| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Marvell RD88F6181 Common Board descrition |
| 4 |
* |
| 5 |
* Andrew Lunn <[email protected]> |
| 6 |
* |
| 7 |
* This file contains the definitions that are common between the two |
| 8 |
* variants of the Marvell Kirkwood Development Board. |
| 9 |
*/ |
| 10 |
|
| 11 |
#include "kirkwood.dtsi" |
| 12 |
#include "kirkwood-6281.dtsi" |
| 13 |
|
| 14 |
/ { |
| 15 |
memory { |
| 16 |
device_type = "memory"; |
| 17 |
reg = <0x00000000 0x20000000>; |
| 18 |
}; |
| 19 |
|
| 20 |
chosen { |
| 21 |
bootargs = "console=ttyS0,115200n8"; |
| 22 |
stdout-path = &uart0; |
| 23 |
}; |
| 24 |
|
| 25 |
ocp@f1000000 { |
| 26 |
pinctrl: pin-controller@10000 { |
| 27 |
pinctrl-names = "default"; |
| 28 |
|
| 29 |
pmx_sdio_cd: pmx-sdio-cd { |
| 30 |
marvell,pins = "mpp28"; |
| 31 |
marvell,function = "gpio"; |
| 32 |
}; |
| 33 |
}; |
| 34 |
|
| 35 |
serial@12000 { |
| 36 |
status = "okay"; |
| 37 |
|
| 38 |
}; |
| 39 |
|
| 40 |
sata@80000 { |
| 41 |
status = "okay"; |
| 42 |
nr-ports = <2>; |
| 43 |
}; |
| 44 |
mvsdio@90000 { |
| 45 |
pinctrl-0 = <&pmx_sdio &pmx_sdio_cd>; |
| 46 |
pinctrl-names = "default"; |
| 47 |
status = "okay"; |
| 48 |
cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; |
| 49 |
/* No WP GPIO */ |
| 50 |
}; |
| 51 |
}; |
| 52 |
}; |
| 53 |
|
| 54 |
&nand { |
| 55 |
status = "okay"; |
| 56 |
|
| 57 |
partition@0 { |
| 58 |
label = "u-boot"; |
| 59 |
reg = <0x0000000 0x100000>; |
| 60 |
read-only; |
| 61 |
}; |
| 62 |
|
| 63 |
partition@100000 { |
| 64 |
label = "uImage"; |
| 65 |
reg = <0x0100000 0x200000>; |
| 66 |
}; |
| 67 |
|
| 68 |
partition@300000 { |
| 69 |
label = "rootfs"; |
| 70 |
reg = <0x0300000 0x500000>; |
| 71 |
}; |
| 72 |
}; |
| 73 |
|
| 74 |
&mdio { |
| 75 |
status = "okay"; |
| 76 |
|
| 77 |
switch: switch@0 { |
| 78 |
compatible = "marvell,mv88e6085"; |
| 79 |
#address-cells = <1>; |
| 80 |
#size-cells = <0>; |
| 81 |
|
| 82 |
ports { |
| 83 |
#address-cells = <1>; |
| 84 |
#size-cells = <0>; |
| 85 |
|
| 86 |
port@0 { |
| 87 |
reg = <0>; |
| 88 |
label = "lan1"; |
| 89 |
}; |
| 90 |
|
| 91 |
port@1 { |
| 92 |
reg = <1>; |
| 93 |
label = "lan2"; |
| 94 |
}; |
| 95 |
|
| 96 |
port@2 { |
| 97 |
reg = <2>; |
| 98 |
label = "lan3"; |
| 99 |
}; |
| 100 |
|
| 101 |
port@3 { |
| 102 |
reg = <3>; |
| 103 |
label = "lan4"; |
| 104 |
}; |
| 105 |
|
| 106 |
port@5 { |
| 107 |
reg = <5>; |
| 108 |
phy-mode = "rgmii-id"; |
| 109 |
ethernet = <ð0port>; |
| 110 |
fixed-link { |
| 111 |
speed = <1000>; |
| 112 |
full-duplex; |
| 113 |
}; |
| 114 |
}; |
| 115 |
|
| 116 |
}; |
| 117 |
}; |
| 118 |
}; |
| 119 |
|
| 120 |
ð0 { |
| 121 |
status = "okay"; |
| 122 |
ethernet0-port@0 { |
| 123 |
speed = <1000>; |
| 124 |
duplex = <1>; |
| 125 |
}; |
| 126 |
}; |
| 127 |
|
| 128 |
&pciec { |
| 129 |
status = "okay"; |
| 130 |
}; |
| 131 |
|
| 132 |
&pcie0 { |
| 133 |
status = "okay"; |
| 134 |
}; |