| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Devicetree for the Samsung Galaxy Amp SGH-I407 also known as Kyle. |
| 4 |
* |
| 5 |
* The code also refers to "Kyle AT&T" reflecting that this mobile phone |
| 6 |
* was customized for the AT&T subsidiary Aio Wireless (All In One) and |
| 7 |
* offered by the company in 2013. |
| 8 |
*/ |
| 9 |
|
| 10 |
/dts-v1/; |
| 11 |
#include "ste-db8500.dtsi" |
| 12 |
#include "ste-ab8505.dtsi" |
| 13 |
#include "ste-dbx5x0-pinctrl.dtsi" |
| 14 |
#include <dt-bindings/gpio/gpio.h> |
| 15 |
#include <dt-bindings/leds/common.h> |
| 16 |
#include <dt-bindings/input/input.h> |
| 17 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 18 |
|
| 19 |
/ { |
| 20 |
model = "Samsung Galaxy Amp (SGH-I407)"; |
| 21 |
compatible = "samsung,kyle", "st-ericsson,u8500"; |
| 22 |
|
| 23 |
chosen { |
| 24 |
stdout-path = &serial2; |
| 25 |
}; |
| 26 |
|
| 27 |
battery: battery { |
| 28 |
compatible = "samsung,eb425161la"; |
| 29 |
}; |
| 30 |
|
| 31 |
thermal-zones { |
| 32 |
battery-thermal { |
| 33 |
/* This zone will be polled by the battery temperature code */ |
| 34 |
polling-delay = <0>; |
| 35 |
polling-delay-passive = <0>; |
| 36 |
thermal-sensors = <&bat_therm>; |
| 37 |
|
| 38 |
trips { |
| 39 |
battery-crit-hi { |
| 40 |
temperature = <70000>; |
| 41 |
hysteresis = <2000>; |
| 42 |
type = "critical"; |
| 43 |
}; |
| 44 |
}; |
| 45 |
}; |
| 46 |
}; |
| 47 |
|
| 48 |
bat_therm: thermistor { |
| 49 |
compatible = "samsung,1404-001221"; |
| 50 |
io-channels = <&gpadc 0x02>; /* BatTemp */ |
| 51 |
pullup-uv = <1800000>; |
| 52 |
pullup-ohm = <230000>; |
| 53 |
pulldown-ohm = <0>; |
| 54 |
#thermal-sensor-cells = <0>; |
| 55 |
}; |
| 56 |
|
| 57 |
/* TI TXS0206 level translator for 2.9 V */ |
| 58 |
sd_level_translator: regulator-gpio { |
| 59 |
compatible = "regulator-fixed"; |
| 60 |
|
| 61 |
/* GPIO87 EN */ |
| 62 |
gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>; |
| 63 |
enable-active-high; |
| 64 |
|
| 65 |
regulator-name = "sd-level-translator"; |
| 66 |
regulator-min-microvolt = <2900000>; |
| 67 |
regulator-max-microvolt = <2900000>; |
| 68 |
regulator-type = "voltage"; |
| 69 |
|
| 70 |
startup-delay-us = <200>; |
| 71 |
|
| 72 |
pinctrl-names = "default"; |
| 73 |
pinctrl-0 = <&sd_level_translator_default>; |
| 74 |
}; |
| 75 |
|
| 76 |
/* External LDO MIC5366-3.3YMT for eMMC */ |
| 77 |
ldo_3v3_reg: regulator-gpio-ldo-3v3 { |
| 78 |
compatible = "regulator-fixed"; |
| 79 |
regulator-name = "en-3v3-fixed-supply"; |
| 80 |
regulator-min-microvolt = <3300000>; |
| 81 |
regulator-max-microvolt = <3300000>; |
| 82 |
gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>; |
| 83 |
startup-delay-us = <5000>; |
| 84 |
enable-active-high; |
| 85 |
pinctrl-names = "default"; |
| 86 |
pinctrl-0 = <&emmc_ldo_en_default_mode>; |
| 87 |
}; |
| 88 |
|
| 89 |
/* |
| 90 |
* External Ricoh RP152L010B-TR LCD LDO regulator for the display. |
