| 1 |
// SPDX-License-Identifier: (GPL-2.0 OR MIT) |
| 2 |
/* |
| 3 |
* Device Tree file for the Linksys WRT1900AC (Mamba). |
| 4 |
* |
| 5 |
* Note: this board is shipped with a new generation boot loader that |
| 6 |
* remaps internal registers at 0xf1000000. Therefore, if earlyprintk |
| 7 |
* is used, the CONFIG_DEBUG_MVEBU_UART0_ALTERNATE option should be |
| 8 |
* used. |
| 9 |
* |
| 10 |
* Copyright (C) 2014 Imre Kaloz <[email protected]> |
| 11 |
* |
| 12 |
* Based on armada-xp-axpwifiap.dts: |
| 13 |
* |
| 14 |
* Copyright (C) 2013 Marvell |
| 15 |
* |
| 16 |
* Thomas Petazzoni <[email protected]> |
| 17 |
*/ |
| 18 |
|
| 19 |
/dts-v1/; |
| 20 |
#include <dt-bindings/gpio/gpio.h> |
| 21 |
#include <dt-bindings/input/input.h> |
| 22 |
#include "armada-xp-mv78230.dtsi" |
| 23 |
|
| 24 |
/ { |
| 25 |
model = "Linksys WRT1900AC"; |
| 26 |
compatible = "linksys,mamba", "marvell,armadaxp-mv78230", |
| 27 |
"marvell,armadaxp", "marvell,armada-370-xp"; |
| 28 |
|
| 29 |
chosen { |
| 30 |
bootargs = "console=ttyS0,115200"; |
| 31 |
stdout-path = &uart0; |
| 32 |
}; |
| 33 |
|
| 34 |
memory@0 { |
| 35 |
device_type = "memory"; |
| 36 |
reg = <0x00000000 0x00000000 0x00000000 0x10000000>; /* 256MB */ |
| 37 |
}; |
| 38 |
|
| 39 |
soc { |
| 40 |
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 |
| 41 |
MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 |
| 42 |
MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000 |
| 43 |
MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000 |
| 44 |
MBUS_ID(0x0c, 0x04) 0 0 0xf1200000 0x100000>; |
| 45 |
|
| 46 |
internal-regs { |
| 47 |
|
| 48 |
rtc@10300 { |
| 49 |
/* No crystal connected to the internal RTC */ |
| 50 |
status = "disabled"; |
| 51 |
}; |
| 52 |
|
| 53 |
/* J10: VCC, NC, RX, NC, TX, GND */ |
| 54 |
serial@12000 { |
| 55 |
status = "okay"; |
| 56 |
}; |
| 57 |
|
| 58 |
sata@a0000 { |
| 59 |
nr-ports = <1>; |
| 60 |
status = "okay"; |
| 61 |
}; |
| 62 |
|
| 63 |
ethernet@70000 { |
| 64 |
pinctrl-0 = <&ge0_rgmii_pins>; |
| 65 |
pinctrl-names = "default"; |
| 66 |
status = "okay"; |
| 67 |
phy-mode = "rgmii-id"; |
| 68 |
buffer-manager = <&bm>; |
| 69 |
bm,pool-long = <0>; |
| 70 |
bm,pool-short = <1>; |
| 71 |
fixed-link { |
| 72 |
speed = <1000>; |
| 73 |
full-duplex; |
| 74 |
}; |
| 75 |
}; |
| 76 |
|
| 77 |
ethernet@74000 { |
| 78 |
pinctrl-0 = <&ge1_rgmii_pins>; |
| 79 |
pinctrl-names = "default"; |
| 80 |
status = "okay"; |
| 81 |
phy-mode = "rgmii-id"; |
| 82 |
buffer-manager = <&bm>; |
