| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* at91-sama5d27_wlsom1.dtsi - Device Tree file for SAMA5D27 WLSOM1 |
| 4 |
* |
| 5 |
* Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries |
| 6 |
* |
| 7 |
* Author: Nicolas Ferre <[email protected]> |
| 8 |
* Author: Eugen Hristev <[email protected]> |
| 9 |
*/ |
| 10 |
#include "sama5d2.dtsi" |
| 11 |
#include "sama5d2-pinfunc.h" |
| 12 |
#include <dt-bindings/gpio/gpio.h> |
| 13 |
#include <dt-bindings/mfd/atmel-flexcom.h> |
| 14 |
#include <dt-bindings/pinctrl/at91.h> |
| 15 |
|
| 16 |
/ { |
| 17 |
model = "Microchip SAMA5D27 WLSOM1"; |
| 18 |
compatible = "microchip,sama5d27-wlsom1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5"; |
| 19 |
|
| 20 |
aliases { |
| 21 |
i2c0 = &i2c0; |
| 22 |
}; |
| 23 |
|
| 24 |
clocks { |
| 25 |
slow_xtal { |
| 26 |
clock-frequency = <32768>; |
| 27 |
}; |
| 28 |
|
| 29 |
main_xtal { |
| 30 |
clock-frequency = <24000000>; |
| 31 |
}; |
| 32 |
}; |
| 33 |
|
| 34 |
reg_5v: regulator-5v { |
| 35 |
compatible = "regulator-fixed"; |
| 36 |
regulator-name = "VDD_MAIN"; |
| 37 |
regulator-min-microvolt = <5000000>; |
| 38 |
regulator-max-microvolt = <5000000>; |
| 39 |
regulator-always-on; |
| 40 |
}; |
| 41 |
|
| 42 |
wifi_pwrseq: wifi_pwrseq { |
| 43 |
compatible = "mmc-pwrseq-wilc1000"; |
| 44 |
reset-gpios = <&pioA PIN_PA27 GPIO_ACTIVE_HIGH>; |
| 45 |
powerdown-gpios = <&pioA PIN_PA29 GPIO_ACTIVE_HIGH>; |
| 46 |
pinctrl-0 = <&pinctrl_wilc_pwrseq>; |
| 47 |
pinctrl-names = "default"; |
| 48 |
}; |
| 49 |
}; |
| 50 |
|
| 51 |
&flx1 { |
| 52 |
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>; |
| 53 |
|
| 54 |
uart6: serial@200 { |
| 55 |
pinctrl-0 = <&pinctrl_flx1_default>; |
| 56 |
pinctrl-names = "default"; |
| 57 |
}; |
| 58 |
}; |
| 59 |
|
| 60 |
&i2c0 { |
| 61 |
pinctrl-0 = <&pinctrl_i2c0_default>; |
| 62 |
pinctrl-1 = <&pinctrl_i2c0_gpio>; |
| 63 |
pinctrl-names = "default", "gpio"; |
| 64 |
sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>; |
| 65 |
scl-gpios = <&pioA PIN_PD22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 66 |
status = "okay"; |
| 67 |
}; |
| 68 |
|
| 69 |
&i2c1 { |
| 70 |
dmas = <0>, <0>; |
| 71 |
pinctrl-names = "default", "gpio"; |
| 72 |
pinctrl-0 = <&pinctrl_i2c1_default>; |
| 73 |
pinctrl-1 = <&pinctrl_i2c1_gpio>; |
| 74 |
sda-gpios = <&pioA PIN_PD19 GPIO_ACTIVE_HIGH>; |
| 75 |
scl-gpios = <&pioA PIN_PD20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 76 |
status = "okay"; |
| 77 |
|
| 78 |
pmic@5b { |
| 79 |
compatible = "microchip,mcp16502"; |
| 80 |
reg = <0x5b>; |
| 81 |
lvin-supply = <®_5v>; |
| 82 |
pvin1-supply = <®_5v>; |
| 83 |
pvin2-supply = <®_5v>; |
| 84 |
pvin3-supply = <®_5v>; |
| 85 |
pvin4-supply = <®_5v>; |
| 86 |
status = "okay"; |
| 87 |
lpm-gpios = <&pioBU 0 GPIO_ACTIVE_LOW>; |
| 88 |
|
| 89 |
regulators { |
| 90 |
vdd_3v3: VDD_IO { |
| 91 |