| 91 |
* LCD_PWR_EN controls both a 3.0V and 1.8V output. |
| 92 |
*/ |
| 93 |
lcd_3v0_reg: regulator-gpio-lcd-3v0 { |
| 94 |
compatible = "regulator-fixed"; |
| 95 |
/* Supplied in turn by VBAT */ |
| 96 |
regulator-name = "VREG_LCD_3V0"; |
| 97 |
regulator-min-microvolt = <3000000>; |
| 98 |
regulator-max-microvolt = <3000000>; |
| 99 |
/* GPIO219 controls this regulator */ |
| 100 |
gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; |
| 101 |
enable-active-high; |
| 102 |
pinctrl-names = "default"; |
| 103 |
pinctrl-0 = <&lcd_pwr_en_default_mode>; |
| 104 |
}; |
| 105 |
lcd_1v8_reg: regulator-gpio-lcd-1v8 { |
| 106 |
compatible = "regulator-fixed"; |
| 107 |
/* Supplied in turn by VBAT */ |
| 108 |
regulator-name = "VREG_LCD_1V8"; |
| 109 |
regulator-min-microvolt = <1800000>; |
| 110 |
regulator-max-microvolt = <1800000>; |
| 111 |
/* GPIO219 controls this regulator too */ |
| 112 |
gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; |
| 113 |
enable-active-high; |
| 114 |
pinctrl-names = "default"; |
| 115 |
pinctrl-0 = <&lcd_pwr_en_default_mode>; |
| 116 |
}; |
| 117 |
|
| 118 |
wlan_en: regulator-gpio-wlan-en { |
| 119 |
compatible = "regulator-fixed"; |
| 120 |
regulator-name = "wl-reg-on"; |
| 121 |
regulator-min-microvolt = <3000000>; |
| 122 |
regulator-max-microvolt = <3000000>; |
| 123 |
startup-delay-us = <200000>; |
| 124 |
/* GPIO215 WLAN_EN */ |
| 125 |
gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>; |
| 126 |
enable-active-high; |
| 127 |
pinctrl-names = "default"; |
| 128 |
pinctrl-0 = <&wlan_en_default_mode>; |
| 129 |
}; |
| 130 |
|
| 131 |
vibrator { |
| 132 |
compatible = "gpio-vibrator"; |
| 133 |
enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; |
| 134 |
pinctrl-names = "default"; |
| 135 |
pinctrl-0 = <&vibrator_default>; |
| 136 |
}; |
| 137 |
|
| 138 |
gpio-keys { |
| 139 |
compatible = "gpio-keys"; |
| 140 |
pinctrl-names = "default"; |
| 141 |
pinctrl-0 = <&gpio_keys_default_mode>; |
| 142 |
|
| 143 |
button-home { |
| 144 |
linux,code = <KEY_HOME>; |
| 145 |
label = "HOME"; |
| 146 |
/* GPIO91 */ |
| 147 |
gpios = <&gpio2 27 GPIO_ACTIVE_LOW>; |
| 148 |
}; |
| 149 |
button-volup { |
| 150 |
linux,code = <KEY_VOLUMEUP>; |
| 151 |
label = "VOL+"; |
| 152 |
/* GPIO67 */ |
| 153 |
gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; |
| 154 |
}; |
| 155 |
button-voldown { |
| 156 |
linux,code = <KEY_VOLUMEDOWN>; |
| 157 |
label = "VOL-"; |
| 158 |
/* GPIO92 */ |
| 159 |
gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; |
| 160 |
}; |
| 161 |
}; |
| 162 |
|
| 163 |
ktd253: backlight { |
| 164 |
compatible = "kinetic,ktd253"; |
| 165 |
/* GPIO 69 */ |
| 166 |
enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; |
| 167 |
/* Default to 13/32 brightness */ |
| 168 |
default-brightness = <13>; |
| 169 |
pinctrl-names = "default"; |
| 170 |
