| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Device Tree file for Marvell Armada 370 Reference Design board |
| 4 |
* (RD-88F6710-A1) |
| 5 |
* |
| 6 |
* Copied from arch/arm/boot/dts/armada-370-db.dts |
| 7 |
* |
| 8 |
* Copyright (C) 2013 Florian Fainelli <[email protected]> |
| 9 |
* |
| 10 |
* Note: this Device Tree assumes that the bootloader has remapped the |
| 11 |
* internal registers to 0xf1000000 (instead of the default |
| 12 |
* 0xd0000000). The 0xf1000000 is the default used by the recent, |
| 13 |
* DT-capable, U-Boot bootloaders provided by Marvell. Some earlier |
| 14 |
* boards were delivered with an older version of the bootloader that |
| 15 |
* left internal registers mapped at 0xd0000000. If you are in this |
| 16 |
* situation, you should either update your bootloader (preferred |
| 17 |
* solution) or the below Device Tree should be adjusted. |
| 18 |
*/ |
| 19 |
|
| 20 |
/dts-v1/; |
| 21 |
#include <dt-bindings/input/input.h> |
| 22 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 23 |
#include <dt-bindings/leds/common.h> |
| 24 |
#include <dt-bindings/gpio/gpio.h> |
| 25 |
#include "armada-370.dtsi" |
| 26 |
|
| 27 |
/ { |
| 28 |
model = "Marvell Armada 370 Reference Design"; |
| 29 |
compatible = "marvell,a370-rd", "marvell,armada370", "marvell,armada-370-xp"; |
| 30 |
|
| 31 |
chosen { |
| 32 |
stdout-path = "serial0:115200n8"; |
| 33 |
}; |
| 34 |
|
| 35 |
memory@0 { |
| 36 |
device_type = "memory"; |
| 37 |
reg = <0x00000000 0x20000000>; /* 512 MB */ |
| 38 |
}; |
| 39 |
|
| 40 |
soc { |
| 41 |
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 |
| 42 |
MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000 |
| 43 |
MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>; |
| 44 |
|
| 45 |
internal-regs { |
| 46 |
serial@12000 { |
| 47 |
status = "okay"; |
| 48 |
}; |
| 49 |
sata@a0000 { |
| 50 |
nr-ports = <2>; |
| 51 |
status = "okay"; |
| 52 |
}; |
| 53 |
|
| 54 |
ethernet@70000 { |
| 55 |
status = "okay"; |
| 56 |
phy = <&phy0>; |
| 57 |
phy-mode = "sgmii"; |
| 58 |
}; |
| 59 |
ethernet@74000 { |
| 60 |
pinctrl-0 = <&ge1_rgmii_pins>; |
| 61 |
pinctrl-names = "default"; |
| 62 |
status = "okay"; |
| 63 |
phy-mode = "rgmii-id"; |
| 64 |
fixed-link { |
| 65 |
speed = <1000>; |
| 66 |
full-duplex; |
| 67 |
}; |
| 68 |
}; |
| 69 |
|
| 70 |
mvsdio@d4000 { |
| 71 |
pinctrl-0 = <&sdio_pins1>; |
| 72 |
pinctrl-names = "default"; |
| 73 |
status = "okay"; |
| 74 |
/* No CD or WP GPIOs */ |
| 75 |
broken-cd; |
| 76 |
}; |
| 77 |
|
| 78 |
usb@50000 { |
| 79 |
status = "okay"; |
| 80 |
}; |
| 81 |
|
| 82 |
usb@51000 { |
| 83 |
status = "okay"; |
| 84 |
}; |
| 85 |
|
| 86 |
gpio-keys { |
| 87 |
compatible = "gpio-keys"; |
| 88 |
button { |
| 89 |
label = "Software Button"; |
| 90 |
linux,code = <KEY_POWER>; |
| 91 |
gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; |
| 92 |
}; |
| 93 |
}; |
| 94 |
|
| 95 |
gpio-fan { |
| 96 |
compatible = "gpio-fan"; |
| 97 |
gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>; |
| 98 |
gpio-fan,speed-map = <0 0>, <3000 1>; |
| 99 |
pinctrl-0 = <&fan_pins>; |
| 100 |
pinctrl-names = "default"; |
| 101 |
}; |
| 102 |
|
| 103 |
gpio_leds { |
| 104 |
compatible = "gpio-leds"; |
| 105 |
pinctrl-names = "default"; |
| 106 |
pinctrl-0 = <&led_pins>; |
| 107 |
|
| 108 |
sw_led { |
| 109 |
label = "370rd:green:sw"; |
| 110 |
gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; |
| 111 |
default-state = "keep"; |
| 112 |
}; |
| 113 |
}; |
| 114 |
}; |
| 115 |
}; |
| 116 |
}; |
| 117 |
|
| 118 |
&pciec { |
| 119 |
status = "okay"; |