regulator-name = "VDD_IO"; |
| 92 |
regulator-min-microvolt = <3300000>; |
| 93 |
regulator-max-microvolt = <3300000>; |
| 94 |
regulator-initial-mode = <2>; |
| 95 |
regulator-allowed-modes = <2>, <4>; |
| 96 |
regulator-always-on; |
| 97 |
|
| 98 |
regulator-state-standby { |
| 99 |
regulator-on-in-suspend; |
| 100 |
regulator-mode = <4>; |
| 101 |
}; |
| 102 |
|
| 103 |
regulator-state-mem { |
| 104 |
regulator-off-in-suspend; |
| 105 |
regulator-mode = <4>; |
| 106 |
}; |
| 107 |
}; |
| 108 |
|
| 109 |
vddio_ddr: VDD_DDR { |
| 110 |
regulator-name = "VDD_DDR"; |
| 111 |
regulator-min-microvolt = <1200000>; |
| 112 |
regulator-max-microvolt = <1200000>; |
| 113 |
regulator-initial-mode = <2>; |
| 114 |
regulator-allowed-modes = <2>, <4>; |
| 115 |
regulator-always-on; |
| 116 |
|
| 117 |
regulator-state-standby { |
| 118 |
regulator-on-in-suspend; |
| 119 |
regulator-suspend-microvolt = <1200000>; |
| 120 |
regulator-changeable-in-suspend; |
| 121 |
regulator-mode = <4>; |
| 122 |
}; |
| 123 |
|
| 124 |
regulator-state-mem { |
| 125 |
regulator-on-in-suspend; |
| 126 |
regulator-suspend-microvolt = <1200000>; |
| 127 |
regulator-changeable-in-suspend; |
| 128 |
regulator-mode = <4>; |
| 129 |
}; |
| 130 |
}; |
| 131 |
|
| 132 |
vdd_core: VDD_CORE { |
| 133 |
regulator-name = "VDD_CORE"; |
| 134 |
regulator-min-microvolt = <1250000>; |
| 135 |
regulator-max-microvolt = <1250000>; |
| 136 |
regulator-initial-mode = <2>; |
| 137 |
regulator-allowed-modes = <2>, <4>; |
| 138 |
regulator-always-on; |
| 139 |
|
| 140 |
regulator-state-standby { |
| 141 |
regulator-on-in-suspend; |
| 142 |
regulator-mode = <4>; |
| 143 |
}; |
| 144 |
|
| 145 |
regulator-state-mem { |
| 146 |
regulator-off-in-suspend; |
| 147 |
regulator-mode = <4>; |
| 148 |
}; |
| 149 |
}; |
| 150 |
|
| 151 |
vdd_ddr: VDD_OTHER { |
| 152 |
regulator-name = "VDD_OTHER"; |
| 153 |
regulator-min-microvolt = <1800000>; |
| 154 |
regulator-max-microvolt = <1800000>; |
| 155 |
regulator-initial-mode = <2>; |
| 156 |
regulator-allowed-modes = <2>, <4>; |
| 157 |
regulator-always-on; |
| 158 |
|
| 159 |
regulator-state-standby { |
| 160 |
regulator-on-in-suspend; |
| 161 |
regulator-suspend-microvolt = <1800000>; |
| 162 |
regulator-changeable-in-suspend; |
| 163 |
regulator-mode = <4>; |
| 164 |
}; |
| 165 |
|
| 166 |
regulator-state-mem { |
| 167 |
regulator-on-in-suspend; |
| 168 |
regulator-suspend-microvolt = <1800000>; |
| 169 |
regulator-changeable-in-suspend; |
| 170 |
regulator-mode = <4>; |
| 171 |
}; |
| 172 |
}; |
| 173 |
|
| 174 |
LDO1 { |
| 175 |
regulator-name = "LDO1"; |
| 176 |
regulator-min-microvolt = <3300000>; |
| 177 |
regulator-max-microvolt = <3300000>; |
| 178 |
regulator-always-on; |
| 179 |
|
| 180 |
regulator-state-standby { |
| 181 |
regulator-on-in-suspend; |
| 182 |
}; |
| 183 |
|
| 184 |
regulator-state-mem { |
| 185 |
