| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Device Tree file for Marvell Armada XP development board |
| 4 |
* (DB-MV784MP-GP) |
| 5 |
* |
| 6 |
* Copyright (C) 2013-2014 Marvell |
| 7 |
* |
| 8 |
* Lior Amsalem <[email protected]> |
| 9 |
* Gregory CLEMENT <[email protected]> |
| 10 |
* Thomas Petazzoni <[email protected]> |
| 11 |
* |
| 12 |
* Note: this Device Tree assumes that the bootloader has remapped the |
| 13 |
* internal registers to 0xf1000000 (instead of the default |
| 14 |
* 0xd0000000). The 0xf1000000 is the default used by the recent, |
| 15 |
* DT-capable, U-Boot bootloaders provided by Marvell. Some earlier |
| 16 |
* boards were delivered with an older version of the bootloader that |
| 17 |
* left internal registers mapped at 0xd0000000. If you are in this |
| 18 |
* situation, you should either update your bootloader (preferred |
| 19 |
* solution) or the below Device Tree should be adjusted. |
| 20 |
*/ |
| 21 |
|
| 22 |
/dts-v1/; |
| 23 |
#include <dt-bindings/gpio/gpio.h> |
| 24 |
#include "armada-xp-mv78460.dtsi" |
| 25 |
|
| 26 |
/ { |
| 27 |
model = "Marvell Armada XP Development Board DB-MV784MP-GP"; |
| 28 |
compatible = "marvell,axp-gp", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp"; |
| 29 |
|
| 30 |
chosen { |
| 31 |
stdout-path = "serial0:115200n8"; |
| 32 |
}; |
| 33 |
|
| 34 |
memory@0 { |
| 35 |
device_type = "memory"; |
| 36 |
/* |
| 37 |
* 8 GB of plug-in RAM modules by default.The amount |
| 38 |
* of memory available can be changed by the |
| 39 |
* bootloader according the size of the module |
| 40 |
* actually plugged. However, memory between |
| 41 |
* 0xF0000000 to 0xFFFFFFFF cannot be used, as it is |
| 42 |
* the address range used for I/O (internal registers, |
| 43 |
* MBus windows). |
| 44 |
*/ |
| 45 |
reg = <0x00000000 0x00000000 0x00000000 0xf0000000>, |
| 46 |
<0x00000001 0x00000000 0x00000001 0x00000000>; |
| 47 |
}; |
| 48 |
|
| 49 |
cpus { |
| 50 |
pm_pic { |
| 51 |
ctrl-gpios = <&gpio0 16 GPIO_ACTIVE_LOW>, |
| 52 |
<&gpio0 17 GPIO_ACTIVE_LOW>, |
| 53 |
<&gpio0 18 GPIO_ACTIVE_LOW>; |
| 54 |
}; |
| 55 |
}; |
| 56 |
|
| 57 |
soc { |
| 58 |
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 |
| 59 |
MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 |
| 60 |
MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000 |
| 61 |
MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000 |
| 62 |
MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000 |
| 63 |
MBUS_ID(0x0c, 0x04) 0 0 0xf1200000 0x100000>; |
| 64 |
|
| 65 |
devbus-bootcs { |
| 66 |
status = "okay"; |
| 67 |
|
| 68 |
/* Device Bus parameters are required */ |
| 69 |
|
| 70 |
/* Read parameters */ |
| 71 |
devbus,bus-width = <16>; |
| 72 |
devbus,turn-off-ps = <60000>; |
| 73 |
devbus,badr-skew-ps = <0>; |
| 74 |
devbus,acc-first-ps = <124000>; |
| 75 |
devbus,acc-next-ps = <248000>; |
| 76 |
devbus,rd-setup-ps = <0>; |
| 77 |
devbus,rd-hold-ps = <0>; |
| 78 |
|
| 79 |
/* Write parameters */ |
| 80 |
devbus,sync-enable = <0>; |
| 81 |
devbus,wr-high-ps = <60000>; |
| 82 |
devbus,wr-low-ps = <60000>; |
| 83 |
devbus,ale-wr-ps = <60000>; |
| 84 |
|
| 85 |
/* NOR 16 MiB */ |
| 86 |
nor@0 { |
| 87 |
compatible = "cfi-flash"; |
