| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT |
| 2 |
/* |
| 3 |
* Dell Wyse 3020 a.k.a. "Ariel" a.k.a. Tx0D (T00D, T10D) |
| 4 |
* |
| 5 |
* Copyright (C) 2019 Lubomir Rintel <[email protected]> |
| 6 |
*/ |
| 7 |
|
| 8 |
/dts-v1/; |
| 9 |
#include "mmp3.dtsi" |
| 10 |
#include <dt-bindings/gpio/gpio.h> |
| 11 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 12 |
|
| 13 |
/ { |
| 14 |
model = "Dell Ariel"; |
| 15 |
compatible = "dell,wyse-ariel", "marvell,mmp3"; |
| 16 |
|
| 17 |
aliases { |
| 18 |
serial2 = &uart3; |
| 19 |
}; |
| 20 |
|
| 21 |
chosen { |
| 22 |
#address-cells = <0x1>; |
| 23 |
#size-cells = <0x1>; |
| 24 |
ranges; |
| 25 |
bootargs = "earlyprintk=ttyS2,115200 console=ttyS2,115200"; |
| 26 |
}; |
| 27 |
|
| 28 |
memory@0 { |
| 29 |
available = <0x7f700000 0x7ff00000 0x00000000 0x7f600000>; |
| 30 |
reg = <0x0 0x80000000>; |
| 31 |
device_type = "memory"; |
| 32 |
}; |
| 33 |
|
| 34 |
ec_input_spi: spi { |
| 35 |
compatible = "spi-gpio"; |
| 36 |
#address-cells = <1>; |
| 37 |
#size-cells = <0>; |
| 38 |
|
| 39 |
num-chipselects = <0>; |
| 40 |
sck-gpios = <&gpio 55 GPIO_ACTIVE_HIGH>; |
| 41 |
miso-gpios = <&gpio 57 GPIO_ACTIVE_HIGH>; |
| 42 |
mosi-gpios = <&gpio 58 GPIO_ACTIVE_HIGH>; |
| 43 |
}; |
| 44 |
}; |
| 45 |
|
| 46 |
&uart3 { |
| 47 |
status = "okay"; |
| 48 |
}; |
| 49 |
|
| 50 |
&rtc { |
| 51 |
status = "okay"; |
| 52 |
}; |
| 53 |
|
| 54 |
&usb_otg0 { |
| 55 |
status = "okay"; |
| 56 |
}; |
| 57 |
|
| 58 |
&usb_otg_phy0 { |
| 59 |
status = "okay"; |
| 60 |
}; |
| 61 |
|
| 62 |
&hsic0 { |
| 63 |
status = "okay"; |
| 64 |
|
| 65 |
usb1@1 { |
| 66 |
compatible = "usb424,2640"; |
| 67 |
reg = <0x01>; |
| 68 |
#address-cells = <0x01>; |
| 69 |
#size-cells = <0x00>; |
| 70 |
|
| 71 |
mass-storage@1 { |
| 72 |
compatible = "usb424,4040"; |
| 73 |
reg = <0x01>; |
| 74 |
status = "disabled"; |
| 75 |
}; |
| 76 |
}; |
| 77 |
}; |
| 78 |
|
| 79 |
&hsic_phy0 { |
| 80 |
status = "okay"; |
| 81 |
reset-gpios = <&gpio 63 GPIO_ACTIVE_HIGH>; |
| 82 |
}; |
| 83 |
|
| 84 |
&mmc3 { |
| 85 |
status = "okay"; |
| 86 |
max-frequency = <50000000>; |
| 87 |
status = "okay"; |
| 88 |
bus-width = <8>; |
| 89 |
non-removable; |
| 90 |
cap-mmc-highspeed; |
| 91 |
}; |
| 92 |
|
| 93 |
&twsi1 { |
| 94 |
status = "okay"; |
| 95 |
|
| 96 |
rtc@68 { |
| 97 |
compatible = "dallas,ds1338"; |
| 98 |
reg = <0x68>; |
| 99 |
status = "okay"; |
| 100 |
}; |
| 101 |
}; |
| 102 |
|
| 103 |
&twsi3 { |
| 104 |
status = "okay"; |
| 105 |
}; |
| 106 |
|
| 107 |
&twsi4 { |
| 108 |
status = "okay"; |
| 109 |
|
| 110 |
embedded-controller@58 { |
| 111 |
compatible = "dell,wyse-ariel-ec", "ene,kb3930"; |
| 112 |
reg = <0x58>; |
| 113 |
system-power-controller; |
| 114 |
|
| 115 |
off-gpios = <&gpio 126 GPIO_ACTIVE_HIGH>, |
| 116 |
<&gpio 127 GPIO_ACTIVE_HIGH>; |
| 117 |
}; |
| 118 |
}; |
| 119 |
|
| 120 |
&ssp1 { |
| 121 |
status = "okay"; |
| 122 |
cs-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; |
| 123 |
|
| 124 |
firmware-flash@0 { |
| 125 |
compatible = "winbond,w25q32", "jedec,spi-nor"; |
| 126 |
reg = <0>; |
| 127 |
spi-max-frequency = <104000000>; |
| 128 |
m25p,fast-read; |
| 129 |
}; |
| 130 |
}; |
| 131 |
|
| 132 |
&ec_input_spi { |
| 133 |
status = "okay"; |
| 134 |
cs-gpios = <&gpio 56 GPIO_ACTIVE_LOW>; |
| 135 |
|
| 136 |
power-button@0 { |
| 137 |
reg = <0>; |
| 138 |
interrupt-parent = <&gpio>; |
| 139 |
interrupts = <60 IRQ_TYPE_EDGE_RISING>; |
| 140 |
compatible = "dell,wyse-ariel-ec-input", "ene,kb3930-input"; |
| 141 |
spi-max-frequency = <33000000>; |
| 142 |
}; |
| 143 |
}; |
| 144 |
|
| 145 |
&gpu_2d { |
| 146 |
status = "okay"; |
| 147 |
}; |
| 148 |
|
| 149 |
&gpu_3d { |
| 150 |
status = "okay"; |
| 151 |
}; |