| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Device Tree file for Synology DS414 |
| 4 |
* |
| 5 |
* Copyright (C) 2014, Arnaud EBALARD <[email protected]> |
| 6 |
* |
| 7 |
* Note: this Device Tree assumes that the bootloader has remapped the |
| 8 |
* internal registers to 0xf1000000 (instead of the old 0xd0000000). |
| 9 |
* The 0xf1000000 is the default used by the recent, DT-capable, U-Boot |
| 10 |
* bootloaders provided by Marvell. It is used in recent versions of |
| 11 |
* DSM software provided by Synology. Nonetheless, some earlier boards |
| 12 |
* were delivered with an older version of u-boot that left internal |
| 13 |
* registers mapped at 0xd0000000. If you have such a device you will |
| 14 |
* not be able to directly boot a kernel based on this Device Tree. In |
| 15 |
* that case, the preferred solution is to update your bootloader (e.g. |
| 16 |
* by upgrading to latest version of DSM, or building a new one and |
| 17 |
* installing it from u-boot prompt) or adjust the Devive Tree |
| 18 |
* (s/0xf1000000/0xd0000000/ in 'ranges' below). |
| 19 |
*/ |
| 20 |
|
| 21 |
/dts-v1/; |
| 22 |
|
| 23 |
#include <dt-bindings/input/input.h> |
| 24 |
#include <dt-bindings/gpio/gpio.h> |
| 25 |
#include "armada-xp-mv78230.dtsi" |
| 26 |
|
| 27 |
/ { |
| 28 |
model = "Synology DS414"; |
| 29 |
compatible = "synology,ds414", "marvell,armadaxp-mv78230", |
| 30 |
"marvell,armadaxp", "marvell,armada-370-xp"; |
| 31 |
|
| 32 |
chosen { |
| 33 |
stdout-path = "serial0:115200n8"; |
| 34 |
}; |
| 35 |
|
| 36 |
memory@0 { |
| 37 |
device_type = "memory"; |
| 38 |
reg = <0 0x00000000 0 0x40000000>; /* 1GB */ |
| 39 |
}; |
| 40 |
|
| 41 |
soc { |
| 42 |
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 |
| 43 |
MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 |
| 44 |
MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000 |
| 45 |
MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000>; |
| 46 |
|
| 47 |
internal-regs { |
| 48 |
|
| 49 |
/* RTC is provided by Seiko S-35390A below */ |
| 50 |
rtc@10300 { |
| 51 |
status = "disabled"; |
| 52 |
}; |
| 53 |
|
| 54 |
i2c@11000 { |
| 55 |
clock-frequency = <400000>; |
| 56 |
status = "okay"; |
| 57 |
|
| 58 |
s35390a: s35390a@30 { |
| 59 |
compatible = "sii,s35390a"; |
| 60 |
reg = <0x30>; |
| 61 |
}; |
| 62 |
}; |
| 63 |
|
| 64 |
/* Connected to a header on device's PCB. This |
| 65 |
* provides the main console for the device. |
| 66 |
* |
| 67 |
* Warning: the device may not boot with a 3.3V |
| 68 |
* USB-serial converter connected when the power |
| 69 |
* button is pressed. The converter needs to be |
| 70 |
* connected a few seconds after pressing the |
| 71 |
* power button. This is possibly due to UART0_TXD |
| 72 |
* pin being sampled at reset (bit 0 of SAR). |
| 73 |
*/ |
| 74 |
serial@12000 { |
| 75 |
status = "okay"; |
| 76 |
}; |
| 77 |
|
| 78 |
/* Connected to a Microchip PIC16F883 for power control */ |
| 79 |
serial@12100 { |
| 80 |
status = "okay"; |
| 81 |
}; |
| 82 |
|
| 83 |
poweroff@12100 { |
| 84 |
compatible = "synology,power-off"; |
| 85 |
reg = <0x12100 0x100>; |
| 86 |
clocks = <&coreclk 0>; |
| 87 |
}; |
| 88 |
|
| 89 |
/* Front USB 2.0 port */ |
| 90 |
usb@50000 { |
| 91 |
status = "okay"; |
| 92 |
}; |
| 93 |
|
| 94 |
ethernet@70000 { |
| 95 |
status = "okay"; |
| 96 |
pinctrl-0 = <&ge0_rgmii_pins>; |
| 97 |
pinctrl-names = "default"; |
| 98 |
phy = <&phy1>; |
