| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
#include <dt-bindings/input/input.h> |
| 3 |
#include <dt-bindings/gpio/gpio.h> |
| 4 |
|
| 5 |
#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16)) |
| 6 |
|
| 7 |
/ { |
| 8 |
#address-cells = <1>; |
| 9 |
#size-cells = <1>; |
| 10 |
compatible = "marvell,kirkwood"; |
| 11 |
interrupt-parent = <&intc>; |
| 12 |
|
| 13 |
cpus { |
| 14 |
#address-cells = <1>; |
| 15 |
#size-cells = <0>; |
| 16 |
|
| 17 |
cpu@0 { |
| 18 |
device_type = "cpu"; |
| 19 |
compatible = "marvell,feroceon"; |
| 20 |
reg = <0>; |
| 21 |
clocks = <&core_clk 1>, <&core_clk 3>, <&gate_clk 11>; |
| 22 |
clock-names = "cpu_clk", "ddrclk", "powersave"; |
| 23 |
}; |
| 24 |
}; |
| 25 |
|
| 26 |
aliases { |
| 27 |
gpio0 = &gpio0; |
| 28 |
gpio1 = &gpio1; |
| 29 |
i2c0 = &i2c0; |
| 30 |
}; |
| 31 |
|
| 32 |
mbus@f1000000 { |
| 33 |
compatible = "marvell,kirkwood-mbus", "simple-bus"; |
| 34 |
#address-cells = <2>; |
| 35 |
#size-cells = <1>; |
| 36 |
/* If a board file needs to change this ranges it must replace it completely */ |
| 37 |
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 /* internal-regs */ |
| 38 |
MBUS_ID(0x01, 0x2f) 0 0xf4000000 0x10000 /* nand flash */ |
| 39 |
MBUS_ID(0x03, 0x01) 0 0xf5000000 0x10000 /* crypto sram */ |
| 40 |
>; |
| 41 |
controller = <&mbusc>; |
| 42 |
pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256 MiB memory space */ |
| 43 |
pcie-io-aperture = <0xf2000000 0x100000>; /* 1 MiB I/O space */ |
| 44 |
|
| 45 |
nand: nand@12f { |
| 46 |
#address-cells = <1>; |
| 47 |
#size-cells = <1>; |
| 48 |
cle = <0>; |
| 49 |
ale = <1>; |
| 50 |
bank-width = <1>; |
| 51 |
compatible = "marvell,orion-nand"; |
| 52 |
reg = <MBUS_ID(0x01, 0x2f) 0 0x400>; |
| 53 |
chip-delay = <25>; |
| 54 |
/* set partition map and/or chip-delay in board dts */ |
| 55 |
clocks = <&gate_clk 7>; |
| 56 |
pinctrl-0 = <&pmx_nand>; |
| 57 |
pinctrl-names = "default"; |
| 58 |
status = "disabled"; |
| 59 |
}; |
| 60 |
|
| 61 |
crypto_sram: sa-sram@301 { |
| 62 |
compatible = "mmio-sram"; |
| 63 |
reg = <MBUS_ID(0x03, 0x01) 0x0 0x800>; |
| 64 |
clocks = <&gate_clk 17>; |
| 65 |
#address-cells = <1>; |
| 66 |
#size-cells = <1>; |
| 67 |
}; |
| 68 |
}; |
| 69 |
|
| 70 |
ocp@f1000000 { |
| 71 |
compatible = "simple-bus"; |
| 72 |
ranges = <0x00000000 0xf1000000 0x0100000>; |
| 73 |
#address-cells = <1>; |
| 74 |
#size-cells = <1>; |
| 75 |
|
| 76 |
pinctrl: pin-controller@10000 { |
| 77 |
/* set compatible property in SoC file */ |
| 78 |
reg = <0x10000 0x20>; |
| 79 |
|
| 80 |
pmx_ge1: pmx-ge1 { |
| 81 |
marvell,pins = "mpp20", "mpp21", "mpp22", "mpp23", |
| 82 |
"mpp24", "mpp25", "mpp26", "mpp27", |
| 83 |
"mpp30", "mpp31", "mpp32", "mpp33"; |
| 84 |
marvell,function = "ge1"; |
| 85 |
}; |
| 86 |
|
| 87 |
pmx_nand: pmx-nand { |
| 88 |
marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3", |
| 89 |
"mpp4", "mpp5", "mpp18", "mpp19"; |
| 90 |
marvell,function = "nand"; |
| 91 |
}; |
| 92 |
