| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) |
| 2 |
/* |
| 3 |
* Copyright (C) STMicroelectronics 2019 - All Rights Reserved |
| 4 |
* Author: Alexandre Torgue <[email protected]> for STMicroelectronics. |
| 5 |
*/ |
| 6 |
|
| 7 |
#include <dt-bindings/gpio/gpio.h> |
| 8 |
#include <dt-bindings/leds/common.h> |
| 9 |
#include <dt-bindings/mfd/st,stpmic1.h> |
| 10 |
|
| 11 |
/ { |
| 12 |
aliases { |
| 13 |
serial0 = &uart4; |
| 14 |
serial1 = &usart3; |
| 15 |
serial2 = &uart7; |
| 16 |
}; |
| 17 |
|
| 18 |
memory@c0000000 { |
| 19 |
device_type = "memory"; |
| 20 |
reg = <0xc0000000 0x20000000>; |
| 21 |
}; |
| 22 |
|
| 23 |
reserved-memory { |
| 24 |
#address-cells = <1>; |
| 25 |
#size-cells = <1>; |
| 26 |
ranges; |
| 27 |
|
| 28 |
mcuram2: mcuram2@10000000 { |
| 29 |
compatible = "shared-dma-pool"; |
| 30 |
reg = <0x10000000 0x40000>; |
| 31 |
no-map; |
| 32 |
}; |
| 33 |
|
| 34 |
vdev0vring0: vdev0vring0@10040000 { |
| 35 |
compatible = "shared-dma-pool"; |
| 36 |
reg = <0x10040000 0x1000>; |
| 37 |
no-map; |
| 38 |
}; |
| 39 |
|
| 40 |
vdev0vring1: vdev0vring1@10041000 { |
| 41 |
compatible = "shared-dma-pool"; |
| 42 |
reg = <0x10041000 0x1000>; |
| 43 |
no-map; |
| 44 |
}; |
| 45 |
|
| 46 |
vdev0buffer: vdev0buffer@10042000 { |
| 47 |
compatible = "shared-dma-pool"; |
| 48 |
reg = <0x10042000 0x4000>; |
| 49 |
no-map; |
| 50 |
}; |
| 51 |
|
| 52 |
mcuram: mcuram@30000000 { |
| 53 |
compatible = "shared-dma-pool"; |
| 54 |
reg = <0x30000000 0x40000>; |
| 55 |
no-map; |
| 56 |
}; |
| 57 |
|
| 58 |
retram: retram@38000000 { |
| 59 |
compatible = "shared-dma-pool"; |
| 60 |
reg = <0x38000000 0x10000>; |
| 61 |
no-map; |
| 62 |
}; |
| 63 |
}; |
| 64 |
|
| 65 |
led { |
| 66 |
compatible = "gpio-leds"; |
| 67 |
led_blue: led-blue { |
| 68 |
function = LED_FUNCTION_HEARTBEAT; |
| 69 |
color = <LED_COLOR_ID_BLUE>; |
| 70 |
gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>; |
| 71 |
linux,default-trigger = "heartbeat"; |
| 72 |
default-state = "off"; |
| 73 |
}; |
| 74 |
|
| 75 |
led-red { |
| 76 |
function = LED_FUNCTION_STATUS; |
| 77 |
color = <LED_COLOR_ID_RED>; |
| 78 |
gpios = <&gpioa 13 GPIO_ACTIVE_LOW>; |
| 79 |
}; |
| 80 |
}; |
| 81 |
|
| 82 |
options { |
| 83 |
u-boot { |
| 84 |
compatible = "u-boot,config"; |
| 85 |
boot-led = <&led_blue>; |
| 86 |
}; |
| 87 |
}; |
| 88 |
|
| 89 |
sound { |
| 90 |
compatible = "audio-graph-card"; |
| 91 |
label = "STM32MP15-DK"; |
| 92 |
routing = |
| 93 |
"Playback" , "MCLK", |
| 94 |
"Capture" , "MCLK", |
| 95 |
"MICL" , "Mic Bias"; |
| 96 |
dais = <&sai2a_port &sai2b_port &i2s2_port>; |
| 97 |
status = "okay"; |
| 98 |
}; |
| 99 |
|
| 100 |
vin: vin { |
| 101 |
compatible = "regulator-fixed"; |
| 102 |
regulator-name = "vin"; |
| 103 |