| 99 |
phy-mode = "rgmii-id"; |
| 100 |
}; |
| 101 |
|
| 102 |
ethernet@74000 { |
| 103 |
pinctrl-0 = <&ge1_rgmii_pins>; |
| 104 |
pinctrl-names = "default"; |
| 105 |
status = "okay"; |
| 106 |
phy = <&phy0>; |
| 107 |
phy-mode = "rgmii-id"; |
| 108 |
}; |
| 109 |
}; |
| 110 |
}; |
| 111 |
|
| 112 |
sata1_regulator: sata1-regulator-1 { |
| 113 |
compatible = "regulator-fixed"; |
| 114 |
regulator-name = "SATA1 Power"; |
| 115 |
regulator-min-microvolt = <5000000>; |
| 116 |
regulator-max-microvolt = <5000000>; |
| 117 |
startup-delay-us = <2000000>; |
| 118 |
enable-active-high; |
| 119 |
regulator-always-on; |
| 120 |
regulator-boot-on; |
| 121 |
gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>; |
| 122 |
pinctrl-0 = <&sata1_pwr_pin>; |
| 123 |
pinctrl-names = "default"; |
| 124 |
}; |
| 125 |
|
| 126 |
sata2_regulator: sata2-regulator-2 { |
| 127 |
compatible = "regulator-fixed"; |
| 128 |
regulator-name = "SATA2 Power"; |
| 129 |
regulator-min-microvolt = <5000000>; |
| 130 |
regulator-max-microvolt = <5000000>; |
| 131 |
startup-delay-us = <4000000>; |
| 132 |
enable-active-high; |
| 133 |
regulator-always-on; |
| 134 |
regulator-boot-on; |
| 135 |
gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; |
| 136 |
pinctrl-0 = <&sata2_pwr_pin>; |
| 137 |
pinctrl-names = "default"; |
| 138 |
}; |
| 139 |
|
| 140 |
sata3_regulator: sata3-regulator-3 { |
| 141 |
compatible = "regulator-fixed"; |
| 142 |
regulator-name = "SATA3 Power"; |
| 143 |
regulator-min-microvolt = <5000000>; |
| 144 |
regulator-max-microvolt = <5000000>; |
| 145 |
startup-delay-us = <6000000>; |
| 146 |
enable-active-high; |
| 147 |
regulator-always-on; |
| 148 |
regulator-boot-on; |
| 149 |
gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; |
| 150 |
pinctrl-0 = <&sata3_pwr_pin>; |
| 151 |
pinctrl-names = "default"; |
| 152 |
}; |
| 153 |
|
| 154 |
sata4_regulator: sata4-regulator-4 { |
| 155 |
compatible = "regulator-fixed"; |
| 156 |
regulator-name = "SATA4 Power"; |
| 157 |
regulator-min-microvolt = <5000000>; |
| 158 |
regulator-max-microvolt = <5000000>; |
| 159 |
startup-delay-us = <8000000>; |
| 160 |
enable-active-high; |
| 161 |
regulator-always-on; |
| 162 |
regulator-boot-on; |
| 163 |
gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>; |
| 164 |
pinctrl-0 = <&sata4_pwr_pin>; |
| 165 |
pinctrl-names = "default"; |
| 166 |
}; |
| 167 |
}; |
| 168 |
|
| 169 |
&pciec { |
| 170 |
status = "okay"; |
| 171 |
|
| 172 |
/* |
| 173 |
* Connected to Marvell 88SX7042 SATA-II controller |
| 174 |
* handling the four disks. |
| 175 |
*/ |
| 176 |
pcie@1,0 { |
| 177 |
/* Port 0, Lane 0 */ |
| 178 |
status = "okay"; |
| 179 |
}; |
| 180 |
|
| 181 |
/* |
| 182 |
* Connected to EtronTech EJ168A XHCI controller |
| 183 |
* providing the two rear USB 3.0 ports. |
| 184 |
*/ |
| 185 |
pcie@5,0 { |
| 186 |
/* Port 1, Lane 0 */ |
| 187 |
status = "okay"; |
| 188 |
}; |
| 189 |
}; |
| 190 |
|
| 191 |
|
| 192 |
&mdio { |
| 193 |
phy0: ethernet-phy@0 { /* Marvell 88E1512 */ |
| 194 |
reg = <0>; |
| 195 |
}; |
| 196 |
|
| 197 |
phy1: ethernet-phy@1 { /* Marvell 88E1512 */ |
| 198 |
reg = <1>; |
| 199 |
}; |
| 200 |
}; |
| 201 |
|
| 202 |
&pinctrl { |
| 203 |
sata1_pwr_pin: sata1-pwr-pin { |
| 204 |
marvell,pins = "mpp42"; |
| 205 |
marvell,function = "gpio"; |
| 206 |
}; |
| 207 |
|
| 208 |
sata2_pwr_pin: sata2-pwr-pin { |
| 209 |
marvell,pins = "mpp44"; |
| 210 |
