| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* Copyright 2011 ST-Ericsson AB |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
#include "ste-db9500.dtsi" |
| 8 |
#include "ste-href-ab8500.dtsi" |
| 9 |
#include "ste-href-family-pinctrl.dtsi" |
| 10 |
|
| 11 |
/ { |
| 12 |
model = "Calao Systems Snowball platform with device tree"; |
| 13 |
compatible = "calaosystems,snowball-a9500", "st-ericsson,u9500"; |
| 14 |
|
| 15 |
memory { |
| 16 |
device_type = "memory"; |
| 17 |
reg = <0x00000000 0x20000000>; |
| 18 |
}; |
| 19 |
|
| 20 |
battery: battery { |
| 21 |
compatible = "simple-battery"; |
| 22 |
battery-type = "lithium-ion-polymer"; |
| 23 |
}; |
| 24 |
|
| 25 |
thermal-zones { |
| 26 |
battery-thermal { |
| 27 |
/* This zone will be polled by the battery temperature code */ |
| 28 |
polling-delay = <0>; |
| 29 |
polling-delay-passive = <0>; |
| 30 |
thermal-sensors = <&bat_therm>; |
| 31 |
|
| 32 |
trips { |
| 33 |
battery-crit-hi { |
| 34 |
temperature = <70000>; |
| 35 |
hysteresis = <2000>; |
| 36 |
type = "critical"; |
| 37 |
}; |
| 38 |
}; |
| 39 |
}; |
| 40 |
}; |
| 41 |
|
| 42 |
bat_therm: thermistor { |
| 43 |
compatible = "murata,ncp18wb473"; |
| 44 |
io-channels = <&gpadc 0x02>; /* BatTemp */ |
| 45 |
pullup-uv = <1800000>; |
| 46 |
pullup-ohm = <230000>; |
| 47 |
pulldown-ohm = <0>; |
| 48 |
#thermal-sensor-cells = <0>; |
| 49 |
}; |
| 50 |
|
| 51 |
en_3v3_reg: en_3v3 { |
| 52 |
compatible = "regulator-fixed"; |
| 53 |
regulator-name = "en-3v3-fixed-supply"; |
| 54 |
regulator-min-microvolt = <3300000>; |
| 55 |
regulator-max-microvolt = <3300000>; |
| 56 |
/* AB8500 GPIOs start from 1 - offset 25 is GPIO26. */ |
| 57 |
gpio = <&ab8500_gpio 25 0x4>; |
| 58 |
startup-delay-us = <5000>; |
| 59 |
enable-active-high; |
| 60 |
}; |
| 61 |
|
| 62 |
gpio_keys { |
| 63 |
compatible = "gpio-keys"; |
| 64 |
#address-cells = <1>; |
| 65 |
#size-cells = <0>; |
| 66 |
|
| 67 |
button@1 { |
| 68 |
debounce-interval = <50>; |
| 69 |
wakeup-source; |
| 70 |
linux,code = <2>; |
| 71 |
label = "userpb"; |
| 72 |
gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>; |
| 73 |
}; |
| 74 |
button@2 { |
| 75 |
debounce-interval = <50>; |
| 76 |
wakeup-source; |
| 77 |
linux,code = <3>; |
| 78 |
label = "extkb1"; |
| 79 |
gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>; |
| 80 |
}; |
| 81 |
button@3 { |
| 82 |
debounce-interval = <50>; |
| 83 |
wakeup-source; |
| 84 |
linux,code = <4>; |
| 85 |
label = "extkb2"; |
| 86 |
gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>; |
| 87 |
}; |
| 88 |
button@4 { |
| 89 |
debounce-interval = <50>; |
| 90 |
wakeup-source; |
| 91 |
linux,code = <5>; |
| 92 |
label = "extkb3"; |
| 93 |
gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; |
| 94 |
}; |
| 95 |
button@5 { |
| 96 |
debounce-interval = <50>; |
| 97 |
wakeup-source; |
| 98 |
linux,code = <6>; |
| 99 |
label = "extkb4"; |
| 100 |
gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>; |
| 101 |
}; |
| 102 |
}; |
| 103 |
|
| 104 |
leds { |
| 105 |
compatible = "gpio-leds"; |
| 106 |
pinctrl-names = "default"; |
| 107 |
pinctrl-0 = <&gpioled_snowball_mode>; |
| 108 |
used-led { |
| 109 |
label = "user_led"; |
| 110 |
gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>; |
| 111 |
default-state = "on"; |
| 112 |
linux,default-trigger = "heartbeat"; |
| 113 |
}; |
| 114 |
}; |
| 115 |
|
| 116 |
soc { |
| 117 |
/* Name the GPIO muxed rails on the Snowball board */ |
| 118 |
gpio@8012e000 { |
| 119 |
/* GPIOs 0 - 31 */ |
| 120 |
gpio-line-names = "", "", "", "", "", "", "", "", |
| 121 |
"", "", "", "", "", "", "", "", |
| 122 |
"", "", "", "", "", "", "", "", |
| 123 |
"", "", "", "", "", "", "", |
| 124 |
"AP_GPIO31"; |
| 125 |
}; |
| 126 |
|
| 127 |
gpio@8012e080 { |
| 128 |
/* GPIOs 32 - 63 */ |
| 129 |
gpio-line-names = "USR PB", "", "", "", "", "", "", "", |
| 130 |
"", "", "", "", "", "", "", "", |
| 131 |
"", "", "", "", "", "", "", "", |
| 132 |
"", "", "", "", "", "", "", ""; |
| 133 |
}; |
| 134 |
|
| 135 |
gpio@8000e000 { |
| 136 |
/* GPIOs 64 - 95 */ |
| 137 |
gpio-line-names = "", "", "", "", "AP_GPIO68", "", "", "", |
| 138 |
"", "", "", "", "", "", "", "", |
| 139 |
"", "", "", "", "", "", "", "", |
| 140 |
"", "", "", "", "", "", "", ""; |
| 141 |
}; |
| 142 |
|
| 143 |
gpio@8000e100 { |
| 144 |
/* GPIOs 128 - 159 */ |
| 145 |
gpio-line-names = "", "", "", "", "", "", "", "", |
| 146 |
"", "", "", "", "IRQ_LAN", "RSTn_LAN", |
| 147 |
"USR_LED", "", "", "", "", "", "", |
| 148 |
"", "", "AP_GPIO151", "AP_GPIO152", |
| 149 |
"", "", "", "", "", "", ""; |
| 150 |
}; |
| 151 |
|
| 152 |
gpio@8000e180 { |
| 153 |
/* GPIOs 160 - 191 */ |
| 154 |
gpio-line-names = "", "AP_GPIO161", "AP_GPIO162", |
| 155 |
"ACCELEROMETER_INT1_RDY", |
| 156 |
"ACCELEROMETER_INT2", "MAG_DRDY", |
| 157 |
"GYRO_DRDY", "RSTn_MLC", "RSTn_SLC", |
| 158 |
"GYRO_INT", "UART_WAKE", "GBF_RESET", |
| 159 |
"", "", "", "", |
| 160 |
"", "", "", "", "", "", "", "", |
| 161 |
"", "", "", "", "", "", "", ""; |
| 162 |
}; |
