| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* at91sam9m10g45ek.dts - Device Tree file for AT91SAM9M10G45-EK board |
| 4 |
* |
| 5 |
* Copyright (C) 2011 Atmel, |
| 6 |
* 2011 Nicolas Ferre <[email protected]> |
| 7 |
*/ |
| 8 |
/dts-v1/; |
| 9 |
#include "at91sam9g45.dtsi" |
| 10 |
#include <dt-bindings/pwm/pwm.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
model = "Atmel AT91SAM9M10G45-EK"; |
| 14 |
compatible = "atmel,at91sam9m10g45ek", "atmel,at91sam9g45", "atmel,at91sam9"; |
| 15 |
|
| 16 |
chosen { |
| 17 |
bootargs = "mem=64M root=/dev/mtdblock1 rw rootfstype=jffs2"; |
| 18 |
stdout-path = "serial0:115200n8"; |
| 19 |
}; |
| 20 |
|
| 21 |
memory@70000000 { |
| 22 |
reg = <0x70000000 0x4000000>; |
| 23 |
}; |
| 24 |
|
| 25 |
clocks { |
| 26 |
slow_xtal { |
| 27 |
clock-frequency = <32768>; |
| 28 |
}; |
| 29 |
|
| 30 |
main_xtal { |
| 31 |
clock-frequency = <12000000>; |
| 32 |
}; |
| 33 |
}; |
| 34 |
|
| 35 |
ahb { |
| 36 |
apb { |
| 37 |
dbgu: serial@ffffee00 { |
| 38 |
status = "okay"; |
| 39 |
}; |
| 40 |
|
| 41 |
tcb0: timer@fff7c000 { |
| 42 |
timer@0 { |
| 43 |
compatible = "atmel,tcb-timer"; |
| 44 |
reg = <0>, <1>; |
| 45 |
}; |
| 46 |
|
| 47 |
timer@2 { |
| 48 |
compatible = "atmel,tcb-timer"; |
| 49 |
reg = <2>; |
| 50 |
}; |
| 51 |
}; |
| 52 |
|
| 53 |
usart1: serial@fff90000 { |
| 54 |
pinctrl-0 = |
| 55 |
<&pinctrl_usart1 |
| 56 |
&pinctrl_usart1_rts |
| 57 |
&pinctrl_usart1_cts>; |
| 58 |
status = "okay"; |
| 59 |
}; |
| 60 |
|
| 61 |
macb0: ethernet@fffbc000 { |
| 62 |
phy-mode = "rmii"; |
| 63 |
status = "okay"; |
| 64 |
}; |
| 65 |
|
| 66 |
i2c0: i2c@fff84000 { |
| 67 |
status = "okay"; |
| 68 |
ov2640: camera@30 { |
| 69 |
compatible = "ovti,ov2640"; |
| 70 |
reg = <0x30>; |
| 71 |
pinctrl-names = "default"; |
| 72 |
pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; |
| 73 |
resetb-gpios = <&pioD 12 GPIO_ACTIVE_LOW>; |
| 74 |
pwdn-gpios = <&pioD 13 GPIO_ACTIVE_HIGH>; |
| 75 |
clocks = <&pmc PMC_TYPE_SYSTEM 9>; |
| 76 |
clock-names = "xvclk"; |
| 77 |
assigned-clocks = <&pmc PMC_TYPE_SYSTEM 9>; |
| 78 |
assigned-clock-rates = <25000000>; |
| 79 |
|
| 80 |
port { |
| 81 |
ov2640_0: endpoint { |
| 82 |
remote-endpoint = <&isi_0>; |
| 83 |
bus-width = <8>; |
| 84 |
}; |
| 85 |
}; |
| 86 |
}; |
| 87 |
}; |
| 88 |
|
| 89 |
i2c1: i2c@fff88000 { |
| 90 |
status = "okay"; |
| 91 |
}; |
| 92 |
|
| 93 |
watchdog@fffffd40 { |
| 94 |
status = "okay"; |
| 95 |
}; |
| 96 |
|
| 97 |
mmc0: mmc@fff80000 { |
| 98 |
pinctrl-0 = < |
| 99 |
&pinctrl_board_mmc0 |
| 100 |
&pinctrl_mmc0_slot0_clk_cmd_dat0 |
| 101 |
&pinctrl_mmc0_slot0_dat1_3>; |
| 102 |
pinctrl-names = "default"; |
