| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* at91-wb50n.dtsi - Device Tree include file for wb50n cpu module |
| 4 |
* |
| 5 |
* Copyright (C) 2018 Laird |
| 6 |
* |
| 7 |
*/ |
| 8 |
|
| 9 |
#include "sama5d31.dtsi" |
| 10 |
|
| 11 |
/ { |
| 12 |
model = "Laird Workgroup Bridge 50N - Atmel SAMA5D"; |
| 13 |
compatible = "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5"; |
| 14 |
|
| 15 |
chosen { |
| 16 |
bootargs = "ubi.mtd=6 root=ubi0:rootfs rootfstype=ubifs rw"; |
| 17 |
stdout-path = "serial0:115200n8"; |
| 18 |
}; |
| 19 |
|
| 20 |
memory@20000000 { |
| 21 |
reg = <0x20000000 0x4000000>; |
| 22 |
}; |
| 23 |
}; |
| 24 |
|
| 25 |
&pinctrl { |
| 26 |
board { |
| 27 |
pinctrl_mmc0_cd: mmc0_cd { |
| 28 |
atmel,pins = <AT91_PIOC 26 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PC26 GPIO with pullup deglitch */ |
| 29 |
}; |
| 30 |
|
| 31 |
pinctrl_usba_vbus: usba_vbus { |
| 32 |
atmel,pins = <AT91_PIOB 13 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PB13 GPIO with deglitch */ |
| 33 |
}; |
| 34 |
}; |
| 35 |
}; |
| 36 |
|
| 37 |
&slow_xtal { |
| 38 |
clock-frequency = <32768>; |
| 39 |
}; |
| 40 |
|
| 41 |
&main_xtal { |
| 42 |
clock-frequency = <12000000>; |
| 43 |
}; |
| 44 |
|
| 45 |
&clk32k { |
| 46 |
atmel,osc-bypass; |
| 47 |
}; |
| 48 |
|
| 49 |
&mmc0 { |
| 50 |
pinctrl-names = "default"; |
| 51 |
pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>; |
| 52 |
cd-gpios = <&pioC 26 GPIO_ACTIVE_LOW>; |
| 53 |
slot@0 { |
| 54 |
reg = <0>; |
| 55 |
bus-width = <4>; |
| 56 |
}; |
| 57 |
}; |
| 58 |
|
| 59 |
&mmc1 { |
| 60 |
pinctrl-names = "default"; |
| 61 |
pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>; |
| 62 |
status = "okay"; |
| 63 |
atheros@0 { |
| 64 |
compatible = "atheros,ath6kl"; |
| 65 |
atheros,board-id = "SD32"; |
| 66 |
reg = <0>; |
| 67 |
bus-width = <4>; |
| 68 |
}; |
| 69 |
}; |
| 70 |
|
| 71 |
&macb1 { |
| 72 |
phy-mode = "rmii"; |
| 73 |
}; |
| 74 |
|
| 75 |
&dbgu { |
| 76 |
dmas = <0>, <0>; /* Do not use DMA for dbgu */ |
| 77 |
}; |
| 78 |
|
| 79 |
/* On BB40 this port is labeled UART1 */ |
| 80 |
&usart0 { |
| 81 |
atmel,use-dma-rx; |
| 82 |
atmel,use-dma-tx; |
| 83 |
pinctrl-names = "default"; |
| 84 |
pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts_cts>; |
| 85 |
}; |
| 86 |
|
| 87 |
/* On BB40 this port is labeled UART0 */ |
| 88 |
&usart1 { |
| 89 |
atmel,use-dma-rx; |
| 90 |
atmel,use-dma-tx; |
| 91 |
pinctrl-names = "default"; |
| 92 |
pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>; |
| 93 |
dtr-gpios = <&pioD 13 GPIO_ACTIVE_LOW>; |
| 94 |
dsr-gpios = <&pioD 11 GPIO_ACTIVE_LOW>; |