|
| 93 |
/* |
| 94 |
* Default SPI0 pinctrl setting with CSn on mpp0, |
| 95 |
* overwrite marvell,pins on board level if required. |
| 96 |
*/ |
| 97 |
pmx_spi: pmx-spi { |
| 98 |
marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3"; |
| 99 |
marvell,function = "spi"; |
| 100 |
}; |
| 101 |
|
| 102 |
pmx_twsi0: pmx-twsi0 { |
| 103 |
marvell,pins = "mpp8", "mpp9"; |
| 104 |
marvell,function = "twsi0"; |
| 105 |
}; |
| 106 |
|
| 107 |
/* |
| 108 |
* Default UART pinctrl setting without RTS/CTS, |
| 109 |
* overwrite marvell,pins on board level if required. |
| 110 |
*/ |
| 111 |
pmx_uart0: pmx-uart0 { |
| 112 |
marvell,pins = "mpp10", "mpp11"; |
| 113 |
marvell,function = "uart0"; |
| 114 |
}; |
| 115 |
|
| 116 |
pmx_uart1: pmx-uart1 { |
| 117 |
marvell,pins = "mpp13", "mpp14"; |
| 118 |
marvell,function = "uart1"; |
| 119 |
}; |
| 120 |
}; |
| 121 |
|
| 122 |
core_clk: core-clocks@10030 { |
| 123 |
compatible = "marvell,kirkwood-core-clock"; |
| 124 |
reg = <0x10030 0x4>; |
| 125 |
#clock-cells = <1>; |
| 126 |
}; |
| 127 |
|
| 128 |
spi0: spi@10600 { |
| 129 |
compatible = "marvell,orion-spi"; |
| 130 |
#address-cells = <1>; |
| 131 |
#size-cells = <0>; |
| 132 |
cell-index = <0>; |
| 133 |
interrupts = <23>; |
| 134 |
reg = <0x10600 0x28>; |
| 135 |
clocks = <&gate_clk 7>; |
| 136 |
pinctrl-0 = <&pmx_spi>; |
| 137 |
pinctrl-names = "default"; |
| 138 |
status = "disabled"; |
| 139 |
}; |
| 140 |
|
| 141 |
gpio0: gpio@10100 { |
| 142 |
compatible = "marvell,orion-gpio"; |
| 143 |
#gpio-cells = <2>; |
| 144 |
gpio-controller; |
| 145 |
reg = <0x10100 0x40>; |
| 146 |
ngpios = <32>; |
| 147 |
interrupt-controller; |
| 148 |
#interrupt-cells = <2>; |
| 149 |
interrupts = <35>, <36>, <37>, <38>; |
| 150 |
clocks = <&gate_clk 7>; |
| 151 |
}; |
| 152 |
|
| 153 |
gpio1: gpio@10140 { |
| 154 |
compatible = "marvell,orion-gpio"; |
| 155 |
#gpio-cells = <2>; |
| 156 |
gpio-controller; |
| 157 |
reg = <0x10140 0x40>; |
| 158 |
ngpios = <18>; |
| 159 |
interrupt-controller; |
| 160 |
#interrupt-cells = <2>; |
| 161 |
interrupts = <39>, <40>, <41>; |
| 162 |
clocks = <&gate_clk 7>; |
| 163 |
}; |
| 164 |
|
| 165 |
i2c0: i2c@11000 { |
| 166 |
compatible = "marvell,mv64xxx-i2c"; |
| 167 |
reg = <0x11000 0x20>; |
| 168 |
#address-cells = <1>; |
| 169 |
#size-cells = <0>; |
| 170 |
interrupts = <29>; |
| 171 |
clock-frequency = <100000>; |
| 172 |
clocks = <&gate_clk 7>; |
| 173 |
pinctrl-0 = <&pmx_twsi0>; |
| 174 |
pinctrl-names = "default"; |
| 175 |
status = "disabled"; |
| 176 |
}; |
| 177 |
|
| 178 |
uart0: serial@12000 { |
| 179 |
compatible = "ns16550a"; |
| 180 |
reg = <0x12000 0x100>; |
| 181 |
reg-shift = <2>; |
| 182 |
interrupts = <33>; |
| 183 |
clocks = <&gate_clk 7>; |
| 184 |
pinctrl-0 = <&pmx_uart0>; |
| 185 |
pinctrl-names = "default"; |
| 186 |
status = "disabled"; |
| 187 |
}; |
| 188 |
|
| 189 |
uart1: serial@12100 { |
| 190 |
compatible = "ns16550a"; |
| 191 |
reg = <0x12100 0x100>; |
| 192 |
reg-shift = <2>; |