| 163 |
|
| 164 |
gpio@8011e000 { |
| 165 |
/* GPIOs 192 - 223 */ |
| 166 |
gpio-line-names = "HDTV_INTn", "", "", "", "HDTV_RST", |
| 167 |
"", "", "", "", "", "", "", "", "", |
| 168 |
"", "", "", "", "", "", "", "", "", |
| 169 |
"WLAN_RESETN", "WLAN_IRQ", "MMC_EN", |
| 170 |
"MMC_CD", "", "", "", "", ""; |
| 171 |
}; |
| 172 |
|
| 173 |
gpio@8011e080 { |
| 174 |
/* GPIOs 224 - 255 */ |
| 175 |
gpio-line-names = "", "", "", "", "SD_SEL", "", "", "", |
| 176 |
"", "", "", "", "", "", "", "", |
| 177 |
"", "", "", "", "", "", "", "", |
| 178 |
"", "", "", "", "", "", "", ""; |
| 179 |
}; |
| 180 |
|
| 181 |
msp0: msp@80123000 { |
| 182 |
pinctrl-names = "default"; |
| 183 |
pinctrl-0 = <&msp0txrxtfstck_a_1_default>; |
| 184 |
status = "okay"; |
| 185 |
}; |
| 186 |
|
| 187 |
msp1: msp@80124000 { |
| 188 |
pinctrl-names = "default"; |
| 189 |
pinctrl-0 = <&msp1txrx_a_1_default>; |
| 190 |
status = "okay"; |
| 191 |
}; |
| 192 |
|
| 193 |
msp2: msp@80117000 { |
| 194 |
pinctrl-names = "default"; |
| 195 |
pinctrl-0 = <&msp2_a_1_default>; |
| 196 |
}; |
| 197 |
|
| 198 |
msp3: msp@80125000 { |
| 199 |
status = "okay"; |
| 200 |
}; |
| 201 |
|
| 202 |
external-bus@50000000 { |
| 203 |
status = "okay"; |
| 204 |
|
| 205 |
ethernet@0 { |
| 206 |
compatible = "smsc,lan9115"; |
| 207 |
reg = <0 0x10000>; |
| 208 |
interrupts = <12 IRQ_TYPE_EDGE_RISING>; |
| 209 |
interrupt-parent = <&gpio4>; |
| 210 |
vdd33a-supply = <&en_3v3_reg>; |
| 211 |
vddvario-supply = <&db8500_vape_reg>; |
| 212 |
pinctrl-names = "default"; |
| 213 |
pinctrl-0 = <ð_snowball_mode>; |
| 214 |
|
| 215 |
reg-shift = <1>; |
| 216 |
reg-io-width = <2>; |
| 217 |
smsc,force-internal-phy; |
| 218 |
smsc,irq-active-high; |
| 219 |
smsc,irq-push-pull; |
| 220 |
|
| 221 |
clocks = <&prcc_pclk 3 0>; |
| 222 |
}; |
| 223 |
}; |
| 224 |
|
| 225 |
/* ST6G3244ME level translator for 1.8/2.9 V */ |
| 226 |
vmmci: regulator-gpio { |
| 227 |
compatible = "regulator-gpio"; |
| 228 |
|
| 229 |
/* GPIO228 SD_SEL */ |
| 230 |
gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>; |
| 231 |
/* GPIO217 MMC_EN */ |
| 232 |
enable-gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>; |
| 233 |
enable-active-high; |
| 234 |
|
| 235 |
regulator-min-microvolt = <1800000>; |
| 236 |
regulator-max-microvolt = <2900000>; |
| 237 |
regulator-name = "mmci-reg"; |
| 238 |
regulator-type = "voltage"; |
| 239 |
|
| 240 |
startup-delay-us = <100>; |
| 241 |
|
| 242 |
states = <1800000 0x1 |
| 243 |
2900000 0x0>; |
| 244 |
}; |
| 245 |
