| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) |
| 2 |
/dts-v1/; |
| 3 |
|
| 4 |
#include <arm/st/stm32mp151.dtsi> |
| 5 |
#include <arm/st/stm32mp15xc.dtsi> |
| 6 |
#include <arm/st/stm32mp15-pinctrl.dtsi> |
| 7 |
#include <arm/st/stm32mp15xxad-pinctrl.dtsi> |
| 8 |
#include <arm/st/stm32mp15-scmi.dtsi> |
| 9 |
#include <dt-bindings/gpio/gpio.h> |
| 10 |
#include <dt-bindings/leds/common.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
model = "Plymovent AQM board"; |
| 14 |
compatible = "ply,plyaqm", "st,stm32mp151"; |
| 15 |
|
| 16 |
aliases { |
| 17 |
ethernet0 = ðernet0; |
| 18 |
serial0 = &uart4; |
| 19 |
serial1 = &uart7; |
| 20 |
}; |
| 21 |
|
| 22 |
codec { |
| 23 |
compatible = "invensense,ics43432"; |
| 24 |
|
| 25 |
port { |
| 26 |
codec_endpoint: endpoint { |
| 27 |
remote-endpoint = <&i2s1_endpoint>; |
| 28 |
dai-format = "i2s"; |
| 29 |
}; |
| 30 |
}; |
| 31 |
}; |
| 32 |
|
| 33 |
firmware { |
| 34 |
optee { |
| 35 |
compatible = "linaro,optee-tz"; |
| 36 |
method = "smc"; |
| 37 |
}; |
| 38 |
}; |
| 39 |
|
| 40 |
leds { |
| 41 |
compatible = "gpio-leds"; |
| 42 |
|
| 43 |
led-0 { |
| 44 |
gpios = <&gpioa 3 GPIO_ACTIVE_HIGH>; /* WHITE_EN */ |
| 45 |
color = <LED_COLOR_ID_WHITE>; |
| 46 |
default-state = "on"; |
| 47 |
}; |
| 48 |
}; |
| 49 |
|
| 50 |
v3v3: fixed-regulator-v3v3 { |
| 51 |
compatible = "regulator-fixed"; |
| 52 |
regulator-name = "v3v3"; |
| 53 |
regulator-min-microvolt = <3300000>; |
| 54 |
regulator-max-microvolt = <3300000>; |
| 55 |
}; |
| 56 |
|
| 57 |
v5v_sw: fixed-regulator-v5sw { |
| 58 |
compatible = "regulator-fixed"; |
| 59 |
regulator-name = "5v-switched"; |
| 60 |
regulator-min-microvolt = <5000000>; |
| 61 |
regulator-max-microvolt = <5000000>; |
| 62 |
gpio = <&gpioe 10 GPIO_ACTIVE_HIGH>; /* 5V_SWITCHED_EN */ |
| 63 |
startup-delay-us = <100000>; |
| 64 |
enable-active-high; |
| 65 |
regulator-boot-on; |
| 66 |
}; |
| 67 |
|
| 68 |
reserved-memory { |
| 69 |
#address-cells = <1>; |
| 70 |
#size-cells = <1>; |
| 71 |
ranges; |
| 72 |
|
| 73 |
optee@cfd00000 { |
| 74 |
reg = <0xcfd00000 0x300000>; |
| 75 |
no-map; |
| 76 |
}; |
| 77 |
}; |
| 78 |
|
| 79 |
sound { |
| 80 |
compatible = "audio-graph-card"; |
| 81 |
label = "STM32MP15"; |
| 82 |
dais = <&i2s1_port>; |
| 83 |
}; |
| 84 |
|
| 85 |
wifi_pwrseq: wifi-pwrseq { |
| 86 |
compatible = "mmc-pwrseq-simple"; |
| 87 |
reset-gpios = <&gpioe 12 GPIO_ACTIVE_LOW>; /* WLAN_REG_ON */ |
| 88 |
}; |
| 89 |
}; |
| 90 |
|
| 91 |
&adc { |
| 92 |
pinctrl-names = "default"; |
| 93 |
pinctrl-0 = <&adc1_in10_pins_a>; |
| 94 |
vdda-supply = <&v3v3>; |
| 95 |
vref-supply = <&v3v3>; |
| 96 |
status = "okay"; |
| 97 |
|
| 98 |
adc@0 { |
| 99 |
#address-cells = <1>; |
| 100 |