| 193 |
interrupts = <34>; |
| 194 |
clocks = <&gate_clk 7>; |
| 195 |
pinctrl-0 = <&pmx_uart1>; |
| 196 |
pinctrl-names = "default"; |
| 197 |
status = "disabled"; |
| 198 |
}; |
| 199 |
|
| 200 |
mbusc: mbus-controller@20000 { |
| 201 |
compatible = "marvell,mbus-controller"; |
| 202 |
reg = <0x20000 0x80>, <0x1500 0x20>; |
| 203 |
}; |
| 204 |
|
| 205 |
sysc: system-controller@20000 { |
| 206 |
compatible = "marvell,orion-system-controller"; |
| 207 |
reg = <0x20000 0x120>; |
| 208 |
}; |
| 209 |
|
| 210 |
bridge_intc: bridge-interrupt-ctrl@20110 { |
| 211 |
compatible = "marvell,orion-bridge-intc"; |
| 212 |
interrupt-controller; |
| 213 |
#interrupt-cells = <1>; |
| 214 |
reg = <0x20110 0x8>; |
| 215 |
interrupts = <1>; |
| 216 |
marvell,#interrupts = <6>; |
| 217 |
}; |
| 218 |
|
| 219 |
gate_clk: clock-gating-control@2011c { |
| 220 |
compatible = "marvell,kirkwood-gating-clock"; |
| 221 |
reg = <0x2011c 0x4>; |
| 222 |
clocks = <&core_clk 0>; |
| 223 |
#clock-cells = <1>; |
| 224 |
}; |
| 225 |
|
| 226 |
l2: l2-cache@20128 { |
| 227 |
compatible = "marvell,kirkwood-cache"; |
| 228 |
reg = <0x20128 0x4>; |
| 229 |
}; |
| 230 |
|
| 231 |
intc: interrupt-controller@20200 { |
| 232 |
compatible = "marvell,orion-intc"; |
| 233 |
interrupt-controller; |
| 234 |
#interrupt-cells = <1>; |
| 235 |
reg = <0x20200 0x10>, <0x20210 0x10>; |
| 236 |
}; |
| 237 |
|
| 238 |
timer: timer@20300 { |
| 239 |
compatible = "marvell,orion-timer"; |
| 240 |
reg = <0x20300 0x20>; |
| 241 |
interrupt-parent = <&bridge_intc>; |
| 242 |
interrupts = <1>, <2>; |
| 243 |
clocks = <&core_clk 0>; |
| 244 |
}; |
| 245 |
|
| 246 |
wdt: watchdog-timer@20300 { |
| 247 |
compatible = "marvell,orion-wdt"; |
| 248 |
reg = <0x20300 0x28>, <0x20108 0x4>; |
| 249 |
interrupt-parent = <&bridge_intc>; |
| 250 |
interrupts = <3>; |
| 251 |
clocks = <&gate_clk 7>; |
| 252 |
status = "okay"; |
| 253 |
}; |
| 254 |
|
| 255 |
cesa: crypto@30000 { |
| 256 |
compatible = "marvell,kirkwood-crypto"; |
| 257 |
reg = <0x30000 0x10000>; |
| 258 |
reg-names = "regs"; |
| 259 |
interrupts = <22>; |
| 260 |
clocks = <&gate_clk 17>; |
| 261 |
marvell,crypto-srams = <&crypto_sram>; |
| 262 |
marvell,crypto-sram-size = <0x800>; |
| 263 |
status = "okay"; |
| 264 |
}; |
| 265 |
|
| 266 |
usb0: usb@50000 { |
| 267 |
compatible = "marvell,orion-ehci"; |
| 268 |
reg = <0x50000 0x1000>; |
| 269 |
interrupts = <19>; |
| 270 |
clocks = <&gate_clk 3>; |
| 271 |
status = "okay"; |
| 272 |
}; |
| 273 |
|
| 274 |
dma0: xor@60800 { |
| 275 |
compatible = "marvell,orion-xor"; |
| 276 |
reg = <0x60800 0x100 |
| 277 |
0x60A00 0x100>; |
| 278 |
status = "okay"; |
| 279 |
clocks = <&gate_clk 8>; |
| 280 |
|
| 281 |
xor00 { |
| 282 |
interrupts = <5>; |
| 283 |
dmacap,memcpy; |
| 284 |
dmacap,xor; |
| 285 |
}; |
| 286 |
xor01 { |
| 287 |
interrupts = <6>; |
| 288 |
dmacap,memcpy; |
| 289 |
dmacap,xor; |
| 290 |
dmacap,memset; |
| 291 |
}; |
| 292 |
}; |
| 293 |
|
| 294 |
dma1: xor@60900 { |
| 295 |