| 103 |
status = "okay"; |
| 104 |
slot@0 { |
| 105 |
reg = <0>; |
| 106 |
bus-width = <4>; |
| 107 |
cd-gpios = <&pioD 10 GPIO_ACTIVE_HIGH>; |
| 108 |
}; |
| 109 |
}; |
| 110 |
|
| 111 |
mmc1: mmc@fffd0000 { |
| 112 |
pinctrl-0 = < |
| 113 |
&pinctrl_board_mmc1 |
| 114 |
&pinctrl_mmc1_slot0_clk_cmd_dat0 |
| 115 |
&pinctrl_mmc1_slot0_dat1_3>; |
| 116 |
pinctrl-names = "default"; |
| 117 |
status = "okay"; |
| 118 |
slot@0 { |
| 119 |
reg = <0>; |
| 120 |
bus-width = <4>; |
| 121 |
cd-gpios = <&pioD 11 GPIO_ACTIVE_HIGH>; |
| 122 |
wp-gpios = <&pioD 29 GPIO_ACTIVE_HIGH>; |
| 123 |
}; |
| 124 |
}; |
| 125 |
|
| 126 |
pinctrl@fffff200 { |
| 127 |
camera_sensor { |
| 128 |
pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 { |
| 129 |
atmel,pins = |
| 130 |
<AT91_PIOB 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; |
| 131 |
}; |
| 132 |
|
| 133 |
pinctrl_sensor_reset: sensor_reset-0 { |
| 134 |
atmel,pins = |
| 135 |
<AT91_PIOD 12 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; |
| 136 |
}; |
| 137 |
|
| 138 |
pinctrl_sensor_power: sensor_power-0 { |
| 139 |
atmel,pins = |
| 140 |
<AT91_PIOD 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; |
| 141 |
}; |
| 142 |
}; |
| 143 |
mmc0 { |
| 144 |
pinctrl_board_mmc0: mmc0-board { |
| 145 |
atmel,pins = |
| 146 |
<AT91_PIOD 10 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD10 gpio CD pin pull up and deglitch */ |
| 147 |
}; |
| 148 |
}; |
| 149 |
|
| 150 |
mmc1 { |
| 151 |
pinctrl_board_mmc1: mmc1-board { |
| 152 |
atmel,pins = |
| 153 |
<AT91_PIOD 11 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH /* PD11 gpio CD pin pull up and deglitch */ |
| 154 |
AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>; /* PD29 gpio WP pin pull up */ |
| 155 |
}; |
| 156 |
}; |
| 157 |
|
| 158 |
pwm0 { |
| 159 |
pinctrl_pwm_leds: pwm-led { |
| 160 |
atmel,pins = |
| 161 |
<AT91_PIOD 0 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PD0 periph B */ |
| 162 |
AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; /* PD31 periph B */ |
| 163 |
}; |
| 164 |
}; |
| 165 |
}; |
| 166 |
|
| 167 |
spi0: spi@fffa4000 { |
| 168 |
status = "okay"; |
| 169 |
cs-gpios = <&pioB 3 0>, <0>, <0>, <0>; |
| 170 |
flash@0 { |
| 171 |
compatible = "atmel,at45", "atmel,dataflash"; |
| 172 |
spi-max-frequency = <13000000>; |
| 173 |
reg = <0>; |
| 174 |
}; |
| 175 |
}; |
| 176 |
|
| 177 |
usb2: gadget@fff78000 { |
| 178 |
atmel,vbus-gpio = <&pioB 19 GPIO_ACTIVE_HIGH>; |
| 179 |
status = "okay"; |
| 180 |
}; |
| 181 |
|
| 182 |
ac97: sound@fffac000 { |
| 183 |
status = "okay"; |
| 184 |
}; |
| 185 |
|
| 186 |
adc0: adc@fffb0000 { |
| 187 |
pinctrl-names = "default"; |