pinctrl-0 = <&gpio_backlight_default_mode>; |
| 171 |
}; |
| 172 |
|
| 173 |
/* Richtek RT8515GQW Flash LED Driver IC */ |
| 174 |
flash { |
| 175 |
compatible = "richtek,rt8515"; |
| 176 |
/* GPIO 140 */ |
| 177 |
enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; |
| 178 |
/* GPIO 141 */ |
| 179 |
ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>; |
| 180 |
/* |
| 181 |
* RFS is 16 kOhm and RTS is 100 kOhm giving |
| 182 |
* the flash max current 343mA and torch max |
| 183 |
* current 55 mA. |
| 184 |
*/ |
| 185 |
richtek,rfs-ohms = <16000>; |
| 186 |
richtek,rts-ohms = <100000>; |
| 187 |
pinctrl-names = "default"; |
| 188 |
pinctrl-0 = <&gpio_flash_default_mode>; |
| 189 |
|
| 190 |
led { |
| 191 |
function = LED_FUNCTION_FLASH; |
| 192 |
color = <LED_COLOR_ID_WHITE>; |
| 193 |
flash-max-timeout-us = <250000>; |
| 194 |
flash-max-microamp = <343750>; |
| 195 |
led-max-microamp = <55000>; |
| 196 |
}; |
| 197 |
}; |
| 198 |
|
| 199 |
i2c-gpio-0 { |
| 200 |
compatible = "i2c-gpio"; |
| 201 |
sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 202 |
scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 203 |
pinctrl-names = "default"; |
| 204 |
pinctrl-0 = <&i2c_gpio_0_default>; |
| 205 |
#address-cells = <1>; |
| 206 |
#size-cells = <0>; |
| 207 |
/* TODO: this should be used by the NCP6914 Camera power management unit */ |
| 208 |
}; |
| 209 |
|
| 210 |
i2c-gpio-1 { |
| 211 |
compatible = "i2c-gpio"; |
| 212 |
sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 213 |
scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 214 |
pinctrl-names = "default"; |
| 215 |
pinctrl-0 = <&i2c_gpio_1_default>; |
| 216 |
#address-cells = <1>; |
| 217 |
#size-cells = <0>; |
| 218 |
magnetometer@c { |
| 219 |
compatible = "alps,hscdtd008a"; |
| 220 |
reg = <0x0c>; |
| 221 |
avdd-supply = <&ab8500_ldo_aux1_reg>; |
| 222 |
dvdd-supply = <&ab8500_ldo_aux6_reg>; |
| 223 |
}; |
| 224 |
}; |
| 225 |
|
| 226 |
soc { |
| 227 |
// External Micro SD slot |
| 228 |
mmc@80126000 { |
| 229 |
arm,primecell-periphid = <0x10480180>; |
| 230 |
max-frequency = <100000000>; |
| 231 |
bus-width = <4>; |
| 232 |
cap-sd-highspeed; |
| 233 |
cap-mmc-highspeed; |
| 234 |
st,sig-pin-fbclk; |
| 235 |
full-pwr-cycle; |
| 236 |
vmmc-supply = <&ab8500_ldo_aux3_reg>; |
| 237 |
vqmmc-supply = <&sd_level_translator>; |
| 238 |
pinctrl-names = "default", "sleep"; |
| 239 |
pinctrl-0 = <&mc0_a_1_default>; |
| 240 |
pinctrl-1 = <&mc0_a_1_sleep>; |
| 241 |
cd-gpios = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217 |
| 242 |
status = "okay"; |
| 243 |
}; |
| 244 |
|
| 245 |
// WLAN SDIO channel |
| 246 |
mmc@80118000 { |
| 247 |
arm,primecell-periphid = <0x10480180>; |
| 248 |
max-frequency = <50000000>; |
| 249 |
bus-width = <4>; |
| 250 |
non-removable; |
| 251 |
cap-sd-highspeed; |
| 252 |
vmmc-supply = <&wlan_en>; |
| 253 |
pinctrl-names = "default", "sleep"; |
| 254 |
