| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* sama5d3xmb.dts - Device Tree file for SAMA5D3x mother board |
| 4 |
* |
| 5 |
* Copyright (C) 2013 Atmel, |
| 6 |
* 2013 Ludovic Desroches <[email protected]> |
| 7 |
*/ |
| 8 |
#include "sama5d3xcm.dtsi" |
| 9 |
|
| 10 |
/ { |
| 11 |
compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5"; |
| 12 |
|
| 13 |
ahb { |
| 14 |
apb { |
| 15 |
mmc0: mmc@f0000000 { |
| 16 |
pinctrl-names = "default"; |
| 17 |
pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>; |
| 18 |
status = "okay"; |
| 19 |
slot@0 { |
| 20 |
reg = <0>; |
| 21 |
bus-width = <4>; |
| 22 |
cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>; |
| 23 |
}; |
| 24 |
}; |
| 25 |
|
| 26 |
spi0: spi@f0004000 { |
| 27 |
dmas = <0>, <0>; /* Do not use DMA for spi0 */ |
| 28 |
|
| 29 |
flash@0 { |
| 30 |
compatible = "atmel,at25df321a"; |
| 31 |
spi-max-frequency = <50000000>; |
| 32 |
reg = <0>; |
| 33 |
}; |
| 34 |
}; |
| 35 |
|
| 36 |
ssc0: ssc@f0008000 { |
| 37 |
atmel,clk-from-rk-pin; |
| 38 |
}; |
| 39 |
|
| 40 |
/* |
| 41 |
* i2c0 conflicts with ISI: |
| 42 |
* disable it to allow the use of ISI |
| 43 |
* can not enable audio when i2c0 disabled |
| 44 |
*/ |
| 45 |
i2c0: i2c@f0014000 { |
| 46 |
wm8904: wm8904@1a { |
| 47 |
compatible = "wlf,wm8904"; |
| 48 |
reg = <0x1a>; |
| 49 |
clocks = <&pmc PMC_TYPE_SYSTEM 8>; |
| 50 |
clock-names = "mclk"; |
| 51 |
}; |
| 52 |
}; |
| 53 |
|
| 54 |
i2c1: i2c@f0018000 { |
| 55 |
ov2640: camera@30 { |
| 56 |
compatible = "ovti,ov2640"; |
| 57 |
reg = <0x30>; |
| 58 |
pinctrl-names = "default"; |
| 59 |
pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; |
| 60 |
resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>; |
| 61 |
pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>; |
| 62 |
/* use pck1 for the master clock of ov2640 */ |
| 63 |
clocks = <&pmc PMC_TYPE_SYSTEM 9>; |
| 64 |
clock-names = "xvclk"; |
| 65 |
assigned-clocks = <&pmc PMC_TYPE_SYSTEM 9>; |
| 66 |
assigned-clock-rates = <25000000>; |
| 67 |
|
| 68 |
port { |
| 69 |
ov2640_0: endpoint { |
| 70 |
remote-endpoint = <&isi_0>; |
| 71 |
bus-width = <8>; |
| 72 |
}; |
| 73 |
}; |
| 74 |
}; |
| 75 |
}; |
| 76 |
|
| 77 |
usart1: serial@f0020000 { |
| 78 |
dmas = <0>, <0>; /* Do not use DMA for usart1 */ |
| 79 |
pinctrl-names = "default"; |
| 80 |
pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>; |
| 81 |
status = "okay"; |
| 82 |
}; |
| 83 |
|
| 84 |
isi: isi@f0034000 { |
| 85 |
port { |
| 86 |
isi_0: endpoint { |
| 87 |
remote-endpoint = <&ov2640_0>; |
| 88 |
bus-width = <8>; |
| 89 |
vsync-active = <1>; |
| 90 |
hsync-active = <1>; |
| 91 |
}; |
| 92 |
}; |
| 93 |
}; |
| 94 |
|
| 95 |
mmc1: mmc@f8000000 { |
| 96 |
pinctrl-names = "default"; |
| 97 |
pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>; |
| 98 |
status = "okay"; |
| 99 |
slot@0 { |
| 100 |
reg = <0>; |
| 101 |
bus-width = <4>; |
| 102 |
cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>; |
| 103 |
}; |
| 104 |
}; |
| 105 |
|
| 106 |
adc0: adc@f8018000 { |
