| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Device Tree file for Synology DS213j |
| 4 |
* |
| 5 |
* Copyright (C) 2014, Arnaud EBALARD <[email protected]> |
| 6 |
* |
| 7 |
* Note: this Device Tree assumes that the bootloader has remapped the |
| 8 |
* internal registers to 0xf1000000 (instead of the old 0xd0000000). |
| 9 |
* The 0xf1000000 is the default used by the recent, DT-capable, U-Boot |
| 10 |
* bootloaders provided by Marvell. It is used in recent versions of |
| 11 |
* DSM software provided by Synology. Nonetheless, some earlier boards |
| 12 |
* were delivered with an older version of u-boot that left internal |
| 13 |
* registers mapped at 0xd0000000. If you have such a device you will |
| 14 |
* not be able to directly boot a kernel based on this Device Tree. In |
| 15 |
* that case, the preferred solution is to update your bootloader (e.g. |
| 16 |
* by upgrading to latest version of DSM, or building a new one and |
| 17 |
* installing it from u-boot prompt) or adjust the Devive Tree |
| 18 |
* (s/0xf1000000/0xd0000000/ in 'ranges' below). |
| 19 |
*/ |
| 20 |
|
| 21 |
/dts-v1/; |
| 22 |
|
| 23 |
#include <dt-bindings/input/input.h> |
| 24 |
#include <dt-bindings/gpio/gpio.h> |
| 25 |
#include "armada-370.dtsi" |
| 26 |
|
| 27 |
/ { |
| 28 |
model = "Synology DS213j"; |
| 29 |
compatible = "synology,ds213j", "marvell,armada370", |
| 30 |
"marvell,armada-370-xp"; |
| 31 |
|
| 32 |
chosen { |
| 33 |
stdout-path = "serial0:115200n8"; |
| 34 |
}; |
| 35 |
|
| 36 |
memory@0 { |
| 37 |
device_type = "memory"; |
| 38 |
reg = <0x00000000 0x20000000>; /* 512 MB */ |
| 39 |
}; |
| 40 |
|
| 41 |
soc { |
| 42 |
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 |
| 43 |
MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000 |
| 44 |
MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>; |
| 45 |
|
| 46 |
internal-regs { |
| 47 |
|
| 48 |
/* RTC provided by Seiko S-35390A I2C RTC chip below */ |
| 49 |
rtc@10300 { |
| 50 |
status = "disabled"; |
| 51 |
}; |
| 52 |
|
| 53 |
i2c@11000 { |
| 54 |
compatible = "marvell,mv64xxx-i2c"; |
| 55 |
pinctrl-0 = <&i2c0_pins>; |
| 56 |
pinctrl-names = "default"; |
| 57 |
clock-frequency = <400000>; |
| 58 |
status = "okay"; |
| 59 |
|
| 60 |
/* Main device RTC chip */ |
| 61 |
s35390a: s35390a@30 { |
| 62 |
compatible = "sii,s35390a"; |
| 63 |
reg = <0x30>; |
| 64 |
}; |
| 65 |
}; |
| 66 |
|
| 67 |
/* Connected to a header on device's PCB */ |
| 68 |
serial@12000 { |
| 69 |
status = "okay"; |
| 70 |
}; |
| 71 |
|
| 72 |
/* Connected to a TI MSP430F2111 for power control */ |
| 73 |
serial@12100 { |
| 74 |
status = "okay"; |
| 75 |
}; |
| 76 |
|
| 77 |
poweroff@12100 { |
| 78 |
compatible = "synology,power-off"; |
| 79 |
reg = <0x12100 0x100>; |
| 80 |
clocks = <&coreclk 0>; |
| 81 |
}; |
| 82 |
|
| 83 |
/* rear USB port, near reset button */ |
| 84 |
usb@50000 { |
| 85 |
status = "okay"; |
| 86 |
}; |
| 87 |
|
| 88 |
/* rear USB port, near RJ45 port */ |
| 89 |
usb@51000 { |
| 90 |
status = "okay"; |
| 91 |
}; |
| 92 |
|
| 93 |
ethernet@70000 { |
| 94 |
status = "okay"; |
| 95 |
phy = <&phy1>; |
| 96 |
phy-mode = "sgmii"; |
| 97 |