|
| 246 |
// External Micro SD slot |
| 247 |
mmc@80126000 { |
| 248 |
arm,primecell-periphid = <0x10480180>; |
| 249 |
max-frequency = <100000000>; |
| 250 |
bus-width = <4>; |
| 251 |
cap-sd-highspeed; |
| 252 |
cap-mmc-highspeed; |
| 253 |
sd-uhs-sdr12; |
| 254 |
sd-uhs-sdr25; |
| 255 |
/* All direction control is used */ |
| 256 |
st,sig-dir-cmd; |
| 257 |
st,sig-dir-dat0; |
| 258 |
st,sig-dir-dat2; |
| 259 |
st,sig-dir-dat31; |
| 260 |
st,sig-pin-fbclk; |
| 261 |
full-pwr-cycle; |
| 262 |
vmmc-supply = <&ab8500_ldo_aux3_reg>; |
| 263 |
vqmmc-supply = <&vmmci>; |
| 264 |
pinctrl-names = "default", "sleep"; |
| 265 |
pinctrl-0 = <&mc0_a_1_default &sdi0_default_mode>; |
| 266 |
pinctrl-1 = <&mc0_a_1_sleep>; |
| 267 |
|
| 268 |
/* GPIO218 MMC_CD */ |
| 269 |
cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>; |
| 270 |
|
| 271 |
status = "okay"; |
| 272 |
}; |
| 273 |
|
| 274 |
// WLAN SDIO channel |
| 275 |
mmc@80118000 { |
| 276 |
arm,primecell-periphid = <0x10480180>; |
| 277 |
max-frequency = <100000000>; |
| 278 |
bus-width = <4>; |
| 279 |
pinctrl-names = "default", "sleep"; |
| 280 |
pinctrl-0 = <&mc1_a_1_default>; |
| 281 |
pinctrl-1 = <&mc1_a_1_sleep>; |
| 282 |
|
| 283 |
status = "okay"; |
| 284 |
}; |
| 285 |
|
| 286 |
// Unused PoP eMMC - register and put it to sleep by default */ |
| 287 |
mmc@80005000 { |
| 288 |
arm,primecell-periphid = <0x10480180>; |
| 289 |
pinctrl-names = "default"; |
| 290 |
pinctrl-0 = <&mc2_a_1_sleep>; |
| 291 |
|
| 292 |
status = "okay"; |
| 293 |
}; |
| 294 |
|
| 295 |
// On-board eMMC |
| 296 |
mmc@80114000 { |
| 297 |
arm,primecell-periphid = <0x10480180>; |
| 298 |
max-frequency = <100000000>; |
| 299 |
bus-width = <8>; |
| 300 |
cap-mmc-highspeed; |
| 301 |
no-sdio; |
| 302 |
no-sd; |
| 303 |
vmmc-supply = <&ab8500_ldo_aux2_reg>; |
| 304 |
pinctrl-names = "default", "sleep"; |
| 305 |
pinctrl-0 = <&mc4_a_1_default>; |
| 306 |
pinctrl-1 = <&mc4_a_1_sleep>; |
| 307 |
|
| 308 |
status = "okay"; |
| 309 |
}; |
| 310 |
|
| 311 |
serial@80120000 { |
| 312 |
pinctrl-names = "default", "sleep"; |
| 313 |
pinctrl-0 = <&u0_a_1_default>; |
| 314 |
pinctrl-1 = <&u0_a_1_sleep>; |
| 315 |
status = "okay"; |
| 316 |
}; |
| 317 |
|
| 318 |
/* This UART is unused and thus left disabled */ |
| 319 |
serial@80121000 { |
| 320 |
pinctrl-names = "default", "sleep"; |
| 321 |
pinctrl-0 = <&u1rxtx_a_1_default>; |
| 322 |
pinctrl-1 = <&u1rxtx_a_1_sleep>; |
| 323 |
}; |
| 324 |
|
| 325 |
serial@80007000 { |
| 326 |
pinctrl-names = "default", "sleep"; |
