| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Device Tree file for CRS328-4C-20S-4S+ board |
| 4 |
* |
| 5 |
* Copyright (C) 2016 Allied Telesis Labs |
| 6 |
* Copyright (C) 2020 Sartura Ltd. |
| 7 |
* |
| 8 |
* Based on armada-xp-db.dts |
| 9 |
* |
| 10 |
* Note: this Device Tree assumes that the bootloader has remapped the |
| 11 |
* internal registers to 0xf1000000 (instead of the default |
| 12 |
* 0xd0000000). The 0xf1000000 is the default used by the recent, |
| 13 |
* DT-capable, U-Boot bootloaders provided by Marvell. Some earlier |
| 14 |
* boards were delivered with an older version of the bootloader that |
| 15 |
* left internal registers mapped at 0xd0000000. If you are in this |
| 16 |
* situation, you should either update your bootloader (preferred |
| 17 |
* solution) or the below Device Tree should be adjusted. |
| 18 |
*/ |
| 19 |
|
| 20 |
/dts-v1/; |
| 21 |
#include "armada-xp-98dx3236.dtsi" |
| 22 |
|
| 23 |
/ { |
| 24 |
model = "CRS328-4C-20S-4S+"; |
| 25 |
compatible = "mikrotik,crs328-4c-20s-4s", "marvell,armadaxp-98dx3236", "marvell,armada-370-xp"; |
| 26 |
|
| 27 |
chosen { |
| 28 |
bootargs = "console=ttyS0,115200 earlyprintk"; |
| 29 |
}; |
| 30 |
|
| 31 |
memory { |
| 32 |
device_type = "memory"; |
| 33 |
reg = <0 0x00000000 0 0x20000000>; /* 512 MB */ |
| 34 |
}; |
| 35 |
}; |
| 36 |
|
| 37 |
&L2 { |
| 38 |
arm,parity-enable; |
| 39 |
marvell,ecc-enable; |
| 40 |
}; |
| 41 |
|
| 42 |
&devbus_bootcs { |
| 43 |
status = "okay"; |
| 44 |
|
| 45 |
/* Device Bus parameters are required */ |
| 46 |
|
| 47 |
/* Read parameters */ |
| 48 |
devbus,bus-width = <16>; |
| 49 |
devbus,turn-off-ps = <60000>; |
| 50 |
devbus,badr-skew-ps = <0>; |
| 51 |
devbus,acc-first-ps = <124000>; |
| 52 |
devbus,acc-next-ps = <248000>; |
| 53 |
devbus,rd-setup-ps = <0>; |
| 54 |
devbus,rd-hold-ps = <0>; |
| 55 |
|
| 56 |
/* Write parameters */ |
| 57 |
devbus,sync-enable = <0>; |
| 58 |
devbus,wr-high-ps = <60000>; |
| 59 |
devbus,wr-low-ps = <60000>; |
| 60 |
devbus,ale-wr-ps = <60000>; |
| 61 |
}; |
| 62 |
|
| 63 |
&uart0 { |
| 64 |
status = "okay"; |
| 65 |
}; |
| 66 |
|
| 67 |
&uart1 { |
| 68 |
status = "okay"; |
| 69 |
}; |
| 70 |
|
| 71 |
&i2c0 { |
| 72 |
clock-frequency = <100000>; |
| 73 |
status = "okay"; |
| 74 |
}; |
| 75 |
|
| 76 |
&usb0 { |
| 77 |
status = "okay"; |
| 78 |
}; |
| 79 |
|
| 80 |
&spi0 { |
| 81 |
status = "okay"; |
| 82 |
|
| 83 |
flash@0 { |
| 84 |
#address-cells = <1>; |
| 85 |
#size-cells = <1>; |
| 86 |
compatible = "jedec,spi-nor"; |
| 87 |
reg = <0>; /* Chip select 0 */ |
| 88 |
spi-max-frequency = <108000000>; |
| 89 |
m25p,fast-read; |
| 90 |
|
| 91 |
partition@u-boot { |
| 92 |
reg = <0x00000000 0x001f0000>; |
| 93 |
label = "u-boot"; |
| 94 |
}; |
| 95 |
partition@u-boot-env { |
| 96 |
reg = <0x001f0000 0x00010000>; |
| 97 |
label = "u-boot-env"; |
| 98 |
}; |
| 99 |
partition@ubi1 { |
| 100 |
reg = <0x00200000 0x00e00000>; |
| 101 |
label = "ubi1"; |
| 102 |
}; |
| 103 |
}; |
| 104 |
}; |