| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* at91sam9261ek.dts - Device Tree file for Atmel at91sam9261 reference board |
| 4 |
* |
| 5 |
* Copyright (C) 2013 Jean-Jacques Hiblot <[email protected]> |
| 6 |
*/ |
| 7 |
/dts-v1/; |
| 8 |
#include "at91sam9261.dtsi" |
| 9 |
|
| 10 |
/ { |
| 11 |
model = "Atmel at91sam9261ek"; |
| 12 |
compatible = "atmel,at91sam9261ek", "atmel,at91sam9261", "atmel,at91sam9"; |
| 13 |
|
| 14 |
chosen { |
| 15 |
bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs rw"; |
| 16 |
stdout-path = "serial0:115200n8"; |
| 17 |
}; |
| 18 |
|
| 19 |
memory@20000000 { |
| 20 |
reg = <0x20000000 0x4000000>; |
| 21 |
}; |
| 22 |
|
| 23 |
clocks { |
| 24 |
slow_xtal { |
| 25 |
clock-frequency = <32768>; |
| 26 |
}; |
| 27 |
|
| 28 |
main_xtal { |
| 29 |
clock-frequency = <18432000>; |
| 30 |
}; |
| 31 |
}; |
| 32 |
|
| 33 |
ahb { |
| 34 |
usb0: usb@500000 { |
| 35 |
status = "okay"; |
| 36 |
}; |
| 37 |
|
| 38 |
fb0: fb@600000 { |
| 39 |
display = <&display0>; |
| 40 |
atmel,power-control-gpio = <&pioA 12 GPIO_ACTIVE_LOW>; |
| 41 |
status = "okay"; |
| 42 |
|
| 43 |
display0: panel { |
| 44 |
bits-per-pixel = <16>; |
| 45 |
atmel,lcdcon-backlight; |
| 46 |
atmel,dmacon = <0x1>; |
| 47 |
atmel,lcdcon2 = <0x80008002>; |
| 48 |
atmel,guard-time = <1>; |
| 49 |
atmel,lcd-wiring-mode = "BRG"; |
| 50 |
|
| 51 |
display-timings { |
| 52 |
native-mode = <&timing0>; |
| 53 |
timing0: timing0 { |
| 54 |
clock-frequency = <4965000>; |
| 55 |
hactive = <240>; |
| 56 |
vactive = <320>; |
| 57 |
hback-porch = <1>; |
| 58 |
hfront-porch = <33>; |
| 59 |
vback-porch = <1>; |
| 60 |
vfront-porch = <0>; |
| 61 |
hsync-len = <5>; |
| 62 |
vsync-len = <1>; |
| 63 |
hsync-active = <1>; |
| 64 |
vsync-active = <1>; |
| 65 |
}; |
| 66 |
}; |
| 67 |
}; |
| 68 |
}; |
| 69 |
|
| 70 |
ebi: ebi@10000000 { |
| 71 |
status = "okay"; |
| 72 |
|
| 73 |
nand_controller: nand-controller { |
| 74 |
status = "okay"; |
| 75 |
pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>; |
| 76 |
pinctrl-names = "default"; |
| 77 |
|
| 78 |
nand@3 { |
| 79 |
reg = <0x3 0x0 0x800000>; |
| 80 |
rb-gpios = <&pioC 15 GPIO_ACTIVE_HIGH>; |
| 81 |
cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>; |
| 82 |
nand-bus-width = <8>; |
| 83 |
nand-ecc-mode = "soft"; |
| 84 |
nand-on-flash-bbt; |
| 85 |
label = "atmel_nand"; |
| 86 |
|
| 87 |
partitions { |
| 88 |
compatible = "fixed-partitions"; |
| 89 |
#address-cells = <1>; |
| 90 |
#size-cells = <1>; |
| 91 |
|
| 92 |
at91bootstrap@0 { |
| 93 |
label = "at91bootstrap"; |
| 94 |
reg = <0x0 0x40000>; |
| 95 |
}; |
| 96 |
|
| 97 |
bootloader@40000 { |
| 98 |
label = "bootloader"; |
| 99 |
reg = <0x40000 0x80000>; |
| 100 |
}; |
| 101 |
|
| 102 |
bootloaderenv@c0000 { |
| 103 |
label = "bootloader env"; |
| 104 |
reg = <0xc0000 0xc0000>; |
| 105 |
}; |
| 106 |
|
| 107 |
dtb@180000 { |
| 108 |
label = "device tree"; |
| 109 |
reg = <0x180000 0x80000>; |
| 110 |
}; |
| 111 |
|
| 112 |
kernel@200000 { |
| 113 |
label = "kernel"; |
| 114 |
reg = <0x200000 0x600000>; |
| 115 |
}; |
| 116 |
|
| 117 |
rootfs@800000 { |
| 118 |
label = "rootfs"; |
| 119 |
reg = <0x800000 0x0f800000>; |
| 120 |
}; |
| 121 |
}; |
