| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* at91sam9n12ek.dts - Device Tree file for AT91SAM9N12-EK board |
| 4 |
* |
| 5 |
* Copyright (C) 2012 Atmel, |
| 6 |
* 2012 Hong Xu <[email protected]> |
| 7 |
*/ |
| 8 |
/dts-v1/; |
| 9 |
#include "at91sam9n12.dtsi" |
| 10 |
|
| 11 |
/ { |
| 12 |
model = "Atmel AT91SAM9N12-EK"; |
| 13 |
compatible = "atmel,at91sam9n12ek", "atmel,at91sam9n12", "atmel,at91sam9"; |
| 14 |
|
| 15 |
chosen { |
| 16 |
bootargs = "root=/dev/mtdblock1 rw rootfstype=jffs2"; |
| 17 |
stdout-path = "serial0:115200n8"; |
| 18 |
}; |
| 19 |
|
| 20 |
memory@20000000 { |
| 21 |
reg = <0x20000000 0x8000000>; |
| 22 |
}; |
| 23 |
|
| 24 |
clocks { |
| 25 |
slow_xtal { |
| 26 |
clock-frequency = <32768>; |
| 27 |
}; |
| 28 |
|
| 29 |
main_xtal { |
| 30 |
clock-frequency = <16000000>; |
| 31 |
}; |
| 32 |
}; |
| 33 |
|
| 34 |
ahb { |
| 35 |
apb { |
| 36 |
dbgu: serial@fffff200 { |
| 37 |
status = "okay"; |
| 38 |
}; |
| 39 |
|
| 40 |
ssc0: ssc@f0010000 { |
| 41 |
status = "okay"; |
| 42 |
}; |
| 43 |
|
| 44 |
tcb0: timer@f8008000 { |
| 45 |
timer@0 { |
| 46 |
compatible = "atmel,tcb-timer"; |
| 47 |
reg = <0>; |
| 48 |
}; |
| 49 |
|
| 50 |
timer@1 { |
| 51 |
compatible = "atmel,tcb-timer"; |
| 52 |
reg = <1>; |
| 53 |
}; |
| 54 |
}; |
| 55 |
|
| 56 |
i2c0: i2c@f8010000 { |
| 57 |
status = "okay"; |
| 58 |
|
| 59 |
wm8904: codec@1a { |
| 60 |
compatible = "wlf,wm8904"; |
| 61 |
reg = <0x1a>; |
| 62 |
clocks = <&pmc PMC_TYPE_SYSTEM 8>; |
| 63 |
clock-names = "mclk"; |
| 64 |
}; |
| 65 |
|
| 66 |
qt1070: keyboard@1b { |
| 67 |
compatible = "qt1070"; |
| 68 |
reg = <0x1b>; |
| 69 |
interrupt-parent = <&pioA>; |
| 70 |
interrupts = <2 IRQ_TYPE_EDGE_FALLING>; |
| 71 |
pinctrl-names = "default"; |
| 72 |
pinctrl-0 = <&pinctrl_qt1070_irq>; |
| 73 |
}; |
| 74 |
}; |
| 75 |
|
| 76 |
mmc0: mmc@f0008000 { |
| 77 |
pinctrl-0 = < |
| 78 |
&pinctrl_board_mmc0 |
| 79 |
&pinctrl_mmc0_slot0_clk_cmd_dat0 |
| 80 |
&pinctrl_mmc0_slot0_dat1_3>; |
| 81 |
status = "okay"; |
| 82 |
slot@0 { |
| 83 |
reg = <0>; |
| 84 |
bus-width = <4>; |
| 85 |
cd-gpios = <&pioA 7 GPIO_ACTIVE_HIGH>; |
| 86 |
}; |
| 87 |
}; |
| 88 |
|
| 89 |
pinctrl@fffff400 { |
| 90 |
mmc0 { |
| 91 |
pinctrl_board_mmc0: mmc0-board { |
| 92 |
atmel,pins = |
| 93 |
<AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PA7 gpio CD pin pull up and deglitch */ |
| 94 |
}; |
| 95 |
}; |
| 96 |
|
| 97 |
qt1070 { |
| 98 |
pinctrl_qt1070_irq: qt1070_irq { |
| 99 |
atmel,pins = |
| 100 |
<AT91_PIOA 2 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; |
| 101 |
}; |
| 102 |