}; |
| 98 |
|
| 99 |
sata@a0000 { |
| 100 |
nr-ports = <2>; |
| 101 |
status = "okay"; |
| 102 |
}; |
| 103 |
}; |
| 104 |
}; |
| 105 |
|
| 106 |
gpio-fan-32-38 { |
| 107 |
status = "okay"; |
| 108 |
compatible = "gpio-fan"; |
| 109 |
pinctrl-0 = <&fan_ctrl_low_pin &fan_ctrl_mid_pin |
| 110 |
&fan_ctrl_high_pin &fan_alarm_pin>; |
| 111 |
pinctrl-names = "default"; |
| 112 |
gpios = <&gpio1 31 GPIO_ACTIVE_HIGH |
| 113 |
&gpio2 0 GPIO_ACTIVE_HIGH |
| 114 |
&gpio2 1 GPIO_ACTIVE_HIGH>; |
| 115 |
alarm-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; |
| 116 |
gpio-fan,speed-map = < 0 0>, |
| 117 |
<1000 1>, |
| 118 |
<1150 2>, |
| 119 |
<1350 4>, |
| 120 |
<1500 3>, |
| 121 |
<1650 5>, |
| 122 |
<1750 6>, |
| 123 |
<1900 7>; |
| 124 |
}; |
| 125 |
|
| 126 |
gpio-leds { |
| 127 |
compatible = "gpio-leds"; |
| 128 |
pinctrl-0 = <&disk1_led_pin |
| 129 |
&disk2_led_pin>; |
| 130 |
pinctrl-names = "default"; |
| 131 |
|
| 132 |
disk1-led-amber { |
| 133 |
label = "synology:amber:disk1"; |
| 134 |
gpios = <&gpio0 31 GPIO_ACTIVE_LOW>; |
| 135 |
default-state = "keep"; |
| 136 |
}; |
| 137 |
|
| 138 |
disk2-led-amber { |
| 139 |
label = "synology:amber:disk2"; |
| 140 |
gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; |
| 141 |
default-state = "keep"; |
| 142 |
}; |
| 143 |
}; |
| 144 |
|
| 145 |
sata1_regulator: sata1-regulator-1 { |
| 146 |
compatible = "regulator-fixed"; |
| 147 |
regulator-name = "SATA1 Power"; |
| 148 |
regulator-min-microvolt = <5000000>; |
| 149 |
regulator-max-microvolt = <5000000>; |
| 150 |
startup-delay-us = <2000000>; |
| 151 |
enable-active-high; |
| 152 |
regulator-always-on; |
| 153 |
regulator-boot-on; |
| 154 |
gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; |
| 155 |
pinctrl-0 = <&sata1_pwr_pin>; |
| 156 |
pinctrl-names = "default"; |
| 157 |
}; |
| 158 |
|
| 159 |
sata2_regulator: sata2-regulator-2 { |
| 160 |
compatible = "regulator-fixed"; |
| 161 |
regulator-name = "SATA2 Power"; |
| 162 |
regulator-min-microvolt = <5000000>; |
| 163 |
regulator-max-microvolt = <5000000>; |
| 164 |
startup-delay-us = <4000000>; |
| 165 |
enable-active-high; |
| 166 |
regulator-always-on; |
| 167 |
regulator-boot-on; |
| 168 |
gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>; |
| 169 |
pinctrl-0 = <&sata2_pwr_pin>; |
| 170 |
pinctrl-names = "default"; |
| 171 |
}; |
| 172 |
}; |
| 173 |
|
| 174 |
&mdio { |
| 175 |
phy1: ethernet-phy@1 { /* Marvell 88E1512 */ |
| 176 |
reg = <1>; |
| 177 |
}; |
| 178 |
}; |
| 179 |
|
| 180 |
&pinctrl { |
| 181 |
disk1_led_pin: disk1-led-pin { |
| 182 |
marvell,pins = "mpp31"; |
| 183 |
marvell,function = "gpio"; |
| 184 |
}; |
| 185 |
|
| 186 |
disk2_led_pin: disk2-led-pin { |
| 187 |
marvell,pins = "mpp32"; |
| 188 |
marvell,function = "gpio"; |
| 189 |
}; |
| 190 |
|
| 191 |
sata1_pwr_pin: sata1-pwr-pin { |
| 192 |
marvell,pins = "mpp37"; |
| 193 |
marvell,function = "gpio"; |
| 194 |
}; |
| 195 |
|
| 196 |
sata2_pwr_pin: sata2-pwr-pin { |
| 197 |
marvell,pins = "mpp62"; |
| 198 |
marvell,function = "gpio"; |
| 199 |
}; |
| 200 |
|
| 201 |
sata1_pres_pin: sata1-pres-pin { |
| 202 |
marvell,pins = "mpp60"; |
| 203 |