#size-cells = <0>; |
| 101 |
status = "okay"; |
| 102 |
|
| 103 |
channel@10 { /* NTC */ |
| 104 |
reg = <10>; |
| 105 |
st,min-sample-time-ns = <10000>; /* 10µs sampling time */ |
| 106 |
}; |
| 107 |
}; |
| 108 |
}; |
| 109 |
|
| 110 |
&cpu0 { |
| 111 |
clocks = <&scmi_clk CK_SCMI_MPU>; |
| 112 |
}; |
| 113 |
|
| 114 |
&cryp1 { |
| 115 |
clocks = <&scmi_clk CK_SCMI_CRYP1>; |
| 116 |
resets = <&scmi_reset RST_SCMI_CRYP1>; |
| 117 |
status = "okay"; |
| 118 |
}; |
| 119 |
|
| 120 |
ðernet0 { |
| 121 |
pinctrl-names = "default", "sleep"; |
| 122 |
pinctrl-0 = <ðernet0_rmii_pins_d>; |
| 123 |
pinctrl-1 = <ðernet0_rmii_sleep_pins_d>; |
| 124 |
phy-mode = "rmii"; |
| 125 |
max-speed = <100>; |
| 126 |
phy-handle = <ðphy0>; |
| 127 |
status = "okay"; |
| 128 |
|
| 129 |
mdio { |
| 130 |
#address-cells = <1>; |
| 131 |
#size-cells = <0>; |
| 132 |
compatible = "snps,dwmac-mdio"; |
| 133 |
|
| 134 |
/* KSZ8081RNA PHY */ |
| 135 |
ethphy0: ethernet-phy@0 { |
| 136 |
reg = <0>; |
| 137 |
interrupts-extended = <&gpiob 0 IRQ_TYPE_LEVEL_LOW>; |
| 138 |
reset-gpios = <&gpiob 1 GPIO_ACTIVE_LOW>; |
| 139 |
reset-assert-us = <10000>; |
| 140 |
reset-deassert-us = <300>; |
| 141 |
}; |
| 142 |
}; |
| 143 |
}; |
| 144 |
|
| 145 |
&gpioa { |
| 146 |
gpio-line-names = |
| 147 |
"", "", "", "", "", "", "", "", |
| 148 |
"", "", "", "", "", "HWID_PL_N", "HWID_CP", ""; |
| 149 |
}; |
| 150 |
|
| 151 |
&gpiob { |
| 152 |
gpio-line-names = |
| 153 |
"", "", "", "", "", "", "LED_LATCH", "", |
| 154 |
"", "RELAY1_EN", "", "", "", "", "", ""; |
| 155 |
}; |
| 156 |
|
| 157 |
&gpioc { |
| 158 |
gpio-line-names = |
| 159 |
"", "", "", "", "", "", "", "", |
| 160 |
"", "", "", "", "", "HWID_Q7", "", ""; |
| 161 |
}; |
| 162 |
|
| 163 |
&gpioe { |
| 164 |
gpio-line-names = |
| 165 |
"", "", "", "", "RELAY2_EN", "", "", "", |
| 166 |
"", "", "", "", "", "", "", ""; |
| 167 |
}; |
| 168 |
|
| 169 |
&gpiog { |
| 170 |
gpio-line-names = |
| 171 |
"", "", "", "", "", "", "", "SW1", |
| 172 |
"", "", "", "", "", "", "", ""; |
| 173 |
}; |
| 174 |
|
| 175 |
&gpioz { |
| 176 |
clocks = <&scmi_clk CK_SCMI_GPIOZ>; |
| 177 |
}; |
| 178 |
|
| 179 |
&hash1 { |
| 180 |
clocks = <&scmi_clk CK_SCMI_HASH1>; |
| 181 |
resets = <&scmi_reset RST_SCMI_HASH1>; |
| 182 |
}; |
| 183 |
|
| 184 |
&i2c1 { |
| 185 |
pinctrl-names = "default", "sleep"; |
| 186 |
pinctrl-0 = <&i2c1_pins_c>; |
| 187 |
pinctrl-1 = <&i2c1_sleep_pins_c>; |
| 188 |
i2c-scl-rising-time-ns = <185>; |
| 189 |
i2c-scl-falling-time-ns = <20>; |
| 190 |
status = "okay"; |
| 191 |
/delete-property/dmas; |
| 192 |
/delete-property/dma-names; |
| 193 |
}; |
| 194 |
|
| 195 |
&i2c4 { |
| 196 |
clocks = <&scmi_clk CK_SCMI_I2C4>; |
| 197 |
resets = <&scmi_reset RST_SCMI_I2C4>; |