| 83 |
bm,pool-long = <2>; |
| 84 |
bm,pool-short = <3>; |
| 85 |
fixed-link { |
| 86 |
speed = <1000>; |
| 87 |
full-duplex; |
| 88 |
}; |
| 89 |
}; |
| 90 |
|
| 91 |
/* USB part of the eSATA/USB 2.0 port */ |
| 92 |
usb@50000 { |
| 93 |
status = "okay"; |
| 94 |
}; |
| 95 |
|
| 96 |
i2c@11000 { |
| 97 |
status = "okay"; |
| 98 |
clock-frequency = <100000>; |
| 99 |
|
| 100 |
tmp421@4c { |
| 101 |
compatible = "ti,tmp421"; |
| 102 |
reg = <0x4c>; |
| 103 |
}; |
| 104 |
|
| 105 |
tlc59116@68 { |
| 106 |
#address-cells = <1>; |
| 107 |
#size-cells = <0>; |
| 108 |
#gpio-cells = <2>; |
| 109 |
compatible = "ti,tlc59116"; |
| 110 |
reg = <0x68>; |
| 111 |
|
| 112 |
wan_amber@0 { |
| 113 |
label = "mamba:amber:wan"; |
| 114 |
reg = <0x0>; |
| 115 |
}; |
| 116 |
|
| 117 |
wan_white@1 { |
| 118 |
label = "mamba:white:wan"; |
| 119 |
reg = <0x1>; |
| 120 |
}; |
| 121 |
|
| 122 |
wlan_2g@2 { |
| 123 |
label = "mamba:white:wlan_2g"; |
| 124 |
reg = <0x2>; |
| 125 |
}; |
| 126 |
|
| 127 |
wlan_5g@3 { |
| 128 |
label = "mamba:white:wlan_5g"; |
| 129 |
reg = <0x3>; |
| 130 |
}; |
| 131 |
|
| 132 |
esata@4 { |
| 133 |
label = "mamba:white:esata"; |
| 134 |
reg = <0x4>; |
| 135 |
linux,default-trigger = "disk-activity"; |
| 136 |
}; |
| 137 |
|
| 138 |
usb2@5 { |
| 139 |
label = "mamba:white:usb2"; |
| 140 |
reg = <0x5>; |
| 141 |
}; |
| 142 |
|
| 143 |
usb3_1@6 { |
| 144 |
label = "mamba:white:usb3_1"; |
| 145 |
reg = <0x6>; |
| 146 |
}; |
| 147 |
|
| 148 |
usb3_2@7 { |
| 149 |
label = "mamba:white:usb3_2"; |
| 150 |
reg = <0x7>; |
| 151 |
}; |
| 152 |
|
| 153 |
wps_white@8 { |
| 154 |
label = "mamba:white:wps"; |
| 155 |
reg = <0x8>; |
| 156 |
}; |
| 157 |
|
| 158 |
wps_amber@9 { |
| 159 |
label = "mamba:amber:wps"; |
| 160 |
reg = <0x9>; |
| 161 |
}; |
| 162 |
}; |
| 163 |
}; |
| 164 |
|
| 165 |
bm@c8000 { |
| 166 |
status = "okay"; |
| 167 |
}; |
| 168 |
}; |
| 169 |
|
| 170 |
bm-bppi { |
| 171 |
status = "okay"; |
| 172 |
}; |
| 173 |
}; |
| 174 |
|
| 175 |
gpio-keys { |
| 176 |
compatible = "gpio-keys"; |
| 177 |
pinctrl-0 = <&keys_pin>; |
| 178 |
pinctrl-names = "default"; |
| 179 |
|
| 180 |
button-wps { |
| 181 |
label = "WPS"; |
| 182 |
linux,code = <KEY_WPS_BUTTON>; |
| 183 |
gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; |
| 184 |
}; |
| 185 |
|
| 186 |
button-reset { |
| 187 |
label = "Factory Reset Button"; |
| 188 |
linux,code = <KEY_RESTART>; |
| 189 |
gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; |
| 190 |
}; |
| 191 |
}; |