pinctrl-0 = <&mc1_a_2_default>; |
| 255 |
pinctrl-1 = <&mc1_a_2_sleep>; |
| 256 |
status = "okay"; |
| 257 |
#address-cells = <1>; |
| 258 |
#size-cells = <0>; |
| 259 |
|
| 260 |
wifi@1 { |
| 261 |
compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac"; |
| 262 |
reg = <1>; |
| 263 |
/* GPIO216 WL_HOST_WAKE */ |
| 264 |
interrupt-parent = <&gpio6>; |
| 265 |
interrupts = <24 IRQ_TYPE_EDGE_FALLING>; |
| 266 |
interrupt-names = "host-wake"; |
| 267 |
pinctrl-names = "default"; |
| 268 |
pinctrl-0 = <&wlan_default_mode>; |
| 269 |
}; |
| 270 |
}; |
| 271 |
|
| 272 |
/* |
| 273 |
* eMMC seems to be mostly Samsung KLM4G1YE4C "4YMD1R" |
| 274 |
*/ |
| 275 |
mmc@80005000 { |
| 276 |
arm,primecell-periphid = <0x10480180>; |
| 277 |
max-frequency = <100000000>; |
| 278 |
bus-width = <8>; |
| 279 |
non-removable; |
| 280 |
cap-mmc-highspeed; |
| 281 |
mmc-ddr-1_8v; |
| 282 |
no-sdio; |
| 283 |
no-sd; |
| 284 |
/* From datasheet page 26 figure 9: 300 ms set-up time for 4GB */ |
| 285 |
post-power-on-delay-ms = <300>; |
| 286 |
vmmc-supply = <&ldo_3v3_reg>; |
| 287 |
pinctrl-names = "default", "sleep"; |
| 288 |
pinctrl-0 = <&mc2_a_1_default>; |
| 289 |
pinctrl-1 = <&mc2_a_1_sleep>; |
| 290 |
|
| 291 |
status = "okay"; |
| 292 |
}; |
| 293 |
|
| 294 |
/* GBF (Bluetooth) UART */ |
| 295 |
serial@80120000 { |
| 296 |
pinctrl-names = "default", "sleep"; |
| 297 |
pinctrl-0 = <&u0_a_1_default>; |
| 298 |
pinctrl-1 = <&u0_a_1_sleep>; |
| 299 |
status = "okay"; |
| 300 |
|
| 301 |
bluetooth { |
| 302 |
/* BCM4334B0 actually */ |
| 303 |
compatible = "brcm,bcm4330-bt"; |
| 304 |
shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>; |
| 305 |
device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>; |
| 306 |
host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>; |
| 307 |
pinctrl-names = "default"; |
| 308 |
pinctrl-0 = <&bluetooth_default_mode>; |
| 309 |
}; |
| 310 |
}; |
| 311 |
|
| 312 |
/* GPF UART */ |
| 313 |
serial@80121000 { |
| 314 |
status = "okay"; |
| 315 |
pinctrl-names = "default", "sleep"; |
| 316 |
pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>; |
| 317 |
pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>; |
| 318 |
|
| 319 |
gnss { |
| 320 |
/* The CSRG05TA03-ICJE-R is a SirfStarV 5t chip */ |
| 321 |
compatible = "csr,csrg05ta03-icje-r"; |
| 322 |
/* GPS_RSTN on GPIO21 */ |
| 323 |
reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; |
| 324 |
/* GPS_ON_OFF on GPIO86 */ |
| 325 |
sirf,onoff-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; |
| 326 |
/* GPS_1V8 (VSMPS2) */ |
| 327 |
vcc-supply = <&db8500_vsmps2_reg>; |
| 328 |
pinctrl-names = "default"; |
| 329 |
pinctrl-0 = <&g05ta03_kyle_default>; |
| 330 |
/* According to /etc/sirfgps.conf */ |
| 331 |
current-speed = <460800>; |
| 332 |
}; |
| 333 |
}; |
| 334 |
|
| 335 |
/* Debugging console UART connected to AB8505 USB */ |
| 336 |
serial@80007000 { |