| 188 |
pinctrl-0 = < |
| 189 |
&pinctrl_adc0_ad0 |
| 190 |
&pinctrl_adc0_ad1 |
| 191 |
&pinctrl_adc0_ad2 |
| 192 |
&pinctrl_adc0_ad3 |
| 193 |
&pinctrl_adc0_ad4 |
| 194 |
&pinctrl_adc0_ad5 |
| 195 |
&pinctrl_adc0_ad6 |
| 196 |
&pinctrl_adc0_ad7>; |
| 197 |
atmel,adc-ts-wires = <4>; |
| 198 |
status = "okay"; |
| 199 |
}; |
| 200 |
|
| 201 |
isi@fffb4000 { |
| 202 |
pinctrl-names = "default"; |
| 203 |
pinctrl-0 = <&pinctrl_isi_data_0_7>; |
| 204 |
status = "okay"; |
| 205 |
port { |
| 206 |
isi_0: endpoint { |
| 207 |
remote-endpoint = <&ov2640_0>; |
| 208 |
bus-width = <8>; |
| 209 |
vsync-active = <1>; |
| 210 |
hsync-active = <1>; |
| 211 |
}; |
| 212 |
}; |
| 213 |
}; |
| 214 |
|
| 215 |
pwm0: pwm@fffb8000 { |
| 216 |
status = "okay"; |
| 217 |
|
| 218 |
pinctrl-names = "default"; |
| 219 |
pinctrl-0 = <&pinctrl_pwm_leds>; |
| 220 |
}; |
| 221 |
|
| 222 |
rtc@fffffd20 { |
| 223 |
atmel,rtt-rtc-time-reg = <&gpbr 0x0>; |
| 224 |
status = "okay"; |
| 225 |
}; |
| 226 |
|
| 227 |
gpbr: syscon@fffffd60 { |
| 228 |
status = "okay"; |
| 229 |
}; |
| 230 |
|
| 231 |
rtc@fffffdb0 { |
| 232 |
status = "okay"; |
| 233 |
}; |
| 234 |
}; |
| 235 |
|
| 236 |
fb0: fb@500000 { |
| 237 |
display = <&display0>; |
| 238 |
status = "okay"; |
| 239 |
|
| 240 |
display0: panel { |
| 241 |
bits-per-pixel = <32>; |
| 242 |
atmel,lcdcon-backlight; |
| 243 |
atmel,dmacon = <0x1>; |
| 244 |
atmel,lcdcon2 = <0x80008002>; |
| 245 |
atmel,guard-time = <9>; |
| 246 |
atmel,lcd-wiring-mode = "RGB"; |
| 247 |
|
| 248 |
display-timings { |
| 249 |
native-mode = <&timing0>; |
| 250 |
timing0: timing0 { |
| 251 |
clock-frequency = <9000000>; |
| 252 |
hactive = <480>; |
| 253 |
vactive = <272>; |
| 254 |
hback-porch = <1>; |
| 255 |
hfront-porch = <1>; |
| 256 |
vback-porch = <40>; |
| 257 |
vfront-porch = <1>; |
| 258 |
hsync-len = <45>; |
| 259 |
vsync-len = <1>; |
| 260 |
}; |
| 261 |
}; |
| 262 |
}; |
| 263 |
}; |
| 264 |
|
| 265 |
ebi: ebi@10000000 { |
| 266 |
status = "okay"; |
| 267 |
|
| 268 |
nand_controller: nand-controller { |
| 269 |
status = "okay"; |
| 270 |
pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>; |
| 271 |
pinctrl-names = "default"; |
| 272 |
|
| 273 |
nand@3 { |
| 274 |
reg = <0x3 0x0 0x800000>; |
| 275 |
rb-gpios = <&pioC 8 GPIO_ACTIVE_HIGH>; |
| 276 |
cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>; |
| 277 |
nand-bus-width = <8>; |
| 278 |
nand-ecc-mode = "soft"; |
| 279 |
nand-on-flash-bbt; |
| 280 |
label = "atmel_nand"; |
| 281 |
|
| 282 |
partitions { |
| 283 |
compatible = "fixed-partitions"; |
| 284 |
#address-cells = <1>; |
| 285 |
#size-cells = <1>; |
| 286 |
|
| 287 |
