| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* at91-kizboxmini.dts - Device Tree file for Overkiz Kizbox mini board |
| 4 |
* |
| 5 |
* Copyright (C) 2014-2018 Overkiz SAS |
| 6 |
* Author: Antoine Aubert <[email protected]> |
| 7 |
* Gaël Portay <[email protected]> |
| 8 |
* Kévin Raymond <[email protected]> |
| 9 |
* Dorian Rocipon <[email protected]> |
| 10 |
*/ |
| 11 |
#include "at91sam9g25.dtsi" |
| 12 |
|
| 13 |
/ { |
| 14 |
chosen { |
| 15 |
bootargs = "ubi.mtd=ubi"; |
| 16 |
stdout-path = &dbgu; |
| 17 |
}; |
| 18 |
|
| 19 |
memory@20000000 { |
| 20 |
reg = <0x20000000 0x8000000>; |
| 21 |
}; |
| 22 |
|
| 23 |
clocks { |
| 24 |
main_xtal { |
| 25 |
clock-frequency = <12000000>; |
| 26 |
}; |
| 27 |
|
| 28 |
slow_xtal { |
| 29 |
clock-frequency = <32768>; |
| 30 |
}; |
| 31 |
|
| 32 |
adc_op_clk { |
| 33 |
status = "disabled"; |
| 34 |
}; |
| 35 |
}; |
| 36 |
|
| 37 |
gpio_keys { |
| 38 |
compatible = "gpio-keys"; |
| 39 |
|
| 40 |
key-prog { |
| 41 |
label = "PB_PROG"; |
| 42 |
gpios = <&pioC 17 GPIO_ACTIVE_LOW>; |
| 43 |
linux,code = <0x102>; |
| 44 |
wakeup-source; |
| 45 |
}; |
| 46 |
|
| 47 |
key-reset { |
| 48 |
label = "PB_RST"; |
| 49 |
gpios = <&pioC 16 GPIO_ACTIVE_LOW>; |
| 50 |
linux,code = <0x100>; |
| 51 |
wakeup-source; |
| 52 |
}; |
| 53 |
}; |
| 54 |
|
| 55 |
leds: led-controller-1 { |
| 56 |
compatible = "pwm-leds"; |
| 57 |
|
| 58 |
led_blue: led-1 { |
| 59 |
label = "pwm:blue:user"; |
| 60 |
pwms = <&pwm0 2 10000000 0>; |
| 61 |
max-brightness = <255>; |
| 62 |
linux,default-trigger = "none"; |
| 63 |
status = "disabled"; |
| 64 |
}; |
| 65 |
|
| 66 |
led_green: led-2 { |
| 67 |
label = "pwm:green:user"; |
| 68 |
pwms = <&pwm0 0 10000000 0>; |
| 69 |
max-brightness = <255>; |
| 70 |
linux,default-trigger = "default-on"; |
| 71 |
}; |
| 72 |
|
| 73 |
led_red: led-3 { |
| 74 |
label = "pwm:red:user"; |
| 75 |
pwms = <&pwm0 1 10000000 0>; |
| 76 |
max-brightness = <255>; |
| 77 |
linux,default-trigger = "default-on"; |
| 78 |
}; |
| 79 |
}; |
| 80 |
}; |
| 81 |
|
| 82 |
&usart0 { |
| 83 |
atmel,use-dma-rx; |
| 84 |
atmel,use-dma-tx; |
| 85 |
status = "okay"; |
| 86 |
}; |
| 87 |
|
| 88 |
&macb0 { |
| 89 |
phy-mode = "rmii"; |
| 90 |
status = "okay"; |
| 91 |
}; |
| 92 |
|
| 93 |
&pwm0 { |
| 94 |
pinctrl-names = "default"; |
| 95 |
pinctrl-0 = <&pinctrl_pwm0_pwm0_1 |
| 96 |
&pinctrl_pwm0_pwm1_1 |
| 97 |
&pinctrl_pwm0_pwm2_1>; |
| 98 |
status = "okay"; |
| 99 |
}; |
| 100 |
|
| 101 |
&dbgu { |
| 102 |
status = "okay"; |
| 103 |
}; |
| 104 |
|
| 105 |
&watchdog { |
| 106 |
status = "okay"; |
| 107 |
}; |
| 108 |
|
| 109 |
&adc0 { |
| 110 |
status = "disabled"; |
| 111 |
}; |
| 112 |
|
| 113 |
&rtc { |
| 114 |
status = "disabled"; |
| 115 |
}; |
| 116 |
|
| 117 |
&ebi { |
| 118 |
pinctrl-0 = <&pinctrl_ebi_addr_nand |
| 119 |
&pinctrl_ebi_data_0_7>; |
| 120 |
pinctrl-names = "default"; |
| 121 |
status = "okay"; |
| 122 |
}; |
| 123 |
|
| 124 |
&nand_controller { |
| 125 |
status = "okay"; |
| 126 |
pinctrl-0 = <&pinctrl_nand_oe_we |
| 127 |
&pinctrl_nand_cs |
| 128 |
&pinctrl_nand_rb>; |
| 129 |
pinctrl-names = "default"; |
| 130 |
|
| 131 |
nand@3 { |
| 132 |
reg = <0x3 0x0 0x800000>; |
| 133 |
rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>; |
| 134 |
cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>; |
| 135 |
nand-bus-width = <8>; |
| 136 |
nand-ecc-mode = "hw"; |
| 137 |
nand-ecc-strength = <4>; |
| 138 |
nand-ecc-step-size = <512>; |
| 139 |
nand-on-flash-bbt; |
| 140 |
label = "atmel_nand"; |
| 141 |
|
| 142 |
partitions { |
| 143 |
compatible = "fixed-partitions"; |
| 144 |
#address-cells = <1>; |
| 145 |
#size-cells = <1>; |
| 146 |
|
| 147 |
bootstrap@0 { |
| 148 |
label = "bootstrap"; |
| 149 |
reg = <0x0 0x20000>; |
| 150 |
}; |
| 151 |
|
| 152 |
ubi@20000 { |
| 153 |
label = "ubi"; |
| 154 |
reg = <0x20000 0x7fe0000>; |
| 155 |
}; |
| 156 |
}; |
| 157 |
}; |
| 158 |
}; |
| 159 |
|
| 160 |
&usb0 { |
| 161 |
num-ports = <1>; |
| 162 |
status = "okay"; |
| 163 |
}; |
| 164 |
|
| 165 |
&usb1 { |
| 166 |
status = "okay"; |
| 167 |
}; |
| 168 |
|