| 327 |
pinctrl-0 = <&u2rxtx_c_1_default>; |
| 328 |
pinctrl-1 = <&u2rxtx_c_1_sleep>; |
| 329 |
status = "okay"; |
| 330 |
}; |
| 331 |
|
| 332 |
i2c@80004000 { |
| 333 |
pinctrl-names = "default","sleep"; |
| 334 |
pinctrl-0 = <&i2c0_a_1_default>; |
| 335 |
pinctrl-1 = <&i2c0_a_1_sleep>; |
| 336 |
status = "okay"; |
| 337 |
}; |
| 338 |
|
| 339 |
i2c@80122000 { |
| 340 |
pinctrl-names = "default","sleep"; |
| 341 |
pinctrl-0 = <&i2c1_b_2_default>; |
| 342 |
pinctrl-1 = <&i2c1_b_2_sleep>; |
| 343 |
status = "okay"; |
| 344 |
}; |
| 345 |
|
| 346 |
i2c@80128000 { |
| 347 |
pinctrl-names = "default","sleep"; |
| 348 |
pinctrl-0 = <&i2c2_b_2_default>; |
| 349 |
pinctrl-1 = <&i2c2_b_2_sleep>; |
| 350 |
status = "okay"; |
| 351 |
lsm303dlh@18 { |
| 352 |
/* Accelerometer */ |
| 353 |
compatible = "st,lsm303dlh-accel"; |
| 354 |
st,drdy-int-pin = <1>; |
| 355 |
reg = <0x18>; |
| 356 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 357 |
vddio-supply = <&db8500_vsmps2_reg>; |
| 358 |
pinctrl-names = "default"; |
| 359 |
pinctrl-0 = <&accel_snowball_mode>; |
| 360 |
interrupt-parent = <&gpio5>; |
| 361 |
interrupts = <3 IRQ_TYPE_EDGE_RISING>, /* INT1 */ |
| 362 |
<4 IRQ_TYPE_EDGE_RISING>; /* INT2 */ |
| 363 |
}; |
| 364 |
lsm303dlh@1e { |
| 365 |
/* Magnetometer */ |
| 366 |
compatible = "st,lsm303dlh-magn"; |
| 367 |
reg = <0x1e>; |
| 368 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 369 |
vddio-supply = <&db8500_vsmps2_reg>; |
| 370 |
pinctrl-names = "default"; |
| 371 |
pinctrl-0 = <&magneto_snowball_mode>; |
| 372 |
interrupt-parent = <&gpio5>; |
| 373 |
interrupts = <5 IRQ_TYPE_EDGE_RISING>; /* DRDY line */ |
| 374 |
}; |
| 375 |
l3g4200d@68 { |
| 376 |
/* Gyroscope */ |
| 377 |
compatible = "st,l3g4200d-gyro"; |
| 378 |
st,drdy-int-pin = <2>; |
| 379 |
reg = <0x68>; |
| 380 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 381 |
vddio-supply = <&db8500_vsmps2_reg>; |
| 382 |
pinctrl-names = "default"; |
| 383 |
pinctrl-0 = <&gyro_snowball_mode>; |
| 384 |
interrupt-parent = <&gpio5>; |
| 385 |
interrupts = <6 IRQ_TYPE_EDGE_RISING>, /* DRDY line */ |
| 386 |
<9 IRQ_TYPE_EDGE_RISING>; /* INT1 */ |
| 387 |
}; |
| 388 |
lsp001wm@5c { |
| 389 |
/* Barometer/pressure sensor */ |
| 390 |
compatible = "st,lps001wp-press"; |
| 391 |
reg = <0x5c>; |
| 392 |
vdd-supply = <&ab8500_ldo_aux1_reg>; |
| 393 |
vddio-supply = <&db8500_vsmps2_reg>; |
| 394 |
}; |
| 395 |
}; |
| 396 |
|
| 397 |
i2c@80110000 { |
| 398 |
pinctrl-names = "default","sleep"; |