compatible = "marvell,orion-xor"; |
| 296 |
reg = <0x60900 0x100 |
| 297 |
0x60B00 0x100>; |
| 298 |
status = "okay"; |
| 299 |
clocks = <&gate_clk 16>; |
| 300 |
|
| 301 |
xor00 { |
| 302 |
interrupts = <7>; |
| 303 |
dmacap,memcpy; |
| 304 |
dmacap,xor; |
| 305 |
}; |
| 306 |
xor01 { |
| 307 |
interrupts = <8>; |
| 308 |
dmacap,memcpy; |
| 309 |
dmacap,xor; |
| 310 |
dmacap,memset; |
| 311 |
}; |
| 312 |
}; |
| 313 |
|
| 314 |
eth0: ethernet-controller@72000 { |
| 315 |
compatible = "marvell,kirkwood-eth"; |
| 316 |
#address-cells = <1>; |
| 317 |
#size-cells = <0>; |
| 318 |
reg = <0x72000 0x4000>; |
| 319 |
clocks = <&gate_clk 0>; |
| 320 |
marvell,tx-checksum-limit = <1600>; |
| 321 |
status = "disabled"; |
| 322 |
|
| 323 |
eth0port: ethernet0-port@0 { |
| 324 |
compatible = "marvell,kirkwood-eth-port"; |
| 325 |
reg = <0>; |
| 326 |
interrupts = <11>; |
| 327 |
/* overwrite MAC address in bootloader */ |
| 328 |
local-mac-address = [00 00 00 00 00 00]; |
| 329 |
/* set phy-handle property in board file */ |
| 330 |
}; |
| 331 |
}; |
| 332 |
|
| 333 |
mdio: mdio-bus@72004 { |
| 334 |
compatible = "marvell,orion-mdio"; |
| 335 |
#address-cells = <1>; |
| 336 |
#size-cells = <0>; |
| 337 |
reg = <0x72004 0x84>; |
| 338 |
interrupts = <46>; |
| 339 |
clocks = <&gate_clk 0>; |
| 340 |
status = "disabled"; |
| 341 |
|
| 342 |
/* add phy nodes in board file */ |
| 343 |
}; |
| 344 |
|
| 345 |
eth1: ethernet-controller@76000 { |
| 346 |
compatible = "marvell,kirkwood-eth"; |
| 347 |
#address-cells = <1>; |
| 348 |
#size-cells = <0>; |
| 349 |
reg = <0x76000 0x4000>; |
| 350 |
clocks = <&gate_clk 19>; |
| 351 |
marvell,tx-checksum-limit = <1600>; |
| 352 |
pinctrl-0 = <&pmx_ge1>; |
| 353 |
pinctrl-names = "default"; |
| 354 |
status = "disabled"; |
| 355 |
|
| 356 |
eth1port: ethernet1-port@0 { |
| 357 |
compatible = "marvell,kirkwood-eth-port"; |
| 358 |
reg = <0>; |
| 359 |
interrupts = <15>; |
| 360 |
/* overwrite MAC address in bootloader */ |
| 361 |
local-mac-address = [00 00 00 00 00 00]; |
| 362 |
/* set phy-handle property in board file */ |
| 363 |
}; |
| 364 |
}; |
| 365 |
|
| 366 |
sata_phy0: sata-phy@82000 { |
| 367 |
compatible = "marvell,mvebu-sata-phy"; |
| 368 |
reg = <0x82000 0x0334>; |
| 369 |
clocks = <&gate_clk 14>; |
| 370 |
clock-names = "sata"; |
| 371 |
#phy-cells = <0>; |
| 372 |
status = "okay"; |
| 373 |
}; |
| 374 |
|
| 375 |
sata_phy1: sata-phy@84000 { |
| 376 |
compatible = "marvell,mvebu-sata-phy"; |
| 377 |
reg = <0x84000 0x0334>; |
| 378 |
clocks = <&gate_clk 15>; |
| 379 |
clock-names = "sata"; |
| 380 |
#phy-cells = <0>; |
| 381 |
status = "okay"; |
| 382 |
}; |
| 383 |
|
| 384 |
audio0: audio-controller@a0000 { |
| 385 |
compatible = "marvell,kirkwood-audio"; |
| 386 |
#sound-dai-cells = <0>; |
| 387 |
reg = <0xa0000 0x2210>; |
| 388 |
interrupts = <24>; |
| 389 |
clocks = <&gate_clk 9>; |
| 390 |
clock-names = "internal"; |
| 391 |
status = "disabled"; |
| 392 |
}; |
| 393 |
}; |
| 394 |
}; |