| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* animeo_ip.dts - Device Tree file for Somfy Animeo IP Boards |
| 4 |
* |
| 5 |
* Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <[email protected]> |
| 6 |
*/ |
| 7 |
|
| 8 |
/dts-v1/; |
| 9 |
#include "at91sam9260.dtsi" |
| 10 |
|
| 11 |
/ { |
| 12 |
model = "Somfy Animeo IP"; |
| 13 |
compatible = "somfy,animeo-ip", "atmel,at91sam9260", "atmel,at91sam9"; |
| 14 |
|
| 15 |
aliases { |
| 16 |
serial0 = &usart1; |
| 17 |
serial1 = &usart2; |
| 18 |
serial2 = &usart0; |
| 19 |
serial3 = &dbgu; |
| 20 |
serial4 = &usart3; |
| 21 |
serial5 = &uart0; |
| 22 |
serial6 = &uart1; |
| 23 |
}; |
| 24 |
|
| 25 |
chosen { |
| 26 |
stdout-path = &usart2; |
| 27 |
}; |
| 28 |
|
| 29 |
memory@20000000 { |
| 30 |
reg = <0x20000000 0x4000000>; |
| 31 |
}; |
| 32 |
|
| 33 |
clocks { |
| 34 |
slow_xtal { |
| 35 |
clock-frequency = <32768>; |
| 36 |
}; |
| 37 |
|
| 38 |
main_xtal { |
| 39 |
clock-frequency = <18432000>; |
| 40 |
}; |
| 41 |
}; |
| 42 |
|
| 43 |
ahb { |
| 44 |
apb { |
| 45 |
tcb0: timer@fffa0000 { |
| 46 |
timer@0 { |
| 47 |
compatible = "atmel,tcb-timer"; |
| 48 |
reg = <0>, <1>; |
| 49 |
}; |
| 50 |
|
| 51 |
timer@2 { |
| 52 |
compatible = "atmel,tcb-timer"; |
| 53 |
reg = <2>; |
| 54 |
}; |
| 55 |
}; |
| 56 |
|
| 57 |
usart0: serial@fffb0000 { |
| 58 |
pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts>; |
| 59 |
linux,rs485-enabled-at-boot-time; |
| 60 |
status = "okay"; |
| 61 |
}; |
| 62 |
|
| 63 |
usart1: serial@fffb4000 { |
| 64 |
pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts>; |
| 65 |
linux,rs485-enabled-at-boot-time; |
| 66 |
status = "okay"; |
| 67 |
}; |
| 68 |
|
| 69 |
usart2: serial@fffb8000 { |
| 70 |
pinctrl-0 = <&pinctrl_usart2>; |
| 71 |
status = "okay"; |
| 72 |
}; |
| 73 |
|
| 74 |
macb0: ethernet@fffc4000 { |
| 75 |
pinctrl-0 = <&pinctrl_macb_rmii &pinctrl_macb_rmii_mii>; |
| 76 |
phy-mode = "mii"; |
| 77 |
status = "okay"; |
| 78 |
}; |
| 79 |
|
| 80 |
mmc0: mmc@fffa8000 { |
| 81 |
pinctrl-0 = <&pinctrl_mmc0_clk |
| 82 |
&pinctrl_mmc0_slot1_cmd_dat0 |
| 83 |
&pinctrl_mmc0_slot1_dat1_3>; |
| 84 |
pinctrl-names = "default"; |
| 85 |
status = "okay"; |
| 86 |
|
| 87 |
slot@1 { |
| 88 |
reg = <1>; |
| 89 |
bus-width = <4>; |
| 90 |
}; |
| 91 |
}; |
| 92 |
|
| 93 |
watchdog@fffffd40 { |
| 94 |
status = "okay"; |
| 95 |
}; |
| 96 |
}; |
| 97 |
|
| 98 |
ebi: ebi@10000000 { |
| 99 |
status = "okay"; |
| 100 |
|