| 399 |
pinctrl-0 = <&i2c3_c_2_default>; |
| 400 |
pinctrl-1 = <&i2c3_c_2_sleep>; |
| 401 |
status = "okay"; |
| 402 |
}; |
| 403 |
|
| 404 |
spi@80002000 { |
| 405 |
pinctrl-names = "default"; |
| 406 |
pinctrl-0 = <&ssp0_snowball_mode>; |
| 407 |
status = "okay"; |
| 408 |
}; |
| 409 |
|
| 410 |
prcmu@80157000 { |
| 411 |
ab8500 { |
| 412 |
gpio { |
| 413 |
/* |
| 414 |
* AB8500 GPIOs are numbered starting from 1, so the first |
| 415 |
* index 0 is what in the datasheet is called "GPIO1", and |
| 416 |
* the second is "GPIO2" and so forth. Confusingly, the |
| 417 |
* Snowball schematic then names the "GPIO2" line "PM_GPIO1". |
| 418 |
* while later naming "GPIO4" as "PM_GPIO4". |
| 419 |
*/ |
| 420 |
gpio-line-names = "", /* AB8500 GPIO1 */ |
| 421 |
"PM_GPIO1", /* AB8500 GPIO2 */ |
| 422 |
"WLAN_CLK_REQ", /* AB8500 GPIO3 */ |
| 423 |
"PM_GPIO4", /* AB8500 GPIO4 */ |
| 424 |
"", "", "", "", "", "", "", "", "", "", "", |
| 425 |
"EN_3V6", /* AB8500 GPIO16 */ |
| 426 |
"", "", "", "" ,"", "", "", "", "", |
| 427 |
"EN_3V3", /* AB8500 GPIO26 */ |
| 428 |
"", "", "", "", "", "", "", "", "", "", "", "", "", |
| 429 |
"PM_GPIO40", /* AB8500 GPIO40 */ |
| 430 |
"PM_GPIO41", /* AB8500 GPIO41 */ |
| 431 |
"PM_GPIO42"; /* AB8500 GPIO42 */ |
| 432 |
}; |
| 433 |
|
| 434 |
phy { |
| 435 |
pinctrl-names = "default", "sleep"; |
| 436 |
pinctrl-0 = <&usb_a_1_default>; |
| 437 |
pinctrl-1 = <&usb_a_1_sleep>; |
| 438 |
}; |
| 439 |
|
| 440 |
ext_regulators: regulator-external { |
| 441 |
ab8500_ext1_reg: ab8500_ext1 { |
| 442 |
regulator-name = "ab8500-ext-supply1"; |
| 443 |
}; |
| 444 |
|
| 445 |
ab8500_ext2_reg_reg: ab8500_ext2 { |
| 446 |
regulator-name = "ab8500-ext-supply2"; |
| 447 |
}; |
| 448 |
|
| 449 |
ab8500_ext3_reg_reg: ab8500_ext3 { |
| 450 |
regulator-name = "ab8500-ext-supply3"; |
| 451 |
}; |
| 452 |
}; |
| 453 |
|
| 454 |
regulator { |
| 455 |
ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { |
| 456 |
regulator-name = "V-DISPLAY"; |
| 457 |
}; |
| 458 |
|
| 459 |
ab8500_ldo_aux2_reg: ab8500_ldo_aux2 { |
| 460 |
regulator-name = "V-eMMC1"; |
| 461 |
}; |
| 462 |
|
| 463 |
ab8500_ldo_aux3_reg: ab8500_ldo_aux3 { |
| 464 |
regulator-name = "V-MMC-SD"; |
| 465 |
}; |
| 466 |
|
| 467 |
ab8500_ldo_intcore_reg: ab8500_ldo_intcore { |
| 468 |
regulator-name = "V-INTCORE"; |
| 469 |
}; |
| 470 |
|
| 471 |
ab8500_ldo_tvout_reg: ab8500_ldo_tvout { |
| 472 |
regulator-name = "V-TVOUT"; |
| 473 |
}; |
| 474 |
|
| 475 |
ab8500_ldo_audio_reg: ab8500_ldo_audio { |
