| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Marvell OpenRD (Base|Client|Ultimate) Board Description |
| 4 |
* |
| 5 |
* Andrew Lunn <[email protected]> |
| 6 |
* |
| 7 |
* This file contains the definitions that are common between the three |
| 8 |
* variants of the Marvell Kirkwood Development Board. |
| 9 |
*/ |
| 10 |
|
| 11 |
#include "kirkwood.dtsi" |
| 12 |
#include "kirkwood-6281.dtsi" |
| 13 |
|
| 14 |
/ { |
| 15 |
memory { |
| 16 |
device_type = "memory"; |
| 17 |
reg = <0x00000000 0x20000000>; |
| 18 |
}; |
| 19 |
|
| 20 |
chosen { |
| 21 |
bootargs = "console=ttyS0,115200n8"; |
| 22 |
stdout-path = &uart0; |
| 23 |
}; |
| 24 |
|
| 25 |
ocp@f1000000 { |
| 26 |
pinctrl: pin-controller@10000 { |
| 27 |
pinctrl-0 = <&pmx_select28 &pmx_sdio_cd &pmx_select34>; |
| 28 |
pinctrl-names = "default"; |
| 29 |
|
| 30 |
pmx_select28: pmx-select-rs232-rs485 { |
| 31 |
marvell,pins = "mpp28"; |
| 32 |
marvell,function = "gpio"; |
| 33 |
}; |
| 34 |
pmx_sdio_cd: pmx-sdio-cd { |
| 35 |
marvell,pins = "mpp29"; |
| 36 |
marvell,function = "gpio"; |
| 37 |
}; |
| 38 |
pmx_select34: pmx-select-uart-sd { |
| 39 |
marvell,pins = "mpp34"; |
| 40 |
marvell,function = "gpio"; |
| 41 |
}; |
| 42 |
}; |
| 43 |
serial@12000 { |
| 44 |
status = "okay"; |
| 45 |
|
| 46 |
}; |
| 47 |
sata@80000 { |
| 48 |
status = "okay"; |
| 49 |
nr-ports = <2>; |
| 50 |
}; |
| 51 |
mvsdio@90000 { |
| 52 |
status = "okay"; |
| 53 |
cd-gpios = <&gpio0 29 9>; |
| 54 |
}; |
| 55 |
gpio@10100 { |
| 56 |
p28-hog { |
| 57 |
gpio-hog; |
| 58 |
gpios = <28 GPIO_ACTIVE_HIGH>; |
| 59 |
/* |
| 60 |
* SelRS232or485 selects between RS-232 or RS-485 |
| 61 |
* mode for the second UART. |
| 62 |
* |
| 63 |
* Low: RS-232 |
| 64 |
* High: RS-485 |
| 65 |
* |
| 66 |
* To use the second UART, you need to change also |
| 67 |
* the SelUARTorSD. |
| 68 |
*/ |
| 69 |
output-low; |
| 70 |
line-name = "SelRS232or485"; |
| 71 |
}; |
| 72 |
}; |
| 73 |
gpio@10140 { |
| 74 |
p2-hog { |
| 75 |
gpio-hog; |
| 76 |
gpios = <2 GPIO_ACTIVE_HIGH>; |
| 77 |
/* |
| 78 |
* SelUARTorSD selects between the second UART |
| 79 |
* (serial@12100) and SD (mvsdio@90000). |
| 80 |
* |
| 81 |
* Low: UART |
| 82 |
* High: SD |
| 83 |
* |
| 84 |
* When changing this line make sure the newly |
| 85 |
* selected device node is enabled and the |
| 86 |
* previously selected device node is disabled. |
| 87 |
*/ |
| 88 |
output-high; /* Select SD by default */ |
| 89 |
line-name = "SelUARTorSD"; |
| 90 |
}; |
| 91 |
}; |
| 92 |
}; |
| 93 |
}; |
| 94 |
|
| 95 |
&nand { |
| 96 |
status = "okay"; |
| 97 |
pinctrl-0 = <&pmx_nand>; |
| 98 |
pinctrl-names = "default"; |
| 99 |
|
| 100 |
partition@0 { |
| 101 |
label = "u-boot"; |
| 102 |
reg = <0x0000000 0x100000>; |
| 103 |
}; |
| 104 |
|
| 105 |
partition@100000 { |
| 106 |
label = "uImage"; |
| 107 |
reg = <0x0100000 0x400000>; |
| 108 |
}; |
| 109 |
|
| 110 |
partition@600000 { |
| 111 |
label = "root"; |
| 112 |
reg = <0x0600000 0x1FA00000>; |
| 113 |
}; |
| 114 |
}; |
| 115 |
|
| 116 |
&pciec { |
| 117 |
status = "okay"; |
| 118 |
}; |
| 119 |
|
| 120 |
&pcie0 { |
| 121 |
status = "okay"; |
| 122 |
}; |