| 1 |
// SPDX-License-Identifier: (GPL-2.0 OR MIT) |
| 2 |
/* |
| 3 |
* Device Tree file for Clearfog GTR machines rev 1.0 (88F6825) |
| 4 |
* |
| 5 |
* Rabeeh Khoury <[email protected]>, based on Russell King clearfog work |
| 6 |
*/ |
| 7 |
|
| 8 |
/* |
| 9 |
SERDES mapping - |
| 10 |
0. SATA1 on CON18, or optionally mini PCIe CON3 - PCIe0 |
| 11 |
1. 6141 switch (2.5Gbps capable) |
| 12 |
2. SATA0 on CON17, or optionally mini PCIe CON4 - PCIe1 |
| 13 |
3. USB 3.0 Host |
| 14 |
4. mini PCIe CON2 - PCIe2 |
| 15 |
5. SFP connector, or optionally SGMII Ethernet 1512 PHY |
| 16 |
|
| 17 |
USB 2.0 mapping - |
| 18 |
0. USB 2.0 - 0 USB pins header CON12 |
| 19 |
1. USB 2.0 - 1 mini PCIe CON2 |
| 20 |
2. USB 2.0 - 2 to USB 3.0 connector (used with SERDES #3) |
| 21 |
|
| 22 |
Pin mapping - |
| 23 |
0,1 - console UART |
| 24 |
2,3 - I2C0 - connected to I2C EEPROM, two temperature sensors, |
| 25 |
front panel and PSE controller |
| 26 |
4,5 - MDC/MDIO |
| 27 |
6..17 - RGMII |
| 28 |
18 - Topaz switch reset (active low) |
| 29 |
19 - 1512 phy reset |
| 30 |
20 - 1512 phy reset (eth2, optional) |
| 31 |
21,28,37,38,39,40 - SD0 |
| 32 |
22 - USB 3.0 current limiter enable (active high) |
| 33 |
24 - SFP TX fault (input active high) |
| 34 |
25 - SFP present (input active low) |
| 35 |
26,27 - I2C1 - connected to SFP |
| 36 |
29 - Fan PWM |
| 37 |
30 - CON4 mini PCIe wifi disable |
| 38 |
31 - CON3 mini PCIe wifi disable |
| 39 |
32 - Fuse programming power toggle (1.8v) |
| 40 |
33 - CON4 mini PCIe reset |
| 41 |
34 - CON2 mini PCIe wifi disable |
| 42 |
35 - CON3 mini PCIe reset |
| 43 |
36 - Rear button (GPIO active low) |
| 44 |
41 - CON1 front panel connector |
| 45 |
42 - Front LED1, or front panel CON1 |
| 46 |
43 - Micron L-PBGA 24 ball SPI (1Gb) CS, or TPM SPI CS |
| 47 |
44 - CON2 mini PCIe reset |
| 48 |
45 - TPM PIRQ signal, or front panel CON1 |
| 49 |
46 - SFP TX disable |
| 50 |
47 - Control isolation of boot sensitive SAR signals |
| 51 |
48 - PSE reset |
| 52 |
49 - PSE OSS signal |
| 53 |
50 - PSE interrupt |
| 54 |
52 - Front LED2, or front panel |
| 55 |
53 - Front button |
| 56 |
54 - SFP LOS (input active high) |
| 57 |
55 - Fan sense |
| 58 |
56(mosi),57(clk),58(miso) - SPI interface - 32Mb SPI, 1Gb SPI and TPM |
| 59 |
59 - SPI 32Mb W25Q32BVZPIG CS0 chip select (bootable) |
| 60 |
*/ |
| 61 |
|
| 62 |
/dts-v1/; |
| 63 |
#include <dt-bindings/input/input.h> |
| 64 |
#include <dt-bindings/gpio/gpio.h> |
| 65 |
#include <dt-bindings/leds/common.h> |
| 66 |
#include "armada-385.dtsi" |
| 67 |
|
| 68 |
/ { |
| 69 |
compatible = "marvell,armada385", "marvell,armada380"; |
| 70 |
|
| 71 |
aliases { |
| 72 |
/* So that mvebu u-boot can update the MAC addresses */ |
| 73 |
ethernet1 = ð0; |
| 74 |
ethernet2 = ð1; |
| 75 |
ethernet3 = ð2; |
| 76 |
i2c0 = &i2c0; |
| 77 |
i2c1 = &i2c1; |
| 78 |
}; |
| 79 |
|
| 80 |
chosen { |
| 81 |
