| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Device Tree file for Marvell RD-AXPWiFiAP. |
| 4 |
* |
| 5 |
* Note: this board is shipped with a new generation boot loader that |
| 6 |
* remaps internal registers at 0xf1000000. Therefore, if earlyprintk |
| 7 |
* is used, the CONFIG_DEBUG_MVEBU_UART0_ALTERNATE option or the |
| 8 |
* CONFIG_DEBUG_MVEBU_UART1_ALTERNATE option should be used. |
| 9 |
* |
| 10 |
* Copyright (C) 2013 Marvell |
| 11 |
* |
| 12 |
* Thomas Petazzoni <[email protected]> |
| 13 |
*/ |
| 14 |
|
| 15 |
/dts-v1/; |
| 16 |
#include <dt-bindings/gpio/gpio.h> |
| 17 |
#include <dt-bindings/input/input.h> |
| 18 |
#include "armada-xp-mv78230.dtsi" |
| 19 |
|
| 20 |
/ { |
| 21 |
model = "Marvell RD-AXPWiFiAP"; |
| 22 |
compatible = "marvell,rd-axpwifiap", "marvell,armadaxp-mv78230", "marvell,armadaxp", "marvell,armada-370-xp"; |
| 23 |
|
| 24 |
chosen { |
| 25 |
stdout-path = "serial0:115200n8"; |
| 26 |
}; |
| 27 |
|
| 28 |
memory@0 { |
| 29 |
device_type = "memory"; |
| 30 |
reg = <0x00000000 0x00000000 0x00000000 0x40000000>; /* 1GB */ |
| 31 |
}; |
| 32 |
|
| 33 |
soc { |
| 34 |
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 |
| 35 |
MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 |
| 36 |
MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000 |
| 37 |
MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000>; |
| 38 |
|
| 39 |
internal-regs { |
| 40 |
/* UART0 */ |
| 41 |
serial@12000 { |
| 42 |
status = "okay"; |
| 43 |
}; |
| 44 |
|
| 45 |
/* UART1 */ |
| 46 |
serial@12100 { |
| 47 |
status = "okay"; |
| 48 |
}; |
| 49 |
|
| 50 |
sata@a0000 { |
| 51 |
nr-ports = <1>; |
| 52 |
status = "okay"; |
| 53 |
}; |
| 54 |
|
| 55 |
ethernet@70000 { |
| 56 |
pinctrl-0 = <&ge0_rgmii_pins>; |
| 57 |
pinctrl-names = "default"; |
| 58 |
status = "okay"; |
| 59 |
phy = <&phy0>; |
| 60 |
phy-mode = "rgmii-id"; |
| 61 |
}; |
| 62 |
ethernet@74000 { |
| 63 |
pinctrl-0 = <&ge1_rgmii_pins>; |
| 64 |
pinctrl-names = "default"; |
| 65 |
status = "okay"; |
| 66 |
phy = <&phy1>; |
| 67 |
phy-mode = "rgmii-id"; |
| 68 |
}; |
| 69 |
}; |
| 70 |
}; |
| 71 |
|
| 72 |
gpio-keys { |
| 73 |
compatible = "gpio-keys"; |
| 74 |
pinctrl-0 = <&keys_pin>; |
| 75 |
pinctrl-names = "default"; |
| 76 |
|
| 77 |
button-reset { |
| 78 |
label = "Factory Reset Button"; |
| 79 |
linux,code = <KEY_SETUP>; |
| 80 |
gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; |
| 81 |
}; |
| 82 |
}; |
| 83 |
}; |
| 84 |
|
| 85 |
&mdio { |
| 86 |
phy0: ethernet-phy@0 { |
| 87 |
reg = <0>; |
| 88 |
}; |
| 89 |
|
| 90 |
phy1: ethernet-phy@1 { |
| 91 |
reg = <1>; |
| 92 |
}; |
| 93 |
}; |
| 94 |
|
| 95 |
&pciec { |
| 96 |
status = "okay"; |
| 97 |
|
| 98 |
/* First mini-PCIe port */ |
| 99 |
pcie@1,0 { |
| 100 |
/* Port 0, Lane 0 */ |
| 101 |
status = "okay"; |
| 102 |
}; |
| 103 |
|
| 104 |
/* Second mini-PCIe port */ |
| 105 |
pcie@2,0 { |
| 106 |
/* Port 0, Lane 1 */ |
| 107 |
status = "okay"; |
| 108 |
}; |
| 109 |
|
| 110 |
/* Renesas uPD720202 USB 3.0 controller */ |
| 111 |
pcie@3,0 { |
| 112 |
/* Port 0, Lane 3 */ |
| 113 |
status = "okay"; |
| 114 |
}; |
| 115 |
}; |
| 116 |
|
| 117 |
&pinctrl { |
| 118 |
pinctrl-0 = <&phy_int_pin>; |
| 119 |
pinctrl-names = "default"; |
| 120 |
|
| 121 |
keys_pin: keys-pin { |
| 122 |
marvell,pins = "mpp33"; |
| 123 |
marvell,function = "gpio"; |
| 124 |
}; |
| 125 |
|
| 126 |
phy_int_pin: phy-int-pin { |
| 127 |
marvell,pins = "mpp32"; |
| 128 |
marvell,function = "gpio"; |
| 129 |
}; |
| 130 |
}; |
| 131 |
|
| 132 |
&spi0 { |
| 133 |
status = "okay"; |
| 134 |
|
| 135 |
flash@0 { |
| 136 |
#address-cells = <1>; |
| 137 |
#size-cells = <1>; |
| 138 |
compatible = "n25q128a13", "jedec,spi-nor"; |
| 139 |
reg = <0>; /* Chip select 0 */ |
| 140 |
spi-max-frequency = <108000000>; |
| 141 |
}; |
| 142 |
}; |