| 192 |
|
| 193 |
gpio-leds { |
| 194 |
compatible = "gpio-leds"; |
| 195 |
pinctrl-0 = <&power_led_pin>; |
| 196 |
pinctrl-names = "default"; |
| 197 |
|
| 198 |
led-power { |
| 199 |
label = "mamba:white:power"; |
| 200 |
gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; |
| 201 |
default-state = "on"; |
| 202 |
}; |
| 203 |
}; |
| 204 |
|
| 205 |
pwm_fan { |
| 206 |
/* SUNON HA4010V4-0000-C99 */ |
| 207 |
|
| 208 |
compatible = "pwm-fan"; |
| 209 |
pwms = <&gpio0 24 4000>; |
| 210 |
}; |
| 211 |
}; |
| 212 |
|
| 213 |
&pciec { |
| 214 |
status = "okay"; |
| 215 |
|
| 216 |
/* Etron EJ168 USB 3.0 controller */ |
| 217 |
pcie@1,0 { |
| 218 |
/* Port 0, Lane 0 */ |
| 219 |
status = "okay"; |
| 220 |
}; |
| 221 |
|
| 222 |
/* First mini-PCIe port */ |
| 223 |
pcie@2,0 { |
| 224 |
/* Port 0, Lane 1 */ |
| 225 |
status = "okay"; |
| 226 |
}; |
| 227 |
|
| 228 |
/* Second mini-PCIe port */ |
| 229 |
pcie@3,0 { |
| 230 |
/* Port 0, Lane 3 */ |
| 231 |
status = "okay"; |
| 232 |
}; |
| 233 |
}; |
| 234 |
|
| 235 |
&pinctrl { |
| 236 |
|
| 237 |
keys_pin: keys-pin { |
| 238 |
marvell,pins = "mpp32", "mpp33"; |
| 239 |
marvell,function = "gpio"; |
| 240 |
}; |
| 241 |
|
| 242 |
power_led_pin: power-led-pin { |
| 243 |
marvell,pins = "mpp40"; |
| 244 |
marvell,function = "gpio"; |
| 245 |
}; |
| 246 |
|
| 247 |
gpio_fan_pin: gpio-fan-pin { |
| 248 |
marvell,pins = "mpp24"; |
| 249 |
marvell,function = "gpio"; |
| 250 |
}; |
| 251 |
}; |
| 252 |
|
| 253 |
&spi0 { |
| 254 |
status = "okay"; |
| 255 |
|
| 256 |
flash@0 { |
| 257 |
#address-cells = <1>; |
| 258 |
#size-cells = <1>; |
| 259 |
compatible = "everspin,mr25h256"; |
| 260 |
reg = <0>; /* Chip select 0 */ |
| 261 |
spi-max-frequency = <40000000>; |
| 262 |
}; |
| 263 |
}; |
| 264 |
|
| 265 |
&mdio { |
| 266 |
status = "okay"; |
| 267 |
|
| 268 |
ethernet-switch@0 { |
| 269 |
compatible = "marvell,mv88e6085"; |
| 270 |
reg = <0>; |
| 271 |
|
| 272 |
ethernet-ports { |
| 273 |
#address-cells = <1>; |
| 274 |
#size-cells = <0>; |
| 275 |
|
| 276 |
ethernet-port@0 { |
| 277 |
reg = <0>; |
| 278 |
label = "lan4"; |
| 279 |
}; |
| 280 |
|
| 281 |
ethernet-port@1 { |
| 282 |
reg = <1>; |
| 283 |
label = "lan3"; |
| 284 |
}; |
| 285 |
|
| 286 |
ethernet-port@2 { |
| 287 |
reg = <2>; |
| 288 |
label = "lan2"; |
| 289 |
}; |
| 290 |
|
| 291 |
ethernet-port@3 { |
| 292 |
reg = <3>; |
| 293 |
label = "lan1"; |
| 294 |
}; |
| 295 |
|
| 296 |
ethernet-port@4 { |
| 297 |
reg = <4>; |
| 298 |
label = "internet"; |