stdout-path = "serial0:115200n8"; |
| 82 |
}; |
| 83 |
|
| 84 |
memory { |
| 85 |
device_type = "memory"; |
| 86 |
reg = <0x00000000 0x10000000>; /* 256 MB */ |
| 87 |
}; |
| 88 |
|
| 89 |
reg_3p3v: regulator-3p3v { |
| 90 |
compatible = "regulator-fixed"; |
| 91 |
regulator-name = "3P3V"; |
| 92 |
regulator-min-microvolt = <3300000>; |
| 93 |
regulator-max-microvolt = <3300000>; |
| 94 |
regulator-always-on; |
| 95 |
}; |
| 96 |
|
| 97 |
reg_5p0v: regulator-5p0v { |
| 98 |
compatible = "regulator-fixed"; |
| 99 |
regulator-name = "5P0V"; |
| 100 |
regulator-min-microvolt = <5000000>; |
| 101 |
regulator-max-microvolt = <5000000>; |
| 102 |
regulator-always-on; |
| 103 |
}; |
| 104 |
|
| 105 |
v_usb3_con: regulator-v-usb3-con { |
| 106 |
compatible = "regulator-fixed"; |
| 107 |
gpio = <&gpio0 22 GPIO_ACTIVE_LOW>; |
| 108 |
pinctrl-names = "default"; |
| 109 |
pinctrl-0 = <&cf_gtr_usb3_con_vbus>; |
| 110 |
regulator-max-microvolt = <5000000>; |
| 111 |
regulator-min-microvolt = <5000000>; |
| 112 |
regulator-name = "v_usb3_con"; |
| 113 |
vin-supply = <®_5p0v>; |
| 114 |
regulator-boot-on; |
| 115 |
regulator-always-on; |
| 116 |
}; |
| 117 |
|
| 118 |
soc { |
| 119 |
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 |
| 120 |
MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000 |
| 121 |
MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000 |
| 122 |
MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000 |
| 123 |
MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>; |
| 124 |
|
| 125 |
internal-regs { |
| 126 |
|
| 127 |
rtc@a3800 { |
| 128 |
status = "okay"; |
| 129 |
}; |
| 130 |
|
| 131 |
i2c@11000 { /* ROM, temp sensor and front panel */ |
| 132 |
pinctrl-0 = <&i2c0_pins>; |
| 133 |
pinctrl-names = "default"; |
| 134 |
status = "okay"; |
| 135 |
}; |
| 136 |
|
| 137 |
i2c@11100 { /* SFP (CON5/CON6) */ |
| 138 |
pinctrl-0 = <&cf_gtr_i2c1_pins>; |
| 139 |
pinctrl-names = "default"; |
| 140 |
status = "okay"; |
| 141 |
}; |
| 142 |
|
| 143 |
pinctrl@18000 { |
| 144 |
cf_gtr_fan_pwm: cf-gtr-fan-pwm { |
| 145 |
marvell,pins = "mpp23"; |
| 146 |
marvell,function = "gpio"; |
| 147 |
}; |
| 148 |
|
| 149 |
cf_gtr_front_button_pins: cf-gtr-front-button-pins { |
| 150 |
marvell,pins = "mpp53"; |
| 151 |
marvell,function = "gpio"; |
| 152 |
}; |
| 153 |
|
| 154 |
cf_gtr_i2c1_pins: i2c1-pins { |
| 155 |
/* SFP */ |
| 156 |
marvell,pins = "mpp26", "mpp27"; |
| 157 |
marvell,function = "i2c1"; |
| 158 |
}; |
| 159 |
|
| 160 |
cf_gtr_isolation_pins: cf-gtr-isolation-pins { |
| 161 |
marvell,pins = "mpp47"; |
| 162 |
marvell,function = "gpio"; |
| 163 |
}; |
| 164 |
|
| 165 |
cf_gtr_led_pins: led-pins { |
| 166 |
marvell,pins = "mpp42", "mpp52"; |
| 167 |
marvell,function = "gpio"; |
| 168 |
}; |
| 169 |
|
| 170 |
cf_gtr_lte_disable_pins: lte-disable-pins { |
| 171 |
marvell,pins = "mpp34"; |
| 172 |
marvell,function = "gpio"; |
| 173 |
}; |
| 174 |
|
| 175 |
