |
| 122 |
* MPP0: Power LED |
| 123 |
* MPP1: Error LED |
| 124 |
*/ |
| 125 |
pmx_leds: pmx-leds { |
| 126 |
marvell,pins = "mpp0", "mpp1"; |
| 127 |
marvell,function = "gpio"; |
| 128 |
}; |
| 129 |
|
| 130 |
/* |
| 131 |
* MPP4: HDD ind. (Single/Dual) |
| 132 |
* MPP5: HD0 5V control |
| 133 |
* MPP6: HD0 12V control |
| 134 |
* MPP7: HD1 5V control |
| 135 |
* MPP8: HD1 12V control |
| 136 |
*/ |
| 137 |
pmx_misc: pmx-misc { |
| 138 |
marvell,pins = "mpp4", "mpp5", "mpp6", "mpp7", "mpp8", "mpp10"; |
| 139 |
marvell,function = "gpio"; |
| 140 |
}; |
| 141 |
|
| 142 |
pmx_rtc: pmx-rtc { |
| 143 |
marvell,pins = "mpp3"; |
| 144 |
marvell,function = "gpio"; |
| 145 |
}; |
| 146 |
|
| 147 |
pmx_sata0_led_active: pmx-sata0-led-active { |
| 148 |
marvell,pins = "mpp14"; |
| 149 |
marvell,function = "sata0"; |
| 150 |
}; |
| 151 |
|
| 152 |
pmx_sata1_led_active: pmx-sata1-led-active { |
| 153 |
marvell,pins = "mpp15"; |
| 154 |
marvell,function = "sata1"; |
| 155 |
}; |
| 156 |
|
| 157 |
/* |
| 158 |
* Non MPP GPIOs: |
| 159 |
* GPIO 22: USB port 1 fuse (0 = Fail, 1 = Ok) |
| 160 |
* GPIO 23: Blue front LED off |
| 161 |
* GPIO 24: Inhibit board power off (0 = Disabled, 1 = Enabled) |
| 162 |
*/ |
| 163 |
}; |
| 164 |
|
| 165 |
&sata { |
| 166 |
pinctrl-0 = <&pmx_sata0_led_active |
| 167 |
&pmx_sata1_led_active>; |
| 168 |
pinctrl-names = "default"; |
| 169 |
status = "okay"; |
| 170 |
nr-ports = <2>; |
| 171 |
}; |
| 172 |
|
| 173 |
&uart0 { |
| 174 |
status = "okay"; |
| 175 |
}; |