Debian Codegraph @

arch/arm/boot/dts/st/stm32mp153c-lxa-fairytux2-gen2.dts

raw
1 // SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
2 /*
3 * Copyright (C) 2024 Leonard Göhrs, Pengutronix
4 */
5
6 /dts-v1/;
7
8 #include "stm32mp153c-lxa-fairytux2.dtsi"
9
10 / {
11 model = "Linux Automation GmbH FairyTux 2 Gen 2";
12 compatible = "lxa,stm32mp153c-fairytux2-gen2", "oct,stm32mp153x-osd32", "st,stm32mp153";
13
14 gpio-keys {
15 compatible = "gpio-keys";
16
17 button-left {
18 label = "USER_BTN1";
19 linux,code = <KEY_ESC>;
20 gpios = <&gpioi 10 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
21 };
22
23 button-right {
24 label = "USER_BTN2";
25 linux,code = <KEY_HOME>;
26 gpios = <&gpioe 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
27 };
28 };
29 };
30
31 &gpiof {
32 gpio-line-names = "", "", "", "", "", /* 0 */
33 "", "", "", "", "", /* 5 */
34 "", "", "", "", "", /* 10 */
35 ""; /* 15 */
36 };
37
38 &gpioh {
39 gpio-line-names = "", "", "", "", "LCD_RESET", /* 0 */
40 "", "", "", "", "", /* 5 */
41 "", "", "GPIO1", "GPIO_INT", "", /* 10 */
42 ""; /* 15 */
43 };
44
45 &gpioi {
46 gpio-line-names = "GPIO2", "", "", "", "", /* 0 */
47 "", "", "", "ETH_", "", /* 5 */
48 "", "USER_BTN1"; /* 10 */
49 };
50
51 &i2c1 {
52 pinctrl-names = "default", "sleep";
53 pinctrl-0 = <&i2c1_pins_b>;
54 pinctrl-1 = <&i2c1_sleep_pins_b>;
55 status = "okay";
56
57 io_board_gpio: gpio@20 {
58 compatible = "ti,tca6408";
59 reg = <0x20>;
60 gpio-controller;
61 #gpio-cells = <2>;
62 interrupt-parent = <&gpioh>;
63 interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
64 interrupt-controller;
65 pinctrl-names = "default";
66 pinctrl-0 = <&board_tca6408_pins>;
67 #interrupt-cells = <2>;
68 vcc-supply = <&v3v3_hdmi>;
69 gpio-line-names = "LED1_GA_YK", "LED2_GA_YK", "LED1_GK_YA", "USB_CC_ALERT",
70 "RS485_EN", "RS485_120R", "USB_CC_RESET", "CAN_120R";
71 };
72
73 usb_c: typec@28 {
74 compatible = "st,stusb1600";
75 reg = <0x28>;
76 interrupt-parent = <&io_board_gpio>;
77 interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
78 vdd-supply = <&reg_5v>;
79 vsys-supply = <&v3v3_hdmi>;
80
81 connector {
82 compatible = "usb-c-connector";
83 label = "USB-C";
84 power-role = "dual";
85 typec-power-opmode = "default";
86
87 port {
88 con_usbotg_hs_ep: endpoint {
89 remote-endpoint = <&usbotg_hs_ep>;
90 };
91 };
92 };
93 };
94
95 temperature-sensor@48 {
96 compatible = "national,lm75a";
97 reg = <0x48>;
98 /*
99 * The sensor itself is powered by a voltage divider from the
100 * always-on 5V supply.
101 * The required pull-up resistors however are on v3v3_hdmi.
102 */
103 vs-supply = <&v3v3_hdmi>;
104 };
105
106 io_board_eeprom: eeprom@56 {
107 compatible = "atmel,24c04";
108 reg = <0x56>;
109 vcc-supply = <&v3v3_hdmi>;
110 };
111 };
112
113 &rtc {
114 status = "okay";
115 };
116
117 &led_controller_io {
118 led-2 {
119 color = <LED_COLOR_ID_ORANGE>;
120 function = LED_FUNCTION_ACTIVITY;
121 gpios = <&io_board_gpio 1 GPIO_ACTIVE_LOW>;
122 };
123 };
124
125 &usart3 {
126 rts-gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
127 cts-gpios = <&gpiod 11 GPIO_ACTIVE_LOW>;
128 };
129
130 &usbotg_hs {
131 usb-role-switch;
132
133 port {
134 usbotg_hs_ep: endpoint {
135 remote-endpoint = <&con_usbotg_hs_ep>;
136 };
137 };
138 };
139
140 &pinctrl {
141 board_tca6408_pins: stusb1600-0 {
142 pins {
143 pinmux = <STM32_PINMUX('H', 13, GPIO)>;
144 bias-pull-up;
145 };
146 };
147 };