| 88 |
reg = <0 0x1000000>; |
| 89 |
bank-width = <2>; |
| 90 |
}; |
| 91 |
}; |
| 92 |
|
| 93 |
internal-regs { |
| 94 |
serial@12000 { |
| 95 |
status = "okay"; |
| 96 |
}; |
| 97 |
serial@12100 { |
| 98 |
status = "okay"; |
| 99 |
}; |
| 100 |
serial@12200 { |
| 101 |
status = "okay"; |
| 102 |
}; |
| 103 |
serial@12300 { |
| 104 |
status = "okay"; |
| 105 |
}; |
| 106 |
pinctrl { |
| 107 |
pinctrl-0 = <&pic_pins>; |
| 108 |
pinctrl-names = "default"; |
| 109 |
pic_pins: pic-pins-0 { |
| 110 |
marvell,pins = "mpp16", "mpp17", |
| 111 |
"mpp18"; |
| 112 |
marvell,function = "gpio"; |
| 113 |
}; |
| 114 |
}; |
| 115 |
sata@a0000 { |
| 116 |
nr-ports = <2>; |
| 117 |
status = "okay"; |
| 118 |
}; |
| 119 |
|
| 120 |
ethernet@70000 { |
| 121 |
status = "okay"; |
| 122 |
phy = <&phy0>; |
| 123 |
phy-mode = "qsgmii"; |
| 124 |
buffer-manager = <&bm>; |
| 125 |
bm,pool-long = <0>; |
| 126 |
}; |
| 127 |
ethernet@74000 { |
| 128 |
status = "okay"; |
| 129 |
phy = <&phy1>; |
| 130 |
phy-mode = "qsgmii"; |
| 131 |
buffer-manager = <&bm>; |
| 132 |
bm,pool-long = <1>; |
| 133 |
}; |
| 134 |
ethernet@30000 { |
| 135 |
status = "okay"; |
| 136 |
phy = <&phy2>; |
| 137 |
phy-mode = "qsgmii"; |
| 138 |
buffer-manager = <&bm>; |
| 139 |
bm,pool-long = <2>; |
| 140 |
}; |
| 141 |
ethernet@34000 { |
| 142 |
status = "okay"; |
| 143 |
phy = <&phy3>; |
| 144 |
phy-mode = "qsgmii"; |
| 145 |
buffer-manager = <&bm>; |
| 146 |
bm,pool-long = <3>; |
| 147 |
}; |
| 148 |
|
| 149 |
/* Front-side USB slot */ |
| 150 |
usb@50000 { |
| 151 |
status = "okay"; |
| 152 |
}; |
| 153 |
|
| 154 |
/* Back-side USB slot */ |
| 155 |
usb@51000 { |
| 156 |
status = "okay"; |
| 157 |
}; |
| 158 |
|
| 159 |
bm@c0000 { |
| 160 |
status = "okay"; |
| 161 |
}; |
| 162 |
|
| 163 |
nand-controller@d0000 { |
| 164 |
status = "okay"; |
| 165 |
|
| 166 |
nand@0 { |
| 167 |
reg = <0>; |
| 168 |
label = "pxa3xx_nand-0"; |
| 169 |
nand-rb = <0>; |
| 170 |
nand-on-flash-bbt; |
| 171 |
}; |
| 172 |
}; |
| 173 |
}; |
| 174 |
|
| 175 |
bm-bppi { |
| 176 |
status = "okay"; |
| 177 |
}; |
| 178 |
}; |
| 179 |
}; |
| 180 |
|
| 181 |
&pciec { |
| 182 |
status = "okay"; |
| 183 |
|
| 184 |
/* |
| 185 |
* The 3 slots are physically present as |
| 186 |
* standard PCIe slots on the board. |
| 187 |
*/ |
| 188 |
pcie@1,0 { |
| 189 |
/* Port 0, Lane 0 */ |
| 190 |
status = "okay"; |
| 191 |
}; |
| 192 |
pcie@9,0 { |
| 193 |
/* Port 2, Lane 0 */ |
| 194 |
status = "okay"; |
| 195 |
}; |
| 196 |
pcie@a,0 { |
| 197 |
/* Port 3, Lane 0 */ |
| 198 |
status = "okay"; |
| 199 |
}; |
| 200 |
}; |
| 201 |
|
| 202 |
&mdio { |
| 203 |
phy0: ethernet-phy@0 { |
| 204 |
reg = <16>; |
| 205 |
}; |
| 206 |
|
| 207 |
phy1: ethernet-phy@1 { |
| 208 |
reg = <17>; |
| 209 |
}; |
| 210 |
|
| 211 |
phy2: ethernet-phy@2 { |
| 212 |
reg = <18>; |
| 213 |
}; |
| 214 |
|
| 215 |
phy3: ethernet-phy@3 { |
| 216 |
reg = <19>; |
| 217 |
}; |
| 218 |
}; |
| 219 |
|
| 220 |
&spi0 { |
| 221 |
status = "okay"; |
| 222 |
|
| 223 |
flash@0 { |
| 224 |
#address-cells = <1>; |
| 225 |
#size-cells = <1>; |
| 226 |
compatible = "n25q128a13", "jedec,spi-nor"; |
| 227 |
reg = <0>; /* Chip select 0 */ |
| 228 |
spi-max-frequency = <108000000>; |
| 229 |
}; |
| 230 |
}; |