| 1 |
// SPDX-License-Identifier: (GPL-2.0 OR MIT) |
| 2 |
/* |
| 3 |
* Device Tree file for Armada 385 Allied Telesis x530/GS980MX Board. |
| 4 |
(x530/AT-GS980MX) |
| 5 |
* |
| 6 |
Copyright (C) 2020 Allied Telesis Labs |
| 7 |
*/ |
| 8 |
|
| 9 |
/dts-v1/; |
| 10 |
#include "armada-385.dtsi" |
| 11 |
|
| 12 |
#include <dt-bindings/gpio/gpio.h> |
| 13 |
|
| 14 |
/ { |
| 15 |
model = "x530/AT-GS980MX"; |
| 16 |
compatible = "alliedtelesis,gs980mx", "alliedtelesis,x530", "marvell,armada385", "marvell,armada380"; |
| 17 |
|
| 18 |
chosen { |
| 19 |
stdout-path = "serial1:115200n8"; |
| 20 |
}; |
| 21 |
|
| 22 |
memory { |
| 23 |
device_type = "memory"; |
| 24 |
reg = <0x00000000 0x40000000>; /* 1GB */ |
| 25 |
}; |
| 26 |
|
| 27 |
soc { |
| 28 |
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 |
| 29 |
MBUS_ID(0x01, 0x3d) 0 0xf4800000 0x80000 |
| 30 |
MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>; |
| 31 |
|
| 32 |
internal-regs { |
| 33 |
i2c0: i2c@11000 { |
| 34 |
pinctrl-names = "default"; |
| 35 |
pinctrl-0 = <&i2c0_pins>; |
| 36 |
status = "okay"; |
| 37 |
}; |
| 38 |
|
| 39 |
uart0: serial@12000 { |
| 40 |
pinctrl-names = "default"; |
| 41 |
pinctrl-0 = <&uart0_pins>; |
| 42 |
status = "okay"; |
| 43 |
}; |
| 44 |
}; |
| 45 |
}; |
| 46 |
|
| 47 |
led-7seg { |
| 48 |
compatible = "gpio-7-segment"; |
| 49 |
segment-gpios = <&led_7seg_gpio 0 GPIO_ACTIVE_LOW>, |
| 50 |
<&led_7seg_gpio 1 GPIO_ACTIVE_LOW>, |
| 51 |
<&led_7seg_gpio 2 GPIO_ACTIVE_LOW>, |
| 52 |
<&led_7seg_gpio 3 GPIO_ACTIVE_LOW>, |
| 53 |
<&led_7seg_gpio 4 GPIO_ACTIVE_LOW>, |
| 54 |
<&led_7seg_gpio 5 GPIO_ACTIVE_LOW>, |
| 55 |
<&led_7seg_gpio 6 GPIO_ACTIVE_LOW>; |
| 56 |
}; |
| 57 |
}; |
| 58 |
|
| 59 |
&pciec { |
| 60 |
status = "okay"; |
| 61 |
}; |
| 62 |
|
| 63 |
&pcie1 { |
| 64 |
status = "okay"; |
| 65 |
reset-gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; |
| 66 |
reset-delay-us = <400000>; |
| 67 |
}; |
| 68 |
|
| 69 |
&pcie2 { |
| 70 |
status = "okay"; |
| 71 |
}; |
| 72 |
|
| 73 |
&devbus_cs1 { |
| 74 |
compatible = "marvell,mvebu-devbus"; |
| 75 |
status = "okay"; |
| 76 |
|
| 77 |
devbus,bus-width = <8>; |
| 78 |
devbus,turn-off-ps = <60000>; |
| 79 |
devbus,badr-skew-ps = <0>; |
| 80 |
devbus,acc-first-ps = <124000>; |
| 81 |
devbus,acc-next-ps = <248000>; |
| 82 |
devbus,rd-setup-ps = <0>; |
| 83 |
devbus,rd-hold-ps = <0>; |
| 84 |
|
| 85 |
/* Write parameters */ |
| 86 |
devbus,sync-enable = <0>; |
| 87 |
devbus,wr-high-ps = <60000>; |
| 88 |
devbus,wr-low-ps = <60000>; |
| 89 |
devbus,ale-wr-ps = <60000>; |
| 90 |
|
| 91 |
nvs@0 { |
| 92 |
status = "okay"; |
| 93 |
|
| 94 |
compatible = "mtd-ram"; |
| 95 |
reg = <0 0x00080000>; |
| 96 |
bank-width = <1>; |
| 97 |
label = "nvs"; |
| 98 |
}; |
| 99 |
}; |
| 100 |
|
| 101 |
&pinctrl { |
| 102 |
i2c0_gpio_pins: i2c-gpio-pins-0 { |
| 103 |
marvell,pins = "mpp2", "mpp3"; |
| 104 |
marvell,function = "gpio"; |
| 105 |
}; |
| 106 |
}; |
| 107 |
|
| 108 |
&i2c0 { |
| 109 |
clock-frequency = <100000>; |
| 110 |
status = "okay"; |
| 111 |
|
| 112 |
pinctrl-names = "default", "gpio"; |
| 113 |
pinctrl-0 = <&i2c0_pins>; |
| 114 |
pinctrl-1 = <&i2c0_gpio_pins>; |
| 115 |
scl-gpio = <&gpio0 2 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 116 |