| 476 |
regulator-name = "V-AUD"; |
| 477 |
}; |
| 478 |
|
| 479 |
ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 { |
| 480 |
regulator-name = "V-AMIC1"; |
| 481 |
}; |
| 482 |
|
| 483 |
ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 { |
| 484 |
regulator-name = "V-AMIC2"; |
| 485 |
}; |
| 486 |
|
| 487 |
ab8500_ldo_dmic_reg: ab8500_ldo_dmic { |
| 488 |
regulator-name = "V-DMIC"; |
| 489 |
}; |
| 490 |
|
| 491 |
ab8500_ldo_ana_reg: ab8500_ldo_ana { |
| 492 |
regulator-name = "V-CSI/DSI"; |
| 493 |
}; |
| 494 |
}; |
| 495 |
}; |
| 496 |
}; |
| 497 |
|
| 498 |
pinctrl { |
| 499 |
/* |
| 500 |
* Set this up using hogs, as time goes by and as seems fit, these |
| 501 |
* can be moved over to being controlled by respective device. |
| 502 |
*/ |
| 503 |
pinctrl-names = "default"; |
| 504 |
pinctrl-0 = <&gbf_snowball_mode>, |
| 505 |
<&wlan_snowball_mode>; |
| 506 |
|
| 507 |
ethernet { |
| 508 |
/* |
| 509 |
* Mux in "SM" which is used for the |
| 510 |
* SMSC911x Ethernet adapter |
| 511 |
*/ |
| 512 |
eth_snowball_mode: eth_snowball { |
| 513 |
snowball_mux { |
| 514 |
function = "sm"; |
| 515 |
groups = "sm_b_1"; |
| 516 |
}; |
| 517 |
/* LAN IRQ pin */ |
| 518 |
snowball_cfg1 { |
| 519 |
pins = "GPIO140_B11"; |
| 520 |
ste,config = <&in_nopull>; |
| 521 |
}; |
| 522 |
/* LAN reset pin */ |
| 523 |
snowball_cfg2 { |
| 524 |
pins = "GPIO141_C12"; |
| 525 |
ste,config = <&gpio_out_hi>; |
| 526 |
}; |
| 527 |
|
| 528 |
}; |
| 529 |
}; |
| 530 |
sdi0 { |
| 531 |
sdi0_default_mode: sdi0_default { |
| 532 |
snowball_mux { |
| 533 |
function = "mc0"; |
| 534 |
/* Add the DAT31 pin even if it is not really used */ |
| 535 |
groups = "mc0dat31dir_a_1"; |
| 536 |
}; |
| 537 |
snowball_cfg1 { |
| 538 |
pins = "GPIO21_AB3"; /* DAT31DIR */ |
| 539 |
ste,config = <&out_hi>; |
| 540 |
}; |
| 541 |
/* SD card detect GPIO pin, extend default state */ |
| 542 |
snowball_cfg2 { |
| 543 |
pins = "GPIO218_AH11"; |
| 544 |
ste,config = <&gpio_in_pu>; |
| 545 |
}; |
| 546 |
/* VMMCI level-shifter enable */ |
| 547 |
snowball_cfg3 { |
| 548 |
pins = "GPIO217_AH12"; |
| 549 |
ste,config = <&gpio_out_hi>; |
| 550 |
}; |
| 551 |
/* VMMCI level-shifter voltage select */ |
| 552 |
snowball_cfg4 { |
| 553 |
pins = "GPIO228_AJ6"; |
| 554 |
ste,config = <&gpio_out_hi>; |
| 555 |
}; |
| 556 |
}; |
| 557 |
}; |
| 558 |
ssp0 { |
| 559 |
ssp0_snowball_mode: ssp0_snowball_default { |
| 560 |
snowball_mux { |
| 561 |
function = "ssp0"; |
| 562 |
groups = "ssp0_a_1"; |
| 563 |
}; |
| 564 |