regulator-min-microvolt = <5000000>; |
| 104 |
regulator-max-microvolt = <5000000>; |
| 105 |
regulator-always-on; |
| 106 |
}; |
| 107 |
}; |
| 108 |
|
| 109 |
&adc { |
| 110 |
pinctrl-names = "default"; |
| 111 |
pinctrl-0 = <&adc12_usb_cc_pins_a>; |
| 112 |
vdd-supply = <&vdd>; |
| 113 |
vdda-supply = <&vdd>; |
| 114 |
vref-supply = <&vrefbuf>; |
| 115 |
status = "okay"; |
| 116 |
adc1: adc@0 { |
| 117 |
status = "okay"; |
| 118 |
/* |
| 119 |
* Type-C USB_PWR_CC1 & USB_PWR_CC2 on in18 & in19. |
| 120 |
* Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C: |
| 121 |
* 5 * (56 + 47kOhms) * 5pF => 2.5us. |
| 122 |
* Use arbitrary margin here (e.g. 5us). |
| 123 |
*/ |
| 124 |
channel@18 { |
| 125 |
reg = <18>; |
| 126 |
st,min-sample-time-ns = <5000>; |
| 127 |
}; |
| 128 |
channel@19 { |
| 129 |
reg = <19>; |
| 130 |
st,min-sample-time-ns = <5000>; |
| 131 |
}; |
| 132 |
}; |
| 133 |
adc2: adc@100 { |
| 134 |
status = "okay"; |
| 135 |
/* USB Type-C CC1 & CC2 */ |
| 136 |
channel@18 { |
| 137 |
reg = <18>; |
| 138 |
st,min-sample-time-ns = <5000>; |
| 139 |
}; |
| 140 |
channel@19 { |
| 141 |
reg = <19>; |
| 142 |
st,min-sample-time-ns = <5000>; |
| 143 |
}; |
| 144 |
}; |
| 145 |
}; |
| 146 |
|
| 147 |
&cec { |
| 148 |
pinctrl-names = "default", "sleep"; |
| 149 |
pinctrl-0 = <&cec_pins_b>; |
| 150 |
pinctrl-1 = <&cec_sleep_pins_b>; |
| 151 |
status = "okay"; |
| 152 |
}; |
| 153 |
|
| 154 |
&crc1 { |
| 155 |
status = "okay"; |
| 156 |
}; |
| 157 |
|
| 158 |
&dts { |
| 159 |
status = "okay"; |
| 160 |
}; |
| 161 |
|
| 162 |
ðernet0 { |
| 163 |
status = "okay"; |
| 164 |
pinctrl-0 = <ðernet0_rgmii_pins_a>; |
| 165 |
pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>; |
| 166 |
pinctrl-names = "default", "sleep"; |
| 167 |
phy-mode = "rgmii-id"; |
| 168 |
max-speed = <1000>; |
| 169 |
phy-handle = <&phy0>; |
| 170 |
|
| 171 |
mdio { |
| 172 |
#address-cells = <1>; |
| 173 |
#size-cells = <0>; |
| 174 |
compatible = "snps,dwmac-mdio"; |
| 175 |
phy0: ethernet-phy@0 { |
| 176 |
reg = <0>; |
| 177 |
}; |
| 178 |
}; |
| 179 |
}; |
| 180 |
|
| 181 |
&hash1 { |
| 182 |
status = "okay"; |
| 183 |
}; |
| 184 |
|
| 185 |
&i2c1 { |
| 186 |
pinctrl-names = "default", "sleep"; |
| 187 |
pinctrl-0 = <&i2c1_pins_a>; |
| 188 |
pinctrl-1 = <&i2c1_sleep_pins_a>; |
| 189 |
i2c-scl-rising-time-ns = <100>; |
| 190 |
i2c-scl-falling-time-ns = <7>; |
| 191 |
status = "okay"; |
| 192 |
/delete-property/dmas; |
| 193 |
/delete-property/dma-names; |
| 194 |
|
| 195 |
hdmi-transmitter@39 { |
| 196 |
compatible = "sil,sii9022"; |
| 197 |
reg = <0x39>; |
| 198 |
iovcc-supply = <&v3v3_hdmi>; |
| 199 |
cvcc12-supply = <&v1v2_hdmi>; |
| 200 |
reset-gpios = <&gpioa 10 GPIO_ACTIVE_LOW>; |
| 201 |
interrupts = <1 IRQ_TYPE_EDGE_FALLING>; |
| 202 |