sda-gpio = <&gpio0 3 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 117 |
|
| 118 |
i2c0mux: mux@71 { |
| 119 |
#address-cells = <1>; |
| 120 |
#size-cells = <0>; |
| 121 |
compatible = "nxp,pca9544"; |
| 122 |
reg = <0x71>; |
| 123 |
i2c-mux-idle-disconnect; |
| 124 |
|
| 125 |
i2c@0 { /* POE devices MUX */ |
| 126 |
#address-cells = <1>; |
| 127 |
#size-cells = <0>; |
| 128 |
reg = <0>; |
| 129 |
}; |
| 130 |
|
| 131 |
i2c@1 { |
| 132 |
#address-cells = <1>; |
| 133 |
#size-cells = <0>; |
| 134 |
reg = <1>; |
| 135 |
|
| 136 |
adt7476_2e: hwmon@2e { |
| 137 |
compatible = "adi,adt7476"; |
| 138 |
reg = <0x2e>; |
| 139 |
}; |
| 140 |
|
| 141 |
adt7476_2d: hwmon@2d { |
| 142 |
compatible = "adi,adt7476"; |
| 143 |
reg = <0x2d>; |
| 144 |
}; |
| 145 |
}; |
| 146 |
|
| 147 |
i2c@2 { |
| 148 |
#address-cells = <1>; |
| 149 |
#size-cells = <0>; |
| 150 |
reg = <2>; |
| 151 |
|
| 152 |
rtc@68 { |
| 153 |
compatible = "dallas,ds1340"; |
| 154 |
reg = <0x68>; |
| 155 |
}; |
| 156 |
}; |
| 157 |
|
| 158 |
i2c@3 { |
| 159 |
#address-cells = <1>; |
| 160 |
#size-cells = <0>; |
| 161 |
reg = <3>; |
| 162 |
|
| 163 |
led_7seg_gpio: gpio@20 { |
| 164 |
compatible = "nxp,pca9554"; |
| 165 |
gpio-controller; |
| 166 |
#gpio-cells = <2>; |
| 167 |
reg = <0x20>; |
| 168 |
}; |
| 169 |
}; |
| 170 |
}; |
| 171 |
}; |
| 172 |
|
| 173 |
&usb0 { |
| 174 |
status = "okay"; |
| 175 |
}; |
| 176 |
|
| 177 |
&spi1 { |
| 178 |
pinctrl-names = "default"; |
| 179 |
pinctrl-0 = <&spi1_pins>; |
| 180 |
status = "okay"; |
| 181 |
|
| 182 |
flash@1 { |
| 183 |
#address-cells = <1>; |
| 184 |
#size-cells = <1>; |
| 185 |
compatible = "jedec,spi-nor"; |
| 186 |
reg = <1>; /* Chip select 1 */ |
| 187 |
spi-max-frequency = <54000000>; |
| 188 |
|
| 189 |
partitions { |
| 190 |
compatible = "fixed-partitions"; |
| 191 |
#address-cells = <1>; |
| 192 |
#size-cells = <1>; |
| 193 |
partition@0 { |
| 194 |
reg = <0x00000000 0x00100000>; |
| 195 |
label = "u-boot"; |
| 196 |
}; |
| 197 |
partition@100000 { |
| 198 |
reg = <0x00100000 0x00040000>; |
| 199 |
label = "u-boot-env"; |
| 200 |
}; |
| 201 |
partition@140000 { |
| 202 |
reg = <0x00140000 0x00e80000>; |
| 203 |
label = "unused"; |
| 204 |
}; |
| 205 |
partition@fc0000 { |
| 206 |
reg = <0x00fc0000 0x00040000>; |
| 207 |
label = "idprom"; |
| 208 |
}; |
| 209 |
}; |
| 210 |
}; |
| 211 |
}; |
| 212 |
|
| 213 |
&nand_controller { |
| 214 |
status = "okay"; |
| 215 |
|
| 216 |
nand@0 { |
| 217 |
reg = <0>; |
| 218 |
label = "pxa3xx_nand-0"; |
| 219 |
nand-rb = <0>; |
| 220 |
nand-on-flash-bbt; |
| 221 |
nand-ecc-strength = <4>; |
| 222 |
nand-ecc-step-size = <512>; |
| 223 |
|
| 224 |
marvell,nand-enable-arbiter; |
| 225 |
|
| 226 |
partitions { |
| 227 |
compatible = "fixed-partitions"; |
| 228 |
#address-cells = <1>; |
| 229 |
#size-cells = <1>; |
| 230 |
partition@0 { |
| 231 |
reg = <0x00000000 0x0f000000>; |
| 232 |
label = "user"; |
| 233 |
}; |
| 234 |
partition@f000000 { |
| 235 |
/* Maximum mtdoops size is 8MB, so set to that. */ |
| 236 |
reg = <0x0f000000 0x00800000>; |
| 237 |
label = "errlog"; |
| 238 |
}; |
| 239 |
partition@f800000 { |
| 240 |
reg = <0x0f800000 0x00800000>; |
| 241 |
label = "nand-bbt"; |
| 242 |
}; |
| 243 |
}; |
| 244 |
}; |
| 245 |
}; |
| 246 |
|