| 337 |
status = "okay"; |
| 338 |
pinctrl-names = "default", "sleep"; |
| 339 |
pinctrl-0 = <&u2rxtx_c_1_default>; |
| 340 |
pinctrl-1 = <&u2rxtx_c_1_sleep>; |
| 341 |
}; |
| 342 |
|
| 343 |
prcmu@80157000 { |
| 344 |
ab8505 { |
| 345 |
phy { |
| 346 |
pinctrl-names = "default", "sleep"; |
| 347 |
pinctrl-0 = <&usb_a_1_default>; |
| 348 |
pinctrl-1 = <&usb_a_1_sleep>; |
| 349 |
}; |
| 350 |
|
| 351 |
ab8500_fg { |
| 352 |
line-impedance-micro-ohms = <36000>; |
| 353 |
}; |
| 354 |
|
| 355 |
regulator { |
| 356 |
ab8500_ldo_aux1 { |
| 357 |
/* Used for VDD for sensors */ |
| 358 |
regulator-name = "AUX1"; |
| 359 |
regulator-min-microvolt = <3000000>; |
| 360 |
regulator-max-microvolt = <3300000>; |
| 361 |
}; |
| 362 |
|
| 363 |
ab8500_ldo_aux2 { |
| 364 |
/* Supplies the MMS touchscreen only with 3.3V */ |
| 365 |
regulator-name = "AUX2"; |
| 366 |
regulator-min-microvolt = <3300000>; |
| 367 |
regulator-max-microvolt = <3300000>; |
| 368 |
}; |
| 369 |
|
| 370 |
ab8500_ldo_aux3 { |
| 371 |
/* Used for voltage for external MMC/SD card */ |
| 372 |
regulator-name = "AUX3"; |
| 373 |
regulator-min-microvolt = <1100000>; |
| 374 |
regulator-max-microvolt = <3300000>; |
| 375 |
}; |
| 376 |
|
| 377 |
ab8500_ldo_aux4 { |
| 378 |
regulator-name = "AUX4"; |
| 379 |
/* Hammer to 3.3V for the touchscreen */ |
| 380 |
regulator-min-microvolt = <3300000>; |
| 381 |
regulator-max-microvolt = <3300000>; |
| 382 |
}; |
| 383 |
|
| 384 |
ab8500_ldo_aux5 { |
| 385 |
regulator-name = "AUX5"; |
| 386 |
/* 1.8V for the touchscreen */ |
| 387 |
regulator-min-microvolt = <1800000>; |
| 388 |
regulator-max-microvolt = <1800000>; |
| 389 |
}; |
| 390 |
|
| 391 |
ab8500_ldo_aux6 { |
| 392 |
regulator-name = "AUX6"; |
| 393 |
/* Used by sensors for 1.8 V in R0.1+ */ |
| 394 |
regulator-min-microvolt = <1800000>; |
| 395 |
regulator-max-microvolt = <1800000>; |
| 396 |
}; |
| 397 |
|
| 398 |
ab8500_ldo_aux8 { |
| 399 |
/* Unused */ |
| 400 |
regulator-name = "AUX8"; |
| 401 |
}; |
| 402 |
}; |
| 403 |
}; |
| 404 |
}; |
| 405 |
|
| 406 |
/* I2C0 */ |
| 407 |
i2c@80004000 { |
| 408 |
status = "okay"; |
| 409 |
|
| 410 |
pinctrl-names = "default", "sleep"; |
| 411 |
pinctrl-0 = <&i2c0_a_1_default>; |
| 412 |
pinctrl-1 = <&i2c0_a_1_sleep>; |
| 413 |
|
| 414 |
proximity@44 { |
| 415 |
compatible = "sharp,gp2ap002s00f"; |
| 416 |
clock-frequency = <400000>; |
| 417 |
reg = <0x44>; |
| 418 |
|
| 419 |
interrupt-parent = <&gpio4>; |
| 420 |
interrupts = <18 IRQ_TYPE_EDGE_FALLING>; |
| 421 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 422 |
vio-supply = <&ab8500_ldo_aux6_reg>; |
| 423 |
pinctrl-names = "default"; |
| 424 |
pinctrl-0 = <&gp2ap002_kyle_default>; |
| 425 |
sharp,proximity-far-hysteresis = /bits/ 8 <0x2f>; |
| 426 |
sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>; |
| 427 |
}; |
| 428 |
}; |
| 429 |
|
| 430 |
/* I2C2 */ |
| 431 |