| 198 |
}; |
| 199 |
|
| 200 |
&i2c6 { |
| 201 |
pinctrl-names = "default", "sleep"; |
| 202 |
pinctrl-0 = <&i2c6_pins_b>; |
| 203 |
pinctrl-1 = <&i2c6_sleep_pins_b>; |
| 204 |
i2c-scl-rising-time-ns = <185>; |
| 205 |
i2c-scl-falling-time-ns = <20>; |
| 206 |
clocks = <&scmi_clk CK_SCMI_I2C6>; |
| 207 |
resets = <&scmi_reset RST_SCMI_I2C6>; |
| 208 |
status = "okay"; |
| 209 |
/delete-property/dmas; |
| 210 |
/delete-property/dma-names; |
| 211 |
|
| 212 |
pressure-sensor@47 { |
| 213 |
compatible = "bosch,bmp580"; |
| 214 |
reg = <0x47>; |
| 215 |
vdda-supply = <&v5v_sw>; |
| 216 |
vddd-supply = <&v5v_sw>; |
| 217 |
}; |
| 218 |
|
| 219 |
co2-sensor@62 { |
| 220 |
compatible = "sensirion,scd41"; |
| 221 |
reg = <0x62>; |
| 222 |
vdd-supply = <&v5v_sw>; |
| 223 |
}; |
| 224 |
|
| 225 |
pm-sensor@69 { |
| 226 |
compatible = "sensirion,sps30"; |
| 227 |
reg = <0x69>; |
| 228 |
}; |
| 229 |
}; |
| 230 |
|
| 231 |
&i2s1 { |
| 232 |
pinctrl-names = "default", "sleep"; |
| 233 |
pinctrl-0 = <&i2s1_pins_a>; |
| 234 |
pinctrl-1 = <&i2s1_sleep_pins_a>; |
| 235 |
clocks = <&rcc SPI1>, <&rcc SPI1_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>; |
| 236 |
clock-names = "pclk", "i2sclk", "x8k", "x11k"; |
| 237 |
#clock-cells = <0>; /* Set I2S2 as master clock provider */ |
| 238 |
status = "okay"; |
| 239 |
|
| 240 |
i2s1_port: port { |
| 241 |
i2s1_endpoint: endpoint { |
| 242 |
dai-format = "i2s"; |
| 243 |
mclk-fs = <256>; |
| 244 |
remote-endpoint = <&codec_endpoint>; |
| 245 |
}; |
| 246 |
}; |
| 247 |
}; |
| 248 |
|
| 249 |
&iwdg2 { |
| 250 |
clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>; |
| 251 |
status = "okay"; |
| 252 |
}; |
| 253 |
|
| 254 |
&m4_rproc { |
| 255 |
/delete-property/ st,syscfg-holdboot; |
| 256 |
resets = <&scmi_reset RST_SCMI_MCU>, |
| 257 |
<&scmi_reset RST_SCMI_MCU_HOLD_BOOT>; |
| 258 |
reset-names = "mcu_rst", "hold_boot"; |
| 259 |
}; |
| 260 |
|
| 261 |
&mdma1 { |
| 262 |
resets = <&scmi_reset RST_SCMI_MDMA>; |
| 263 |
}; |
| 264 |
|
| 265 |
&rcc { |
| 266 |
compatible = "st,stm32mp1-rcc-secure", "syscon"; |
| 267 |
clock-names = "hse", "hsi", "csi", "lse", "lsi"; |
| 268 |
clocks = <&scmi_clk CK_SCMI_HSE>, |
| 269 |
<&scmi_clk CK_SCMI_HSI>, |
| 270 |
<&scmi_clk CK_SCMI_CSI>, |
| 271 |
<&scmi_clk CK_SCMI_LSE>, |
| 272 |
<&scmi_clk CK_SCMI_LSI>; |
| 273 |
}; |
| 274 |
|
| 275 |
&rng1 { |
| 276 |
clocks = <&scmi_clk CK_SCMI_RNG1>; |
| 277 |
resets = <&scmi_reset RST_SCMI_RNG1>; |
| 278 |
status = "okay"; |
| 279 |
}; |
| 280 |
|
| 281 |
&rtc { |
| 282 |
clocks = <&scmi_clk CK_SCMI_RTCAPB>, <&scmi_clk CK_SCMI_RTC>; |
| 283 |
}; |
| 284 |
|
| 285 |
/* SD card without Card-detect */ |
| 286 |
&sdmmc1 { |
| 287 |
