| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* at91sam9x5ek.dtsi - Device Tree file for AT91SAM9x5CM Base board |
| 4 |
* |
| 5 |
* Copyright (C) 2012 Atmel, |
| 6 |
* 2012 Nicolas Ferre <[email protected]> |
| 7 |
*/ |
| 8 |
#include "at91sam9x5cm.dtsi" |
| 9 |
|
| 10 |
/ { |
| 11 |
model = "Atmel AT91SAM9X5-EK"; |
| 12 |
compatible = "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9"; |
| 13 |
|
| 14 |
chosen { |
| 15 |
bootargs = "root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs"; |
| 16 |
stdout-path = "serial0:115200n8"; |
| 17 |
}; |
| 18 |
|
| 19 |
sound { |
| 20 |
compatible = "atmel,sam9x5-wm8731-audio"; |
| 21 |
|
| 22 |
atmel,model = "wm8731 @ AT91SAM9X5EK"; |
| 23 |
|
| 24 |
atmel,audio-routing = |
| 25 |
"Headphone Jack", "RHPOUT", |
| 26 |
"Headphone Jack", "LHPOUT", |
| 27 |
"LLINEIN", "Line In Jack", |
| 28 |
"RLINEIN", "Line In Jack"; |
| 29 |
|
| 30 |
atmel,ssc-controller = <&ssc0>; |
| 31 |
atmel,audio-codec = <&wm8731>; |
| 32 |
}; |
| 33 |
}; |
| 34 |
|
| 35 |
&adc0 { |
| 36 |
atmel,adc-ts-wires = <4>; |
| 37 |
atmel,adc-ts-pressure-threshold = <10000>; |
| 38 |
status = "okay"; |
| 39 |
}; |
| 40 |
|
| 41 |
&dbgu { |
| 42 |
atmel,use-dma-rx; |
| 43 |
atmel,use-dma-tx; |
| 44 |
status = "okay"; |
| 45 |
}; |
| 46 |
|
| 47 |
&i2c0 { |
| 48 |
status = "okay"; |
| 49 |
|
| 50 |
wm8731: wm8731@1a { |
| 51 |
compatible = "wm8731"; |
| 52 |
reg = <0x1a>; |
| 53 |
}; |
| 54 |
}; |
| 55 |
|
| 56 |
&mmc0 { |
| 57 |
pinctrl-0 = < |
| 58 |
&pinctrl_board_mmc0 |
| 59 |
&pinctrl_mmc0_slot0_clk_cmd_dat0 |
| 60 |
&pinctrl_mmc0_slot0_dat1_3>; |
| 61 |
pinctrl-names = "default"; |
| 62 |
status = "okay"; |
| 63 |
|
| 64 |
slot@0 { |
| 65 |
reg = <0>; |
| 66 |
bus-width = <4>; |
| 67 |
cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>; |
| 68 |
}; |
| 69 |
}; |
| 70 |
|
| 71 |
&mmc1 { |
| 72 |
pinctrl-0 = < |
| 73 |
&pinctrl_board_mmc1 |
| 74 |
&pinctrl_mmc1_slot0_clk_cmd_dat0 |
| 75 |
&pinctrl_mmc1_slot0_dat1_3>; |
| 76 |
pinctrl-names = "default"; |
| 77 |
status = "okay"; |
| 78 |
|
| 79 |
slot@0 { |
| 80 |
reg = <0>; |
| 81 |
bus-width = <4>; |
| 82 |
cd-gpios = <&pioD 14 GPIO_ACTIVE_HIGH>; |
| 83 |
}; |
| 84 |
}; |
| 85 |
|
| 86 |
&pinctrl { |
| 87 |
camera_sensor { |
| 88 |
pinctrl_pck0_as_isi_mck: pck0_as_isi_mck-0 { |
| 89 |
atmel,pins = |
| 90 |
<AT91_PIOC 15 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* ISI_MCK */ |
| 91 |
}; |
| 92 |
|
| 93 |
pinctrl_sensor_power: sensor_power-0 { |
| 94 |
atmel,pins = |
| 95 |
<AT91_PIOA 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; |
| 96 |
}; |
| 97 |
|
| 98 |
pinctrl_sensor_reset: sensor_reset-0 { |
| 99 |
atmel,pins = |
| 100 |
<AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; |
| 101 |
}; |
| 102 |
}; |
| 103 |
|
| 104 |
mmc0 { |
| 105 |
pinctrl_board_mmc0: mmc0-board { |
| 106 |
atmel,pins = |
| 107 |
<AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD15 gpio CD pin pull up and deglitch */ |
| 108 |
}; |
| 109 |
}; |
| 110 |
|
| 111 |
mmc1 { |
| 112 |
pinctrl_board_mmc1: mmc1-board { |
| 113 |
atmel,pins = |
| 114 |
<AT91_PIOD 14 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD14 gpio CD pin pull up and deglitch */ |
| 115 |
}; |
| 116 |
}; |
| 117 |
|
| 118 |
usb2 { |
| 119 |
pinctrl_board_usb2: usb2-board { |
| 120 |
atmel,pins = |
| 121 |
<AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PB16 gpio vbus sense, deglitch */ |
| 122 |
}; |
| 123 |
}; |
| 124 |
}; |
| 125 |
|
| 126 |
&spi0 { |
| 127 |
cs-gpios = <&pioA 14 0>, <0>, <0>, <0>; |
| 128 |
status = "disabled"; /* conflicts with mmc1 */ |
| 129 |
|
| 130 |
flash@0 { |
| 131 |
compatible = "atmel,at25df321a"; |
| 132 |
spi-max-frequency = <50000000>; |
| 133 |
reg = <0>; |
| 134 |
}; |
| 135 |
}; |
| 136 |
|
| 137 |
&ssc0 { |
| 138 |
status = "okay"; |
| 139 |
}; |
| 140 |
|
| 141 |
&usart0 { |
| 142 |
atmel,use-dma-rx; |
| 143 |
atmel,use-dma-tx; |
| 144 |
status = "okay"; |
| 145 |
}; |
| 146 |
|
| 147 |
&usb0 { |
| 148 |
num-ports = <3>; |
| 149 |
atmel,vbus-gpio = <0 /* &pioD 18 GPIO_ACTIVE_LOW *//* Activate to have access to port A */ |
| 150 |
&pioD 19 GPIO_ACTIVE_LOW |
| 151 |
&pioD 20 GPIO_ACTIVE_LOW |
| 152 |
>; |
| 153 |
status = "okay"; |
| 154 |
}; |
| 155 |
|
| 156 |
&usb1 { |
| 157 |
status = "okay"; |
| 158 |
}; |
| 159 |
|
| 160 |
&usb2 { |
| 161 |
pinctrl-names = "default"; |
| 162 |
pinctrl-0 = <&pinctrl_board_usb2>; |
| 163 |
atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>; |
| 164 |
status = "okay"; |
| 165 |
}; |
| 166 |
|
| 167 |
&watchdog { |
| 168 |
status = "okay"; |
| 169 |
}; |