i2c@80128000 { |
| 432 |
status = "okay"; |
| 433 |
|
| 434 |
pinctrl-names = "default", "sleep"; |
| 435 |
pinctrl-0 = <&i2c2_b_2_default>; |
| 436 |
pinctrl-1 = <&i2c2_b_2_sleep>; |
| 437 |
|
| 438 |
accel@18 { |
| 439 |
compatible = "bosch,bma254"; |
| 440 |
clock-frequency = <400000>; |
| 441 |
reg = <0x18>; |
| 442 |
|
| 443 |
mount-matrix = "-1", "0", "0", |
| 444 |
"0", "-1", "0", |
| 445 |
"0", "0", "-1"; |
| 446 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 447 |
vddio-supply = <&ab8500_ldo_aux6_reg>; |
| 448 |
}; |
| 449 |
}; |
| 450 |
|
| 451 |
/* I2C3 */ |
| 452 |
i2c@80110000 { |
| 453 |
status = "okay"; |
| 454 |
|
| 455 |
pinctrl-names = "default", "sleep"; |
| 456 |
pinctrl-0 = <&i2c3_c_2_default>; |
| 457 |
pinctrl-1 = <&i2c3_c_2_sleep>; |
| 458 |
|
| 459 |
/* Melfas MMS134S touchscreen */ |
| 460 |
touchscreen@48 { |
| 461 |
compatible = "melfas,mms134s"; |
| 462 |
reg = <0x48>; |
| 463 |
/* GPIO218 for IRQ */ |
| 464 |
interrupt-parent = <&gpio6>; |
| 465 |
interrupts = <26 IRQ_TYPE_EDGE_FALLING>; |
| 466 |
/* AVDD is "analog supply", 2.57-3.47 V */ |
| 467 |
avdd-supply = <&ab8500_ldo_aux2_reg>; |
| 468 |
/* VDD is "digital supply" 1.71-3.47V */ |
| 469 |
vdd-supply = <&ab8500_ldo_aux5_reg>; |
| 470 |
|
| 471 |
touchscreen-size-x = <480>; |
| 472 |
touchscreen-size-y = <800>; |
| 473 |
|
| 474 |
pinctrl-names = "default"; |
| 475 |
pinctrl-0 = <&mms134s_kyle_default>; |
| 476 |
}; |
| 477 |
}; |
| 478 |
|
| 479 |
mcde@a0350000 { |
| 480 |
status = "okay"; |
| 481 |
pinctrl-names = "default"; |
| 482 |
pinctrl-0 = <&dsi_default_mode>; |
| 483 |
|
| 484 |
dsi@a0351000 { |
| 485 |
panel { |
| 486 |
/* |
| 487 |
* NT35510-based Hydis HVA40WV1 |
| 488 |
* Apparently some Kyle models can have a NT35512 fitted |
| 489 |
* here instead. In that case the boot loader needs to |
| 490 |
* modify this compatible. |
| 491 |
*/ |
| 492 |
compatible = "hydis,hva40wv1", "novatek,nt35510"; |
| 493 |
reg = <0>; |
| 494 |
/* v_lcd_3v0 2.3-4.8V */ |
| 495 |
vdd-supply = <&lcd_3v0_reg>; |
| 496 |
/* v_lcd_1v8 1.65-3.3V */ |
| 497 |
vddi-supply = <&lcd_1v8_reg>; |
| 498 |
/* GPIO 139 */ |
| 499 |
reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; |
| 500 |
pinctrl-names = "default"; |
| 501 |
pinctrl-0 = <&display_default_mode>; |
| 502 |
backlight = <&ktd253>; |
| 503 |
}; |
| 504 |
}; |
| 505 |
}; |
| 506 |
}; |
| 507 |
}; |
| 508 |
|
| 509 |
&pinctrl { |
| 510 |
/* |
| 511 |
* This extends the MC0_A_1 default config to include |
| 512 |
* the card detect GPIO217 line. |
| 513 |
*/ |
| 514 |
sdi0 { |
| 515 |
mc0_a_1_default { |
| 516 |
default_cfg1 { |
| 517 |
/* GPIO18, 19 & 20 unused so pull down */ |
| 518 |
ste,config = <&gpio_in_pd>; |
| 519 |
}; |
| 520 |
default_cfg4 { |
| 521 |
pins = "GPIO217_AH12"; /* card detect */ |
| 522 |
ste,config = <&gpio_in_pd>; |
| 523 |
}; |
| 524 |
}; |
| 525 |
}; |
| 526 |
|
| 527 |
mcde { |
| 528 |