regulator-off-in-suspend; |
| 186 |
}; |
| 187 |
}; |
| 188 |
|
| 189 |
LDO2 { |
| 190 |
regulator-name = "LDO2"; |
| 191 |
regulator-min-microvolt = <1800000>; |
| 192 |
regulator-max-microvolt = <3300000>; |
| 193 |
|
| 194 |
regulator-state-standby { |
| 195 |
regulator-on-in-suspend; |
| 196 |
}; |
| 197 |
|
| 198 |
regulator-state-mem { |
| 199 |
regulator-off-in-suspend; |
| 200 |
}; |
| 201 |
}; |
| 202 |
}; |
| 203 |
}; |
| 204 |
}; |
| 205 |
|
| 206 |
&macb0 { |
| 207 |
pinctrl-names = "default"; |
| 208 |
pinctrl-0 = <&pinctrl_macb0_default>; |
| 209 |
#address-cells = <1>; |
| 210 |
#size-cells = <0>; |
| 211 |
phy-mode = "rmii"; |
| 212 |
|
| 213 |
ethernet-phy@0 { |
| 214 |
reg = <0x0>; |
| 215 |
interrupt-parent = <&pioA>; |
| 216 |
interrupts = <PIN_PB24 IRQ_TYPE_LEVEL_LOW>; |
| 217 |
pinctrl-names = "default"; |
| 218 |
pinctrl-0 = <&pinctrl_macb0_phy_irq>; |
| 219 |
}; |
| 220 |
}; |
| 221 |
|
| 222 |
&pmc { |
| 223 |
atmel,osc-bypass; |
| 224 |
}; |
| 225 |
|
| 226 |
&qspi1 { |
| 227 |
pinctrl-names = "default"; |
| 228 |
pinctrl-0 = <&pinctrl_qspi1_default>; |
| 229 |
status = "disabled"; |
| 230 |
|
| 231 |
qspi1_flash: flash@0 { |
| 232 |
#address-cells = <1>; |
| 233 |
#size-cells = <1>; |
| 234 |
compatible = "jedec,spi-nor"; |
| 235 |
reg = <0>; |
| 236 |
spi-max-frequency = <104000000>; |
| 237 |
spi-cs-setup-delay-ns = <7>; |
| 238 |
spi-rx-bus-width = <4>; |
| 239 |
spi-tx-bus-width = <4>; |
| 240 |
m25p,fast-read; |
| 241 |
status = "disabled"; |
| 242 |
|
| 243 |
at91bootstrap@0 { |
| 244 |
label = "at91bootstrap"; |
| 245 |
reg = <0x0 0x40000>; |
| 246 |
}; |
| 247 |
|
| 248 |
bootloader@40000 { |
| 249 |
label = "bootloader"; |
| 250 |
reg = <0x40000 0xc0000>; |
| 251 |
}; |
| 252 |
|
| 253 |
bootloaderenvred@100000 { |
| 254 |
label = "bootloader env redundant"; |
| 255 |
reg = <0x100000 0x40000>; |
| 256 |
}; |
| 257 |
|
| 258 |
bootloaderenv@140000 { |
| 259 |
label = "bootloader env"; |
| 260 |
reg = <0x140000 0x40000>; |
| 261 |
}; |
| 262 |
|
| 263 |
dtb@180000 { |
| 264 |
label = "device tree"; |
| 265 |
reg = <0x180000 0x80000>; |
| 266 |
}; |
| 267 |
|
| 268 |
kernel@200000 { |
| 269 |
label = "kernel"; |
| 270 |
reg = <0x200000 0x600000>; |
| 271 |
}; |
| 272 |
}; |
| 273 |
}; |
| 274 |
|
| 275 |
&pioA { |
| 276 |
pinctrl_flx1_default: flx1_usart_default { |
| 277 |
pinmux = <PIN_PA24__FLEXCOM1_IO0>, |
| 278 |
<PIN_PA23__FLEXCOM1_IO1>, |
| 279 |
<PIN_PA25__FLEXCOM1_IO3>, |
| 280 |
<PIN_PA26__FLEXCOM1_IO4>; |
| 281 |
bias-disable; |
| 282 |
}; |
| 283 |
|
| 284 |
pinctrl_i2c0_default: i2c0_default { |
| 285 |
pinmux = <PIN_PD21__TWD0>, |
| 286 |
<PIN_PD22__TWCK0>; |
| 287 |
bias-disable; |
| 288 |
}; |
| 289 |
|
| 290 |
pinctrl_i2c0_gpio: i2c0_gpio { |
| 291 |
pinmux = <PIN_PD21__GPIO>, |
| 292 |
<PIN_PD22__GPIO>; |
| 293 |
bias-disable; |
| 294 |
}; |
| 295 |
|
| 296 |