cf_gtr_pci_pins: pci-pins { |
| 176 |
// pci reset |
| 177 |
marvell,pins = "mpp33", "mpp35", "mpp44"; |
| 178 |
marvell,function = "gpio"; |
| 179 |
}; |
| 180 |
|
| 181 |
cf_gtr_poe_reset_pins: cf-gtr-poe-reset-pins { |
| 182 |
marvell,pins = "mpp48"; |
| 183 |
marvell,function = "gpio"; |
| 184 |
}; |
| 185 |
|
| 186 |
cf_gtr_rear_button_pins: cf-gtr-rear-button-pins { |
| 187 |
marvell,pins = "mpp36"; |
| 188 |
marvell,function = "gpio"; |
| 189 |
}; |
| 190 |
|
| 191 |
cf_gtr_sdhci_pins: cf-gtr-sdhci-pins { |
| 192 |
marvell,pins = "mpp21", "mpp28", |
| 193 |
"mpp37", "mpp38", |
| 194 |
"mpp39", "mpp40"; |
| 195 |
marvell,function = "sd0"; |
| 196 |
}; |
| 197 |
|
| 198 |
cf_gtr_sfp0_pins: sfp0-pins { |
| 199 |
/* sfp modabs, txdisable */ |
| 200 |
marvell,pins = "mpp25", "mpp46"; |
| 201 |
marvell,function = "gpio"; |
| 202 |
}; |
| 203 |
|
| 204 |
cf_gtr_sfp1_pins: sfp1-pins { |
| 205 |
/* sfp modabs, txdisable */ |
| 206 |
marvell,pins = "mpp24", "mpp54"; |
| 207 |
marvell,function = "gpio"; |
| 208 |
}; |
| 209 |
|
| 210 |
cf_gtr_spi1_cs_pins: spi1-cs-pins { |
| 211 |
marvell,pins = "mpp59"; |
| 212 |
marvell,function = "spi1"; |
| 213 |
}; |
| 214 |
|
| 215 |
cf_gtr_switch_reset_pins: cf-gtr-switch-reset-pins { |
| 216 |
marvell,pins = "mpp18"; |
| 217 |
marvell,function = "gpio"; |
| 218 |
}; |
| 219 |
|
| 220 |
cf_gtr_usb3_con_vbus: cf-gtr-usb3-con-vbus { |
| 221 |
marvell,pins = "mpp22"; |
| 222 |
marvell,function = "gpio"; |
| 223 |
}; |
| 224 |
|
| 225 |
cf_gtr_wifi_disable_pins: wifi-disable-pins { |
| 226 |
marvell,pins = "mpp30", "mpp31"; |
| 227 |
marvell,function = "gpio"; |
| 228 |
}; |
| 229 |
}; |
| 230 |
|
| 231 |
sdhci@d8000 { |
| 232 |
bus-width = <4>; |
| 233 |
no-1-8-v; |
| 234 |
non-removable; |
| 235 |
pinctrl-0 = <&cf_gtr_sdhci_pins>; |
| 236 |
pinctrl-names = "default"; |
| 237 |
status = "okay"; |
| 238 |
vmmc = <®_3p3v>; |
| 239 |
wp-inverted; |
| 240 |
}; |
| 241 |
|
| 242 |
usb@58000 { |
| 243 |
status = "okay"; |
| 244 |
}; |
| 245 |
|
| 246 |
usb3@f0000 { |
| 247 |
status = "okay"; |
| 248 |
}; |
| 249 |
|
| 250 |
usb3@f8000 { |
| 251 |
vbus-supply = <&v_usb3_con>; |
| 252 |
status = "okay"; |
| 253 |
}; |
| 254 |
}; |
| 255 |
|
| 256 |
pcie { |
| 257 |
pinctrl-0 = <&cf_gtr_pci_pins>; |
| 258 |
pinctrl-names = "default"; |
| 259 |
status = "okay"; |
| 260 |
/* |
| 261 |
* The PCIe units are accessible through |
| 262 |
* the mini-PCIe connectors on the board. |
| 263 |
*/ |
| 264 |
/* CON3 - serdes 0 */ |
| 265 |
pcie@1,0 { |
| 266 |
reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; |
| 267 |
status = "okay"; |
| 268 |
}; |
| 269 |
|
| 270 |
/* CON4 - serdes 2 */ |
| 271 |
pcie@2,0 { |
| 272 |
reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; |
| 273 |
status = "okay"; |
| 274 |
}; |
| 275 |
|
| 276 |
/* CON2 - serdes 4 */ |
| 277 |
pcie@3,0 { |
| 278 |
reset-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; |
