| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Device Tree file for OpenBlocks AX3-4 board |
| 4 |
* |
| 5 |
* Copyright (C) 2012 Marvell |
| 6 |
* |
| 7 |
* Thomas Petazzoni <[email protected]> |
| 8 |
*/ |
| 9 |
|
| 10 |
/dts-v1/; |
| 11 |
#include <dt-bindings/gpio/gpio.h> |
| 12 |
#include <dt-bindings/input/input.h> |
| 13 |
#include "armada-xp-mv78260.dtsi" |
| 14 |
|
| 15 |
/ { |
| 16 |
model = "PlatHome OpenBlocks AX3-4 board"; |
| 17 |
compatible = "plathome,openblocks-ax3-4", "marvell,armadaxp-mv78260", "marvell,armadaxp", "marvell,armada-370-xp"; |
| 18 |
|
| 19 |
chosen { |
| 20 |
stdout-path = "serial0:115200n8"; |
| 21 |
}; |
| 22 |
|
| 23 |
memory@0 { |
| 24 |
device_type = "memory"; |
| 25 |
reg = <0 0x00000000 0 0x40000000>; /* 1 GB soldered on */ |
| 26 |
}; |
| 27 |
|
| 28 |
soc { |
| 29 |
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000 |
| 30 |
MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 |
| 31 |
MBUS_ID(0x01, 0x2f) 0 0 0xe8000000 0x8000000 |
| 32 |
MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000 |
| 33 |
MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000 |
| 34 |
MBUS_ID(0x0c, 0x04) 0 0 0xd1200000 0x100000>; |
| 35 |
|
| 36 |
devbus-bootcs { |
| 37 |
status = "okay"; |
| 38 |
|
| 39 |
/* Device Bus parameters are required */ |
| 40 |
|
| 41 |
/* Read parameters */ |
| 42 |
devbus,bus-width = <16>; |
| 43 |
devbus,turn-off-ps = <60000>; |
| 44 |
devbus,badr-skew-ps = <0>; |
| 45 |
devbus,acc-first-ps = <124000>; |
| 46 |
devbus,acc-next-ps = <248000>; |
| 47 |
devbus,rd-setup-ps = <0>; |
| 48 |
devbus,rd-hold-ps = <0>; |
| 49 |
|
| 50 |
/* Write parameters */ |
| 51 |
devbus,sync-enable = <0>; |
| 52 |
devbus,wr-high-ps = <60000>; |
| 53 |
devbus,wr-low-ps = <60000>; |
| 54 |
devbus,ale-wr-ps = <60000>; |
| 55 |
|
| 56 |
/* NOR 128 MiB */ |
| 57 |
nor@0 { |
| 58 |
compatible = "cfi-flash"; |
| 59 |
reg = <0 0x8000000>; |
| 60 |
bank-width = <2>; |
| 61 |
}; |
| 62 |
}; |
| 63 |
|
| 64 |
internal-regs { |
| 65 |
rtc@10300 { |
| 66 |
/* No crystal connected to the internal RTC */ |
| 67 |
status = "disabled"; |
| 68 |
}; |
| 69 |
serial@12000 { |
| 70 |
status = "okay"; |
| 71 |
}; |
| 72 |
serial@12100 { |
| 73 |
status = "okay"; |
| 74 |
}; |
| 75 |
|
| 76 |
leds { |
| 77 |
compatible = "gpio-leds"; |
| 78 |
pinctrl-names = "default"; |
| 79 |
pinctrl-0 = <&led_pins>; |
| 80 |
|
| 81 |
red_led { |
| 82 |
label = "red_led"; |
| 83 |
gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; |
| 84 |
default-state = "off"; |
| 85 |
}; |
| 86 |
|
| 87 |
yellow_led { |
| 88 |
label = "yellow_led"; |
| 89 |
gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; |
| 90 |
default-state = "off"; |
| 91 |
}; |