marvell,function = "gpio"; |
| 204 |
}; |
| 205 |
|
| 206 |
sata2_pres_pin: sata2-pres-pin { |
| 207 |
marvell,pins = "mpp48"; |
| 208 |
marvell,function = "gpio"; |
| 209 |
}; |
| 210 |
|
| 211 |
syno_id_bit0_pin: syno-id-bit0-pin { |
| 212 |
marvell,pins = "mpp55"; |
| 213 |
marvell,function = "gpio"; |
| 214 |
}; |
| 215 |
|
| 216 |
syno_id_bit1_pin: syno-id-bit1-pin { |
| 217 |
marvell,pins = "mpp56"; |
| 218 |
marvell,function = "gpio"; |
| 219 |
}; |
| 220 |
|
| 221 |
syno_id_bit2_pin: syno-id-bit2-pin { |
| 222 |
marvell,pins = "mpp57"; |
| 223 |
marvell,function = "gpio"; |
| 224 |
}; |
| 225 |
|
| 226 |
syno_id_bit3_pin: syno-id-bit3-pin { |
| 227 |
marvell,pins = "mpp58"; |
| 228 |
marvell,function = "gpio"; |
| 229 |
}; |
| 230 |
|
| 231 |
fan_ctrl_low_pin: fan-ctrl-low-pin { |
| 232 |
marvell,pins = "mpp65"; |
| 233 |
marvell,function = "gpio"; |
| 234 |
}; |
| 235 |
|
| 236 |
fan_ctrl_mid_pin: fan-ctrl-mid-pin { |
| 237 |
marvell,pins = "mpp64"; |
| 238 |
marvell,function = "gpio"; |
| 239 |
}; |
| 240 |
|
| 241 |
fan_ctrl_high_pin: fan-ctrl-high-pin { |
| 242 |
marvell,pins = "mpp63"; |
| 243 |
marvell,function = "gpio"; |
| 244 |
}; |
| 245 |
|
| 246 |
fan_alarm_pin: fan-alarm-pin { |
| 247 |
marvell,pins = "mpp38"; |
| 248 |
marvell,function = "gpio"; |
| 249 |
}; |
| 250 |
}; |
| 251 |
|
| 252 |
&spi0 { |
| 253 |
status = "okay"; |
| 254 |
|
| 255 |
flash@0 { |
| 256 |
#address-cells = <1>; |
| 257 |
#size-cells = <1>; |
| 258 |
compatible = "micron,n25q064", "jedec,spi-nor"; |
| 259 |
reg = <0>; /* Chip select 0 */ |
| 260 |
spi-max-frequency = <20000000>; |
| 261 |
|
| 262 |
/* |
| 263 |
* Warning! |
| 264 |
* |
| 265 |
* Synology u-boot uses its compiled-in environment |
| 266 |
* and it seems Synology did not care to change u-boot |
| 267 |
* default configuration in order to allow saving a |
| 268 |
* modified environment at a sensible location. So, |
| 269 |
* if you do a 'saveenv' under u-boot, your modified |
| 270 |
* environment will be saved at 1MB after the start |
| 271 |
* of the flash, i.e. in the middle of the uImage. |
| 272 |
* For that reason, it is strongly advised not to |
| 273 |
* change the default environment, unless you know |
| 274 |
* what you are doing. |
| 275 |
*/ |
| 276 |
partition@0 { /* u-boot */ |
| 277 |
label = "RedBoot"; |
| 278 |
reg = <0x00000000 0x000c0000>; /* 768KB */ |
| 279 |
}; |
| 280 |
|
| 281 |
partition@c0000 { /* uImage */ |
| 282 |
label = "zImage"; |
| 283 |
reg = <0x000c0000 0x002d0000>; /* 2880KB */ |
| 284 |
}; |
| 285 |
|
| 286 |
partition@390000 { /* uInitramfs */ |
| 287 |
label = "rd.gz"; |
| 288 |
reg = <0x00390000 0x00440000>; /* 4250KB */ |
| 289 |
}; |
| 290 |
|
| 291 |
partition@7d0000 { /* MAC address and serial number */ |
| 292 |
label = "vendor"; |
| 293 |
reg = <0x007d0000 0x00010000>; /* 64KB */ |
| 294 |
}; |
| 295 |
|
| 296 |
partition@7e0000 { |
| 297 |
label = "RedBoot config"; |
| 298 |
reg = <0x007e0000 0x00010000>; /* 64KB */ |
| 299 |
}; |
| 300 |
|
| 301 |
partition@7f0000 { |
| 302 |
label = "FIS directory"; |
| 303 |
reg = <0x007f0000 0x00010000>; /* 64KB */ |
| 304 |
}; |
| 305 |
}; |
| 306 |
}; |