interrupt-parent = <&gpiog>; |
| 203 |
#sound-dai-cells = <0>; |
| 204 |
status = "okay"; |
| 205 |
|
| 206 |
ports { |
| 207 |
#address-cells = <1>; |
| 208 |
#size-cells = <0>; |
| 209 |
|
| 210 |
port@0 { |
| 211 |
reg = <0>; |
| 212 |
sii9022_in: endpoint { |
| 213 |
remote-endpoint = <<dc_ep0_out>; |
| 214 |
}; |
| 215 |
}; |
| 216 |
|
| 217 |
port@3 { |
| 218 |
reg = <3>; |
| 219 |
sii9022_tx_endpoint: endpoint { |
| 220 |
remote-endpoint = <&i2s2_endpoint>; |
| 221 |
}; |
| 222 |
}; |
| 223 |
}; |
| 224 |
}; |
| 225 |
|
| 226 |
cs42l51: cs42l51@4a { |
| 227 |
compatible = "cirrus,cs42l51"; |
| 228 |
reg = <0x4a>; |
| 229 |
#sound-dai-cells = <0>; |
| 230 |
VL-supply = <&v3v3>; |
| 231 |
VD-supply = <&v1v8_audio>; |
| 232 |
VA-supply = <&v1v8_audio>; |
| 233 |
VAHP-supply = <&v1v8_audio>; |
| 234 |
reset-gpios = <&gpiog 9 GPIO_ACTIVE_LOW>; |
| 235 |
clocks = <&sai2a>; |
| 236 |
clock-names = "MCLK"; |
| 237 |
status = "okay"; |
| 238 |
|
| 239 |
cs42l51_port: port { |
| 240 |
#address-cells = <1>; |
| 241 |
#size-cells = <0>; |
| 242 |
|
| 243 |
cs42l51_tx_endpoint: endpoint@0 { |
| 244 |
reg = <0>; |
| 245 |
remote-endpoint = <&sai2a_endpoint>; |
| 246 |
frame-master = <&cs42l51_tx_endpoint>; |
| 247 |
bitclock-master = <&cs42l51_tx_endpoint>; |
| 248 |
}; |
| 249 |
|
| 250 |
cs42l51_rx_endpoint: endpoint@1 { |
| 251 |
reg = <1>; |
| 252 |
remote-endpoint = <&sai2b_endpoint>; |
| 253 |
frame-master = <&cs42l51_rx_endpoint>; |
| 254 |
bitclock-master = <&cs42l51_rx_endpoint>; |
| 255 |
}; |
| 256 |
}; |
| 257 |
}; |
| 258 |
}; |
| 259 |
|
| 260 |
&i2c4 { |
| 261 |
pinctrl-names = "default", "sleep"; |
| 262 |
pinctrl-0 = <&i2c4_pins_a>; |
| 263 |
pinctrl-1 = <&i2c4_sleep_pins_a>; |
| 264 |
i2c-scl-rising-time-ns = <185>; |
| 265 |
i2c-scl-falling-time-ns = <20>; |
| 266 |
clock-frequency = <400000>; |
| 267 |
status = "okay"; |
| 268 |
/* spare dmas for other usage */ |
| 269 |
/delete-property/dmas; |
| 270 |
/delete-property/dma-names; |
| 271 |
|
| 272 |
stusb1600: typec@28 { |
| 273 |
compatible = "st,stusb1600"; |
| 274 |
reg = <0x28>; |
| 275 |
interrupts = <11 IRQ_TYPE_LEVEL_LOW>; |
| 276 |
interrupt-parent = <&gpioi>; |
| 277 |
pinctrl-names = "default"; |
| 278 |
pinctrl-0 = <&stusb1600_pins_a>; |
| 279 |
status = "okay"; |
| 280 |
vdd-supply = <&vin>; |
| 281 |
|
| 282 |
connector { |
| 283 |
compatible = "usb-c-connector"; |
| 284 |
label = "USB-C"; |
| 285 |
power-role = "dual"; |
| 286 |
typec-power-opmode = "default"; |
| 287 |
|
| 288 |
port { |
| 289 |
con_usbotg_hs_ep: endpoint { |
| 290 |
remote-endpoint = <&usbotg_hs_ep>; |
| 291 |
}; |
| 292 |
}; |
| 293 |
}; |
| 294 |
}; |
| 295 |
|
| 296 |
pmic: stpmic@33 { |
| 297 |
compatible = "st,stpmic1"; |
| 298 |
reg = <0x33>; |
| 299 |
interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; |
| 300 |
interrupt-controller; |
| 301 |
#interrupt-cells = <2>; |
| 302 |
status = "okay"; |
| 303 |
|
| 304 |
regulators { |
| 305 |
compatible = "st,stpmic1-regulators"; |
| 306 |
buck1-supply = <&vin>; |
| 307 |
buck2-supply = <&vin>; |
| 308 |
buck3-supply = <&vin>; |
| 309 |
buck4-supply = <&vin>; |
| 310 |
ldo1-supply = <&v3v3>; |
| 311 |
ldo2-supply = <&vin>; |
| 312 |
ldo3-supply = <&vdd_ddr>; |
| 313 |
ldo4-supply = <&vin>; |
| 314 |
ldo5-supply = <&vin>; |
| 315 |
ldo6-supply = <&v3v3>; |
| 316 |
vref_ddr-supply = <&vin>; |
| 317 |
boost-supply = <&vin>; |
| 318 |
pwr_sw1-supply = <&bst_out>; |
| 319 |
pwr_sw2-supply = <&bst_out>; |
| 320 |
|
| 321 |
vddcore: buck1 { |
| 322 |
regulator-name = "vddcore"; |
| 323 |
regulator-min-microvolt = <1200000>; |
| 324 |
regulator-max-microvolt = <1350000>; |
| 325 |
regulator-always-on; |
| 326 |
regulator-initial-mode = <0>; |
| 327 |
regulator-over-current-protection; |
| 328 |
}; |
| 329 |
|
| 330 |
vdd_ddr: buck2 { |
| 331 |
regulator-name = "vdd_ddr"; |
| 332 |
regulator-min-microvolt = <1350000>; |
| 333 |
regulator-max-microvolt = <1350000>; |
| 334 |
regulator-always-on; |
| 335 |
regulator-initial-mode = <0>; |
| 336 |
regulator-over-current-protection; |
| 337 |
}; |
| 338 |
|
| 339 |
vdd: buck3 { |
| 340 |
regulator-name = "vdd"; |
| 341 |
regulator-min-microvolt = <3300000>; |
| 342 |
regulator-max-microvolt = <3300000>; |
| 343 |
regulator-always-on; |
| 344 |
st,mask-reset; |
| 345 |
regulator-initial-mode = <0>; |
| 346 |
regulator-over-current-protection; |
| 347 |
}; |
| 348 |
|
| 349 |
v3v3: buck4 { |
| 350 |
regulator-name = "v3v3"; |
| 351 |
regulator-min-microvolt = <3300000>; |
| 352 |
regulator-max-microvolt = <3300000>; |
| 353 |
regulator-always-on; |
| 354 |
regulator-over-current-protection; |
| 355 |
regulator-initial-mode = <0>; |
| 356 |
}; |
| 357 |
|
| 358 |
v1v8_audio: ldo1 { |
| 359 |
regulator-name = "v1v8_audio"; |
| 360 |
regulator-min-microvolt = <1800000>; |
| 361 |
regulator-max-microvolt = <1800000>; |
| 362 |
regulator-always-on; |
| 363 |
interrupts = <IT_CURLIM_LDO1 0>; |
| 364 |
}; |
| 365 |
|
| 366 |
v3v3_hdmi: ldo2 { |
| 367 |
regulator-name = "v3v3_hdmi"; |
| 368 |
regulator-min-microvolt = <3300000>; |
| 369 |
regulator-max-microvolt = <3300000>; |
| 370 |
regulator-always-on; |
| 371 |
interrupts = <IT_CURLIM_LDO2 0>; |
| 372 |
}; |
| 373 |
|
| 374 |
vtt_ddr: ldo3 { |
| 375 |
regulator-name = "vtt_ddr"; |
| 376 |
regulator-min-microvolt = <500000>; |
| 377 |
regulator-max-microvolt = <750000>; |
| 378 |
regulator-always-on; |
| 379 |
regulator-over-current-protection; |
| 380 |
}; |
| 381 |
|
| 382 |
vdd_usb: ldo4 { |
| 383 |
regulator-name = "vdd_usb"; |
| 384 |