dsi_default_mode: dsi_default { |
| 529 |
default_mux1 { |
| 530 |
/* Mux in VSI0 used for DSI TE */ |
| 531 |
function = "lcd"; |
| 532 |
groups = "lcdvsi0_a_1"; /* VSI0 for LCD */ |
| 533 |
}; |
| 534 |
default_cfg1 { |
| 535 |
pins = "GPIO68_E1"; /* VSI0 */ |
| 536 |
ste,config = <&in_nopull>; |
| 537 |
}; |
| 538 |
}; |
| 539 |
}; |
| 540 |
|
| 541 |
/* Two GPIO lines used by the display */ |
| 542 |
display { |
| 543 |
display_default_mode: display_default { |
| 544 |
kyle_cfg1 { |
| 545 |
/* |
| 546 |
* OLED DETECT or check_pba, this appears to be high |
| 547 |
* on "PBA" which I guess is "prototype board A". |
| 548 |
*/ |
| 549 |
pins = "GPIO93_B7"; |
| 550 |
ste,config = <&gpio_in_nopull>; |
| 551 |
}; |
| 552 |
kyle_cfg2 { |
| 553 |
pins = "GPIO139_C9"; |
| 554 |
/* |
| 555 |
* MIPI_DSI0_RESET_N resets the display, leave high |
| 556 |
* (de-asserted) so we only assert reset explicitly |
| 557 |
* from the display driver. |
| 558 |
*/ |
| 559 |
ste,config = <&gpio_out_hi>; |
| 560 |
}; |
| 561 |
}; |
| 562 |
}; |
| 563 |
|
| 564 |
/* GPIO that enables the LDO regulator for the LCD display */ |
| 565 |
lcd-ldo { |
| 566 |
lcd_pwr_en_default_mode: lcd_pwr_en_default { |
| 567 |
/* LCD_PWR_EN on GPIO219 */ |
| 568 |
kyle_cfg1 { |
| 569 |
pins = "GPIO219_AG10"; |
| 570 |
ste,config = <&gpio_out_hi>; |
| 571 |
}; |
| 572 |
}; |
| 573 |
}; |
| 574 |
|
| 575 |
backlight { |
| 576 |
gpio_backlight_default_mode: backlight_default { |
| 577 |
kyle_cfg1 { |
| 578 |
pins = "GPIO69_E2"; /* LCD_BL_CTRL */ |
| 579 |
ste,config = <&gpio_out_lo>; |
| 580 |
}; |
| 581 |
}; |
| 582 |
}; |
| 583 |
flash { |
| 584 |
gpio_flash_default_mode: flash_default { |
| 585 |
kyle_cfg1 { |
| 586 |
pins = "GPIO140_B11", "GPIO141_C12"; |
| 587 |
ste,config = <&gpio_out_lo>; |
| 588 |
}; |
| 589 |
}; |
| 590 |
}; |
| 591 |
/* GPIO that enables the 2.9V SD card level translator */ |
| 592 |
sd-level-translator { |
| 593 |
sd_level_translator_default: sd_level_translator_default { |
| 594 |
/* level shifter on GPIO87 */ |
| 595 |
kyle_cfg1 { |
| 596 |
pins = "GPIO87_B3"; |
| 597 |
ste,config = <&gpio_out_hi>; |
| 598 |
}; |
| 599 |
}; |
| 600 |
}; |
| 601 |
/* GPIO that enables the LDO regulator for the eMMC */ |
| 602 |
emmc-ldo { |
| 603 |
emmc_ldo_en_default_mode: emmc_ldo_default { |
| 604 |
/* LDO enable on GPIO223 */ |
| 605 |
kyle_cfg1 { |
| 606 |
pins = "GPIO223_AH9"; |
| 607 |
ste,config = <&gpio_out_hi>; |
| 608 |
}; |
| 609 |
}; |
| 610 |
}; |
| 611 |
/* GPIO keys */ |
| 612 |
gpio-keys { |
| 613 |
gpio_keys_default_mode: gpio_keys_default { |
| 614 |
kyle_cfg1 { |
| 615 |
pins = "GPIO67_G2", /* VOL UP */ |
| 616 |
"GPIO91_B6", /* HOME */ |
| 617 |
"GPIO92_D6"; /* VOL DOWN */ |
| 618 |
ste,config = <&gpio_in_pu>; |
| 619 |
}; |
| 620 |
}; |
| 621 |
}; |
| 622 |
/* Interrupt line for light/proximity sensor GP2AP002 */ |
| 623 |
gp2ap002 { |
| 624 |
