| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/dts-v1/; |
| 3 |
|
| 4 |
#include "kirkwood.dtsi" |
| 5 |
#include "kirkwood-6281.dtsi" |
| 6 |
|
| 7 |
/ { |
| 8 |
model = "Seagate FreeAgent Dockstar"; |
| 9 |
compatible = "seagate,dockstar", "marvell,kirkwood-88f6281", "marvell,kirkwood"; |
| 10 |
|
| 11 |
memory { |
| 12 |
device_type = "memory"; |
| 13 |
reg = <0x00000000 0x8000000>; |
| 14 |
}; |
| 15 |
|
| 16 |
chosen { |
| 17 |
bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10"; |
| 18 |
stdout-path = &uart0; |
| 19 |
}; |
| 20 |
|
| 21 |
ocp@f1000000 { |
| 22 |
pinctrl: pin-controller@10000 { |
| 23 |
pmx_usb_power_enable: pmx-usb-power-enable { |
| 24 |
marvell,pins = "mpp29"; |
| 25 |
marvell,function = "gpio"; |
| 26 |
}; |
| 27 |
pmx_led_green: pmx-led-green { |
| 28 |
marvell,pins = "mpp46"; |
| 29 |
marvell,function = "gpio"; |
| 30 |
}; |
| 31 |
pmx_led_orange: pmx-led-orange { |
| 32 |
marvell,pins = "mpp47"; |
| 33 |
marvell,function = "gpio"; |
| 34 |
}; |
| 35 |
}; |
| 36 |
serial@12000 { |
| 37 |
status = "okay"; |
| 38 |
}; |
| 39 |
}; |
| 40 |
gpio-leds { |
| 41 |
compatible = "gpio-leds"; |
| 42 |
pinctrl-0 = <&pmx_led_green &pmx_led_orange>; |
| 43 |
pinctrl-names = "default"; |
| 44 |
|
| 45 |
led-health { |
| 46 |
label = "status:green:health"; |
| 47 |
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; |
| 48 |
default-state = "keep"; |
| 49 |
}; |
| 50 |
led-fault { |
| 51 |
label = "status:orange:fault"; |
| 52 |
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; |
| 53 |
}; |
| 54 |
}; |
| 55 |
regulators { |
| 56 |
compatible = "simple-bus"; |
| 57 |
#address-cells = <1>; |
| 58 |
#size-cells = <0>; |
| 59 |
pinctrl-0 = <&pmx_usb_power_enable>; |
| 60 |
pinctrl-names = "default"; |
| 61 |
|
| 62 |
usb_power: regulator@1 { |
| 63 |
compatible = "regulator-fixed"; |
| 64 |
reg = <1>; |
| 65 |
regulator-name = "USB Power"; |
| 66 |
regulator-min-microvolt = <5000000>; |
| 67 |
regulator-max-microvolt = <5000000>; |
| 68 |
enable-active-high; |
| 69 |
regulator-always-on; |
| 70 |
regulator-boot-on; |
| 71 |
gpio = <&gpio0 29 0>; |
| 72 |
}; |
| 73 |
}; |
| 74 |
}; |
| 75 |
|
| 76 |
&nand { |
| 77 |
status = "okay"; |
| 78 |
|
| 79 |
partition@0 { |
| 80 |
label = "u-boot"; |
| 81 |
reg = <0x0000000 0x100000>; |
| 82 |
read-only; |
| 83 |
}; |
| 84 |
|
| 85 |
partition@100000 { |
| 86 |
label = "uImage"; |
| 87 |
reg = <0x0100000 0x400000>; |
| 88 |
}; |
| 89 |
|
| 90 |
partition@500000 { |
| 91 |
label = "data"; |
| 92 |
reg = <0x0500000 0xfb00000>; |
| 93 |
}; |
| 94 |
}; |
| 95 |
|
| 96 |
&mdio { |
| 97 |
status = "okay"; |
| 98 |
|
| 99 |
ethphy0: ethernet-phy@0 { |
| 100 |
compatible = "marvell,88e1116"; |
| 101 |
reg = <0>; |
| 102 |
}; |
| 103 |
}; |
| 104 |
|
| 105 |
ð0 { |
| 106 |
status = "okay"; |
| 107 |
ethernet0-port@0 { |
| 108 |
phy-handle = <ðphy0>; |
| 109 |
}; |
| 110 |
}; |