interrupts = <IT_CURLIM_LDO4 0>; |
| 385 |
}; |
| 386 |
|
| 387 |
vdda: ldo5 { |
| 388 |
regulator-name = "vdda"; |
| 389 |
regulator-min-microvolt = <2900000>; |
| 390 |
regulator-max-microvolt = <2900000>; |
| 391 |
interrupts = <IT_CURLIM_LDO5 0>; |
| 392 |
regulator-boot-on; |
| 393 |
}; |
| 394 |
|
| 395 |
v1v2_hdmi: ldo6 { |
| 396 |
regulator-name = "v1v2_hdmi"; |
| 397 |
regulator-min-microvolt = <1200000>; |
| 398 |
regulator-max-microvolt = <1200000>; |
| 399 |
regulator-always-on; |
| 400 |
interrupts = <IT_CURLIM_LDO6 0>; |
| 401 |
}; |
| 402 |
|
| 403 |
vref_ddr: vref_ddr { |
| 404 |
regulator-name = "vref_ddr"; |
| 405 |
regulator-always-on; |
| 406 |
}; |
| 407 |
|
| 408 |
bst_out: boost { |
| 409 |
regulator-name = "bst_out"; |
| 410 |
interrupts = <IT_OCP_BOOST 0>; |
| 411 |
}; |
| 412 |
|
| 413 |
vbus_otg: pwr_sw1 { |
| 414 |
regulator-name = "vbus_otg"; |
| 415 |
interrupts = <IT_OCP_OTG 0>; |
| 416 |
}; |
| 417 |
|
| 418 |
vbus_sw: pwr_sw2 { |
| 419 |
regulator-name = "vbus_sw"; |
| 420 |
interrupts = <IT_OCP_SWOUT 0>; |
| 421 |
regulator-active-discharge = <1>; |
| 422 |
}; |
| 423 |
}; |
| 424 |
|
| 425 |
onkey { |
| 426 |
compatible = "st,stpmic1-onkey"; |
| 427 |
interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>; |
| 428 |
interrupt-names = "onkey-falling", "onkey-rising"; |
| 429 |
power-off-time-sec = <10>; |
| 430 |
status = "okay"; |
| 431 |
}; |
| 432 |
|
| 433 |
watchdog { |
| 434 |
compatible = "st,stpmic1-wdt"; |
| 435 |
status = "disabled"; |
| 436 |
}; |
| 437 |
}; |
| 438 |
}; |
| 439 |
|
| 440 |
&i2c5 { |
| 441 |
pinctrl-names = "default", "sleep"; |
| 442 |
pinctrl-0 = <&i2c5_pins_a>; |
| 443 |
pinctrl-1 = <&i2c5_sleep_pins_a>; |
| 444 |
i2c-scl-rising-time-ns = <185>; |
| 445 |
i2c-scl-falling-time-ns = <20>; |
| 446 |
clock-frequency = <400000>; |
| 447 |
/* spare dmas for other usage */ |
| 448 |
/delete-property/dmas; |
| 449 |
/delete-property/dma-names; |
| 450 |
status = "disabled"; |
| 451 |
}; |
| 452 |
|
| 453 |
&i2s2 { |
| 454 |
clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>; |
| 455 |
clock-names = "pclk", "i2sclk", "x8k", "x11k"; |
| 456 |
pinctrl-names = "default", "sleep"; |
| 457 |
pinctrl-0 = <&i2s2_pins_a>; |
| 458 |
pinctrl-1 = <&i2s2_sleep_pins_a>; |
| 459 |
status = "okay"; |
| 460 |
|
| 461 |
i2s2_port: port { |
| 462 |
i2s2_endpoint: endpoint { |
| 463 |
remote-endpoint = <&sii9022_tx_endpoint>; |
| 464 |
dai-format = "i2s"; |
| 465 |
mclk-fs = <256>; |
| 466 |
}; |
| 467 |
}; |
| 468 |
}; |
| 469 |
|
| 470 |
&ipcc { |
| 471 |
status = "okay"; |
| 472 |
}; |
| 473 |
|
| 474 |
&iwdg2 { |
| 475 |
timeout-sec = <32>; |
| 476 |
status = "okay"; |
| 477 |
}; |
| 478 |
|
| 479 |
<dc { |
| 480 |
pinctrl-names = "default", "sleep"; |
| 481 |