pinctrl-names = "default", "opendrain", "sleep"; |
| 288 |
pinctrl-0 = <&sdmmc1_b4_pins_a>; |
| 289 |
pinctrl-1 = <&sdmmc1_b4_od_pins_a>; |
| 290 |
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; |
| 291 |
broken-cd; |
| 292 |
no-sdio; |
| 293 |
no-1-8-v; |
| 294 |
st,neg-edge; |
| 295 |
bus-width = <4>; |
| 296 |
vmmc-supply = <&v3v3>; |
| 297 |
status = "okay"; |
| 298 |
}; |
| 299 |
|
| 300 |
/* EMMC */ |
| 301 |
&sdmmc2 { |
| 302 |
pinctrl-names = "default", "opendrain", "sleep"; |
| 303 |
pinctrl-0 = <&sdmmc2_b4_pins_c &sdmmc2_d47_pins_b>; |
| 304 |
pinctrl-1 = <&sdmmc2_b4_od_pins_c &sdmmc2_d47_pins_b>; |
| 305 |
pinctrl-2 = <&sdmmc2_b4_sleep_pins_c &sdmmc2_d47_sleep_pins_b>; |
| 306 |
non-removable; |
| 307 |
no-sd; |
| 308 |
no-sdio; |
| 309 |
no-1-8-v; |
| 310 |
st,neg-edge; |
| 311 |
bus-width = <8>; |
| 312 |
vmmc-supply = <&v3v3>; |
| 313 |
status = "okay"; |
| 314 |
}; |
| 315 |
|
| 316 |
/* Wifi */ |
| 317 |
&sdmmc3 { |
| 318 |
pinctrl-names = "default", "opendrain", "sleep"; |
| 319 |
pinctrl-0 = <&sdmmc3_b4_pins_c>; |
| 320 |
pinctrl-1 = <&sdmmc3_b4_od_pins_c>; |
| 321 |
pinctrl-2 = <&sdmmc3_b4_sleep_pins_c>; |
| 322 |
non-removable; |
| 323 |
st,neg-edge; |
| 324 |
bus-width = <4>; |
| 325 |
vmmc-supply = <&v3v3>; |
| 326 |
mmc-pwrseq = <&wifi_pwrseq>; |
| 327 |
#address-cells = <1>; |
| 328 |
#size-cells = <0>; |
| 329 |
status = "okay"; |
| 330 |
|
| 331 |
wifi@1 { |
| 332 |
reg = <1>; |
| 333 |
compatible = "brcm,bcm4329-fmac"; |
| 334 |
}; |
| 335 |
}; |
| 336 |
|
| 337 |
&timers5 { |
| 338 |
status = "okay"; |
| 339 |
/delete-property/dmas; |
| 340 |
/delete-property/dma-names; |
| 341 |
|
| 342 |
pwm { |
| 343 |
pinctrl-0 = <&pwm1_pins_d>; |
| 344 |
pinctrl-1 = <&pwm1_sleep_pins_d>; |
| 345 |
pinctrl-names = "default", "sleep"; |
| 346 |
status = "okay"; |
| 347 |
}; |
| 348 |
}; |
| 349 |
|
| 350 |
&uart4 { |
| 351 |
pinctrl-names = "default", "sleep", "idle"; |
| 352 |
pinctrl-0 = <&uart4_pins_e>; |
| 353 |
pinctrl-1 = <&uart4_idle_pins_e>; |
| 354 |
pinctrl-2 = <&uart4_sleep_pins_e>; |
| 355 |
/delete-property/dmas; |
| 356 |
/delete-property/dma-names; |
| 357 |
status = "okay"; |
| 358 |
}; |
| 359 |
|
| 360 |
&uart7 { |
| 361 |
pinctrl-names = "default"; |
| 362 |
pinctrl-0 = <&uart7_pins_d>; |
| 363 |
uart-has-rtscts; |
| 364 |
status = "okay"; |
| 365 |
|
| 366 |
bluetooth { |
| 367 |
compatible = "brcm,bcm43438-bt"; |
| 368 |
shutdown-gpios = <&gpioe 11 GPIO_ACTIVE_HIGH>; /* BT_REG_ON */ |
| 369 |
max-speed = <4000000>; |
| 370 |
vbat-supply = <&v3v3>; |
| 371 |
vddio-supply = <&v3v3>; |
| 372 |
interrupt-parent = <&gpiog>; |
| 373 |
interrupts = <12 IRQ_TYPE_EDGE_RISING>; /* BT_HOST_WAKE */ |
| 374 |
interrupt-names = "host-wakeup"; |
| 375 |
}; |
| 376 |
}; |