| 92 |
|
| 93 |
green_led { |
| 94 |
label = "green_led"; |
| 95 |
gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; |
| 96 |
default-state = "keep"; |
| 97 |
}; |
| 98 |
}; |
| 99 |
|
| 100 |
gpio-keys { |
| 101 |
compatible = "gpio-keys"; |
| 102 |
|
| 103 |
button-init { |
| 104 |
label = "Init Button"; |
| 105 |
linux,code = <KEY_POWER>; |
| 106 |
gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; |
| 107 |
}; |
| 108 |
}; |
| 109 |
|
| 110 |
ethernet@70000 { |
| 111 |
status = "okay"; |
| 112 |
phy = <&phy0>; |
| 113 |
phy-mode = "sgmii"; |
| 114 |
buffer-manager = <&bm>; |
| 115 |
bm,pool-long = <0>; |
| 116 |
}; |
| 117 |
ethernet@74000 { |
| 118 |
status = "okay"; |
| 119 |
phy = <&phy1>; |
| 120 |
phy-mode = "sgmii"; |
| 121 |
buffer-manager = <&bm>; |
| 122 |
bm,pool-long = <1>; |
| 123 |
}; |
| 124 |
ethernet@30000 { |
| 125 |
status = "okay"; |
| 126 |
phy = <&phy2>; |
| 127 |
phy-mode = "sgmii"; |
| 128 |
buffer-manager = <&bm>; |
| 129 |
bm,pool-long = <2>; |
| 130 |
}; |
| 131 |
ethernet@34000 { |
| 132 |
status = "okay"; |
| 133 |
phy = <&phy3>; |
| 134 |
phy-mode = "sgmii"; |
| 135 |
buffer-manager = <&bm>; |
| 136 |
bm,pool-long = <3>; |
| 137 |
}; |
| 138 |
i2c@11000 { |
| 139 |
status = "okay"; |
| 140 |
clock-frequency = <400000>; |
| 141 |
}; |
| 142 |
i2c@11100 { |
| 143 |
status = "okay"; |
| 144 |
clock-frequency = <400000>; |
| 145 |
|
| 146 |
s35390a: s35390a@30 { |
| 147 |
compatible = "s35390a"; |
| 148 |
reg = <0x30>; |
| 149 |
}; |
| 150 |
}; |
| 151 |
sata@a0000 { |
| 152 |
nr-ports = <2>; |
| 153 |
status = "okay"; |
| 154 |
}; |
| 155 |
|
| 156 |
/* Front side USB 0 */ |
| 157 |
usb@50000 { |
| 158 |
status = "okay"; |
| 159 |
}; |
| 160 |
|
| 161 |
/* Front side USB 1 */ |
| 162 |
usb@51000 { |
| 163 |
status = "okay"; |
| 164 |
}; |
| 165 |
|
| 166 |
bm@c0000 { |
| 167 |
status = "okay"; |
| 168 |
}; |
| 169 |
}; |
| 170 |
|
| 171 |
bm-bppi { |
| 172 |
status = "okay"; |
| 173 |
}; |
| 174 |
}; |
| 175 |
}; |
| 176 |
|
| 177 |
&pciec { |
| 178 |
status = "okay"; |
| 179 |
/* Internal mini-PCIe connector */ |
| 180 |
pcie@1,0 { |
| 181 |
/* Port 0, Lane 0 */ |
| 182 |
status = "okay"; |
| 183 |
}; |
| 184 |
}; |
| 185 |
|
| 186 |
&mdio { |
| 187 |
phy0: ethernet-phy@0 { |
| 188 |
reg = <0>; |
| 189 |
}; |
| 190 |
|
| 191 |
phy1: ethernet-phy@1 { |
| 192 |
reg = <1>; |
| 193 |
}; |
| 194 |
|
| 195 |
phy2: ethernet-phy@2 { |
| 196 |
reg = <2>; |
| 197 |
}; |
| 198 |
|
| 199 |
phy3: ethernet-phy@3 { |
| 200 |
reg = <3>; |
| 201 |
}; |
| 202 |
}; |
| 203 |
|
| 204 |
&pinctrl { |
| 205 |
led_pins: led-pins-0 { |
| 206 |
marvell,pins = "mpp49", "mpp51", "mpp53"; |
| 207 |
marvell,function = "gpio"; |
| 208 |
}; |
| 209 |
}; |