pinctrl-0 = <<dc_pins_a>; |
| 482 |
pinctrl-1 = <<dc_sleep_pins_a>; |
| 483 |
status = "okay"; |
| 484 |
|
| 485 |
port { |
| 486 |
ltdc_ep0_out: endpoint { |
| 487 |
remote-endpoint = <&sii9022_in>; |
| 488 |
}; |
| 489 |
}; |
| 490 |
}; |
| 491 |
|
| 492 |
&m4_rproc { |
| 493 |
memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>, |
| 494 |
<&vdev0vring1>, <&vdev0buffer>; |
| 495 |
mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>; |
| 496 |
mbox-names = "vq0", "vq1", "shutdown", "detach"; |
| 497 |
pinctrl-names = "default"; |
| 498 |
pinctrl-0 = <&m4_leds_orange_pins_a>; |
| 499 |
interrupt-parent = <&exti>; |
| 500 |
interrupts = <68 1>; |
| 501 |
status = "okay"; |
| 502 |
}; |
| 503 |
|
| 504 |
&pwr_regulators { |
| 505 |
vdd-supply = <&vdd>; |
| 506 |
vdd_3v3_usbfs-supply = <&vdd_usb>; |
| 507 |
}; |
| 508 |
|
| 509 |
&rng1 { |
| 510 |
status = "okay"; |
| 511 |
}; |
| 512 |
|
| 513 |
&rtc { |
| 514 |
status = "okay"; |
| 515 |
}; |
| 516 |
|
| 517 |
&sai2 { |
| 518 |
clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>; |
| 519 |
clock-names = "pclk", "x8k", "x11k"; |
| 520 |
pinctrl-names = "default", "sleep"; |
| 521 |
pinctrl-0 = <&sai2a_pins_a>, <&sai2b_pins_b>; |
| 522 |
pinctrl-1 = <&sai2a_sleep_pins_a>, <&sai2b_sleep_pins_b>; |
| 523 |
status = "okay"; |
| 524 |
|
| 525 |
sai2a: audio-controller@4400b004 { |
| 526 |
#clock-cells = <0>; |
| 527 |
dma-names = "tx"; |
| 528 |
status = "okay"; |
| 529 |
|
| 530 |
sai2a_port: port { |
| 531 |
sai2a_endpoint: endpoint { |
| 532 |
remote-endpoint = <&cs42l51_tx_endpoint>; |
| 533 |
dai-format = "i2s"; |
| 534 |
mclk-fs = <256>; |
| 535 |
system-clock-direction-out; |
| 536 |
dai-tdm-slot-num = <2>; |
| 537 |
dai-tdm-slot-width = <32>; |
| 538 |
}; |
| 539 |
}; |
| 540 |
}; |
| 541 |
|
| 542 |
sai2b: audio-controller@4400b024 { |
| 543 |
dma-names = "rx"; |
| 544 |
st,sync = <&sai2a 2>; |
| 545 |
clocks = <&rcc SAI2_K>, <&sai2a>; |
| 546 |
clock-names = "sai_ck", "MCLK"; |
| 547 |
status = "okay"; |
| 548 |
|
| 549 |
sai2b_port: port { |
| 550 |
sai2b_endpoint: endpoint { |
| 551 |
remote-endpoint = <&cs42l51_rx_endpoint>; |
| 552 |
dai-format = "i2s"; |
| 553 |
mclk-fs = <256>; |
| 554 |
dai-tdm-slot-num = <2>; |
| 555 |
dai-tdm-slot-width = <32>; |
| 556 |
}; |
| 557 |
}; |
| 558 |
}; |
| 559 |
}; |
| 560 |
|
| 561 |
&sdmmc1 { |
| 562 |
pinctrl-names = "default", "opendrain", "sleep"; |
| 563 |
pinctrl-0 = <&sdmmc1_b4_pins_a>; |
| 564 |
pinctrl-1 = <&sdmmc1_b4_od_pins_a>; |
| 565 |
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; |
| 566 |
cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; |
| 567 |
disable-wp; |
| 568 |
st,neg-edge; |
| 569 |
bus-width = <4>; |
| 570 |
vmmc-supply = <&v3v3>; |
| 571 |
status = "okay"; |
| 572 |
}; |
| 573 |