gp2ap002_kyle_default: gp2ap002_kyle { |
| 625 |
kyle_cfg1 { |
| 626 |
pins = "GPIO146_D13"; |
| 627 |
ste,config = <&gpio_in_nopull>; |
| 628 |
}; |
| 629 |
}; |
| 630 |
}; |
| 631 |
/* GPIO-based I2C bus for NCP6914 */ |
| 632 |
i2c-gpio-0 { |
| 633 |
i2c_gpio_0_default: i2c_gpio_0 { |
| 634 |
kyle_cfg1 { |
| 635 |
pins = "GPIO143_D12", "GPIO144_B13"; |
| 636 |
ste,config = <&gpio_in_nopull>; |
| 637 |
}; |
| 638 |
}; |
| 639 |
}; |
| 640 |
/* GPIO-based I2C bus for ALPS HSCD compass */ |
| 641 |
i2c-gpio-1 { |
| 642 |
i2c_gpio_1_default: i2c_gpio_1 { |
| 643 |
kyle_cfg1 { |
| 644 |
pins = "GPIO151_B17", "GPIO152_D16"; |
| 645 |
ste,config = <&gpio_in_nopull>; |
| 646 |
}; |
| 647 |
}; |
| 648 |
}; |
| 649 |
wlan { |
| 650 |
wlan_default_mode: wlan_default { |
| 651 |
kyle_cfg1 { |
| 652 |
pins = "GPIO216_AG12"; |
| 653 |
ste,config = <&gpio_in_pd>; |
| 654 |
}; |
| 655 |
}; |
| 656 |
wlan_en_default_mode: wlan_en_default { |
| 657 |
kyle_cfg2 { |
| 658 |
pins = "GPIO215_AH13"; |
| 659 |
ste,config = <&gpio_out_lo>; |
| 660 |
}; |
| 661 |
}; |
| 662 |
}; |
| 663 |
bluetooth { |
| 664 |
bluetooth_default_mode: bluetooth_default { |
| 665 |
kyle_cfg1 { |
| 666 |
pins = "GPIO199_AH23", "GPIO222_AJ9"; |
| 667 |
ste,config = <&gpio_out_lo>; |
| 668 |
}; |
| 669 |
kyle_cfg2 { |
| 670 |
pins = "GPIO97_D9"; |
| 671 |
ste,config = <&gpio_in_nopull>; |
| 672 |
}; |
| 673 |
}; |
| 674 |
}; |
| 675 |
vibrator { |
| 676 |
vibrator_default: vibrator_default { |
| 677 |
kyle_cfg1 { |
| 678 |
pins = "GPIO195_AG28"; /* MOT_EN */ |
| 679 |
ste,config = <&gpio_out_lo>; |
| 680 |
}; |
| 681 |
}; |
| 682 |
}; |
| 683 |
/* Interrupt line for the Melfas MMS134S touchscreen */ |
| 684 |
touchscreen { |
| 685 |
mms134s_kyle_default: mms134s_kyle { |
| 686 |
kyle_cfg1 { |
| 687 |
pins = "GPIO218_AH11"; |
| 688 |
ste,config = <&gpio_in_nopull>; |
| 689 |
}; |
| 690 |
}; |
| 691 |
}; |
| 692 |
g05ta03 { |
| 693 |
g05ta03_kyle_default: g05ta03 { |
| 694 |
/* Reset line, start out de-asserted */ |
| 695 |
kyle_cfg1 { |
| 696 |
pins = "GPIO21_AB3"; |
| 697 |
ste,config = <&gpio_out_hi>; |
| 698 |
}; |
| 699 |
/* GPS_ON_OFF, start out deasserted (off) */ |
| 700 |
kyle_cfg2 { |
| 701 |
pins = "GPIO86_C6"; |
| 702 |
ste,config = <&gpio_out_lo>; |
| 703 |
}; |
| 704 |
}; |
| 705 |
}; |
| 706 |
}; |
| 707 |
|
| 708 |
&ab8505_gpio { |
| 709 |
/* Hog a few default settings */ |
| 710 |
pinctrl-names = "default"; |
| 711 |
pinctrl-0 = <&gpio_default>; |
| 712 |
|
| 713 |
gpio { |
| 714 |
gpio_default: gpio_default { |
| 715 |
kyle_mux { |
| 716 |
/* Change unused pins to GPIO mode */ |
| 717 |
function = "gpio"; |
| 718 |
groups = "gpio3_a_1", /* default: SysClkReq4 */ |
| 719 |
"gpio14_a_1"; /* default: PWMOut1 */ |
| 720 |
}; |
| 721 |
kyle_cfg1 { |
| 722 |
pins = "GPIO11_B17", "GPIO13_D17", "GPIO50_L4"; |
| 723 |
bias-disable; |
| 724 |
}; |
| 725 |
}; |
| 726 |
}; |
| 727 |
}; |