| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
// Copyright (C) 2012 Thomas Petazzoni <[email protected]> |
| 3 |
|
| 4 |
/* |
| 5 |
* TODO: add Orion USB device port init when kernel.org support is added. |
| 6 |
* TODO: add flash write support: see below. |
| 7 |
* TODO: add power-off support. |
| 8 |
* TODO: add I2C EEPROM support. |
| 9 |
*/ |
| 10 |
|
| 11 |
/dts-v1/; |
| 12 |
|
| 13 |
#include <dt-bindings/gpio/gpio.h> |
| 14 |
#include <dt-bindings/input/input.h> |
| 15 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 16 |
#include "orion5x-mv88f5182.dtsi" |
| 17 |
|
| 18 |
/ { |
| 19 |
model = "LaCie Ethernet Disk mini V2"; |
| 20 |
compatible = "lacie,ethernet-disk-mini-v2", "marvell,orion5x-88f5182", "marvell,orion5x"; |
| 21 |
|
| 22 |
memory { |
| 23 |
device_type = "memory"; |
| 24 |
reg = <0x00000000 0x4000000>; /* 64 MB */ |
| 25 |
}; |
| 26 |
|
| 27 |
chosen { |
| 28 |
bootargs = "console=ttyS0,115200n8 earlyprintk"; |
| 29 |
stdout-path = &uart0; |
| 30 |
}; |
| 31 |
|
| 32 |
soc { |
| 33 |
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>, |
| 34 |
<MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>, |
| 35 |
<MBUS_ID(0x01, 0x0f) 0 0xfff80000 0x80000>; |
| 36 |
}; |
| 37 |
|
| 38 |
gpio-keys { |
| 39 |
compatible = "gpio-keys"; |
| 40 |
pinctrl-0 = <&pmx_power_button>; |
| 41 |
pinctrl-names = "default"; |
| 42 |
|
| 43 |
button-1 { |
| 44 |
label = "Power-on Switch"; |
| 45 |
linux,code = <KEY_POWER>; |
| 46 |
gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; |
| 47 |
}; |
| 48 |
}; |
| 49 |
|
| 50 |
gpio-leds { |
| 51 |
compatible = "gpio-leds"; |
| 52 |
pinctrl-0 = <&pmx_power_led>; |
| 53 |
pinctrl-names = "default"; |
| 54 |
|
| 55 |
led-1 { |
| 56 |
label = "power:blue"; |
| 57 |
gpios = <&gpio0 16 GPIO_ACTIVE_LOW>; |
| 58 |
}; |
| 59 |
}; |
| 60 |
}; |
| 61 |
|
| 62 |
&devbus_bootcs { |
| 63 |
status = "okay"; |
| 64 |
|
| 65 |
/* Read parameters */ |
| 66 |
devbus,bus-width = <8>; |
| 67 |
devbus,turn-off-ps = <90000>; |
| 68 |
devbus,badr-skew-ps = <0>; |
| 69 |
devbus,acc-first-ps = <186000>; |
| 70 |
devbus,acc-next-ps = <186000>; |
| 71 |
|
| 72 |
/* Write parameters */ |
| 73 |
devbus,wr-high-ps = <90000>; |
| 74 |
devbus,wr-low-ps = <90000>; |
| 75 |
devbus,ale-wr-ps = <90000>; |
| 76 |
|
| 77 |
/* |
| 78 |
* Currently the MTD code does not recognize the MX29LV400CBCT |
| 79 |
* as a bottom-type device. This could cause risks of |
| 80 |
* accidentally erasing critical flash sectors. We thus define |
| 81 |
* a single, write-protected partition covering the whole |
| 82 |
* flash. TODO: once the flash part TOP/BOTTOM detection |
| 83 |
* issue is sorted out in the MTD code, break this into at |
| 84 |
* least three partitions: 'u-boot code', 'u-boot environment' |
| 85 |
* and 'whatever is left'. |
| 86 |
*/ |
| 87 |
flash@0 { |
| 88 |
compatible = "cfi-flash"; |
| 89 |
reg = <0 0x80000>; |
| 90 |
bank-width = <1>; |
| 91 |
#address-cells = <1>; |
| 92 |
#size-cells = <1>; |
| 93 |
|
| 94 |
partition@0 { |
| 95 |
label = "Full512Kb"; |
| 96 |
reg = <0 0x80000>; |
| 97 |
read-only; |
| 98 |
}; |
| 99 |
}; |
| 100 |
}; |
| 101 |
|
| 102 |
&ehci0 { |
| 103 |
status = "okay"; |
| 104 |
}; |
| 105 |
|
| 106 |
ð { |
| 107 |
status = "okay"; |
| 108 |
|
| 109 |
ethernet-port@0 { |
| 110 |
phy-handle = <ðphy>; |
| 111 |
}; |
| 112 |
}; |
| 113 |
|
| 114 |
&i2c { |
| 115 |
status = "okay"; |
| 116 |
clock-frequency = <100000>; |
| 117 |
#address-cells = <1>; |
| 118 |
|
| 119 |
rtc@32 { |
| 120 |
compatible = "ricoh,rs5c372a"; |
| 121 |
reg = <0x32>; |
| 122 |
interrupt-parent = <&gpio0>; |
| 123 |
interrupts = <3 IRQ_TYPE_LEVEL_LOW>; |
| 124 |
}; |
| 125 |
}; |
| 126 |
|
| 127 |
&mdio { |
| 128 |
status = "okay"; |
| 129 |
|
| 130 |
ethphy: ethernet-phy { |
| 131 |
reg = <8>; |
| 132 |
}; |
| 133 |
}; |
| 134 |
|
| 135 |
&pinctrl { |
| 136 |
pinctrl-0 = <&pmx_rtc &pmx_power_led_ctrl>; |
| 137 |
pinctrl-names = "default"; |
| 138 |
|
| 139 |
pmx_power_button: pmx-power-button { |
| 140 |
marvell,pins = "mpp18"; |
| 141 |
marvell,function = "gpio"; |
| 142 |
}; |
| 143 |
|
| 144 |
pmx_power_led: pmx-power-led { |
| 145 |
marvell,pins = "mpp16"; |
| 146 |
marvell,function = "gpio"; |
| 147 |
}; |
| 148 |
|
| 149 |
pmx_power_led_ctrl: pmx-power-led-ctrl { |
| 150 |
marvell,pins = "mpp17"; |
| 151 |
marvell,function = "gpio"; |
| 152 |
}; |
| 153 |
|
| 154 |
pmx_rtc: pmx-rtc { |
| 155 |
marvell,pins = "mpp3"; |
| 156 |
marvell,function = "gpio"; |
| 157 |
}; |
| 158 |
}; |
| 159 |
|
| 160 |
&sata { |
| 161 |
pinctrl-0 = <&pmx_sata0 &pmx_sata1>; |
| 162 |
pinctrl-names = "default"; |
| 163 |
status = "okay"; |
| 164 |
nr-ports = <2>; |
| 165 |
}; |
| 166 |
|
| 167 |
&uart0 { |
| 168 |
status = "okay"; |
| 169 |
}; |