| 299 |
}; |
| 300 |
|
| 301 |
ethernet-port@5 { |
| 302 |
reg = <5>; |
| 303 |
phy-mode = "rgmii-id"; |
| 304 |
ethernet = <ð0>; |
| 305 |
fixed-link { |
| 306 |
speed = <1000>; |
| 307 |
full-duplex; |
| 308 |
}; |
| 309 |
}; |
| 310 |
}; |
| 311 |
}; |
| 312 |
}; |
| 313 |
|
| 314 |
&nand_controller { |
| 315 |
status = "okay"; |
| 316 |
|
| 317 |
nand@0 { |
| 318 |
reg = <0>; |
| 319 |
label = "pxa3xx_nand-0"; |
| 320 |
nand-rb = <0>; |
| 321 |
marvell,nand-keep-config; |
| 322 |
nand-on-flash-bbt; |
| 323 |
nand-ecc-strength = <4>; |
| 324 |
nand-ecc-step-size = <512>; |
| 325 |
|
| 326 |
partitions { |
| 327 |
compatible = "fixed-partitions"; |
| 328 |
#address-cells = <1>; |
| 329 |
#size-cells = <1>; |
| 330 |
|
| 331 |
partition@0 { |
| 332 |
label = "u-boot"; |
| 333 |
reg = <0x0000000 0x100000>; /* 1MB */ |
| 334 |
read-only; |
| 335 |
}; |
| 336 |
|
| 337 |
partition@100000 { |
| 338 |
label = "u_env"; |
| 339 |
reg = <0x100000 0x40000>; /* 256KB */ |
| 340 |
}; |
| 341 |
|
| 342 |
partition@140000 { |
| 343 |
label = "s_env"; |
| 344 |
reg = <0x140000 0x40000>; /* 256KB */ |
| 345 |
}; |
| 346 |
|
| 347 |
partition@900000 { |
| 348 |
label = "devinfo"; |
| 349 |
reg = <0x900000 0x100000>; /* 1MB */ |
| 350 |
read-only; |
| 351 |
}; |
| 352 |
|
| 353 |
/* kernel1 overlaps with rootfs1 by design */ |
| 354 |
partition@a00000 { |
| 355 |
label = "kernel1"; |
| 356 |
reg = <0xa00000 0x2800000>; /* 40MB */ |
| 357 |
}; |
| 358 |
|
| 359 |
partition@d00000 { |
| 360 |
label = "rootfs1"; |
| 361 |
reg = <0xd00000 0x2500000>; /* 37MB */ |
| 362 |
}; |
| 363 |
|
| 364 |
/* kernel2 overlaps with rootfs2 by design */ |
| 365 |
partition@3200000 { |
| 366 |
label = "kernel2"; |
| 367 |
reg = <0x3200000 0x2800000>; /* 40MB */ |
| 368 |
}; |
| 369 |
|
| 370 |
partition@3500000 { |
| 371 |
label = "rootfs2"; |
| 372 |
reg = <0x3500000 0x2500000>; /* 37MB */ |
| 373 |
}; |
| 374 |
|
| 375 |
/* |
| 376 |
* 38MB, last MB is for the BBT, not writable |
| 377 |
*/ |
| 378 |
partition@5a00000 { |
| 379 |
label = "syscfg"; |
| 380 |
reg = <0x5a00000 0x2600000>; |
| 381 |
}; |
| 382 |
|
| 383 |
/* |
| 384 |
* Unused area between "s_env" and "devinfo". |
| 385 |
* Moved here because otherwise the renumbered |
| 386 |
* partitions would break the bootloader |
| 387 |
* supplied bootargs |
| 388 |
*/ |
| 389 |
partition@180000 { |
| 390 |
label = "unused_area"; |
| 391 |
reg = <0x180000 0x780000>; /* 7.5MB */ |
| 392 |
}; |
| 393 |
}; |
| 394 |
}; |
| 395 |
}; |