| 107 |
pinctrl-names = "default"; |
| 108 |
pinctrl-0 = < |
| 109 |
&pinctrl_adc0_adtrg |
| 110 |
&pinctrl_adc0_ad0 |
| 111 |
&pinctrl_adc0_ad1 |
| 112 |
&pinctrl_adc0_ad2 |
| 113 |
&pinctrl_adc0_ad3 |
| 114 |
&pinctrl_adc0_ad4 |
| 115 |
>; |
| 116 |
status = "okay"; |
| 117 |
}; |
| 118 |
|
| 119 |
pinctrl@fffff200 { |
| 120 |
board { |
| 121 |
pinctrl_mmc0_cd: mmc0_cd { |
| 122 |
atmel,pins = |
| 123 |
<AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD17 GPIO with pullup deglitch */ |
| 124 |
}; |
| 125 |
|
| 126 |
pinctrl_mmc1_cd: mmc1_cd { |
| 127 |
atmel,pins = |
| 128 |
<AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD18 GPIO with pullup deglitch */ |
| 129 |
}; |
| 130 |
|
| 131 |
pinctrl_pck0_as_audio_mck: pck0_as_audio_mck { |
| 132 |
atmel,pins = |
| 133 |
<AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD30 periph B */ |
| 134 |
}; |
| 135 |
|
| 136 |
pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 { |
| 137 |
atmel,pins = |
| 138 |
<AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD31 periph B ISI_MCK */ |
| 139 |
}; |
| 140 |
|
| 141 |
pinctrl_sensor_reset: sensor_reset-0 { |
| 142 |
atmel,pins = |
| 143 |
<AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE24 gpio */ |
| 144 |
}; |
| 145 |
|
| 146 |
pinctrl_sensor_power: sensor_power-0 { |
| 147 |
atmel,pins = |
| 148 |
<AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */ |
| 149 |
}; |
| 150 |
|
| 151 |
pinctrl_usba_vbus: usba_vbus { |
| 152 |
atmel,pins = |
| 153 |
<AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PD29 GPIO with deglitch */ |
| 154 |
}; |
| 155 |
}; |
| 156 |
}; |
| 157 |
|
| 158 |
dbgu: serial@ffffee00 { |
| 159 |
dmas = <0>, <0>; /* Do not use DMA for dbgu */ |
| 160 |
status = "okay"; |
| 161 |
}; |
| 162 |
|
| 163 |
watchdog@fffffe40 { |
| 164 |
status = "okay"; |
| 165 |
}; |
| 166 |
}; |
| 167 |
|
| 168 |
usb0: gadget@500000 { |
| 169 |
atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>; |
| 170 |
pinctrl-names = "default"; |
| 171 |
pinctrl-0 = <&pinctrl_usba_vbus>; |
| 172 |
status = "okay"; |
| 173 |
}; |
| 174 |
|
| 175 |
usb1: usb@600000 { |
| 176 |
num-ports = <3>; |
| 177 |
atmel,vbus-gpio = <&pioD 25 GPIO_ACTIVE_HIGH |
| 178 |
&pioD 26 GPIO_ACTIVE_LOW |
| 179 |
&pioD 27 GPIO_ACTIVE_LOW |
| 180 |
>; |
| 181 |
status = "okay"; |
| 182 |
}; |
| 183 |
|
| 184 |
usb2: usb@700000 { |
| 185 |
status = "okay"; |
| 186 |
}; |
| 187 |
}; |
| 188 |
|
| 189 |
sound { |
| 190 |
compatible = "atmel,asoc-wm8904"; |
| 191 |
pinctrl-names = "default"; |
| 192 |
pinctrl-0 = <&pinctrl_pck0_as_audio_mck>; |
| 193 |
|
| 194 |
atmel,model = "wm8904 @ SAMA5D3EK"; |
| 195 |
atmel,audio-routing = |
| 196 |
"Headphone Jack", "HPOUTL", |
| 197 |
"Headphone Jack", "HPOUTR", |
| 198 |
"IN2L", "Line In Jack", |
| 199 |
"IN2R", "Line In Jack", |
| 200 |
"Mic", "MICBIAS", |
| 201 |
"IN1L", "Mic"; |
| 202 |
|
| 203 |
atmel,ssc-controller = <&ssc0>; |
| 204 |
atmel,audio-codec = <&wm8904>; |
| 205 |
|
| 206 |
status = "disabled"; |
| 207 |
}; |
| 208 |
}; |