| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* at91-ariag25.dts - Device Tree file for Acme Systems Aria G25 (AT91SAM9G25 based) |
| 4 |
* |
| 5 |
* Copyright (C) 2013 Douglas Gilbert <[email protected]>, |
| 6 |
* Robert Nelson <[email protected]> |
| 7 |
*/ |
| 8 |
/dts-v1/; |
| 9 |
#include "at91sam9g25.dtsi" |
| 10 |
|
| 11 |
/ { |
| 12 |
model = "Acme Systems Aria G25"; |
| 13 |
compatible = "acme,ariag25", "atmel,at91sam9x5ek", |
| 14 |
"atmel,at91sam9x5", "atmel,at91sam9"; |
| 15 |
|
| 16 |
aliases { |
| 17 |
serial5 = &uart0; |
| 18 |
serial6 = &uart1; |
| 19 |
}; |
| 20 |
|
| 21 |
chosen { |
| 22 |
bootargs = "console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait"; |
| 23 |
}; |
| 24 |
|
| 25 |
memory@20000000 { |
| 26 |
/* 128 MB, change this for 256 MB revision */ |
| 27 |
reg = <0x20000000 0x8000000>; |
| 28 |
}; |
| 29 |
|
| 30 |
clocks { |
| 31 |
slow_xtal { |
| 32 |
clock-frequency = <32768>; |
| 33 |
}; |
| 34 |
|
| 35 |
main_xtal { |
| 36 |
clock-frequency = <12000000>; |
| 37 |
}; |
| 38 |
}; |
| 39 |
|
| 40 |
leds { |
| 41 |
compatible = "gpio-leds"; |
| 42 |
|
| 43 |
/* little green LED in middle of Aria G25 module */ |
| 44 |
aria_led { |
| 45 |
label = "aria_led"; |
| 46 |
gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */ |
| 47 |
linux,default-trigger = "heartbeat"; |
| 48 |
}; |
| 49 |
|
| 50 |
}; |
| 51 |
|
| 52 |
onewire { |
| 53 |
compatible = "w1-gpio"; |
| 54 |
gpios = <&pioA 21 GPIO_ACTIVE_LOW>; |
| 55 |
pinctrl-names = "default"; |
| 56 |
pinctrl-0 = <&pinctrl_w1_0>; |
| 57 |
}; |
| 58 |
}; |
| 59 |
|
| 60 |
&adc0 { |
| 61 |
status = "okay"; |
| 62 |
atmel,adc-channels-used = <0xf>; |
| 63 |
}; |
| 64 |
|
| 65 |
&dbgu { |
| 66 |
status = "okay"; |
| 67 |
}; |
| 68 |
|
| 69 |
&i2c0 { |
| 70 |
status = "okay"; |
| 71 |
}; |
| 72 |
|
| 73 |
&i2c1 { |
| 74 |
status = "okay"; |
| 75 |
}; |
| 76 |
|
| 77 |
/* TWD2+TCLK2 hidden behind ethernet, so no i2c2 */ |
| 78 |
|
| 79 |
&macb0 { |
| 80 |
phy-mode = "rmii"; |
| 81 |
/* |
| 82 |
* following can be overwritten by bootloader: |
| 83 |
* for example u-boot 'ftd set' command |
| 84 |
*/ |
| 85 |
local-mac-address = [00 00 00 00 00 00]; |
| 86 |
status = "okay"; |
| 87 |
}; |
| 88 |
|
| 89 |
|
| 90 |
&mmc0 { |
| 91 |
/* N.B. Aria has no SD card detect (CD), assumed present */ |
| 92 |
|
| 93 |
pinctrl-0 = < |
| 94 |
&pinctrl_mmc0_slot0_clk_cmd_dat0 |
| 95 |
&pinctrl_mmc0_slot0_dat1_3>; |
| 96 |
pinctrl-names = "default"; |
| 97 |
status = "okay"; |
| 98 |
|
| 99 |
slot@0 { |
| 100 |
reg = <0>; |
| 101 |
bus-width = <4>; |
| 102 |
}; |
| 103 |
}; |
| 104 |
|
| 105 |
&pinctrl { |
| 106 |
w1_0 { |
| 107 |
pinctrl_w1_0: w1_0-0 { |
| 108 |
atmel,pins = <0 21 0x0 0x1>; /* PA21 PIO, pull-up */ |
| 109 |
}; |
| 110 |
}; |
| 111 |
}; |
| 112 |
|
| 113 |
&rtc { |
| 114 |
status = "okay"; |
| 115 |
}; |
| 116 |
|
| 117 |
&tcb0 { |
| 118 |
timer@0 { |
| 119 |
compatible = "atmel,tcb-timer"; |
| 120 |
reg = <0>; |
| 121 |
}; |
| 122 |
|
| 123 |
timer@1 { |
| 124 |
compatible = "atmel,tcb-timer"; |
| 125 |
reg = <1>; |
| 126 |
}; |
| 127 |
}; |
| 128 |
|
| 129 |
/* |
| 130 |
* UART0/1 pins are marked as GPIO on |
| 131 |
* Aria documentation. |
| 132 |
* Change to "okay" if you need additional serial ports |
| 133 |
*/ |
| 134 |
&uart0 { |
| 135 |
status = "disabled"; |
| 136 |
}; |
| 137 |
|
| 138 |
&uart1 { |
| 139 |
status = "disabled"; |
| 140 |
}; |
| 141 |
|
| 142 |
&usart0 { |
| 143 |
pinctrl-0 = <&pinctrl_usart0 |
| 144 |
&pinctrl_usart0_rts |
| 145 |
&pinctrl_usart0_cts>; |
| 146 |
status = "okay"; |
| 147 |
}; |
| 148 |
|
| 149 |
&usart1 { |
| 150 |
pinctrl-0 = <&pinctrl_usart1 |
| 151 |
/* &pinctrl_usart1_rts */ |
| 152 |
/* &pinctrl_usart1_cts */ |
| 153 |
>; |
| 154 |
status = "okay"; |
| 155 |
}; |
| 156 |
|
| 157 |
&usart2 { |
| 158 |
/* cannot activate RTS2+CTS2, clash with |
| 159 |
* ethernet on PB0 and PB1 */ |
| 160 |
pinctrl-0 = <&pinctrl_usart2>; |
| 161 |
status = "okay"; |
| 162 |
}; |
| 163 |
|
| 164 |
&usart3 { |
| 165 |
compatible = "atmel,at91sam9260-usart"; |
| 166 |
reg = <0xf8028000 0x200>; |
| 167 |
interrupts = <8 4 5>; |
| 168 |
pinctrl-names = "default"; |
| 169 |
pinctrl-0 = <&pinctrl_usart3 |
| 170 |
/* &pinctrl_usart3_rts */ |
| 171 |
/* &pinctrl_usart3_cts */ |
| 172 |
>; |
| 173 |
status = "okay"; |
| 174 |
}; |
| 175 |
|
| 176 |
&usb0 { |
| 177 |
status = "okay"; |
| 178 |
num-ports = <3>; |
| 179 |
}; |
| 180 |
|
| 181 |
&usb1 { |
| 182 |
status = "okay"; |
| 183 |
}; |