}; |
| 103 |
|
| 104 |
sound { |
| 105 |
pinctrl_pck0_as_audio_mck: pck0_as_audio_mck { |
| 106 |
atmel,pins = |
| 107 |
<AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| 108 |
}; |
| 109 |
}; |
| 110 |
|
| 111 |
usb1 { |
| 112 |
pinctrl_usb1_vbus_sense: usb1_vbus_sense { |
| 113 |
atmel,pins = |
| 114 |
<AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PB16 gpio usb vbus sense, no pull up and deglitch */ |
| 115 |
}; |
| 116 |
}; |
| 117 |
}; |
| 118 |
|
| 119 |
spi0: spi@f0000000 { |
| 120 |
status = "okay"; |
| 121 |
cs-gpios = <&pioA 14 0>, <0>, <0>, <0>; |
| 122 |
flash@0 { |
| 123 |
compatible = "atmel,at25df321a"; |
| 124 |
spi-max-frequency = <50000000>; |
| 125 |
reg = <0>; |
| 126 |
}; |
| 127 |
}; |
| 128 |
|
| 129 |
hlcdc: hlcdc@f8038000 { |
| 130 |
status = "okay"; |
| 131 |
|
| 132 |
hlcdc-display-controller { |
| 133 |
pinctrl-names = "default"; |
| 134 |
pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>; |
| 135 |
|
| 136 |
port@0 { |
| 137 |
hlcdc_panel_output: endpoint@0 { |
| 138 |
reg = <0>; |
| 139 |
remote-endpoint = <&panel_input>; |
| 140 |
}; |
| 141 |
}; |
| 142 |
}; |
| 143 |
}; |
| 144 |
|
| 145 |
usb1: gadget@f803c000 { |
| 146 |
pinctrl-names = "default"; |
| 147 |
pinctrl-0 = <&pinctrl_usb1_vbus_sense>; |
| 148 |
atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>; |
| 149 |
status = "okay"; |
| 150 |
}; |
| 151 |
|
| 152 |
watchdog@fffffe40 { |
| 153 |
status = "okay"; |
| 154 |
}; |
| 155 |
|
| 156 |
rtc@fffffeb0 { |
| 157 |
status = "okay"; |
| 158 |
}; |
| 159 |
}; |
| 160 |
|
| 161 |
ebi: ebi@10000000 { |
| 162 |
status = "okay"; |
| 163 |
|
| 164 |
nand_controller: nand-controller { |
| 165 |
status = "okay"; |
| 166 |
pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>; |
| 167 |
pinctrl-names = "default"; |
| 168 |
|
| 169 |
nand@3 { |
| 170 |
reg = <0x3 0x0 0x800000>; |
| 171 |
rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>; |
| 172 |
cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>; |
| 173 |
nand-bus-width = <8>; |
| 174 |
nand-ecc-mode = "soft"; |
| 175 |
nand-ecc-strength = <2>; |
| 176 |
nand-ecc-step-size = <512>; |
| 177 |
nand-on-flash-bbt; |
| 178 |
label = "atmel_nand"; |
| 179 |
}; |
| 180 |
}; |
| 181 |
}; |
| 182 |
|
| 183 |
usb0: usb@500000 { |
| 184 |
num-ports = <1>; |
| 185 |
atmel,vbus-gpio = <&pioB 7 GPIO_ACTIVE_LOW>; |
| 186 |
status = "okay"; |
| 187 |
}; |
| 188 |
}; |
| 189 |
|
| 190 |
backlight: backlight { |
| 191 |
compatible = "pwm-backlight"; |
| 192 |
pwms = <&hlcdc_pwm 0 50000 0>; |
| 193 |
brightness-levels = <0 4 8 16 32 64 128 255>; |