| 101 |
nand_controller: nand-controller { |
| 102 |
status = "okay"; |
| 103 |
pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>; |
| 104 |
pinctrl-names = "default"; |
| 105 |
|
| 106 |
nand@3 { |
| 107 |
reg = <0x3 0x0 0x800000>; |
| 108 |
rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>; |
| 109 |
cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>; |
| 110 |
nand-bus-width = <8>; |
| 111 |
nand-ecc-mode = "soft"; |
| 112 |
nand-on-flash-bbt; |
| 113 |
label = "atmel_nand"; |
| 114 |
|
| 115 |
partitions { |
| 116 |
compatible = "fixed-partitions"; |
| 117 |
#address-cells = <1>; |
| 118 |
#size-cells = <1>; |
| 119 |
|
| 120 |
barebox@0 { |
| 121 |
label = "barebox"; |
| 122 |
reg = <0x0 0x58000>; |
| 123 |
}; |
| 124 |
|
| 125 |
u_boot_env@58000 { |
| 126 |
label = "u_boot_env"; |
| 127 |
reg = <0x58000 0x8000>; |
| 128 |
}; |
| 129 |
|
| 130 |
ubi@60000 { |
| 131 |
label = "ubi"; |
| 132 |
reg = <0x60000 0x1FA0000>; |
| 133 |
}; |
| 134 |
}; |
| 135 |
}; |
| 136 |
}; |
| 137 |
}; |
| 138 |
|
| 139 |
usb0: usb@500000 { |
| 140 |
num-ports = <2>; |
| 141 |
atmel,vbus-gpio = <&pioB 15 GPIO_ACTIVE_LOW>; |
| 142 |
status = "okay"; |
| 143 |
}; |
| 144 |
}; |
| 145 |
|
| 146 |
leds { |
| 147 |
compatible = "gpio-leds"; |
| 148 |
|
| 149 |
led-power-green { |
| 150 |
label = "power_green"; |
| 151 |
gpios = <&pioC 17 GPIO_ACTIVE_HIGH>; |
| 152 |
linux,default-trigger = "heartbeat"; |
| 153 |
}; |
| 154 |
|
| 155 |
led-power-red { |
| 156 |
label = "power_red"; |
| 157 |
gpios = <&pioA 2 GPIO_ACTIVE_HIGH>; |
| 158 |
}; |
| 159 |
|
| 160 |
led-tx-green { |
| 161 |
label = "tx_green"; |
| 162 |
gpios = <&pioC 19 GPIO_ACTIVE_HIGH>; |
| 163 |
}; |
| 164 |
|
| 165 |
led-tx-red { |
| 166 |
label = "tx_red"; |
| 167 |
gpios = <&pioC 18 GPIO_ACTIVE_HIGH>; |
| 168 |
}; |
| 169 |
}; |
| 170 |
|
| 171 |
gpio-keys { |
| 172 |
compatible = "gpio-keys"; |
| 173 |
|
| 174 |
key-switch-in { |
| 175 |
label = "keyswitch_in"; |
| 176 |
gpios = <&pioB 1 GPIO_ACTIVE_HIGH>; |
| 177 |
linux,code = <28>; |
| 178 |
wakeup-source; |
| 179 |
}; |
| 180 |
|
| 181 |
key-error-in { |
| 182 |
label = "error_in"; |
| 183 |
gpios = <&pioB 2 GPIO_ACTIVE_HIGH>; |
| 184 |
linux,code = <29>; |
| 185 |
wakeup-source; |
| 186 |
}; |
| 187 |
|
| 188 |
key-s { |
| 189 |
label = "btn"; |
| 190 |
gpios = <&pioC 23 GPIO_ACTIVE_HIGH>; |
| 191 |
linux,code = <31>; |
| 192 |
wakeup-source; |
| 193 |
}; |
| 194 |
}; |
| 195 |
}; |