|
| 574 |
&sdmmc3 { |
| 575 |
pinctrl-names = "default", "opendrain", "sleep"; |
| 576 |
pinctrl-0 = <&sdmmc3_b4_pins_a>; |
| 577 |
pinctrl-1 = <&sdmmc3_b4_od_pins_a>; |
| 578 |
pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>; |
| 579 |
broken-cd; |
| 580 |
st,neg-edge; |
| 581 |
bus-width = <4>; |
| 582 |
vmmc-supply = <&v3v3>; |
| 583 |
status = "disabled"; |
| 584 |
}; |
| 585 |
|
| 586 |
&timers1 { |
| 587 |
/* spare dmas for other usage */ |
| 588 |
/delete-property/dmas; |
| 589 |
/delete-property/dma-names; |
| 590 |
status = "disabled"; |
| 591 |
counter { |
| 592 |
status = "okay"; |
| 593 |
}; |
| 594 |
pwm { |
| 595 |
pinctrl-0 = <&pwm1_pins_a>; |
| 596 |
pinctrl-1 = <&pwm1_sleep_pins_a>; |
| 597 |
pinctrl-names = "default", "sleep"; |
| 598 |
status = "okay"; |
| 599 |
}; |
| 600 |
timer@0 { |
| 601 |
status = "okay"; |
| 602 |
}; |
| 603 |
}; |
| 604 |
|
| 605 |
&timers3 { |
| 606 |
/delete-property/dmas; |
| 607 |
/delete-property/dma-names; |
| 608 |
status = "disabled"; |
| 609 |
counter { |
| 610 |
status = "okay"; |
| 611 |
}; |
| 612 |
pwm { |
| 613 |
pinctrl-0 = <&pwm3_pins_a>; |
| 614 |
pinctrl-1 = <&pwm3_sleep_pins_a>; |
| 615 |
pinctrl-names = "default", "sleep"; |
| 616 |
status = "okay"; |
| 617 |
}; |
| 618 |
timer@2 { |
| 619 |
status = "okay"; |
| 620 |
}; |
| 621 |
}; |
| 622 |
|
| 623 |
&timers4 { |
| 624 |
/delete-property/dmas; |
| 625 |
/delete-property/dma-names; |
| 626 |
status = "disabled"; |
| 627 |
counter { |
| 628 |
status = "okay"; |
| 629 |
}; |
| 630 |
pwm { |
| 631 |
pinctrl-0 = <&pwm4_pins_a &pwm4_pins_b>; |
| 632 |
pinctrl-1 = <&pwm4_sleep_pins_a &pwm4_sleep_pins_b>; |
| 633 |
pinctrl-names = "default", "sleep"; |
| 634 |
status = "okay"; |
| 635 |
}; |
| 636 |
timer@3 { |
| 637 |
status = "okay"; |
| 638 |
}; |
| 639 |
}; |
| 640 |
|
| 641 |
&timers5 { |
| 642 |
/delete-property/dmas; |
| 643 |
/delete-property/dma-names; |
| 644 |
status = "disabled"; |
| 645 |
counter { |
| 646 |
status = "okay"; |
| 647 |
}; |
| 648 |
pwm { |
| 649 |
pinctrl-0 = <&pwm5_pins_a>; |
| 650 |
pinctrl-1 = <&pwm5_sleep_pins_a>; |
| 651 |
pinctrl-names = "default", "sleep"; |
| 652 |
status = "okay"; |
| 653 |
}; |
| 654 |
timer@4 { |
| 655 |
status = "okay"; |
| 656 |
}; |
| 657 |
}; |
| 658 |
|
| 659 |
&timers6 { |
| 660 |
/delete-property/dmas; |
| 661 |
/delete-property/dma-names; |
| 662 |
status = "disabled"; |
| 663 |
counter { |
| 664 |
status = "okay"; |
| 665 |
}; |
| 666 |
timer@5 { |
| 667 |
status = "okay"; |
| 668 |
}; |
| 669 |
}; |
| 670 |
|
| 671 |
&timers12 { |
| 672 |
/delete-property/dmas; |
| 673 |
/delete-property/dma-names; |
| 674 |
status = "disabled"; |
| 675 |
counter { |
| 676 |
status = "okay"; |
| 677 |
}; |
| 678 |
pwm { |
| 679 |
pinctrl-0 = <&pwm12_pins_a>; |