| 194 |
default-brightness-level = <6>; |
| 195 |
power-supply = <&bl_reg>; |
| 196 |
status = "okay"; |
| 197 |
}; |
| 198 |
|
| 199 |
bl_reg: backlight_regulator { |
| 200 |
compatible = "regulator-fixed"; |
| 201 |
regulator-name = "backlight-power-supply"; |
| 202 |
regulator-min-microvolt = <5000000>; |
| 203 |
regulator-max-microvolt = <5000000>; |
| 204 |
status = "okay"; |
| 205 |
}; |
| 206 |
|
| 207 |
leds { |
| 208 |
compatible = "gpio-leds"; |
| 209 |
|
| 210 |
led-d8 { |
| 211 |
label = "d8"; |
| 212 |
gpios = <&pioB 4 GPIO_ACTIVE_LOW>; |
| 213 |
linux,default-trigger = "mmc0"; |
| 214 |
}; |
| 215 |
|
| 216 |
led-d9 { |
| 217 |
label = "d9"; |
| 218 |
gpios = <&pioB 5 GPIO_ACTIVE_LOW>; |
| 219 |
linux,default-trigger = "nand-disk"; |
| 220 |
}; |
| 221 |
|
| 222 |
led-d10 { |
| 223 |
label = "d10"; |
| 224 |
gpios = <&pioB 6 GPIO_ACTIVE_HIGH>; |
| 225 |
linux,default-trigger = "heartbeat"; |
| 226 |
}; |
| 227 |
}; |
| 228 |
|
| 229 |
gpio-keys { |
| 230 |
compatible = "gpio-keys"; |
| 231 |
|
| 232 |
button-enter { |
| 233 |
label = "Enter"; |
| 234 |
gpios = <&pioB 3 GPIO_ACTIVE_LOW>; |
| 235 |
linux,code = <28>; |
| 236 |
wakeup-source; |
| 237 |
}; |
| 238 |
}; |
| 239 |
|
| 240 |
panel: panel { |
| 241 |
compatible = "qiaodian,qd43003c0-40"; |
| 242 |
backlight = <&backlight>; |
| 243 |
power-supply = <&panel_reg>; |
| 244 |
#address-cells = <1>; |
| 245 |
#size-cells = <0>; |
| 246 |
status = "okay"; |
| 247 |
|
| 248 |
port@0 { |
| 249 |
reg = <0>; |
| 250 |
#address-cells = <1>; |
| 251 |
#size-cells = <0>; |
| 252 |
|
| 253 |
panel_input: endpoint@0 { |
| 254 |
reg = <0>; |
| 255 |
remote-endpoint = <&hlcdc_panel_output>; |
| 256 |
}; |
| 257 |
}; |
| 258 |
}; |
| 259 |
|
| 260 |
panel_reg: panel_regulator { |
| 261 |
compatible = "regulator-fixed"; |
| 262 |
regulator-name = "panel-power-supply"; |
| 263 |
regulator-min-microvolt = <3300000>; |
| 264 |
regulator-max-microvolt = <3300000>; |
| 265 |
status = "okay"; |
| 266 |
}; |
| 267 |
|
| 268 |
sound { |
| 269 |
compatible = "atmel,asoc-wm8904"; |
| 270 |
pinctrl-names = "default"; |
| 271 |
pinctrl-0 = <&pinctrl_pck0_as_audio_mck>; |
| 272 |
|
| 273 |
atmel,model = "wm8904 @ AT91SAM9N12"; |
| 274 |
atmel,audio-routing = |
| 275 |
"Headphone Jack", "HPOUTL", |
| 276 |
"Headphone Jack", "HPOUTR", |
| 277 |
"IN2L", "Line In Jack", |
| 278 |
"IN2R", "Line In Jack", |
| 279 |
"Mic", "MICBIAS", |
| 280 |
"IN1L", "Mic"; |
| 281 |
|
| 282 |
atmel,ssc-controller = <&ssc0>; |
| 283 |
atmel,audio-codec = <&wm8904>; |
| 284 |
}; |
| 285 |
}; |