| 279 |
status = "okay"; |
| 280 |
}; |
| 281 |
}; |
| 282 |
}; |
| 283 |
|
| 284 |
/* CON5 */ |
| 285 |
sfp0: sfp-0 { |
| 286 |
compatible = "sff,sfp"; |
| 287 |
pinctrl-0 = <&cf_gtr_sfp0_pins>; |
| 288 |
pinctrl-names = "default"; |
| 289 |
i2c-bus = <&i2c1>; |
| 290 |
mod-def0-gpio = <&gpio0 25 GPIO_ACTIVE_LOW>; |
| 291 |
tx-disable-gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>; |
| 292 |
}; |
| 293 |
|
| 294 |
gpio-keys { |
| 295 |
compatible = "gpio-keys"; |
| 296 |
pinctrl-0 = <&cf_gtr_rear_button_pins &cf_gtr_front_button_pins>; |
| 297 |
pinctrl-names = "default"; |
| 298 |
|
| 299 |
button-0 { |
| 300 |
label = "Rear Button"; |
| 301 |
gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; |
| 302 |
linux,can-disable; |
| 303 |
linux,code = <BTN_0>; |
| 304 |
}; |
| 305 |
|
| 306 |
button-1 { |
| 307 |
label = "Front Button"; |
| 308 |
gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; |
| 309 |
linux,can-disable; |
| 310 |
linux,code = <BTN_1>; |
| 311 |
}; |
| 312 |
}; |
| 313 |
|
| 314 |
gpio-leds { |
| 315 |
compatible = "gpio-leds"; |
| 316 |
pinctrl-0 = <&cf_gtr_led_pins>; |
| 317 |
pinctrl-names = "default"; |
| 318 |
|
| 319 |
led1 { |
| 320 |
function = LED_FUNCTION_CPU; |
| 321 |
color = <LED_COLOR_ID_GREEN>; |
| 322 |
gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; |
| 323 |
}; |
| 324 |
|
| 325 |
led2 { |
| 326 |
function = LED_FUNCTION_HEARTBEAT; |
| 327 |
color = <LED_COLOR_ID_GREEN>; |
| 328 |
gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>; |
| 329 |
}; |
| 330 |
}; |
| 331 |
}; |
| 332 |
|
| 333 |
&bm { |
| 334 |
status = "okay"; |
| 335 |
}; |
| 336 |
|
| 337 |
&bm_bppi { |
| 338 |
status = "okay"; |
| 339 |
}; |
| 340 |
|
| 341 |
ð0 { |
| 342 |
/* ethernet@70000 */ |
| 343 |
pinctrl-0 = <&ge0_rgmii_pins>; |
| 344 |
pinctrl-names = "default"; |
| 345 |
phy = <&phy_dedicated>; |
| 346 |
phy-mode = "rgmii-id"; |
| 347 |
buffer-manager = <&bm>; |
| 348 |
bm,pool-long = <0>; |
| 349 |
bm,pool-short = <1>; |
| 350 |
status = "okay"; |
| 351 |
}; |
| 352 |
|
| 353 |
ð1 { |
| 354 |
/* ethernet@30000 */ |
| 355 |
bm,pool-long = <2>; |
| 356 |
bm,pool-short = <1>; |
| 357 |
buffer-manager = <&bm>; |
| 358 |
phys = <&comphy1 1>; |
| 359 |
phy-mode = "2500base-x"; |
| 360 |
status = "okay"; |
| 361 |
|
| 362 |
fixed-link { |
| 363 |
speed = <2500>; |
| 364 |
full-duplex; |
| 365 |
}; |
| 366 |
}; |
| 367 |
|
| 368 |
ð2 { |
| 369 |
/* ethernet@34000 */ |
| 370 |
bm,pool-long = <3>; |
| 371 |
bm,pool-short = <1>; |
| 372 |
buffer-manager = <&bm>; |
| 373 |
managed = "in-band-status"; |
| 374 |
phys = <&comphy5 1>; |
| 375 |
phy-mode = "sgmii"; |
| 376 |
sfp = <&sfp0>; |
| 377 |
status = "okay"; |
| 378 |
}; |
| 379 |
|
| 380 |
&mdio { |
| 381 |
pinctrl-names = "default"; |
| 382 |
pinctrl-0 = <&mdio_pins>; |
| 383 |
status = "okay"; |
| 384 |
|
| 385 |
phy_dedicated: ethernet-phy@0 { |