snowball_cfg1 { |
| 565 |
pins = "GPIO144_B13"; /* FRM */ |
| 566 |
ste,config = <&gpio_out_hi>; |
| 567 |
}; |
| 568 |
snowball_cfg2 { |
| 569 |
pins = "GPIO145_C13"; /* RXD */ |
| 570 |
ste,config = <&in_pd>; |
| 571 |
}; |
| 572 |
snowball_cfg3 { |
| 573 |
pins = |
| 574 |
"GPIO146_D13", /* TXD */ |
| 575 |
"GPIO143_D12"; /* CLK */ |
| 576 |
ste,config = <&out_lo>; |
| 577 |
}; |
| 578 |
|
| 579 |
}; |
| 580 |
}; |
| 581 |
gpio_led { |
| 582 |
gpioled_snowball_mode: gpioled_default { |
| 583 |
snowball_cfg1 { |
| 584 |
pins = "GPIO142_C11"; |
| 585 |
ste,config = <&gpio_out_hi>; |
| 586 |
}; |
| 587 |
|
| 588 |
}; |
| 589 |
}; |
| 590 |
accelerometer { |
| 591 |
accel_snowball_mode: accel_snowball { |
| 592 |
/* Accelerometer lines */ |
| 593 |
snowball_cfg1 { |
| 594 |
pins = |
| 595 |
"GPIO163_C20", /* ACCEL_IRQ1 */ |
| 596 |
"GPIO164_B21"; /* ACCEL_IRQ2 */ |
| 597 |
ste,config = <&gpio_in_pu>; |
| 598 |
}; |
| 599 |
}; |
| 600 |
}; |
| 601 |
gyro { |
| 602 |
gyro_snowball_mode: gyro_snowball { |
| 603 |
snowball_cfg1 { |
| 604 |
pins = |
| 605 |
"GPIO166_A22", /* DRDY */ |
| 606 |
"GPIO169_D22"; /* INT */ |
| 607 |
ste,config = <&gpio_in_pu>; |
| 608 |
}; |
| 609 |
}; |
| 610 |
}; |
| 611 |
magnetometer { |
| 612 |
magneto_snowball_mode: magneto_snowball { |
| 613 |
snowball_cfg1 { |
| 614 |
pins = "GPIO165_C21"; /* MAG_DRDY */ |
| 615 |
ste,config = <&gpio_in_pu>; |
| 616 |
}; |
| 617 |
}; |
| 618 |
}; |
| 619 |
gbf { |
| 620 |
gbf_snowball_mode: gbf_snowball { |
| 621 |
/* |
| 622 |
* GBF (GPS, Bluetooth, FM-radio) interface, |
| 623 |
* pull low to reset state |
| 624 |
*/ |
| 625 |
snowball_cfg1 { |
| 626 |
pins = "GPIO171_D23"; /* GBF_ENA_RESET */ |
| 627 |
ste,config = <&gpio_out_lo>; |
| 628 |
}; |
| 629 |
}; |
| 630 |
}; |
| 631 |
wlan { |
| 632 |
wlan_snowball_mode: wlan_snowball { |
| 633 |
/* |
| 634 |
* Activate this mode with the WLAN chip. |
| 635 |
* These are plain GPIO pins used by WLAN |
| 636 |
*/ |
| 637 |
snowball_cfg1 { |
| 638 |
pins = |
| 639 |
"GPIO161_D21", /* WLAN_PMU_EN */ |
| 640 |
"GPIO215_AH13"; /* WLAN_ENA */ |
| 641 |
ste,config = <&gpio_out_lo>; |
| 642 |
}; |
| 643 |
snowball_cfg2 { |
| 644 |
pins = "GPIO216_AG12"; /* WLAN_IRQ */ |
| 645 |
ste,config = <&gpio_in_pu>; |
| 646 |
}; |
| 647 |
}; |
| 648 |
}; |
| 649 |
}; |
| 650 |
|
| 651 |
mcde@a0350000 { |
| 652 |
pinctrl-names = "default", "sleep"; |
| 653 |
pinctrl-0 = <&lcd_default_mode>; |
| 654 |
pinctrl-1 = <&lcd_sleep_mode>; |
| 655 |
}; |
| 656 |
}; |
| 657 |
}; |