pinctrl_i2c1_default: i2c1_default { |
| 297 |
pinmux = <PIN_PD19__TWD1>, |
| 298 |
<PIN_PD20__TWCK1>; |
| 299 |
bias-disable; |
| 300 |
}; |
| 301 |
|
| 302 |
pinctrl_i2c1_gpio: i2c1_gpio { |
| 303 |
pinmux = <PIN_PD19__GPIO>, |
| 304 |
<PIN_PD20__GPIO>; |
| 305 |
bias-disable; |
| 306 |
}; |
| 307 |
|
| 308 |
pinctrl_macb0_default: macb0_default { |
| 309 |
pinmux = <PIN_PB14__GTXCK>, |
| 310 |
<PIN_PB15__GTXEN>, |
| 311 |
<PIN_PB16__GRXDV>, |
| 312 |
<PIN_PB17__GRXER>, |
| 313 |
<PIN_PB18__GRX0>, |
| 314 |
<PIN_PB19__GRX1>, |
| 315 |
<PIN_PB20__GTX0>, |
| 316 |
<PIN_PB21__GTX1>, |
| 317 |
<PIN_PB22__GMDC>, |
| 318 |
<PIN_PB23__GMDIO>; |
| 319 |
bias-disable; |
| 320 |
}; |
| 321 |
|
| 322 |
pinctrl_macb0_phy_irq: macb0_phy_irq { |
| 323 |
pinmux = <PIN_PB24__GPIO>; |
| 324 |
bias-disable; |
| 325 |
}; |
| 326 |
|
| 327 |
pinctrl_qspi1_default: qspi1_default { |
| 328 |
pinmux = <PIN_PB5__QSPI1_SCK>, |
| 329 |
<PIN_PB6__QSPI1_CS>, |
| 330 |
<PIN_PB7__QSPI1_IO0>, |
| 331 |
<PIN_PB8__QSPI1_IO1>, |
| 332 |
<PIN_PB9__QSPI1_IO2>, |
| 333 |
<PIN_PB10__QSPI1_IO3>; |
| 334 |
bias-pull-up; |
| 335 |
}; |
| 336 |
|
| 337 |
pinctrl_sdmmc1_default: sdmmc1_default { |
| 338 |
cmd-data { |
| 339 |
pinmux = <PIN_PA28__SDMMC1_CMD>, |
| 340 |
<PIN_PA18__SDMMC1_DAT0>, |
| 341 |
<PIN_PA19__SDMMC1_DAT1>, |
| 342 |
<PIN_PA20__SDMMC1_DAT2>, |
| 343 |
<PIN_PA21__SDMMC1_DAT3>; |
| 344 |
bias-disable; |
| 345 |
}; |
| 346 |
|
| 347 |
conf-ck { |
| 348 |
pinmux = <PIN_PA22__SDMMC1_CK>; |
| 349 |
bias-disable; |
| 350 |
}; |
| 351 |
}; |
| 352 |
|
| 353 |
pinctrl_wilc_default: wilc_default { |
| 354 |
conf-irq { |
| 355 |
pinmux = <PIN_PB25__GPIO>; |
| 356 |
bias-disable; |
| 357 |
}; |
| 358 |
}; |
| 359 |
|
| 360 |
pinctrl_wilc_pwrseq: wilc_pwrseq { |
| 361 |
conf-ce-nrst { |
| 362 |
pinmux = <PIN_PA27__GPIO>, |
| 363 |
<PIN_PA29__GPIO>; |
| 364 |
bias-disable; |
| 365 |
}; |
| 366 |
|
| 367 |
conf-rtcclk { |
| 368 |
pinmux = <PIN_PB13__PCK1>; |
| 369 |
bias-disable; |
| 370 |
}; |
| 371 |
}; |
| 372 |
}; |
| 373 |
|
| 374 |
&sdmmc1 { |
| 375 |
#address-cells = <1>; |
| 376 |
#size-cells = <0>; |
| 377 |
bus-width = <4>; |
| 378 |
pinctrl-names = "default"; |
| 379 |
pinctrl-0 = <&pinctrl_sdmmc1_default>; |
| 380 |
mmc-pwrseq = <&wifi_pwrseq>; |
| 381 |
no-1-8-v; |
| 382 |
non-removable; |
| 383 |
bus-width = <4>; |
| 384 |
status = "okay"; |
| 385 |
|
| 386 |
wilc: wifi@0 { |
| 387 |
reg = <0>; |
| 388 |
compatible = "microchip,wilc3000", "microchip,wilc1000"; |
| 389 |
pinctrl-names = "default"; |
| 390 |
pinctrl-0 = <&pinctrl_wilc_default>; |
| 391 |
clocks = <&pmc PMC_TYPE_SYSTEM 9>; |
| 392 |
clock-names = "rtc"; |
| 393 |
interrupts = <PIN_PB25 IRQ_TYPE_NONE>; |
| 394 |
interrupt-parent = <&pioA>; |
| 395 |
assigned-clocks = <&pmc PMC_TYPE_SYSTEM 9>; |
| 396 |
assigned-clock-rates = <32768>; |
| 397 |
}; |
| 398 |
}; |
| 399 |
|