| 386 |
/* |
| 387 |
* Annoyingly, the marvell phy driver configures the LED |
| 388 |
* register, rather than preserving reset-loaded setting. |
| 389 |
* We undo that rubbish here. |
| 390 |
*/ |
| 391 |
marvell,reg-init = <3 16 0 0x1017>; |
| 392 |
reg = <0>; |
| 393 |
}; |
| 394 |
}; |
| 395 |
|
| 396 |
&uart0 { |
| 397 |
pinctrl-0 = <&uart0_pins>; |
| 398 |
pinctrl-names = "default"; |
| 399 |
status = "okay"; |
| 400 |
}; |
| 401 |
|
| 402 |
&spi1 { |
| 403 |
/* |
| 404 |
* CS0: W25Q32 flash |
| 405 |
*/ |
| 406 |
pinctrl-0 = <&spi1_pins &cf_gtr_spi1_cs_pins>; |
| 407 |
pinctrl-names = "default"; |
| 408 |
status = "okay"; |
| 409 |
|
| 410 |
flash@0 { |
| 411 |
#address-cells = <1>; |
| 412 |
#size-cells = <0>; |
| 413 |
compatible = "w25q32", "jedec,spi-nor"; |
| 414 |
reg = <0>; /* Chip select 0 */ |
| 415 |
spi-max-frequency = <3000000>; |
| 416 |
status = "okay"; |
| 417 |
}; |
| 418 |
}; |
| 419 |
|
| 420 |
&i2c0 { |
| 421 |
pinctrl-0 = <&i2c0_pins>; |
| 422 |
pinctrl-names = "default"; |
| 423 |
status = "okay"; |
| 424 |
|
| 425 |
/* U26 temperature sensor placed near SoC */ |
| 426 |
temp1: temperature-sensor@4c { |
| 427 |
compatible = "ti,tmp75c"; |
| 428 |
reg = <0x4c>; |
| 429 |
}; |
| 430 |
|
| 431 |
/* U27 temperature sensor placed near RTC battery */ |
| 432 |
temp2: temperature-sensor@4d { |
| 433 |
compatible = "ti,tmp75c"; |
| 434 |
reg = <0x4d>; |
| 435 |
}; |
| 436 |
|
| 437 |
/* 2Kb eeprom */ |
| 438 |
eeprom@53 { |
| 439 |
compatible = "atmel,24c02"; |
| 440 |
reg = <0x53>; |
| 441 |
}; |
| 442 |
}; |
| 443 |
|
| 444 |
&ahci0 { |
| 445 |
status = "okay"; |
| 446 |
}; |
| 447 |
|
| 448 |
&ahci1 { |
| 449 |
status = "okay"; |
| 450 |
}; |
| 451 |
|
| 452 |
&gpio0 { |
| 453 |
pinctrl-0 = <&cf_gtr_fan_pwm &cf_gtr_wifi_disable_pins>; |
| 454 |
pinctrl-names = "default"; |
| 455 |
|
| 456 |
wifi-disable-hog { |
| 457 |
gpio-hog; |
| 458 |
gpios = <30 GPIO_ACTIVE_LOW>, <31 GPIO_ACTIVE_LOW>; |
| 459 |
output-low; |
| 460 |
line-name = "wifi-disable"; |
| 461 |
}; |
| 462 |
}; |
| 463 |
|
| 464 |
&gpio1 { |
| 465 |
pinctrl-0 = <&cf_gtr_isolation_pins &cf_gtr_poe_reset_pins &cf_gtr_lte_disable_pins>; |
| 466 |
pinctrl-names = "default"; |
| 467 |
|
| 468 |
lte-disable-hog { |
| 469 |
gpio-hog; |
| 470 |
gpios = <2 GPIO_ACTIVE_LOW>; |
| 471 |
output-low; |
| 472 |
line-name = "lte-disable"; |
| 473 |
}; |
| 474 |
|
| 475 |
/* |
| 476 |
* This signal, when asserted, isolates Armada 38x sample at reset pins |
| 477 |
* from control of external devices. Should be de-asserted after reset. |
| 478 |
*/ |
| 479 |
sar-isolation-hog { |
| 480 |
gpio-hog; |
| 481 |
gpios = <15 GPIO_ACTIVE_LOW>; |
| 482 |
output-low; |
| 483 |
line-name = "sar-isolation"; |
| 484 |
}; |
| 485 |
|
| 486 |
poe-reset-hog { |
| 487 |
gpio-hog; |
| 488 |
gpios = <16 GPIO_ACTIVE_LOW>; |
| 489 |
output-low; |
| 490 |
line-name = "poe-reset"; |
| 491 |
}; |
| 492 |
}; |