| 95 |
dcd-gpios = <&pioD 7 GPIO_ACTIVE_LOW>; |
| 96 |
rng-gpios = <&pioD 8 GPIO_ACTIVE_LOW>; |
| 97 |
}; |
| 98 |
|
| 99 |
/* USART3 is direct-connect to the Bluetooth UART on the radio SIP */ |
| 100 |
&usart3 { |
| 101 |
atmel,use-dma-rx; |
| 102 |
atmel,use-dma-tx; |
| 103 |
pinctrl-names = "default"; |
| 104 |
pinctrl-0 = <&pinctrl_usart3 &pinctrl_usart3_rts_cts>; |
| 105 |
status = "okay"; |
| 106 |
}; |
| 107 |
|
| 108 |
&spi1 { |
| 109 |
cs-gpios = <&pioC 25 0>, <0>, <0>, <0>; |
| 110 |
}; |
| 111 |
|
| 112 |
&ebi { |
| 113 |
pinctrl-0 = <&pinctrl_ebi_nand_addr>; |
| 114 |
pinctrl-names = "default"; |
| 115 |
status = "okay"; |
| 116 |
}; |
| 117 |
|
| 118 |
&nand_controller { |
| 119 |
status = "okay"; |
| 120 |
|
| 121 |
nand: nand@3 { |
| 122 |
reg = <0x3 0x0 0x2>; |
| 123 |
atmel,rb = <0>; |
| 124 |
nand-bus-width = <8>; |
| 125 |
nand-ecc-mode = "hw"; |
| 126 |
nand-ecc-strength = <8>; |
| 127 |
nand-ecc-step-size = <512>; |
| 128 |
nand-on-flash-bbt; |
| 129 |
label = "atmel_nand"; |
| 130 |
|
| 131 |
partitions { |
| 132 |
compatible = "fixed-partitions"; |
| 133 |
#address-cells = <1>; |
| 134 |
#size-cells = <1>; |
| 135 |
|
| 136 |
at91bootstrap@0 { |
| 137 |
label = "at91bs"; |
| 138 |
reg = <0x0 0x20000>; |
| 139 |
}; |
| 140 |
|
| 141 |
uboot@20000 { |
| 142 |
label = "u-boot"; |
| 143 |
reg = <0x20000 0x80000>; |
| 144 |
}; |
| 145 |
|
| 146 |
ubootenv@a0000 { |
| 147 |
label = "u-boot-env"; |
| 148 |
reg = <0xa0000 0x20000>; |
| 149 |
}; |
| 150 |
|
| 151 |
ubootenv@c0000 { |
| 152 |
label = "u-boot-env"; |
| 153 |
reg = <0xc0000 0x20000>; |
| 154 |
}; |
| 155 |
|
| 156 |
kernel-a@e0000 { |
| 157 |
label = "kernel-a"; |
| 158 |
reg = <0xe0000 0x500000>; |
| 159 |
}; |
| 160 |
|
| 161 |
kernel-b@5e0000 { |
| 162 |
label = "kernel-b"; |
| 163 |
reg = <0x5e0000 0x500000>; |
| 164 |
}; |
| 165 |
|
| 166 |
rootfs-a@ae0000 { |
| 167 |
label = "rootfs-a"; |
| 168 |
reg = <0xae0000 0x3000000>; |
| 169 |
}; |
| 170 |
|
| 171 |
rootfs-b@3ae0000 { |
| 172 |
label = "rootfs-b"; |
| 173 |
reg = <0x3ae0000 0x3000000>; |
| 174 |
}; |
| 175 |
|
| 176 |
user@6ae0000 { |
| 177 |
label = "user"; |
| 178 |
reg = <0x6ae0000 0x14e0000>; |
| 179 |
}; |
| 180 |
}; |
| 181 |
}; |
| 182 |
}; |
| 183 |
|
| 184 |
&usb0 { |
| 185 |
atmel,vbus-gpio = <&pioB 13 GPIO_ACTIVE_LOW>; |
| 186 |
pinctrl-names = "default"; |
| 187 |
pinctrl-0 = <&pinctrl_usba_vbus>; |
| 188 |
}; |
| 189 |
|
| 190 |
&usb1 { |
| 191 |
num-ports = <3>; |
| 192 |
atmel,vbus-gpio = <&pioA 2 GPIO_ACTIVE_LOW>; |
| 193 |
atmel,oc-gpio = <&pioA 4 GPIO_ACTIVE_LOW>; |
| 194 |
}; |