marvell,function = "gpio"; |
| 211 |
}; |
| 212 |
|
| 213 |
sata3_pwr_pin: sata3-pwr-pin { |
| 214 |
marvell,pins = "mpp45"; |
| 215 |
marvell,function = "gpio"; |
| 216 |
}; |
| 217 |
|
| 218 |
sata4_pwr_pin: sata4-pwr-pin { |
| 219 |
marvell,pins = "mpp46"; |
| 220 |
marvell,function = "gpio"; |
| 221 |
}; |
| 222 |
|
| 223 |
sata1_pres_pin: sata1-pres-pin { |
| 224 |
marvell,pins = "mpp34"; |
| 225 |
marvell,function = "gpio"; |
| 226 |
}; |
| 227 |
|
| 228 |
sata2_pres_pin: sata2-pres-pin { |
| 229 |
marvell,pins = "mpp35"; |
| 230 |
marvell,function = "gpio"; |
| 231 |
}; |
| 232 |
|
| 233 |
sata3_pres_pin: sata3-pres-pin { |
| 234 |
marvell,pins = "mpp40"; |
| 235 |
marvell,function = "gpio"; |
| 236 |
}; |
| 237 |
|
| 238 |
sata4_pres_pin: sata4-pres-pin { |
| 239 |
marvell,pins = "mpp41"; |
| 240 |
marvell,function = "gpio"; |
| 241 |
}; |
| 242 |
|
| 243 |
syno_id_bit0_pin: syno-id-bit0-pin { |
| 244 |
marvell,pins = "mpp26"; |
| 245 |
marvell,function = "gpio"; |
| 246 |
}; |
| 247 |
|
| 248 |
syno_id_bit1_pin: syno-id-bit1-pin { |
| 249 |
marvell,pins = "mpp28"; |
| 250 |
marvell,function = "gpio"; |
| 251 |
}; |
| 252 |
|
| 253 |
syno_id_bit2_pin: syno-id-bit2-pin { |
| 254 |
marvell,pins = "mpp29"; |
| 255 |
marvell,function = "gpio"; |
| 256 |
}; |
| 257 |
|
| 258 |
fan1_alarm_pin: fan1-alarm-pin { |
| 259 |
marvell,pins = "mpp33"; |
| 260 |
marvell,function = "gpio"; |
| 261 |
}; |
| 262 |
|
| 263 |
fan2_alarm_pin: fan2-alarm-pin { |
| 264 |
marvell,pins = "mpp32"; |
| 265 |
marvell,function = "gpio"; |
| 266 |
}; |
| 267 |
}; |
| 268 |
|
| 269 |
&spi0 { |
| 270 |
status = "okay"; |
| 271 |
|
| 272 |
flash@0 { |
| 273 |
#address-cells = <1>; |
| 274 |
#size-cells = <1>; |
| 275 |
compatible = "micron,n25q064", "jedec,spi-nor"; |
| 276 |
reg = <0>; /* Chip select 0 */ |
| 277 |
spi-max-frequency = <20000000>; |
| 278 |
|
| 279 |
/* |
| 280 |
* Warning! |
| 281 |
* |
| 282 |
* Synology u-boot uses its compiled-in environment |
| 283 |
* and it seems Synology did not care to change u-boot |
| 284 |
* default configuration in order to allow saving a |
| 285 |
* modified environment at a sensible location. So, |
| 286 |
* if you do a 'saveenv' under u-boot, your modified |
| 287 |
* environment will be saved at 1MB after the start |
| 288 |
* of the flash, i.e. in the middle of the uImage. |
| 289 |
* For that reason, it is strongly advised not to |
| 290 |
* change the default environment, unless you know |
| 291 |
* what you are doing. |
| 292 |
*/ |
| 293 |
partition@0 { /* u-boot */ |
| 294 |
label = "RedBoot"; |
| 295 |
reg = <0x00000000 0x000d0000>; /* 832KB */ |
| 296 |
}; |
| 297 |
|
| 298 |
partition@c0000 { /* uImage */ |
| 299 |
label = "zImage"; |
| 300 |
reg = <0x000d0000 0x002d0000>; /* 2880KB */ |
| 301 |
}; |
| 302 |
|
| 303 |
partition@3a0000 { /* uInitramfs */ |
| 304 |
label = "rd.gz"; |
| 305 |
reg = <0x003a0000 0x00430000>; /* 4250KB */ |
| 306 |
}; |
| 307 |
|
| 308 |
partition@7d0000 { /* MAC address and serial number */ |
| 309 |
label = "vendor"; |
| 310 |
reg = <0x007d0000 0x00010000>; /* 64KB */ |
| 311 |
}; |
| 312 |
|
| 313 |
partition@7e0000 { |
| 314 |
label = "RedBoot config"; |
| 315 |
reg = <0x007e0000 0x00010000>; /* 64KB */ |
| 316 |
}; |
| 317 |
|
| 318 |
partition@7f0000 { |
| 319 |
label = "FIS directory"; |
| 320 |
reg = <0x007f0000 0x00010000>; /* 64KB */ |
| 321 |
}; |
| 322 |
}; |
| 323 |
}; |