| 120 |
|
| 121 |
/* Internal mini-PCIe connector */ |
| 122 |
pcie@1,0 { |
| 123 |
/* Port 0, Lane 0 */ |
| 124 |
status = "okay"; |
| 125 |
}; |
| 126 |
|
| 127 |
/* Internal mini-PCIe connector */ |
| 128 |
pcie@2,0 { |
| 129 |
/* Port 1, Lane 0 */ |
| 130 |
status = "okay"; |
| 131 |
}; |
| 132 |
}; |
| 133 |
|
| 134 |
&mdio { |
| 135 |
pinctrl-0 = <&mdio_pins>; |
| 136 |
pinctrl-names = "default"; |
| 137 |
phy0: ethernet-phy@0 { |
| 138 |
reg = <0>; |
| 139 |
leds { |
| 140 |
#address-cells = <1>; |
| 141 |
#size-cells = <0>; |
| 142 |
|
| 143 |
led@0 { |
| 144 |
reg = <0>; |
| 145 |
color = <LED_COLOR_ID_WHITE>; |
| 146 |
function = LED_FUNCTION_WAN; |
| 147 |
default-state = "keep"; |
| 148 |
}; |
| 149 |
}; |
| 150 |
}; |
| 151 |
|
| 152 |
switch: ethernet-switch@10 { |
| 153 |
compatible = "marvell,mv88e6085"; |
| 154 |
reg = <0x10>; |
| 155 |
interrupt-controller; |
| 156 |
#interrupt-cells = <2>; |
| 157 |
|
| 158 |
ethernet-ports { |
| 159 |
#address-cells = <1>; |
| 160 |
#size-cells = <0>; |
| 161 |
|
| 162 |
ethernet-port@0 { |
| 163 |
reg = <0>; |
| 164 |
label = "lan0"; |
| 165 |
}; |
| 166 |
|
| 167 |
ethernet-port@1 { |
| 168 |
reg = <1>; |
| 169 |
label = "lan1"; |
| 170 |
}; |
| 171 |
|
| 172 |
ethernet-port@2 { |
| 173 |
reg = <2>; |
| 174 |
label = "lan2"; |
| 175 |
}; |
| 176 |
|
| 177 |
ethernet-port@3 { |
| 178 |
reg = <3>; |
| 179 |
label = "lan3"; |
| 180 |
}; |
| 181 |
|
| 182 |
ethernet-port@5 { |
| 183 |
reg = <5>; |
| 184 |
ethernet = <ð1>; |
| 185 |
phy-mode = "rgmii-id"; |
| 186 |
fixed-link { |
| 187 |
speed = <1000>; |
| 188 |
full-duplex; |
| 189 |
}; |
| 190 |
}; |
| 191 |
}; |
| 192 |
|
| 193 |
mdio { |
| 194 |
#address-cells = <1>; |
| 195 |
#size-cells = <0>; |
| 196 |
|
| 197 |
switchphy0: ethernet-phy@0 { |
| 198 |
reg = <0>; |
| 199 |
interrupt-parent = <&switch>; |
| 200 |
interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; |
| 201 |
}; |
| 202 |
|
| 203 |
switchphy1: ethernet-phy@1 { |
| 204 |
reg = <1>; |
| 205 |
interrupt-parent = <&switch>; |
| 206 |
interrupts = <1 IRQ_TYPE_LEVEL_HIGH>; |
| 207 |
}; |
| 208 |
|
| 209 |
switchphy2: ethernet-phy@2 { |
| 210 |
reg = <2>; |
| 211 |
interrupt-parent = <&switch>; |
| 212 |
interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; |
| 213 |
}; |
| 214 |
|
| 215 |
switchphy3: ethernet-phy@3 { |
| 216 |
reg = <3>; |
| 217 |
interrupt-parent = <&switch>; |
| 218 |
interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; |
| 219 |
}; |
| 220 |
}; |
| 221 |
}; |
| 222 |
}; |
| 223 |
|
| 224 |
|
| 225 |
&pinctrl { |
| 226 |
fan_pins: fan-pins { |
| 227 |
marvell,pins = "mpp8"; |
| 228 |
marvell,function = "gpio"; |
| 229 |
}; |
| 230 |
|
| 231 |
led_pins: led-pins { |
| 232 |
marvell,pins = "mpp32"; |
| 233 |
marvell,function = "gpio"; |
| 234 |
}; |
| 235 |
}; |
| 236 |
|
| 237 |
&nand_controller { |
| 238 |
status = "okay"; |
| 239 |
|
| 240 |
nand@0 { |
| 241 |
reg = <0>; |
| 242 |
label = "pxa3xx_nand-0"; |
| 243 |
nand-rb = <0>; |
| 244 |
marvell,nand-keep-config; |
| 245 |
nand-on-flash-bbt; |
| 246 |
|
| 247 |
partitions { |
| 248 |
compatible = "fixed-partitions"; |
| 249 |
#address-cells = <1>; |
| 250 |
#size-cells = <1>; |
| 251 |
|
| 252 |
partition@0 { |
| 253 |
label = "U-Boot"; |
| 254 |
reg = <0 0x800000>; |
| 255 |
}; |
| 256 |
partition@800000 { |
| 257 |
label = "Linux"; |
| 258 |
reg = <0x800000 0x800000>; |
| 259 |
}; |
| 260 |
partition@1000000 { |
| 261 |
label = "Filesystem"; |
| 262 |
reg = <0x1000000 0x3f000000>; |
| 263 |
}; |
| 264 |
}; |
| 265 |
}; |
| 266 |
}; |