boot@0 { |
| 288 |
label = "bootstrap/uboot/kernel"; |
| 289 |
reg = <0x0 0x400000>; |
| 290 |
}; |
| 291 |
|
| 292 |
rootfs@400000 { |
| 293 |
label = "rootfs"; |
| 294 |
reg = <0x400000 0x3C00000>; |
| 295 |
}; |
| 296 |
|
| 297 |
data@4000000 { |
| 298 |
label = "data"; |
| 299 |
reg = <0x4000000 0xC000000>; |
| 300 |
}; |
| 301 |
}; |
| 302 |
}; |
| 303 |
}; |
| 304 |
}; |
| 305 |
|
| 306 |
usb0: usb@700000 { |
| 307 |
status = "okay"; |
| 308 |
num-ports = <2>; |
| 309 |
atmel,vbus-gpio = <&pioD 1 GPIO_ACTIVE_LOW |
| 310 |
&pioD 3 GPIO_ACTIVE_LOW>; |
| 311 |
}; |
| 312 |
|
| 313 |
usb1: usb@800000 { |
| 314 |
status = "okay"; |
| 315 |
}; |
| 316 |
}; |
| 317 |
|
| 318 |
led-controller-1 { |
| 319 |
compatible = "gpio-leds"; |
| 320 |
|
| 321 |
led-1 { |
| 322 |
label = "d8"; |
| 323 |
gpios = <&pioD 30 GPIO_ACTIVE_HIGH>; |
| 324 |
linux,default-trigger = "heartbeat"; |
| 325 |
}; |
| 326 |
}; |
| 327 |
|
| 328 |
led-controller-2 { |
| 329 |
compatible = "pwm-leds"; |
| 330 |
|
| 331 |
led-2 { |
| 332 |
label = "d6"; |
| 333 |
pwms = <&pwm0 3 5000 PWM_POLARITY_INVERTED>; |
| 334 |
max-brightness = <255>; |
| 335 |
linux,default-trigger = "nand-disk"; |
| 336 |
}; |
| 337 |
|
| 338 |
led-3 { |
| 339 |
label = "d7"; |
| 340 |
pwms = <&pwm0 1 5000 PWM_POLARITY_INVERTED>; |
| 341 |
max-brightness = <255>; |
| 342 |
linux,default-trigger = "mmc0"; |
| 343 |
}; |
| 344 |
}; |
| 345 |
|
| 346 |
gpio-keys { |
| 347 |
compatible = "gpio-keys"; |
| 348 |
|
| 349 |
button-left-click { |
| 350 |
label = "left_click"; |
| 351 |
gpios = <&pioB 6 GPIO_ACTIVE_LOW>; |
| 352 |
linux,code = <272>; |
| 353 |
wakeup-source; |
| 354 |
}; |
| 355 |
|
| 356 |
button-right-click { |
| 357 |
label = "right_click"; |
| 358 |
gpios = <&pioB 7 GPIO_ACTIVE_LOW>; |
| 359 |
linux,code = <273>; |
| 360 |
wakeup-source; |
| 361 |
}; |
| 362 |
|
| 363 |
button-left { |
| 364 |
label = "Joystick Left"; |
| 365 |
gpios = <&pioB 14 GPIO_ACTIVE_LOW>; |
| 366 |
linux,code = <105>; |
| 367 |
}; |
| 368 |
|
| 369 |
button-right { |
| 370 |
label = "Joystick Right"; |
| 371 |
gpios = <&pioB 15 GPIO_ACTIVE_LOW>; |
| 372 |
linux,code = <106>; |
| 373 |
}; |
| 374 |
|
| 375 |
button-up { |
| 376 |
label = "Joystick Up"; |
| 377 |
gpios = <&pioB 16 GPIO_ACTIVE_LOW>; |
| 378 |
linux,code = <103>; |
| 379 |
}; |
| 380 |
|
| 381 |
button-down { |
| 382 |
label = "Joystick Down"; |
| 383 |
gpios = <&pioB 17 GPIO_ACTIVE_LOW>; |
| 384 |
linux,code = <108>; |
| 385 |
}; |
| 386 |
|
| 387 |
button-enter { |
| 388 |
label = "Joystick Press"; |
| 389 |
gpios = <&pioB 18 GPIO_ACTIVE_LOW>; |
| 390 |
linux,code = <28>; |
| 391 |
}; |
| 392 |
}; |
| 393 |
}; |