| 122 |
}; |
| 123 |
}; |
| 124 |
}; |
| 125 |
|
| 126 |
apb { |
| 127 |
tcb0: timer@fffa0000 { |
| 128 |
timer0: timer@0 { |
| 129 |
compatible = "atmel,tcb-timer"; |
| 130 |
reg = <0>, <1>; |
| 131 |
}; |
| 132 |
|
| 133 |
timer1: timer@2 { |
| 134 |
compatible = "atmel,tcb-timer"; |
| 135 |
reg = <2>; |
| 136 |
}; |
| 137 |
}; |
| 138 |
|
| 139 |
usb1: gadget@fffa4000 { |
| 140 |
atmel,vbus-gpio = <&pioB 29 GPIO_ACTIVE_HIGH>; |
| 141 |
status = "okay"; |
| 142 |
}; |
| 143 |
|
| 144 |
spi0: spi@fffc8000 { |
| 145 |
cs-gpios = <&pioA 3 0>, <0>, <&pioA 28 0>, <0>; |
| 146 |
status = "okay"; |
| 147 |
|
| 148 |
flash@0 { |
| 149 |
compatible = "atmel,at45", "atmel,dataflash"; |
| 150 |
reg = <0>; |
| 151 |
spi-max-frequency = <15000000>; |
| 152 |
}; |
| 153 |
|
| 154 |
tsc2046@2 { |
| 155 |
reg = <2>; |
| 156 |
compatible = "ti,ads7843"; |
| 157 |
interrupts-extended = <&pioC 2 IRQ_TYPE_EDGE_BOTH>; |
| 158 |
spi-max-frequency = <3000000>; |
| 159 |
pendown-gpio = <&pioC 2 GPIO_ACTIVE_LOW>; |
| 160 |
|
| 161 |
ti,x-min = /bits/ 16 <150>; |
| 162 |
ti,x-max = /bits/ 16 <3830>; |
| 163 |
ti,y-min = /bits/ 16 <190>; |
| 164 |
ti,y-max = /bits/ 16 <3830>; |
| 165 |
ti,vref-delay-usecs = /bits/ 16 <450>; |
| 166 |
ti,x-plate-ohms = /bits/ 16 <450>; |
| 167 |
ti,y-plate-ohms = /bits/ 16 <250>; |
| 168 |
ti,pressure-max = /bits/ 16 <15000>; |
| 169 |
ti,debounce-rep = /bits/ 16 <0>; |
| 170 |
ti,debounce-tol = /bits/ 16 <65535>; |
| 171 |
ti,debounce-max = /bits/ 16 <1>; |
| 172 |
|
| 173 |
wakeup-source; |
| 174 |
}; |
| 175 |
}; |
| 176 |
|
| 177 |
dbgu: serial@fffff200 { |
| 178 |
status = "okay"; |
| 179 |
}; |
| 180 |
|
| 181 |
rtc@fffffd20 { |
| 182 |
atmel,rtt-rtc-time-reg = <&gpbr 0x0>; |
| 183 |
}; |
| 184 |
|
| 185 |
watchdog@fffffd40 { |
| 186 |
status = "okay"; |
| 187 |
}; |
| 188 |
|
| 189 |
}; |
| 190 |
}; |
| 191 |
|
| 192 |
leds { |
| 193 |
compatible = "gpio-leds"; |
| 194 |
|
| 195 |
led-ds8 { |
| 196 |
label = "ds8"; |
| 197 |
gpios = <&pioA 13 GPIO_ACTIVE_LOW>; |
| 198 |
linux,default-trigger = "none"; |
| 199 |
}; |
| 200 |
|
| 201 |
led-ds7 { |
| 202 |
label = "ds7"; |
| 203 |
gpios = <&pioA 14 GPIO_ACTIVE_LOW>; |
| 204 |
linux,default-trigger = "nand-disk"; |
| 205 |
}; |
| 206 |
|
| 207 |
led-ds1 { |
| 208 |
label = "ds1"; |
| 209 |
gpios = <&pioA 23 GPIO_ACTIVE_LOW>; |
| 210 |
linux,default-trigger = "heartbeat"; |
| 211 |
}; |
| 212 |
}; |
| 213 |
|
| 214 |
gpio-keys { |
| 215 |
compatible = "gpio-keys"; |
| 216 |
|
| 217 |
button-0 { |
| 218 |
label = "button_0"; |
| 219 |
gpios = <&pioA 27 GPIO_ACTIVE_LOW>; |
| 220 |
linux,code = <256>; |
| 221 |
wakeup-source; |
| 222 |
}; |
| 223 |
|
| 224 |
button-1 { |
| 225 |
label = "button_1"; |
| 226 |
gpios = <&pioA 26 GPIO_ACTIVE_LOW>; |
| 227 |
linux,code = <257>; |
| 228 |
wakeup-source; |
| 229 |
}; |
| 230 |
|
| 231 |
button-2 { |
| 232 |
label = "button_2"; |
| 233 |
gpios = <&pioA 25 GPIO_ACTIVE_LOW>; |
| 234 |
linux,code = <258>; |
| 235 |
wakeup-source; |
| 236 |
}; |
| 237 |
|
| 238 |
button-3 { |
| 239 |
label = "button_3"; |
| 240 |
gpios = <&pioA 24 GPIO_ACTIVE_LOW>; |
| 241 |
linux,code = <259>; |
| 242 |
wakeup-source; |
| 243 |
}; |
| 244 |
}; |
| 245 |
}; |