| 680 |
pinctrl-1 = <&pwm12_sleep_pins_a>; |
| 681 |
pinctrl-names = "default", "sleep"; |
| 682 |
status = "okay"; |
| 683 |
}; |
| 684 |
timer@11 { |
| 685 |
status = "okay"; |
| 686 |
}; |
| 687 |
}; |
| 688 |
|
| 689 |
&uart4 { |
| 690 |
pinctrl-names = "default", "sleep", "idle"; |
| 691 |
pinctrl-0 = <&uart4_pins_a>; |
| 692 |
pinctrl-1 = <&uart4_sleep_pins_a>; |
| 693 |
pinctrl-2 = <&uart4_idle_pins_a>; |
| 694 |
/delete-property/dmas; |
| 695 |
/delete-property/dma-names; |
| 696 |
status = "okay"; |
| 697 |
}; |
| 698 |
|
| 699 |
&uart7 { |
| 700 |
pinctrl-names = "default", "sleep", "idle"; |
| 701 |
pinctrl-0 = <&uart7_pins_c>; |
| 702 |
pinctrl-1 = <&uart7_sleep_pins_c>; |
| 703 |
pinctrl-2 = <&uart7_idle_pins_c>; |
| 704 |
/delete-property/dmas; |
| 705 |
/delete-property/dma-names; |
| 706 |
status = "disabled"; |
| 707 |
}; |
| 708 |
|
| 709 |
&usart3 { |
| 710 |
pinctrl-names = "default", "sleep", "idle"; |
| 711 |
pinctrl-0 = <&usart3_pins_c>; |
| 712 |
pinctrl-1 = <&usart3_sleep_pins_c>; |
| 713 |
pinctrl-2 = <&usart3_idle_pins_c>; |
| 714 |
uart-has-rtscts; |
| 715 |
status = "disabled"; |
| 716 |
}; |
| 717 |
|
| 718 |
&usbh_ehci { |
| 719 |
status = "okay"; |
| 720 |
#address-cells = <1>; |
| 721 |
#size-cells = <0>; |
| 722 |
/* onboard HUB */ |
| 723 |
hub@1 { |
| 724 |
compatible = "usb424,2514"; |
| 725 |
reg = <1>; |
| 726 |
vdd-supply = <&v3v3>; |
| 727 |
}; |
| 728 |
}; |
| 729 |
|
| 730 |
&usbotg_hs { |
| 731 |
phys = <&usbphyc_port1 0>; |
| 732 |
phy-names = "usb2-phy"; |
| 733 |
usb-role-switch; |
| 734 |
status = "okay"; |
| 735 |
|
| 736 |
port { |
| 737 |
usbotg_hs_ep: endpoint { |
| 738 |
remote-endpoint = <&con_usbotg_hs_ep>; |
| 739 |
}; |
| 740 |
}; |
| 741 |
}; |
| 742 |
|
| 743 |
&usbphyc { |
| 744 |
status = "okay"; |
| 745 |
}; |
| 746 |
|
| 747 |
&usbphyc_port0 { |
| 748 |
phy-supply = <&vdd_usb>; |
| 749 |
st,tune-hs-dc-level = <2>; |
| 750 |
st,enable-fs-rftime-tuning; |
| 751 |
st,enable-hs-rftime-reduction; |
| 752 |
st,trim-hs-current = <15>; |
| 753 |
st,trim-hs-impedance = <1>; |
| 754 |
st,tune-squelch-level = <3>; |
| 755 |
st,tune-hs-rx-offset = <2>; |
| 756 |
st,no-lsfs-sc; |
| 757 |
}; |
| 758 |
|
| 759 |
&usbphyc_port1 { |
| 760 |
phy-supply = <&vdd_usb>; |
| 761 |
st,tune-hs-dc-level = <2>; |
| 762 |
st,enable-fs-rftime-tuning; |
| 763 |
st,enable-hs-rftime-reduction; |
| 764 |
st,trim-hs-current = <15>; |
| 765 |
st,trim-hs-impedance = <1>; |
| 766 |
st,tune-squelch-level = <3>; |
| 767 |
st,tune-hs-rx-offset = <2>; |
| 768 |
st,no-lsfs-sc; |
| 769 |
}; |
| 770 |
|
| 771 |
&vrefbuf { |
| 772 |
regulator-min-microvolt = <2500000>; |
| 773 |
regulator-max-microvolt = <2500000>; |
| 774 |
vdda-supply = <&vdd>; |
| 775 |
status = "okay"; |
| 776 |
}; |